3-AXIS GIMBAL VARI-FOCAL INDOOR DOME CAMERA

Size: px

Start display at page:

Download "3-AXIS GIMBAL VARI-FOCAL INDOOR DOME CAMERA"

Garey Carr
6 years ago
Views:

1 3-AXIS GIMBAL VARI-FOCAL INDOOR DOME CAMERA

2 Contents Features 3 Specifications 4 Dimension 5 Part Name and Descriptions 6 Base Installations 7 Connection 8 3-Axis Gimbal Adjustments 9 How to Open the Gimbal Cover Vari-focal, DC Auto Iris Lens Adjustments 9 10 OSD Menu Instructions 11 2

3 Features 1/3 CCD 550 TV Lines 3.8~9.5mm DC Auto Iris Lens 0.1 Lux(Normal), Lux(DSS On) Separate Camera Control Board -OSD Menu -Service Monitor Output 12VDC/24VAC Dual Voltage 4 Polycarbonate Bubble 3-Axis Gimbal Flush Mount Housing w/ Surface Mount Plate in single package Aluminum Mounting Accessories (Option) Compact size 3

4 Specifications Description Video Formats Image Sensor Sync System Scanning system Electronic Shutter Main Video Output Service Monitor Output Horizontal Resolution Min. Illumination S/N Ratio Lens (DC Auto Iris) Auto Iris Control Camera Control & Setup Operating Temperature Operating Humidity Power Consumption Power Requirement NTSC Indoor Dome Camera 1/3" CCD Internal * Must use specified and regulated 12VDC/24VAC power supply. * Specifications are subject to change without any prior notice. PAL 525 Lines, Interlaced 625 Lines, Interlaced 1/60 ~ 1/100,000 1/50 ~ 1/100, Vp-p Composite, 75 ohm 1.0 Vp-p Composite, 75 ohm 550 TV Lines 0.1 Lux(Color), Lux(DSS On) More than 50dB(AGC Off) Vari-focal: 3.8~9.5mm DC Level Button OSD Menu -5ºC ~ +45ºC Within 90% RH 500mA 12VDC/24VAC Dual Voltage 4

5 Dimension (Unit:mm)

6 Parts Name and Descriptions Lens 2. Power Input Connector 12VDC/24VAC Dual Voltage 3. Video Output Connector BNC 4. Service Monitor Output Connector 5. Camera Control Board Safety Wire 7. Bubble 8. Dome Cover Ring 9. Flush Mount Base 10. Surface Mount Plate Assembly Screw (Torx M4x9) 12. Assembly Screws (Philips M4x10) Mounting Screws (Philips ST4x30) 7 11 Caution : Do not aim the camera directly into the sun. 6

7 Base Installations 1. Remove dome cover by loosening 3 screws (Torx M4x9). Use Torx wrench provided with the package. 2. Surface Mount: Using four ST4x30 screws, mount surface plate to a sturdy surface. Using four M4x10screws, affix flush mount base to surface plate. (For flush mount application, disregard this step) 3. Flush Mount Using four ST4x30 screws, affix flush mount base to a sturdy surface. 1 2 Torx M4x9 Surface Mount Plastic Dowels A 3 Flush Mount A' ST4x30 M4x10 ST4x30 7

8 Connection 12VDC/24VAC CCTV Monitor LEFT DOWN UP RIGHT Service Monitor Output 20cm Service Monitor - Power connections: Requires 12VDC or 24VAC. - This camera is supplied with a second video output on the camera module. Use this feature along with a service monitor. 8

9 3-Axis Gimbal Adjustments The Gimbal mechanism yields maximum rotation and placement as shown below 1. Pan Tilt Horizontal Rotation 355 How to Open the Gimbal Cover This Dome Camera has a vari-focal lens integrated inside the Gimbal. To make focal/focus adjustments, the Gimbal cover needs to be temporarily removed. If lens adjustments are not necessary, skip to Page 10. Gimbal Base Point-B Step-1 As shown on the right, hold the Gimbal base firmly in place with one hand. Step-2 Gently press Points A & B with other hand and pull the Gimbal cover off. Step-3 Make necessary lens adjustments. Step-4 Replace the Gimbal cover by gently pressing back onto the Gimbal base. Point-A Gimbal Cover 9

10 Vari-focal, DC Auto Iris Lens Adjustments 1. Remove the Gimbal cover from the Gimbal base. Zoom Focus UP RIGHT LEFT DOWN Gimbal Cover OSD Menu Button 2. Loosen Zoom & Focus screws and make necessary adjustments as shown. Field of View: Telephone (T) to Wode (W) Focus: Near(N) to infinity( ) N T W Adjust Focus Adjust Angle for Field of View 3. Replace the Gimbal cover back to the Gimbal base. 10

11 OSD Menu Instructions Menu & Setting Details Main Menu LENS SHUTTER WHITE BALANCE BACKLIGHT AGC DNR DSS DC FLK ESC MANUAL ATW MANUAL AWC LOW MIDDLE HIGH LOW MIDDLE HIGH LOW MIDDLE HIGH AUTO BRIGHTNESS 1-70(25) BRIGHTNESS 1-70(25) SHUTTER 1/60-1/ RED 0-256(32) BLUE 1-256(39) TOP DOWN LEFT RIGHT BRIGHTNESS 1-70 (25) LIMIT x2 - x128(x8) 11

12 OSD Menu Instructions SPECIAL Main Menu CAMERA ID COLOR SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN ON COLOR AUTO BW INT ON AREA SEL AREA1,2,3, or 4 AREA STATE ON/ TOP DOWN LEFT RIGHT ON AREA SEL AREA1,2,3, or 4 AREA STATE ON/ TOP DOWN LEFT RIGHT ON ON LEVEL 0-31(8) 12

13 OSD Menu Istructions Main Menu A. LENS This function is used to adjust the brightness of the screen. - DC : The brightness can be adjusted in DC mode. The brightness can be adjusted within the range of 1 to 70. B. SHUTTER This function is used to control the condition and shutter speed : Shutter speed is fixed. - FLK : Select FLK mode when flicking occurs on the screen due to imbalance between illumination and frequency. - ESC : Select ESC mode for automatic control of shutter speed. The speed is controlled automatically according to the brightness of the screen. - Manual : Select MANUAL mode to control shutter speed manually. C. WHITE BALANCE This function is used to balance the screen color. - ATW (Auto Tracking White Balance): Select ATW when using within the color temperature range of 1,800 K to 10,500 K (Ex. Fluorecent light, outdoor, sodium vapor lamp or inside tunnels) - AWC (Auto White Balance Control): Press SET key while the camera is directed at a piece of white paper to obtain the optimum state under current illumination. If the environment including the light source is changed, you have to adjust the white balance again. 13

14 OSD Menu Istructions 14

15 OSD Menu Istructions 15

16 OSD Menu Istructions I 16

SVD-4120A SSNR Low Light, WDR, Day & Night Vandal-Proof Color Dome Camera

SVD-4120A SSNR Low Light, WDR, Day & Night Vandal-Proof Color Dome Camera Low Light, WDR, Day & Night Vandal-Proof Color Dome Camera SVD-4120A www.samsungcctv.com Built-in chip Originally Developed by Samsung Techwin Crisp and clear images in any light Samsung Techwin's new