Lesson 14 Blends. For Resources go to > click on the Creo Parametric 2.0 Book cover

Size: px
Start display at page:

Download "Lesson 14 Blends. For Resources go to > click on the Creo Parametric 2.0 Book cover"

Transcription

1 Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Hole Pattern REFERENCES AND RESOURCES For Resources go to > click on the Creo Parametric 2.0 Book cover Lesson 14 Lecture Book Projects PDF Project Lectures Creo Parametric 2.0 Quick Reference Card Creo Parametric 2.0 Configuration Options BLENDS A blended feature consists of a series of at least two planar sections that are joined together at their edges with transitional surfaces to form a continuous feature. The Cap in Figure 14.1 uses a simple blend feature in its design. A Blend can be created as a Parallel Blend as used here, or you can construct a Swept Blend. Blend Sections Blended surfaces are created between the corresponding sections. Figure 14.2 shows a parallel blend for which the section consists of several subsections. Each segment in the subsection is matched with a segment in the following subsection; to create the transitional surfaces; Creo Parametric 2.0 connects the starting points of the subsections and continues to connect the vertices of the subsections in a clockwise manner. By changing the starting point of a blend subsection, you can create blended surfaces that twist between the subsections. The default starting point is the first point sketched in the subsection Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 629

2 Figure 14.2 Blend Sections (CADTRAIN, COAch for Creo Parametric 2.0) Blend Options Blends (Fig. 14.3) use one of the following transitional surface options: Straight Create a straight blend by connecting vertices of different subsections with straight lines. Edges of the sections are connected with ruled surfaces. Smooth Create a smooth blend by connecting vertices of different subsections with smooth curves. Edges of the sections are connected with ruled (spline) surfaces. Parallel All blend sections lie on parallel planes in one section sketch. Rotational The blend sections are rotated about the Y axis, up to a maximum of 120. Each section is sketched individually and aligned using the coordinate system of the section. General The sections of a general blend can be rotated about and translated along the X, Y, and Z axes. Sections are sketched individually and aligned using the coordinate system of the section. Regular Sec The feature will use the regular sketching plane. Project Sec The feature will use the projection of the section on the selected surface. This is used for parallel blends only. Select Sec Select section entities (not available for parallel blends). Sketch Sec Sketch section entities Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 630

3 Figure 14.3 Blend Sections Parallel Blends A parallel blend is created from a single section that contains multiple sketches called subsections (Fig. 14.4). A first or last subsection can be defined as a point resulting in a blend vertex. The starting point for each subsection must be selected as per the design requirements including the starting points (Fig. 14.5). Figure 14.4 Starting Points Figure 14.5 Starting Points 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 631

4 Lesson 14 STEPS Figure 14.6 Cap Drawing Cap The Cap (Fig. 14.6) is a part created with a Parallel Blend (Fig. 14.7). The blend sections are a circle and a triangle. Because the sections of a blend must have equal segments, the circle is actually three equal arcs [Fig. 14.8(a)]. The part is shelled as the last feature in its creation [Fig (b)]. Figure 14.7 Cap 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 632

5 Start a new part. Click: > cap > OK Model Properties: Material = PVC (pvc.mtl) Units = Inch lbm Second Set Datum and Rename the default datum planes and coordinate system: Datum FRONT = A Datum RIGHT = B Datum TOP = C Coordinate System = CSYS_CAP File > Options > Configuration Editor > Display Filters > > Find > 1. Type keyword, type default_dec_places > Find Now > 3. Set value, type 3 > Enter > Close > OK > No Figure 14.8(a) Front View 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 633

6 Figure 14.8(b) Right Side View 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 634

7 For Lessons 13-18, step-by-step commands are limited to new software commands introduced or enhanced in that lesson. You will be expected to do most of the modeling using commands and practices mastered from Lessons 1-12 without repeated detailed explanations. Refer to Figures 14.8(a-b) for the Cap dimensions. Model the circular protrusion that is 9.00 by.25 thick shown in (Fig. 14.9). Sketch the first protrusion on datum A (FRONT) and centered on B (RIGHT) and C (TOP). Figure 14.9 First Protrusion Create the blend protrusion, click: Model tab > Shapes Group > Blend > Options tab > Smooth > Sections tab > Define > Done > select the forward face of the first protrusion [Fig (a)] > Flip > Sketch > Figure 14.10(a) Blend Feature Starting Surface 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 635

8 Click: File > Options > Sketcher > > > OK > No > Sketch tab > Setup Group > Display > Setup Group > [Fig (b)] > Grid Type > Grid Spacing > Radial Spacing.50 > Enter > Angular 30 > Enter [Fig (c)] > OK [Fig (d)] > Hidden Line > add vertical and horizontal construction centerlines, start the centerlines at the origin [Fig (e)] Figure 14.10(b) Grid Settings Dialog Box Figure 14.10(c) Polar Grid Settings Figure 14.10(d) Sketcher Showing Polar Grid Figure 14.10(e) Vertical and Horizontal Centerlines 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 636

9 Add two 30-degree construction centerlines, start the centerlines at the origin [Figs (f-g)] Figure 14.10(f) Sketch 30 Degree Centerline Figure 14.10(g) Sketch the Second 30 Degree Centerline Sketch the first section of the blend by creating three equal 120 arcs, click: > flyout > Create an arc by picking its center and endpoints > sketch the first arc by picking its center, its first end point along datum B, moving your pointer in a counter clockwise direction, and its last end point along one of the 30-degree centerlines [Fig (h)] > sketch the second arc by picking its center and end points following the counter clockwise direction [Fig (i)] Figure 14.10(h) First 120-degree Arc Figure 14.10(i) Second 120-degree Arc 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 637

10 Sketch the third arc by picking its center and end points > MMB to end the current tool [Fig (j)] (the arc dimension is a radius value) > LMB to deselect > press RMB > Dimension > double-click on the arc > MMB to place the diameter dimension > LMB to accept the default value [Fig (k)] Note the location of the start point for this section > Figure 14.10(j) Third 120-degree Arc Figure 14.10(k) Diameter Dimension 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 638

11 Click: File > Options > Sketcher > set values and options as in Figure 14.10(l)] > OK > No > Sections tab > Section 2 > Offset from 3.00 > Enter > Sketch [Fig (m)] Figure 14.10(l) Sketcher grid Settings Figure 14.10(m) Sketch Three Lines 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 639

12 Click: add two 30-degree construction centerlines, start the centerlines at the origin > sketch the second parallel section (the first section is grayed out) RMB > Line Chain > sketch the three lines of the triangle starting at the top so that the start point is near the start point of the first section and picking points in the same direction in which the arcs were created [Fig (n)] > add the three dimensions [Fig (o)]> Equal > select the two angled lines > Delete from the Resolve Sketch dialog box > select the horizontal line [Fig (o)] > select and Delete the angled length dimension from the Resolve Sketch dialog box > MMB > MMB Figure 14.10(n) Second Section Figure 14.10(o) Three Length Dimensions Figure 14.10(o) Dimensioned Sketch 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 640

13 Click: File > Options > Sketcher > turn off the grid and grid snap > OK > No > modify and the length to 3.00 > RMB >Dimension > add one 120-degree dimension back to the sketch by clicking on the vertical centerline and then the angled centerline > MMB to place the dimension [Fig (p)] > Dim-Ref [Fig (q)] > Ctrl+D Figure 14.10(p) 120-degree Reference Dimension Figure 14.10(q) Section Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 641

14 Click: [Fig (r)] > [Fig (s)] > select both sections of the blend in the Model Tree > press RMB > Edit > modify the diameter to 6.50 > Enter > LMB to deselect and regenerate > Ctrl+S > OK Fig (t)] Figure 14.10(r) Blend Figure 14.10(s) Blend Preview 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 642

15 Figure 14.10(t) Completed Blend Create and pattern the six equally spaced holes.400 on a 7.75 bolt circle, click: the hole with the options and references [Fig (a)] > LMB to deselect > complete Figure 14.11(a) Hole Options and References (your axis name may be different) 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 643

16 Click on the hole in the Model Tree > RMB > Pattern > complete the pattern with the options and references [Fig (b)] (use the 30 degree dimension to pattern) [Fig (c)] Figure 14.11(b) Patterning the Hole Figure 14.11(c) Completed Hole Pattern 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 644

17 Click: > spin the model > select the bottom surface of the part as the surface to remove [Fig (a)] > Thickness.125 > Enter > [Fig (b)] Figure 14.12(a) Shell Tool Figure 14.12(b) Completed Shell 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 645

18 Click on > Ctrl+D > Ctrl+S > OK in the Model Tree and move (drag) it below the Shell feature [Figs (a-b)] Figure 14.13(a) Move the Pattern after the Shell Figure 14.13(b) Moved Pattern 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 646

19 Press: Ctrl+N > > type: cap > > OK > OK > Layout tab > > Sheet 1 Format > > Browse > > Open > OK [Fig (a)] > Ctrl+S > Enter > > all off > LMB in the Graphics Window > select the top view > press RMB > off > press RMB > Delete Figure 14.14(a) Cap Drawing Click: File > Prepare > Drawing Properties > Detail Options change > Option: type gtol > Enter > Value: > std_asme [Fig (b)] > Add/Change > Apply > Close > Close Figure 14.14(b) Show Model Annotations 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 647

20 Click: Annotate tab > Show Model Annotations > select the front view > press Ctrl key > select the right side view > release the Ctrl key > check the dimensions required for the detail [Figs (c-e)] > Apply Figure 14.14(c) Model Annotations Figure 14.14(d) Checked Dimensions Figure 14.14(e) Right Side View 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 648

21 Click: tab [Fig (f)] > > Apply > tab [Fig (g)] > > Apply > (close the dialog) > [Fig (h)] > modify and reposition the annotations as required [Fig (i)] Figure 14.14(f) Axes Figure 14.14(g) Notes Figure 14.14(h) Shown Model Annotations before Repositioning 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 649

22 Click: > Ctrl+S > OK [Fig (j)] > File > Manage File > Delete Old Versions > Enter > File > Save As > Type > > Zip File (*.zip) > OK > upload the zip file to your course interface or attach to an and send to your instructor and/or yourself > File > Close > File > Exit >Yes Figure 14.14(i) Modified and Repositioned Annotations Figure 14.14(j) Completed Detail Drawing For additional projects, see > click on the image of your book cover Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part. 650

Lesson 14 Blends. For Resources go to > click on the Creo Parametric Book cover

Lesson 14 Blends. For Resources go to  > click on the Creo Parametric Book cover Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Swept Blend REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo

More information

Lesson 17 Shell, Reorder, and Insert Mode

Lesson 17 Shell, Reorder, and Insert Mode Lesson 17 Shell, Reorder, and Insert Mode Figure 17.1 Oil Sink OBJECTIVES Master the use of the Shell Tool Reorder features Insert a feature at a specific point in the design order Create a Hole Pattern

More information

Lesson 13 Patterns and Weldments

Lesson 13 Patterns and Weldments Lesson 13 Patterns and Weldments Figure 13.1 Mounting System Weldment OBJECTIVES Create directional patterns and dimensional patterns Pattern components on an assembly Insert multiple standard parts using

More information

Lesson 13 Patterns and Weldments

Lesson 13 Patterns and Weldments Lesson 13 Patterns and Weldments Figure 13.1 Mounting System Weldment OBJECTIVES Create directional patterns Create dimensional patterns Pattern components on an assembly Insert multiple standard parts

More information

Autodesk Inventor 6 Essentials Instructor Guide Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the follow

Autodesk Inventor 6 Essentials Instructor Guide Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the follow Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the following topics and provides exercises for students to practice their skills. Day Two Topic: How to create

More information

Drawing Tips ME170. Instructor: Mike Philpott (

Drawing Tips ME170. Instructor: Mike Philpott ( Drawing Tips Instructor: Mike Philpott (email: mphilpot@illinois.edu) Configuration of Creo Prepare Creo for drawing creation. - Open Creo Parametric 3.0 from the Start Menu. - Set your working directory.

More information

Solidworks 2006 Surface-modeling

Solidworks 2006 Surface-modeling Solidworks 2006 Surface-modeling (Tutorial 2-Mouse) Surface-modeling Solid-modeling A- 1 Assembly Design Design with a Master Model Surface-modeling Tutorial 2A Import 2D outline drawing into Solidworks2006

More information

Skateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line

Skateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step

More information

Skateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2

Skateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2 Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.

More information

CO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.

CO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar. CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.

More information

StickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC

StickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC StickFont Editor v1.01 User Manual Copyright 2012 NCPlot Software LLC StickFont Editor Manual Table of Contents Welcome... 1 Registering StickFont Editor... 3 Getting Started... 5 Getting Started...

More information

Swept Blend Creates a quilt using swept blend geometry.

Swept Blend Creates a quilt using swept blend geometry. Swept Blend Creates a quilt using swept blend geometry. 1 A surface can be defined by a set of cross-sections located at various points along a controlling Spine Curve. In Pro/SURFACE, this is known as

More information

Glider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.

Glider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar. Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.

More information

Modeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1

Modeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1 Modeling a Gear This tutorial describes how to create a toothed gear. It combines using wireframe, solid, and surface modeling together to create a part. The model was created in standard units. To begin,

More information

CO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.

CO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar. Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step

More information

Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation

Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation 1 Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation In Module 5, we will learn how to create a 3D folded model of a sheet metal transition

More information

Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction.

Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction. 3.1: Sculpting Sculpting in Fusion 360 allows for the intuitive freeform creation of organic solid bodies and surfaces by leveraging the T- Splines technology. In the Sculpt Workspace, you can rapidly

More information

Exercise Guide. Published: August MecSoft Corpotation

Exercise Guide. Published: August MecSoft Corpotation VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4

More information

SOLIDWORKS 2016 and Engineering Graphics

SOLIDWORKS 2016 and Engineering Graphics SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following

More information

Module 1: Basics of Solids Modeling with SolidWorks

Module 1: Basics of Solids Modeling with SolidWorks Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists

More information

Autodesk Inventor 2019 and Engineering Graphics

Autodesk Inventor 2019 and Engineering Graphics Autodesk Inventor 2019 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the

More information

SolidWorks 2013 and Engineering Graphics

SolidWorks 2013 and Engineering Graphics SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following

More information

Body. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.

Body. Chapter 2. CO2 Rail Car E. A. Save as BODY RAIL E. Step 1. Open your BLANK file. Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step

More information

Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.

Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar. Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.

More information

CATIA Electrical Space Reservation TABLE OF CONTENTS

CATIA Electrical Space Reservation TABLE OF CONTENTS TABLE OF CONTENTS Introduction...1 Manual Format...2 Electrical Reservations...3 Equipment Reservations...5 Pathway Reservations...31 Advanced Reservations...49 Reservation Analysis...67 Clash...69 Sectioning...73

More information

H Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.

H Stab and V Stab. Chapter 6. Glider. A. Open and Save as H STAB. Step 1. Open your STABILIZER BLANK file. Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch

More information

Randy H. Shih. Jack Zecher PUBLICATIONS

Randy H. Shih. Jack Zecher   PUBLICATIONS Randy H. Shih Jack Zecher PUBLICATIONS WWW.SDCACAD.COM AutoCAD LT 2000 MultiMedia Tutorial 1-1 Lesson 1 Geometric Construction Basics! " # 1-2 AutoCAD LT 2000 MultiMedia Tutorial Introduction Learning

More information

Additional Exercises. You will perform the following exercises to practice the concepts learnt in this course:

Additional Exercises. You will perform the following exercises to practice the concepts learnt in this course: Additional Exercises You will perform the following exercises to practice the concepts learnt in this course: Master Exercise : Mobile Phone Plastic Bottle Exercise 1 Master Exercise : Mobile Phone In

More information

An Introduction to Autodesk Revit Massing, Surface Divisions, and Adaptive Components

An Introduction to Autodesk Revit Massing, Surface Divisions, and Adaptive Components An Introduction to Autodesk Revit Massing, Surface Divisions, and Adaptive Components Chad Smith KarelCAD, Australia AB2463-L As the Revit massing tools become more polished and robust, users are becoming

More information

SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users

SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing

More information

SOLIDWORKS 2018 Reference Guide

SOLIDWORKS 2018 Reference Guide SOLIDWORKS 2018 Reference Guide A comprehensive reference guide with over 250 standalone tutorials David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC PUBLICATIONS Better Textbooks. Lower Prices.

More information

Chair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.

Chair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane. Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,

More information

Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1

Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1 Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.

More information

ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.

ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK. PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step

More information

Delta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.

Delta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar. Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step

More information

Lesson 1 Parametric Modeling Fundamentals

Lesson 1 Parametric Modeling Fundamentals 1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.

More information

Speedway. Body. (S) on the Sketch toolbar. Fig. 1

Speedway. Body. (S) on the Sketch toolbar. Fig. 1 Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager

More information

Module 4A: Creating the 3D Model of Right and Oblique Pyramids

Module 4A: Creating the 3D Model of Right and Oblique Pyramids Inventor (5) Module 4A: 4A- 1 Module 4A: Creating the 3D Model of Right and Oblique Pyramids In Module 4A, we will learn how to create 3D solid models of right-axis and oblique-axis pyramid (regular or

More information

Mechanical Design V5R19 Update

Mechanical Design V5R19 Update CATIA V5 Training Foils Mechanical Design V5R19 Update Version 5 Release 19 August 2008 EDU_CAT_EN_MD2_UF_V5R19 1 About this course Objectives of the course Upon completion of this course you will be able

More information

CATIA Surface Design

CATIA Surface Design CATIA V5 Training Exercises CATIA Surface Design Version 5 Release 19 September 2008 EDU_CAT_EN_GS1_FX_V5R19 Table of Contents (1/2) Creating Wireframe Geometry: Recap Exercises 4 Creating Wireframe Geometry:

More information

JSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.

JSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar. Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.

More information

Chapter 2 Parametric Modeling Fundamentals

Chapter 2 Parametric Modeling Fundamentals 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the Shape before Size Approach Use the

More information

Nose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1

Nose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1 Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step

More information

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD 3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions

More information

Piping Design. Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index

Piping Design. Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index Piping Design Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index Dassault Systèmes 1994-2001. All rights reserved. Site Map Piping Design member member

More information

SolidWorks Implementation Guides. User Interface

SolidWorks Implementation Guides. User Interface SolidWorks Implementation Guides User Interface Since most 2D CAD and SolidWorks are applications in the Microsoft Windows environment, tool buttons, toolbars, and the general appearance of the windows

More information

Parametric Modeling with. Autodesk Fusion 360. First Edition. Randy H. Shih SDC. Better Textbooks. Lower Prices.

Parametric Modeling with. Autodesk Fusion 360. First Edition. Randy H. Shih SDC. Better Textbooks. Lower Prices. Parametric Modeling with Autodesk Fusion 360 First Edition Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites

More information

Technique or Feature Where Introduced

Technique or Feature Where Introduced Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around

More information

Project curves, points, or sketches onto faces and planes.

Project curves, points, or sketches onto faces and planes. Project Curve Path: Curve tab > Derived Curve group > Project Curve Objectives Project curves, points, or sketches onto faces and planes. Prerequisites File tab > Start > Modeling Projecting Curves to

More information

CO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.

CO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.

More information

Roadway Alignments and Profiles

Roadway Alignments and Profiles NOTES Module 15 Roadway Alignments and Profiles In this module, you learn how to create horizontal alignments, surface profiles, layout (design) profiles, and profile views in AutoCAD Civil 3D. This module

More information

Equipment Support Structures

Equipment Support Structures Equipment Support Structures Overview Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform Columns Creating Plates with Openings Bracing

More information

Lesson 3: Surface Creation

Lesson 3: Surface Creation Lesson 3: Surface Creation In this lesson, you will learn how to create surfaces from wireframes. Lesson Contents: Case Study: Surface Creation Design Intent Stages in the Process Choice of Surface Sweeping

More information

Equipment Support Structures

Equipment Support Structures Page 1 Equipment Support Structures Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform

More information

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS

More information

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now

More information

Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints

Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the

More information

SOLIDWORKS 2017 Keyboard Modifiers & Shortcuts

SOLIDWORKS 2017 Keyboard Modifiers & Shortcuts SOLIDWORKS 2017 Keyboard Modifiers & Shortcuts Copy/Paste Ctrl+C and Ctrl+V These are similar in functionality to Windows. Sketches Copies and pastes sketch entities. Part Copies and pastes sketches. Assemblies

More information

Create the Through Curves surface

Create the Through Curves surface Create the Through Curves surface 1. Open ffm4_mc_fender. 2. Select all three strings, and then on the Analyze Shape toolbar, click Show End Points. Notice there are two curves in the strings on the left

More information

Publication Number spse01695

Publication Number spse01695 XpresRoute (tubing) Publication Number spse01695 XpresRoute (tubing) Publication Number spse01695 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens

More information

Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide

Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to

More information

Doctor Walt s Solid Edge Version 19 Workbook 137

Doctor Walt s Solid Edge Version 19 Workbook 137 Still using the SMART DIMENSION Tool, click on the left vertical edge of the sketch. Move the cursor to the left and click to set the text position. Type 1.5 for the value and hit the ENTER Key. Next,

More information

Beginners Guide Maya. To be used next to Learning Maya 5 Foundation. 15 juni 2005 Clara Coepijn Raoul Franker

Beginners Guide Maya. To be used next to Learning Maya 5 Foundation. 15 juni 2005 Clara Coepijn Raoul Franker Beginners Guide Maya To be used next to Learning Maya 5 Foundation 15 juni 2005 Clara Coepijn 0928283 Raoul Franker 1202596 Index Index 1 Introduction 2 The Interface 3 Main Shortcuts 4 Building a Character

More information

The Rectangular Problem

The Rectangular Problem C h a p t e r 2 The Rectangular Problem In this chapter, you will cover the following to World Class standards: The tools for simple 2D Computer Aided Drafting (CAD) The Command Line and the Tray The Line

More information

Chapter 2 Parametric Modeling Fundamentals

Chapter 2 Parametric Modeling Fundamentals 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the "Shape before Size" Approach Use

More information

CATIA V5 Parametric Surface Modeling

CATIA V5 Parametric Surface Modeling CATIA V5 Parametric Surface Modeling Version 5 Release 16 A- 1 Toolbars in A B A. Wireframe: Create 3D curves / lines/ points/ plane B. Surfaces: Create surfaces C. Operations: Join surfaces, Split & Trim

More information

User Guide. mk Config

User Guide. mk Config User Guide mk Config mk Config Register 1.1. CD-Start 4 1.2. Installation 5 1.3. Start 6 1.4. Layout of user interface and functions 7 1.4.1. Overview 7 1.4.2. Part buttons 8 1.4.3. Menus 9 1.4.3.1. Export

More information

Mastercam X6 for SolidWorks Toolpaths

Mastercam X6 for SolidWorks Toolpaths Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.

More information

Battery Holder 2 x AA

Battery Holder 2 x AA Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,

More information

Parametric Modeling. with. Autodesk Inventor Randy H. Shih. Oregon Institute of Technology SDC

Parametric Modeling. with. Autodesk Inventor Randy H. Shih. Oregon Institute of Technology SDC Parametric Modeling with Autodesk Inventor 2009 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. 2-1 Chapter

More information

AutoCAD 2009 Tutorial

AutoCAD 2009 Tutorial AutoCAD 2009 Tutorial Second Level: 3D Modeling Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. AutoCAD 2009

More information

Module 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts

Module 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts Inventor (5) Module 4B: 4B- 1 Module 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts In Module 4B, we will learn how to create

More information

Parametric Modeling with UGS NX 4

Parametric Modeling with UGS NX 4 Parametric Modeling with UGS NX 4 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric Modeling

More information

Autodesk Inventor 2018

Autodesk Inventor 2018 Learning Autodesk Inventor 2018 Modeling, Assembly and Analysis Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following

More information

Autodesk Inventor 2016 Learn by doing. Tutorial Books

Autodesk Inventor 2016 Learn by doing. Tutorial Books Autodesk Inventor 2016 Learn by doing Tutorial Books Copyright 2015 Kishore This book may not be duplicated in any way without the express written consent of the publisher, except in the form of brief

More information

Solid Modeling: Part 1

Solid Modeling: Part 1 Solid Modeling: Part 1 Basics of Revolving, Extruding, and Boolean Operations Revolving Exercise: Stepped Shaft Start AutoCAD and use the solid.dwt template file to create a new drawing. Create the top

More information

Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1

Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1 Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click

More information

Creating T-Spline Forms

Creating T-Spline Forms 1 / 28 Goals 1. Create a T-Spline Primitive Form 2. Create a T-Spline Revolve Form 3. Create a T-Spline Sweep Form 4. Create a T-Spline Loft Form 2 / 28 Instructions Step 1: Go to the Sculpt workspace

More information

USING THE TRIBALL FOR POSITIONING

USING THE TRIBALL FOR POSITIONING USING THE TRIBALL FOR POSITIONING Although many important positioning tools are available, none are as versatile as the TriBall tool. This TriBall tool offers complete repositioning of many items: Shapes

More information

create 2 new grid lines

create 2 new grid lines STEP 1: open your class-01 Project file _ go to Level 1 _ select grid line 1 _ type CO (copy) _ repeat for grid line 3 as shown in image 1 Architectural Column STEP 2: from the Ribbon under the Home tab

More information

4) Finish the spline here. To complete the spline, double click the last point or select the spline tool again.

4) Finish the spline here. To complete the spline, double click the last point or select the spline tool again. 1) Select the line tool 3) Move the cursor along the X direction (be careful to stay on the X axis alignment so that the line is perpendicular) and click for the second point of the line. Type 0.5 for

More information

Adobe Illustrator CS5 Part 2: Vector Graphic Effects

Adobe Illustrator CS5 Part 2: Vector Graphic Effects CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Adobe Illustrator CS5 Part 2: Vector Graphic Effects Summer 2011, Version 1.0 Table of Contents Introduction...2 Downloading the

More information

KEYCREATOR 3D Direct Modeling Software

KEYCREATOR 3D Direct Modeling Software KeyCreator Lesson KC5107 Graft The Graft Function is a powerful partner to the Prune Function that we used earlier. You will typically use the Graft Function immediately after performing a pruning operation

More information

Object Basics. Overview. Ellipse Command. Continued... X Commands. X System Variables

Object Basics. Overview. Ellipse Command. Continued... X Commands. X System Variables Object Basics Continued... Object Basics 1 Overview X Commands T ARC (Command) T CIRCLE (Command) T DONUT (Command) T ELLIPSE (Command) T HELIX (Command) T PLINE (Command) T SPLINE (Command) T BLEND (Command)

More information

Introduction to Autodesk Revit Structure

Introduction to Autodesk Revit Structure 11/30/2005-5:00 pm - 6:30 pm Room:N. Hemispheres (Salon E2) (Dolphin) Walt Disney World Swan and Dolphin Resort Orlando, Florida Nicolas Mangon - Autodesk SD35-1 This year, Autodesk is introducing the

More information

Publication Number spse01695

Publication Number spse01695 XpresRoute (tubing) Publication Number spse01695 XpresRoute (tubing) Publication Number spse01695 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens

More information

VERO UK TRAINING MATERIAL

VERO UK TRAINING MATERIAL VERO UK TRAINING MATERIAL VISI Basic 2-D Modelling course (V-16) VISI Modelling 2D Design Introduction Many component designs follow a similar route, beginning with a 2D design, part modelled using solids

More information

Electrical Cableway Routing

Electrical Cableway Routing Electrical Cableway Routing Preface Using This Guide What's New? Getting Started Entering the Workbench Placing a Hanger Routing a Loft Through Hangers Placing a Conduit on a Run Saving Documents Updating

More information

Parametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS

Parametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS Parametric Modeling With Autodesk Inventor R10 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric

More information

StickFont v2.12 User Manual. Copyright 2012 NCPlot Software LLC

StickFont v2.12 User Manual. Copyright 2012 NCPlot Software LLC StickFont v2.12 User Manual Copyright 2012 NCPlot Software LLC StickFont Manual Table of Contents Welcome... 1 Registering StickFont... 3 Getting Started... 5 Getting Started... 5 Adding text to your

More information

A Comprehensive Introduction to SolidWorks 2011

A Comprehensive Introduction to SolidWorks 2011 A Comprehensive Introduction to SolidWorks 2011 Godfrey Onwubolu, Ph.D. SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Chapter 2 Geometric Construction Tools Objectives: When

More information

Boat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.

Boat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point. Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on

More information

Parametric Modeling with NX 12

Parametric Modeling with NX 12 Parametric Modeling with NX 12 NEW Contains a new chapter on 3D printing Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the

More information

EXPERIMENT NO: NAME OF EXPERIMENT: -01 2D & 3D CAD modelling methodology using package AutoCAD.

EXPERIMENT NO: NAME OF EXPERIMENT: -01 2D & 3D CAD modelling methodology using package AutoCAD. SHRI SHIVAJI EDUCATION SOCIETY, AMRAVATI S, COLLEGE OF ENGINEERING & TECHNOLOGY, AKOLA Babhulgaon (JH) N.H.No.6, Akola-444104 DEPARTMENT OF MECHANICAL ENGINEERING COMPUTER SOFTWARE APPLICATIONS -I LAB.

More information

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05 Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating

More information

An Introduction to Autodesk Inventor 2010 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation

An Introduction to Autodesk Inventor 2010 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation An Introduction to Autodesk Inventor 2010 and AutoCAD 2010 Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation www.schroff.com 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded

More information

COMPUTER AIDED DESIGN CURRICULLOM RHINO BASED 3D DESIGN

COMPUTER AIDED DESIGN CURRICULLOM RHINO BASED 3D DESIGN COMPUTER AIDED DESIGN CURRICULLOM RHINO BASED 3D DESIGN S.no. CONTENTS Page no S. no. CONTENTS PAGE no. 1. Introduction 1 2. Necessary of Rhino in Designing 2 3. Working with 3D Models 3 4. Object Types

More information

Constraint Based Modeling Geometric and Dimensional. ENGR 1182 SolidWorks 03

Constraint Based Modeling Geometric and Dimensional. ENGR 1182 SolidWorks 03 Constraint Based Modeling Geometric and Dimensional ENGR 1182 SolidWorks 03 Today s Objectives Using two different type of constraints in SolidWorks: Geometric Dimensional SW03 In-Class Activity List Geometric

More information

Jewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3

Jewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3 Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in

More information

Boat. Battery Holder AA

Boat. Battery Holder AA Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click

More information