GE Fanuc Automation. Series 0i Model A. Computer Numerical Control Products. Parameter Manual

Transcription

1 GE Fanuc Automation Computer Numerical Control Products Series 0i Model A Parameter Manual GFZ-63510EN/01 June 2000

2 Warnings, Cautions, and Notes as Used in this Publication GFL-001 Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply. Copyright 2000 GE Fanuc Automation North America, Inc. All Rights Reserved.

3 PREFACE The mode covered by this manual, and their abbreviations are : Product Name FANUC Series 0i TA FANUC Series 0i MA 0i TA 0i MA Abbreviations Series 0i NOTE 1 For ease of understanding, the models are categorized as follows: T series: 0i TA M series: 0i MA 2 Some functions described in this manual may not be applied to some products. For details, refer to the DESCRIPTIONS manual (B 63502EN). Related Manuals The table below lists manuals related to MODEL A of Series 0i. In the table, this manual is marked with an asterisk (*). Table 1 Related manuals Manual name Specification Number DESCRIPTIONS CONNECTION MANUAL (HARDWARE) CONNECTION MANUAL (FUNCTION) OPERATOR S MANUAL For Lathe OPERATOR S MANUAL For Maching Center MAINTENANCE MANUAL B 63502EN B 63503EN B 63503EN 1 B 63504EN B 63514EN B 63505EN PARAMETER MANUAL B 63510EN * PROGRAMMING MANUAL (Macro Compiler/Macro Executer) FAPT MACRO COMPILER PROGRAMMING MANUAL B 61803E 1 B 66102E p 1

4 Table of Contents PREFACE p 1 1. DISPLAYING PARAMETERS SETTING PARAMETERS FROM MDI INPUTTING AND OUTPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE OUTPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE INPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE DESCRIPTION OF PARAMETERS PARAMETERS OF SETTING PARAMETERS OF READER/PUNCHER INTERFACE Parameters Common to all Channels Parameters of Channel 1 (I/O CHANNEL=0) Parameters of Channel 1 (I/O CHANNEL=1) Parameters of Channel 2 (I/O CHANNEL=2) PARAMETERS OF POWER MOTION MANAGER PARAMETERS OF AXIS CONTROL/INCREMENT SYSTEM PARAMETERS OF COORDINATES PARAMETERS OF STROKE CHECK PARAMETERS OF FEEDRATE PARAMETERS OF ACCELERATION/DECELERATION CONTROL PARAMETERS OF SERVO PARAMETERS OF DI/DO PARAMETERS OF MDI, DISPLAY, AND EDIT PARAMETERS OF PROGRAMS PARAMETERS OF PITCH ERROR COMPENSATION PARAMETERS OF SPINDLE CONTROL PARAMETERS OF TOOL COMPENSATION PARAMETERS OF CANNED CYCLES Parameter of canned Cycle for Drilling Parameter of Thread Cutting Cycle Parameter of Multiple Repetitive Canned Cycle Parameters of Peck Drilling Cycle of a Small Diameter PARAMETERS OF RIGID TAPPING PARAMETERS OF SCALING/COORDINATE ROTATION PARAMETERS OF UNI DIRECTIONAL POSITIONING PARAMETERS OF POLAR COORDINATE INTERPOLATION PARAMETERS OF NORMAL DIRECTION CONTROL PARAMETERS OF INDEXING INDEX TABLE PARAMETERS OF CUSTOM MACROS PARAMETERS OF PATTERN DATA INPUT PARAMETERS OF SKIP FUNCTION c 1

5 Table of Contents 4.26 PARAMETERS OF AUTOMATIC TOOL COMPENSATION (T SERIES) AND AUTOMATIC TOOL LENGTH COMPENSATION (M SERIES) PARAMETERS OF EXTERNAL DATA INPUT/OUTPUT PARAMETERS OF GRAPHIC DISPLAY PARAMETERS OF DISPLAYING OPERATION TIME AND NUMBER OF PARTS PARAMETERS OF TOOL LIFE MANAGEMENT PARAMETERS OF POSITION SWITCH FUNCTIONS PARAMETERS OF MANUAL OPERATION AND AUTOMATIC OPERATION PARAMETERS OF MANUAL HANDLE FEED AND HANDLE INTERRUPTION PARAMETERS OF REFERENCE POSITION SETTING WITH MECHANICAL STOPPER PARAMETERS OF SOFTWARE OPERATOR S PANEL PARAMETERS OF PROGRAM RESTART PARAMETERS OF POLYGON TURNING PARAMETERS OF AXIS CONTROL BY PMC PARAMETERS RELATED TO THE BASIC FUNCTIONS PARAMETERS OF SIMPLE SYNCHRONOUS CONTROL PARAMETERS OF CHECK TERMINATION OTHER PARAMETERS PARAMETERS OF MAINTENANCE APPENDIX A. CHARACTER CODE LIST c 2

6 1. DISPLAYING PARAMETERS 1 DISPLAYING PARAMETERS Follow the procedure below to display parameters. (1) Press the <SYSTEM> function key on the MDI as many times as required, or alternatively, press the <SYSTEM> function key once, then the [PARAM] section display soft key. The parameter screen is then selected. PARAMETER (FEEDRATE) O0001 N12345 PROG OFFSET SETTING CUSTOM 1401 RDR JZR RF0 LRP RPD DLF HFC DRY RUN FEEDRATE INIT.CUTTING F RAPID FEEDRATE X Y Z SYSTEM MESSAGE GRAPH Cursor Function key > MEM STRT MTN FIN *** 10:02:35 [PARAM] [DGNOS] [ PMC ] [SYSTEM] [(OPRT)] Soft key display (section select) Return menu key Soft key Continuous menu key (2) The parameter screen consists of multiple pages. Use step (a) or (b) to display the page that contains the parameter you want to display. (a) Use the page select key or the cursor move keys to display the desired page. (b) Enter the data number of the parameter you want to display from the keyboard, then press the [NO.SRH] soft key. The parameter page containing the specified data number appears with the cursor positioned at the data number. (The data is displayed in reverse video.) NOTE If key entry is started with the section select soft keys displayed, they are replaced automatically by operation select soft keys including [NO.SRH]. Pressing the [(OPRT)] soft key can also cause the operation select keys to be displayed. > MEM STRT MTN FIN *** 10:02:34 [NO.SRH] [ ON:1 ] [ OFF:0 ] [+INPUT] [INPUT ] Data entered from the keyboard Soft key display (section select) 1

7