ACP (ANSYS Composite Prep/Post) Jim Kosloski

Transcription

1 ACP (ANSYS Composite Prep/Post) Jim Kosloski

2 ACP Background ANSYS Composite PrepPost is an add-on module dedicated to the modeling of layered composite structures. ACP is now included with the Mechanical Enterprise licenses 2

3 Typical ACP Usage A shell element model is developed in Mechanical Meshing shell geometry, applying loads and boundary conditions. Can be in ANSYS Mechanical or Mechanical APDL Define materials (Engineering Data, or APDL) Import the models in ANSYS Composite PrepPost Define Composite Fabrics: Fabric: a material and a thickness Laminate: an assembly of fabrics (with orientations) Define the element orientation (so as to properly orient materials) Define the ply sequence for groups of elements (usually corresponding to faces of the geometry) Solve the model - computed by the standard ANSYS solver, in batch mode. Post-process the results in ACP: deformations, thicknesses and failure criteria. 3

4 Incorporation into WB Architecture ACP is incorporated directly into the WB architecture. Define composite material properties Import/Generate surface geometry Set-up composite material fabric definitions, element orientations, ply layup, etc Generate Shell Mesh 4

5 Composite Materials In Engineering Data, there is now a composite materials library. Show Libraries Material does not need to be assigned to bodies in Mechanical. Material assignment is done in ACP. All materials in Engineering Data are brought into ACP. 5

6 Starting ACP Once shell mesh is generated and materials defined, ACP can be started by right click: Edit 6

7 Solving and Post-processing Once the model is setup in APC(Pre) it can be linked to whatever type of analyses you need to solve: Then connect ACP(Post) to the Solution of that analysis. 7

8 ACP Modeling Capabilities Multiple oriented element sets allow for multi-laminate build-up. 8

9 Parametric Modeling of Composites Since ACP is integrated into Workbench, the composite data from ACP will be updated with any parameter changes in WB. Example below shows parametric changes of doubler width shown in red. 9

10 Post-processing of Composite Results Efficient post-processing of composite-specific results quantities. New Sampling Element post-processing. Plot worst case failure criteria over all layers. Pick element and see stress/strain and failure through the thickness 10

11 Post-processing of Composite Results Make thru-thickness stress plots and account for interlaminar normal stresses with shells. Traditional shell approaches can not account for interlaminar normal stress (shown in blue curve) ANSYS Composite PrepPost can predict these base on the work of Roos, Kress, & Ermanni Critical Stresses in Bend Thru-Thickness ILS & ILN Stress Plots Solids Thru-Thickness ILS & ILN Stress Plots Shells 11

12 Post-processing of Composite Results Sandwich Construction Post-processing. Wrinkling Local buckling of a face sheet under compression Failure indicator available using shell modeling of sandwich Core Failure Local failure of core in shear or tensile loading Failure indicator available using shell modeling of sandwich 12

13 Advanced ACP Capabilities Fiber orientation prediction and modification. Use internal ACP draping simulation to compute orientation changes due to geometry curvature, develop flat pattern. Modify the fiber orientation to something that is actually observed on the manufacturing floor through alignment with local rosettes. 13

14 Advanced ACP Capabilities 3D Solid Modeling: If a composite part is thick and bulky a shell mesh may not be sufficient to predict accurate results. One of ACP(Pre) strengths is that the 2D shell mesh can be extruded into a 3D solid model. CAD support: STEP and IGES geometries can be imported to define thick cores or use as guides for 3D extrusions. 14

15 Advanced ACP Capabilities Even more Map composite thickness and angles through table look-up. Build complex assemblies including contact. Customize layups using scripts and tables (Filament winding) Multiple solid models can be combined through links to MAPDL. 2-Way FSI with composites 15

16 ACP v17.0 Enhancements Variable Material Data The temperature-, shear-, and degradation factor-dependent material data functionality has been extended. In release 17.0, the composite material elasticity and strength properties can depend on any scalar user-defined field. This allows you to account for not only basic effects like temperature or plyshearing due to draping on the composite behavior of the simulation, but any other factor such as void content, degree of curing, or humidity. 16

17 ACP v17.0 Enhancements Enhanced Composite Workflows Multiple ACP-Pre systems and Mechanical Models can now be assembled in one analysis system. This functionality can be used in design studies where the composite definition remains the same but different geometries are evaluated. Submodeling is another situation where this functionality can be used. In a scenario where two models are to share the same ACP (Pre) Setup, one setup cell is dragged on to the other. ACP maps as much information onto the second model as possible. It is advised to use common Named Selections as well as the same Engineering 17

18 ACP v17.0 Enhancements Enhanced Composite Workflows Composite workflows for shell and solid element analyses have been streamlined. Composite shells and composite solids follow the same workflow logic and composite shell models can now be combined with composite solid models. 18

19 ACP v17.0 Enhancements Interactive Lay-up Definition in Excel A new Excel Link interface allows for efficient, live, spreadsheet-based definition and data exchange on composite lay-ups in ACP. 19

20 Mechanical Composites Enhancements The following composite enhancements have been made at Release 17.0 for working with composite (layered) elements directly in Mechanical: Additional Result Types for Composite Analysis. Mechanical now supports ply-based User Defined results and Elemental Coordinate System results. These results are supported through traditional Details view scoping as well as through the automated context menu (right-click) option when you select one or more Ply objects. 20

21 Mechanical Composites Enhancements Specifying Ply-based Named Selections using Worksheet Criteria. You can now define ply-based Named Selection using the Criterion option of the Worksheet. 21

22 Mechanical Composites Enhancements Ply Graphics Options. In addition to Ply fiber direction, transverse direction, and Element Normal direction, Mechanical now enables you to view Ply normal direction as well as Element reference direction using new toolbar options. 22

23 Element Orientation 1. Element Orientations can be applied via manual element selection or using a Named Selection. 2. Element Orientations can be defined using different coordinate systems within the same body. 3. Element triad display can be controlled using the element orientation toolbar