7/7/2009. Chapter 7 Object Snaps and Autotracking. Chapter 7 Learning Objectives. Object Snap. Object Snap. Object Snap
|
|
- Barrie Richard
- 6 years ago
- Views:
Transcription
1 Chapter 7 Learning Objectives Chapter 7 Object Snaps and Autotracking JULY 7, 2009 Set running object snap modes for continuous use. Use object snap overrides for single point selections. Select appropriate object snaps for various drawing tasks. Use the AutoSnap features to speed up point specifications. Use AutoTrack to locate points relative to other points in a drawing. Object Snap Object snap is a useful AutoCAD tools. It improves your drafting speed and accuracy through the concept of snapping. Object snap modes identify the object snap point. The AutoSnap feature is on by default and displays snap mode information while you draw using object snaps. Command: OS or OSnap F3 to toggle on Or icon on status bar Object Snap Object Snap 1
2 Running Object Snaps Running object snaps are on by default and may be the quickest way to use object snap. By default, the Endpoint, Center, Intersection, and Extension running object snap modes are active. The quickest way to activate or deactivate running object snap modes is to right-click on the Object Snap or Object Snap Tracking button on the status bar to display the shortcut menu. Then select the running object snaps you want to turn on or off. F11 will toggle object snap tracking on and off You can also set running object snap modes using the Object Snap tab in the Drafting Settings dialog box. Running Object Snap You can also set running object snap modes using the Object Snap tab in the Drafting Settings dialog box. The Drafting Settings dialog box can be displayed from the keyboard or the menu browser or by rightclicking on any of the status bar toggle buttons and selecting the Settings menu option. The Drafting Settings dialog box can also be accessed by typing Dsettings, SE or DS at the command prompt DSettings Object Snap Override Enter an object snap override when you are prompted to select a point and the active running object snaps are conflicting with each other, or the desired snap is not running. Object snap overrides allow you to pick a location on an existing object that corresponds only to the selected object snap mode. After you select the point, the running object snap modes are reactivated Object Snap Override Object Snap Override After you access a tool, the preferred technique for activating an object snap override is to use the Object Snap shortcut menu. To use this method, press and hold the [Shift] key and then right-click to display the shortcut menu. It may also be accessed by right clicking on the object snap icon on the status bar. Ri ht Cli k Right Click to access Object Snap Override 2
3 Lab Activity Type OS to access Object snap settings Check End point, Mid point, and Intersection Create rectangle Use Extension osnap override to create another rectangle adjacent and inline with the previously created rectangle Temporary Track Point Snap Using temporary track point is similar to using the extension object snap mode. The main difference is that with temporary track point, you actually pick points of reference, instead of acquiring points as with the extension object snap mode. Example: temporary tracking can be used to place a circle at the center of a rectangle. Though not necessary, temporary track points are usually selected using running object snaps or object snap overrides. Lab Activity- Temporary Tracking Snap From Create a rectangle Use temporary tracking to locate the midpoint of one of the vertical lines, and the midpoint of one of the horizontal lines. The point where these two lines cross will be the center. Create a circle using this center. The From point object snap allows you to locate a point from a specified reference base point using a coordinate entry technique such as relative coordinate, polar coordinate, or direct distance entry. To use Snap from simply enter the coordinates relative to the snap point. Snap From Example: A circle may be created a given distance away from the midpoint of this line Object Snap Tracking Object snap tracking has two requirements: running object snaps must be active and the crosshairs must pause over the selected point long enough to acquire the point. Object snap tracking mode is only available for points selected by the currently active object snap modes. When running object snaps are active, all selected object snap modes are available for object snap tracking. 3
4 Object Snap Tracking To enable object snap tracking, pick the Object Snap Tracking button on the status bar, or press the [F11] function key, or use the Object Snap Tracking On (F11) check box in the Object Snap tab of the Drafting Settings dialog box. Polar Tracking Click the icon on the status bar, or press the [F10] function key, or use the Polar Tracking On (F10) check box in the Polar Tracking tab of the Drafting Settings dialog box to toggle polar tracking on and off. Polar Tracking When polar tracking mode is turned on, the crosshairs snaps to preset incremental angles, if a point is being located relative to another point Polar tracking vectors are displayed as dotted lines whenever the crosshairs aligns with any of these preset angles. To set incremental angles, use the Polar Tracking tab in the Drafting Settings dialog box. The Drafting Settings dialog box can be displayed by rightclicking on any of the status bar toggle buttons and selecting the Settings option, or typing DS, Dsettings or SE The Polar Angle Settings area sets the desired polar angle increments. Use the Increment angle drop-down list to select the angle increments at which polar tracking vectors occur. The preset angle increments available in the Polar Angle Settings area of the Drafting Settings dialog box are also available in the shortcut menu displayed when you right-click on the Polar Tracking button on the status bar. Polar Tracking Polar Tracking Polar Tracking Custom Angles You can define specific polar tracking angles by picking the New button in the Polar Angle Settings area. Type a new angle value in the text box that appears in the Additional angles window. Pick the New button each time you want to add another angle. Additional i angles are used together with the increment angle setting when you use polar tracking. Only the specific additional angle you enter is recognized, not each increment of the angle. Use the Delete button to remove angles from the list. Make the additional angle(s) inactive by unchecking the Additional angles check box. You can define specific polar tracking angles by picking the New button in the Polar Angle Settings area. Type a new angle value in the text box that appears in the Additional angles window. Up to 10 additional angles may be added Click NEW to add additional angle increments 4
5 Polar Tracking Absolute versus Relative Polar Tracking Absolute versus Relative The Polar Angle measurement setting determines whether the polar snap increments are constant or relative to the previous segment. If Absolute is selected, the polar snap angles are measured from the base angle of 0 set for the drawing. If Relative to last segment is selected, each increment angle is measured from a base angle established by the previously drawn segment. Lab Activity Draw a Line that is 45 degrees above the horizontal. Create a new polar tracking increment of 12 degrees Set the polar tracking measurement setting to relative. Create a line from the end of the newly created 45 degree inclined line. Observe how the angleis measured. Change the angular measurement to absolute and create another line from the end of the inclined line and observe how the polar tracking angle is measured Polar Tracking with Polar Snaps Polar tracking can also me used with polar snaps and predetermined length increment. The desired angle and length increments are established in the Snap and Grid tab of the Drafting Settings dialog box. Access grid/ snap settings by right clicking on grid icon. Enable polar snap, set polar snap, snap x and y intervals to.5000 Create a pattern similar to the one at right using snap mode and.500 inch segments Lab Activity Polar Tracking with Polar Snaps To activate polar snap, pick the PolarSnap button in the Snap type & style area of the dialog box. Picking this button activates the Polar spacing area and deactivates the Snap area. The length of the polar snap increment is set in the Polar distance: box. If the Polar distance: setting is 0, the polar snap distance will be the orthogonal snap distance Note Polar tracking may not be used when in ortho mode. 5
6 Lab Assignment Chapter 8 Construction Tools and Multiview Drawings Drawing Problems, pages , 7-1, 7-2,7-4, and 7-9 Use the OFFSET tool to draw parallel lines and curves. Mark points on objects at equal lengths using the DIVIDE tool. Set designated increments on an existing object using the MEASURE tool. Create construction lines using the XLINE and RAY tools. Create orthographic multiview drawings and auxiliary views. Offset Tool Command: Offset or O The OFFSET tool is one of the most common geometric construction tools. Use the OFFSET tool to form parallel lines and polylines. For example, existing lines or polylines can be offset to construct the thickness of architectural floor plan walls. Existing circles, arcs, and curves can be offset to form concentric objects. Offset Tool The best way to use the OFFSET tool is to enter an offset value at the Specify offset distance or Through/Erase/Layer] <current>: prompt. The last offset distance used, is the default and is shown in brackets. For example, if you want to draw two parallel circles a distance of.1 unit apart, access the OFFSET tool, and at the Specify offset distance or [Through/Erase/Layer] <current>: prompt, enter a value of.1. Pick the circle you want to offset, and then pick the side of the circle on which the offset occurs Offset Tool Once the OFFSET tool has been used it remains active, allowing you to pick another object to offset using the same offset distance. When you are finished using the tool, press the [Enter] key, the [Esc] key or the space bar, or choose the Exit option. If you do not know the offset value, but two reference points exist in the drawing area, you can pick a first point and then a second point instead of typing an offset value. Offsetting - Erasing the Original Object When you offset an object, you may want to remove the original object. Instead of offsetting the object and then erasing the source object, you can use the Erase option of the OFFSET tool to erase the source object. Initiate the OFFSET tool, enter the Erase option, and choose Yes at the Erase source object after offsetting? Prompt to erase the source object. The Yes option remains as the default until it is changed to No. Be sure to change this option back to No if you do not want the source offset object 6
7 Offsetting - Erasing the Original Object Enter E to erase the source object Changing the Layer of the Offset Object The Layer option of the OFFSET tool allows you to place the offset object on the current layer. For example, if the offset source object is on the Electrical layer and the offset object needs to be placed on the Lighting layer, this can be done during the offset operation if Lighting is the current layer. After initiating the OFFSET tool, enter the Layer option and choose Current at the Enter layer option for offset objects prompt to create the offset object on the current layer. The Current option remains the default until it is changed to Source Changing the Layer of the Offset Object Offsetting Multiple Times Type L to put offset object on current layer and enter c for current and s for source After the object to offset has been selected, the Multiple option can be used to offset an object more than once with the same distance between the objects without reselecting the object to offset. Initiate the OFFSET tool, specify the offset distance, and pick the source object. You can then select the Multiple option and begin picking to specify the offset direction. Point Tool Points are useful for identifying specific locations on a drawing and for marking positions on objects. You can draw points anywhere on the screen using the POINT tool. Once you access the POINT tool, you can pick or type coordinates to place points. The POINT tool has two variations: Single Point and Multiple Points. Command: Point or PO The point style may be selected from 20 different styles. Command: DDPTYPE Point Tool 7
8 Point Tool Points are useful for identifying specific locations on a drawing and for marking positions on objects. You can draw points anywhere on the screen using the POINT tool. Once you access the POINT tool, you can pick or type coordinates to place points. The POINT tool has two variations: Single Point and Multiple Points. To place a single point object and then exit the POINT tool, access the POINT tool using keyboard entry or select the Single Point option from the Point menu in the menu browser. To draw multiple points without exiting the POINT tool, use the Multiple Points button on the ribbon or the Multiple Point option from the Point submenu 8
Object Snap. Sacramento City College Engineering Design Technology. Object Snap 1
Object Snap Sacramento City College Engineering Design Technology Object Snap 1 Objectives Use OSNAP to create precision drawings Use object snap overrides for single point selections Set running object
More informationby Paul Richard and Jim Fitzgerald
Chapter 5 - Drawing Tools and Drafting Settings by Paul Richard and Jim Fitzgerald Richard / Fitzgerald :INTRODUCTION TO AutoCAD 2012 Copyright 2012 Pearson Education, Upper Saddle River, NJ 07458. All
More informationExcerpt from "Inside CorelCAD" - Windows edition To purchase the full book, please go to
chapter 3 CAD Concepts 37 1. Start any drawing command, such as Line. : line Specify start point» (Move cursor.) 2. Right-click the coordinate field. Notice the short cut menu. 3. Choose Relative. (The
More information7/21/2009. Chapters Learning Objectives. Fillet Tool
Chapters 12-13 JULY 21, 2009 Learning Objectives Chapter 12 Chapter 13 Use the FILLET tool to draw fillets, rounds, and other rounded corners. Place chamfers and angled corners with the CHAMFER tool. Separate
More informationThe Rectangular Problem
C h a p t e r 2 The Rectangular Problem In this chapter, you will cover the following to World Class standards: The tools for simple 2D Computer Aided Drafting (CAD) The Command Line and the Tray The Line
More informationTutorial 3: Constructive Editing (2D-CAD)
(2D-CAD) The editing done up to now is not much different from the normal drawing board techniques. This section deals with commands to copy items we have already drawn, to move them and to make multiple
More informationAfter completing this lesson, you will be able to:
LEARNING OBJECTIVES After completing this lesson, you will be able to: 1. Create a template. 2. Understand the AutoCAD Window. 3. Understand the use of the function keys. 4. Select commands using the Pull-down
More informationAfter completing this lesson, you will be able to:
LEARNING OBJECTIVES After completing this lesson, you will be able to: 1. Create a template. 2. Understand the AutoCAD Window. 3. Understand the use of the function keys. 4. Select commands using the Pull-down
More information7/14/2009. Chapters Autocad Multi Line Text Tools. Multi Line Text Tool Ribbon. Multi Line Text Tool. July 14, 2009
Chapters 9-11 July 14, 2009 Chapter 9 Learning Objectives Describe and use proper text standards. Calculate drawing scale and text height. Develop and use text styles. Make multiple lines of text with
More informationSetting Up Your Drawing Environment
Setting Up Your Drawing Environment In This Chapter 3 After you start a drawing, you can change its settings, including drawing units and limits, snap and grid settings, and layer, linetype, and lettering
More informationUsing Coordinate Systems
Using Coordinate Systems In This Chapter 5 As you draw you use the coordinate system to specify points in the drawing. You can locate and use your own movable user coordinate system (UCS) for working on
More informationNever Digitize Again! Converting Paper Drawings to Vector
December 2-5, 2003 MGM Grand Hotel Las Vegas Never Digitize Again! Converting Paper Drawings to Vector Felicia Provencal GD42-3L How many hours have you spent hunched over a digitizing board converting
More informationRandy H. Shih. Jack Zecher PUBLICATIONS
Randy H. Shih Jack Zecher PUBLICATIONS WWW.SDCACAD.COM AutoCAD LT 2000 MultiMedia Tutorial 1-1 Lesson 1 Geometric Construction Basics! " # 1-2 AutoCAD LT 2000 MultiMedia Tutorial Introduction Learning
More informationThe Department of Construction Management and Civil Engineering Technology CMCE-1110 Construction Drawings 1 Lecture Introduction to AutoCAD What is
The Department of Construction Management and Civil Engineering Technology CMCE-1110 Construction Drawings 1 Lecture Introduction to AutoCAD What is AutoCAD? The term CAD (Computer Aided Design /Drafting)
More informationStickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC
StickFont Editor v1.01 User Manual Copyright 2012 NCPlot Software LLC StickFont Editor Manual Table of Contents Welcome... 1 Registering StickFont Editor... 3 Getting Started... 5 Getting Started...
More informationRebarCAD Usage Hints and Tips
RebarCAD Usage Hints and Tips Hints & Tips the Change Bar Style Command A drawing can have a combination of bar styles and bars can be changed from one style to another using the Change Bar Style command.
More informationInstructor: Dr.Ashok Kaushal
Continuing Education Department AutoCAD Instructor: Dr.Ashok Kaushal E-mail: ashok_kaushal@hotmail.com Topics Intro to CAD, Geometric commands, Absolute & Relative values, Line, Circle, Arc Dr. Ashok Kaushal
More informationModule: Computer Aid Design
Module: Computer Aid Design Lesson 1: Introduction to AutoCAD 2010 & Drafting Commands 1. AUTOCAD OVERVIEW CAD= Computer Aided Design, (1982) 1.1 User Interface: 1.2 Info Center Page 1 of 14 1.3 Zoom 1.3
More informationGrips - Automatic Editing
Grips - Automatic Editing Sacramento City College Engineering Design Technology Grips - Automatic Editing 1 Objectives Use grips to do automatic editing with the STRETCH, COPY, MOVE, ROTATE, SCALE and
More informationGetting Started. In This Chapter
Getting Started In This Chapter 2 This chapter introduces concepts and procedures that help you get started with AutoCAD. You learn how to open, close, and manage your drawings. You also learn about the
More informationTutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
More informationControlling the Drawing Display
Controlling the Drawing Display In This Chapter 8 AutoCAD provides many ways to display views of your drawing. As you edit your drawing, you can control the drawing display and move quickly to different
More informationUsing Object Snap to Draw a Rug Design
Using Object Snap to Draw a Rug Design The objective of the rest of this tutorial is to learn the use of object snap and hatch. Because AutoCAD is based on vectors and coordinate geometry, it can easily
More informationGEO 154 CARTOGRAPHY II- PLOTTING USING AUTOCAD- ASSIGMENT HELP
GEO 154 CARTOGRAPHY II- PLOTTING USING AUTOCAD- ASSIGMENT HELP DOCUMENT. For one to two reasons data may not be in a format that can be integrated into AutoCAD software, but coordinates may be separated
More information6/23/2009. AutoCAD Chapter 3 Objectives. Line Command. Coordinate Entry Methods. Rectangular Coordinate System
Chapter 3 Objectives AutoCAD 2009 CHAPTER 3 JUNE 23, 2009 Use the correct entry format when entering numbers Demonstrate how to end or cancel commands Describe and use several point entry methods Draw
More informationLesson 1 CAD Mechanical Part 1 Beginning Drawing Objectives
Lesson 1 CAD Mechanical Part 1 Beginning Drawing Objectives In this assignment you will learn to identify important terminology and functions of AutoCAD, to begin a new drawing and save data in the proper
More informationDFTG 1309 Instructor I. Zhebrak. Class Single line text - Creating text styles - Justification - Insert symbols
DFTG 1309 Instructor I. Zhebrak Class 17 LECTURE: - Single line text - Creating text styles - Justification - Insert symbols GRADED EXERCISES: - Draw Surveyor Plan using Spline and Line commands. Calculate
More informationExercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
More informationMET 107 Drawing Tool (Shapes) Notes Day 3
MET 107 Drawing Tool (Shapes) Notes Day 3 Shapes: (Insert Tab Shapes) Example: Select on the rounded rectangle Then use the mouse to position the upper left corner and produce the size by dragging out
More informationAutoCADD Tutorial A survival guide
AutoCADD Tutorial A survival guide Avery S.H. Copeland Prepared for IMDL Lab students and MIL volunteers October 9, 1997 Revised April 17, 1998 AutoCADD Tutorial Page 2 Contents Introduction Relative Coordinates
More informationRevit Architecture 2015 Basics
Revit Architecture 2015 Basics From the Ground Up Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
More information1 st Subject: AutoCAD 2000 Interface ABC: Methods of Command Entry, Open/Exit, Save Files
Intermediate Engineering Graphics 4 th Week Lecture Notes Instructor: Edward N. Locke Topic: Review of AutoCAD 2000 Interface, Settings, Options, and Tools 1 st Subject: AutoCAD 2000 Interface ABC: Methods
More informationControl the Workplane
Control the Workplane This tutorial outlines the procedures to understand and control the user coordinate system (UCS). You can realign and reorient the UCS to create and modify 3D objects on 2D workplanes
More informationIntroduction to AutoCAD 2010
Introduction to AutoCAD 2010 Alf Yarwood Chapter 3 Exercise 1 1. Open AutoCAD 2010 with a double-click on its shortcut icon in the Windows desktop. 2. Call the Line tool with a left-click on its tool icon
More informationChapter 4. Part 1 AutoCAD Basics
Chapter 4. Part 1 AutoCAD Basics Chapter Objectives Describe the AutoCAD screen layout. Perform an AutoCAD drawing setup, including setting units, limits, layers, linetypes, and lineweights. Explain the
More informationIntroduction to AutoCAD 2010
Page 1 Introduction to AutoCAD 2010 Alf Yarwood Chapter 2 Exercise 1 1. Open AutoCAD 2010 - either with a double-click on its start-up icon in the Windows desktop, or by using the method on the computer
More informationPerform editing operations such as erase, move, and trim on the objects in a drawing.
Modifying Perform editing operations such as erase, move, and trim on the objects in a drawing. The most common of these tools are located on the Modify panel of the Home tab. Take a minute to look through
More information3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.
3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats
More informationW- W. Lesson 9 Auxiliary Views and Editing with GRIPS
AutoCAD 2015 Tutorial: 2D Fundamentals 9-1 Lesson 9 Auxiliary Views and Editing with GRIPS W- W Use 2D Projection Method to Draw Auxiliary Views Create Rectangles Use the Basic GRIPS Editing Commands Create
More informationQUICK-START TUTORIALS
PUERMC02_0132276593.QXD 08/09/2006 06:05 PM Page 83 QUICK-START TUTORIALS Chapter Objectives Create two real 3D modeling projects, starting them from scratch. Know the difference between representing 3D
More informationBasic Modeling 1 Tekla Structures 12.0 Basic Training September 19, 2006
Tekla Structures 12.0 Basic Training September 19, 2006 Copyright 2006 Tekla Corporation Contents Contents 3 1 5 1.1 Start Tekla Structures 6 1.2 Create a New Model BasicModel1 7 1.3 Create Grids 10 1.4
More informationINTRODUCTION... 1 DOCUMENT CONVENTIONS... 1
INTRODUCTION... 1 DOCUMENT CONVENTIONS... 1 BEGINNING AUTOCAD... 2 USING THE START BUTTON TO LAUNCH AUTOCAD... 2 USING A SHORTCUT TO LAUNCH AUTOCAD... 2 AUTOCAD USER INTERFACE... 3 CHOOSING COMMANDS...
More informationModule 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation
1 Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation In Module 5, we will learn how to create a 3D folded model of a sheet metal transition
More informationPart Two Development of Single Solids - The Five Plutonic Solids
1 Part Two Development of Single Solids - The Five Plutonic Solids We will now proceed to learn different topics of descriptive geometry using AutoCAD 2D tools and settings. Throughout this and subsequent
More informationChapter 1. Getting Started with AutoCAD
Chapter 1 Getting Started with AutoCAD 3 4 AutoCAD 2002: The Complete Reference This chapter takes you on a tour of AutoCAD and provides an overview of the different components of the AutoCAD screen. It
More informationElise Moss Revit Architecture 2017 Basics From the Ground Up SDC. Better Textbooks. Lower Prices.
Elise Moss Revit Architecture 2017 Basics From the Ground Up SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
More informationIntroduction to AutoCAD 2012
Page 1 Introduction to AutoCAD 2012 Alf Yarwood Chapter 6 Exercise 1 1. Open AutoCAD 2012 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso.dwt. 3. Make sure
More informationCHAPTER 1 COPYRIGHTED MATERIAL. Getting to Know AutoCAD. Opening a new drawing. Getting familiar with the AutoCAD and AutoCAD LT Graphics windows
CHAPTER 1 Getting to Know AutoCAD Opening a new drawing Getting familiar with the AutoCAD and AutoCAD LT Graphics windows Modifying the display Displaying and arranging toolbars COPYRIGHTED MATERIAL 2
More informationWhen dragging out a marquee: Shift toggles the corner selection
VECTORSCRIBE DYNAMIC CORNERS When dragging out a marquee: Esc cancels the marquee When dragging out a marquee: Shift toggles the corner selection When dragging out a marquee: Option+Alt adds corners to
More informationGstarCAD Complete Features Guide
GstarCAD 2017 Complete Features Guide Table of Contents Core Performance Improvement... 3 Block Data Sharing Process... 3 Hatch Boundary Search Improvement... 4 New and Enhanced Functionalities... 5 Table...
More informationS206E Lecture 3, 5/15/2017, Rhino 2D drawing an overview
Copyright 2017, Chiu-Shui Chan. All Rights Reserved. S206E057 Spring 2017 Rhino 2D drawing is very much the same as it is developed in AutoCAD. There are a lot of similarities in interface and in executing
More informationBlocks reduce drawing size since multiple instances of a block are stored in one definition.
AGENDA: 1. Blocks and Controlling Block Properties 2. Creating and Inserting Blocks 3. Editing Blocks after Insertion 4. Storing Blocks Blocks A block is a collection of entities, grouped together and
More informationRoadway Alignments and Profiles
NOTES Module 15 Roadway Alignments and Profiles In this module, you learn how to create horizontal alignments, surface profiles, layout (design) profiles, and profile views in AutoCAD Civil 3D. This module
More informationSchematic Editing Essentials
Summary Application Note AP0109 (v2.0) March 24, 2005 This application note looks at the placement and editing of schematic objects in Altium Designer. This application note provides a general overview
More informationParametric Modeling with. Autodesk Fusion 360. First Edition. Randy H. Shih SDC. Better Textbooks. Lower Prices.
Parametric Modeling with Autodesk Fusion 360 First Edition Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
More informationAutoCAD 2013 Tutorial - Second Level: 3D Modeling
AutoCAD 2013 Tutorial - Second Level: 3D Modeling Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to
More informationLesson 5: Board Design Files
5 Lesson 5: Board Design Files Learning Objectives In this lesson you will: Use the Mechanical Symbol Editor to create a mechanical board symbol Use the PCB Design Editor to create a master board design
More informationModule 4A: Creating the 3D Model of Right and Oblique Pyramids
Inventor (5) Module 4A: 4A- 1 Module 4A: Creating the 3D Model of Right and Oblique Pyramids In Module 4A, we will learn how to create 3D solid models of right-axis and oblique-axis pyramid (regular or
More informationVisual 2012 Help Index
Visual 2012 Help Index Absolute Coordinates 2.1 Cartesian Coordinates Aim 7.4.3 Place and Aim Luminaires 7.4.4 Reaiming Luminaires Align Cursor and Plane to Current View 9.6 Align to View Align Cursor
More informationCustomizing Interface Elements and Commands Part 02
Customizing Interface Elements and Commands Part 02 Sacramento City College Engineering Design Technology Customizing Interface Elements and Commands 1 Creating New Commands Customizing Interface Elements
More informationAcknowledgement INTRODUCTION
Submitted by: 1 Acknowledgement INTRODUCTION Computers are increasingly being used for doing engineering drawings and graphics work because computers allow the graphics designer or the draughtsman to change
More informationAutoCAD 2009 Tutorial
AutoCAD 2009 Tutorial Second Level: 3D Modeling Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. AutoCAD 2009
More informationRoof Designer USER S GUIDE
Roof Designer USER S GUIDE Roof Designer-1 Roof Designer-2 Roof Designer The Roof Designer makes it easy to define and place custom roofs in your project. You can start the Roof Designer independently,
More informationLayout Tutorial. Getting Started. Creating a Layout Template
Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating a Layout Template
More informationI. Getting started in ARCHLine.XP
I. Getting started in 1 Introduction 3 1. Introduction 1.1. Definition ARCHLine.XP is a Building Information Modeller, which supports the creation of planning- and implementation documentation, tender
More informationModule 1B: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of A Truncated Right Prism
Inventor (5) Module 1B: 1B- 1 Module 1B: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of A Truncated Right Prism In this Module, we will learn how to create
More informationTips and tricks. AutoCAD 2010
Tips and tricks AutoCAD 2010 Parametric Drawing Powerful new parametric drawing functionality in AutoCAD 2010 enables you to dramatically increase productivity by constraining drawing objects based on
More informationHeads Up Design: Focusing on the drawing area
Autodesk AutoCAD 2006 New Features By Ellen Finkelstein Here are some of my favorite new features. If you want a detailed description and applicable exercises, you'll find them in my book -- AutoCAD 2006
More informationUNIT OBJECTIVES OVERVIEW INTRODUCTION OUTLINE WORKING WITH GRIPS
11 UNIT EDITING WITH GRIPS """""""'-_ ===""""~.~~~..Ii. l! 11 OVERVIEW Editing a drawing is a common practice when using AutoCAD. Moving, copying, and rotating objects are just some of the editing functions
More informationText Express Tools. Arc-Aligned Text
AutoCAD and Its Applications BASICS Chapter 10 Text The Text panel of the ribbon tab includes additional text commands. This document explains the most useful express tools for specific text applications.
More informationTutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
More information1Anchors - Access. Part 23-1 Copyright 2004 ARCHIdigm. Architectural Desktop Development Guide PART 23 ANCHORS 1-23 ANCHORS
Architectural Desktop 2005 - Development Guide PART 23 ANCHORS Contents: Anchors - Access ---- Working with the Curve Anchor ---- Working with the Leader Anchor ---- Working with the Node Anchor ---- Working
More informationSOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationGrading and Volumes CHAPTER INTRODUCTION OBJECTIVES
CHAPTER 10 Grading and Volumes INTRODUCTION AutoCAD Civil 3D uses surface breaklines, cogo points, contours, feature lines, and grading objects to create a surface design. There are numerous ways to grade
More informationNote: To open the new drawing, check the Open new drawing check box.
Table of Contents Space Allocation Drawings.................................. 3 Set Up Space Allocation Groups.............................. 3 Checking In/Out and Pinning Space Allocations..................
More informationGoogle SketchUp. and SketchUp Pro 7. The book you need to succeed! CD-ROM Included! Kelly L. Murdock. Master SketchUp Pro 7 s tools and features
CD-ROM Included! Free version of Google SketchUp 7 Trial version of Google SketchUp Pro 7 Chapter example files from the book Kelly L. Murdock Google SketchUp and SketchUp Pro 7 Master SketchUp Pro 7 s
More informationEDUCATIONAL REND LAKE COLLEGE CAD INTRODUCTION TO COMPUTER-AIDED DRAFTING DWG#10 - IN-CLASS 3D ACTIVITY REVISED: FALL 2010
INSTRUCTOR: THOMAS ARPASI REND LAKE COLLEGE CAD 1201-51 INTRODUCTION TO COMPUTER-AIDED DRAFTING DWG#10 - IN-CLASS 3D ACTIVITY 1 CAD 1201-51 Drawing 10 - In-Class 3D Modeling Goal: Quickly model a chess
More informationAutodesk Inventor 2019 and Engineering Graphics
Autodesk Inventor 2019 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the
More informationLesson 5 Solid Modeling - Constructive Solid Geometry
AutoCAD 2000i Tutorial 5-1 Lesson 5 Solid Modeling - Constructive Solid Geometry Understand the Constructive Solid Geometry Concept. Create a Binary Tree. Understand the basic Boolean Operations. Create
More informationLABORATORY 4: TO CONSTRUCT CAD MULTIPLE VIEWS I AND II
LABORATORY 4: TO CONSTRUCT CAD MULTIPLE VIEWS I AND II OBJECTIVES: After completing this session, you should be able to: 1. Use the User Coordinate System 2. Convert a solid model to a multiview using
More informationPanasonic VRF Software. New features of VRF software
Panasonic VRF Software New features of VRF software April 2013 1 Contents: Mounting scheme... 5 1. Import building scheme into software... 5 1.1. Export building scheme as DXF from AutoCAD... 5 1.2. Export
More informationQuickTutor. An Introductory SilverScreen Modeling Tutorial. Solid Modeler
QuickTutor An Introductory SilverScreen Modeling Tutorial Solid Modeler TM Copyright Copyright 2005 by Schroff Development Corporation, Shawnee-Mission, Kansas, United States of America. All rights reserved.
More informationGoogle LayOut 2 Help. Contents
Contents Contents... 1 Welcome to LayOut... 9 What's New in this Release?... 10 Learning LayOut... 12 Technical Support... 14 Welcome to the LayOut Getting Started Guide... 15 Introduction to the LayOut
More informationArch 226 CAD in Practice Fall 2011 Class-06 Rhino. [Starting Rhino] Viewports Command Line Prompts, Options Status Bar Toolbars
[Starting ] Viewports Command Line Prompts, Options Status Bar Toolbars [Understanding Views] Zoom, Pan, and Rotate the View Mouse Wheel Zoom Right Mouse Button Pan, Rotate, and Zoom Pan- shift/right click,
More informationBoA Tools Page 1 / 31
BoA Tools Page 1 / 31 Standard tools Overview 2 Work pane 3 3D-2D file Main palette 6 Layout Main Palette 9 Navigation tools 11 Workplane Palette 14 Cursor Palette 21 Numeric control 24 Selection by Criteria
More informationChapter 2 Parametric Modeling Fundamentals
2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the Shape before Size Approach Use the
More informationGetting Started with
Chapter 2 Getting Started with Learning Objectives Revit Architecture After completing this chapter, you will be able to: Start a new project. Set units of various measurement parameters for a project.
More informationResidential Design Using Autodesk Revit 2019
Daniel John Stine AIA, CSI, CDT Residential Design Using Autodesk Revit 2019 Includes video instruction SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com ACCESS CODE UNIQUE CODE
More informationApex Sketch v7. Define First
Apex Sketch v7 Legacy Draw First Drawing Method Define First Apex Sketch Version 7 Define First Apex Sketch Version 7 uses the same keystrokes as you would use traditionally in any other Apex program.
More informationAutoCAD 2009 Configuration for MUS
AutoCAD 2009 Configuration for MUS NOTE: The following steps do not apply to AutoCAD 2006 or earlier versions. These steps must be done before attempting to use MicroScribe Utility Software (MUS) with
More informationAn Introduction to Autodesk Inventor 2012 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation
An Introduction to Autodesk Inventor 2012 and AutoCAD 2012 Randy H. Shih SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Visit the following websites to learn more about this book:
More information604 - Drafting in Solid Edge: A Hands-on Experience
4 th Generation VLC courtesy of Edison2 604 - Drafting in Solid Edge: A Hands-on Experience Steve Webb, Solid Edge Field Support, #SEU13 Agenda: 604 - Drafting in Solid Edge: A Hands-on Experience Who
More informationcreate 2 new grid lines
STEP 1: open your class-01 Project file _ go to Level 1 _ select grid line 1 _ type CO (copy) _ repeat for grid line 3 as shown in image 1 Architectural Column STEP 2: from the Ribbon under the Home tab
More informationResidential Design Using Autodesk Revit Architecture 2010
Residential Design Using Autodesk Revit Architecture 2010 Introduction to Revit Hand Sketching Video Instruction rendering kitchen sketching Daniel John Stine INSIDE: MultiMedia DVD SDC PUBLICATIONS Schroff
More informationLayout Tutorial. Getting Started. Creating a Layout Template
Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating a Layout Template
More informationsolidthinking Inspired Tutorials 2009 solidthinking, Inc. for Mac
solidthinking Inspired Tutorials 2009 solidthinking, Inc. for Mac Table of Contents Quick Start Tutorials 3 Tutorial 11: Simple... Bridge 4 Tutorial 22: Desk... 12 Tutorial 33: Bookcase... 35 2 1 Quick
More informationEZ-Mill EXPRESS TUTORIAL 2. Release 13.0
E-Mill EPRESS TUTORIAL 2 Release 13.0 Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to ECAM Solutions, Inc. It is made available
More informationLesson 1 Parametric Modeling Fundamentals
1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.
More informationAn Introduction to Autodesk Inventor 2013 and AutoCAD
An Introduction to Autodesk Inventor 2013 and AutoCAD 2013 Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites
More informationAlignments CHAPTER INTRODUCTION OBJECTIVES
CHAPTER 5 Alignments INTRODUCTION This and the next four chapters focus on roadway design and its documentation. This chapter concentrates on roadway plan design. The next three chapters focus on the roadway
More information