TRAINING GUIDE SOLIDS-LESSON-3

Size: px
Start display at page:

Download "TRAINING GUIDE SOLIDS-LESSON-3"

Transcription

1 TRAINING GUIDE SOLIDS-LESSON-3

2 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing 2-dimensional drawing Create the solid model Revolve and Create a solid body Boolean remove a solid body Create Solid Chamfers Create Solid Fillets Solids-Lesson-3-1

3 Solids-Lesson-3 SOLIDS-LESSON-3 DRAWING Solids-Lesson-3-2

4 Mastercam Training Guide SOLIDS-LESSON-3 - THE PROCESS TASK 1: TASK 2: TASK 3: TASK 4: TASK 5: TASK 6: TASK 7: TASK 8: Solid Model Creation Setting the environment Open an existing Mastercam file Create the revolved solid Create the block solid body Boolean subtraction of a solid Create chamfers 4 places Create Fillets 4 places Save the drawing Solids-Lesson-3-3

5 Solids-Lesson-3 TASK 1: SETTING THE ENVIRONMENT Before starting the geometry creation you should set up the grid, toolbars and machine type as outlined in the Setting the environment section at the beginning of this text: 1. Set up the Grid. This will help identify the location of the origin. 2. Load the Workspace SETTINGS>Load Workspace>3D Toolpaths to machine a 3D part. TASK 2: OPEN AN EXISTING MASTERCAM FILE In this lesson you will use an existing Mastercam file that contains the 2D geometry only. In this lesson we will only be creating the Solid Geometry. The Mastercam file for this lesson is located on the Disk accompanying the Training Guide or as a download in one of the Steps in Solids Lesson 3 of the Online Course. 1. Select File>Open>Solids-Lesson If confronted with the System Configuration dialog box activate the radio button for All settings. System Configuration (switch units) dialog box When you open a part file that uses different units (English or metric) from those currently in use, Mastercam automatically displays this dialog box, which informs you that Mastercam is switching units and loading an alternate default configuration file. In order to complete the operation, select one of the following options: Units: Tells Mastercam to use only the units from the new configuration file. (default) All settings: Tells Mastercam to load all settings from the new configuration file. 3. Select the OK button to exit the System Configuration dialog box if required. 4. The screen should look like the one below: Solids-Lesson-3-4

6 Mastercam Training Guide 5. Select File. 6. Select Save as. 7. In the File name box, type Solids-Lesson Save to an appropriate location. 9. Select the Save button to save the file and complete this function. Solid Body Creation TASK 3: CREATE THE REVOLVED SOLID In this task you will create the solid cavity of the part by revolving the geometry created. 1. Select the Top View. 2. From the Menu Select SOLIDS>Revolve On the screen you will now see the Chaining dialog box, with the Chain Button selected as shown by the arrow. In the graphics screen a prompt to Select chain(s) to extrude is displayed. 3. Select the chain as shown in the Graphics Screen diagram: Chaining Box Graphics Screen 4. Click on the OK icon. Solids-Lesson-3-5

7 Solids-Lesson-3 5. The Select line to be used as axis of rotation prompt appears. Select the centreline of the cavity as shown below: 6. Change the view to isometric by clicking on the Isometric icon. 7. An arrow will appear as shown below, make sure the arrow is pointing down. If it is pointing up click on the Reverse All icon in the Solid Extrude dialog box. Note: you may have to unzoom the image to see the direction the arrow is pointing. Solids-Lesson-3-6

8 Mastercam Training Guide 8. Make the necessary changes as shown below in the Solid Revolve dialog window. Activate Create Body and set the Start Angle to 0 and End Angle is set to Click on the OK icon in the Solid Revolve dialog window Your screen should look like the screenshot below: Solids-Lesson-3-7

9 Solids-Lesson Select Alt and S to shade the solid extrusion or click on the Outlined Shaded icon at the top of the screen. 11. Change the view again by clicking on the Dynamic Rotation icon. 12. With the cursor on the image, click the left mouse button and move the mouse around. Note how the image moves around. To stop the image from moving click the left mouse button. 13. Try using the different icons in the menu bar shown above to change the view of the image. 14. You can also change the view of the image by right clicking the mouse button and selecting from the available menu as shown below: Solids-Lesson-3-8

10 Mastercam Training Guide TASK 4: CREATE THE BLOCK SOLID BODY 1. Activate a wireframe image by selecting the Alt and S keys or by clicking on the Wireframe icon at the top of the screen: 2. Select the Top View. 3. From the Menu Select SOLIDS>Extrude On the screen you will now see the Chaining dialog box, with the Chain Button selected as shown by the arrow. In the graphics screen a prompt to Select chain(s) to extrude is displayed. 4. Select the chain as shown in the Graphics Screen diagram: Chaining Box Graphics Screen 5. Click on the OK icon. Solids-Lesson-3-9

11 Solids-Lesson-3 6. Change the view to isometric by clicking on the Isometric icon. 7. An arrow will appear on one of the corners as shown below, make sure the arrow is pointing down. If it is pointing up click on the Reverse All icon in the Solid Extrude dialog box. Note: you may have to unzoom the image to see the direction the arrow is pointing. Solids-Lesson-3-10

12 Mastercam Training Guide 8. Make the necessary changes as shown below in the Solid Extrude dialog window. Activate Create Body and set the Distance to Click on the OK icon in the Solid Extrude dialog window Your screen should look like the screenshot below: Wireframe image Solid image Solids-Lesson-3-11

13 Solids-Lesson-3 TASK 5: BOOLEAN SUBTRACTION OF A SOLID In this task, the two separate solid bodies that have been created will be combined. In the solids tree, both bodies are present as shown in the image below. Using Boolean remove the solid body representing the cavity can be removed from the solid representing the stock material. 1. Activate a wireframe image by selecting the Alt and S keys or by clicking on the Wireframe icon at the top of the screen: 2. From the Menu Select SOLIDS>Boolean Boolean Boolean functions construct a solid from combinations of two or more existing solids. You can merge solids, remove solids from one another, and find the common region of overlapping solids. Solids-Lesson-3-12

14 Mastercam Training Guide 3. On the screen you will now be prompted to Select target body for boolean operation. Select the stock solid body as shown in the image below: 4. The prompt Select tool body for boolean operation will now be displayed and the Solid Selection dialog box appears. In the Solid Selection dialog box only activate Body selection. Select the cavity solid body as shown below: 5. Click on the OK icon in the Solid Selection dialog box. Solids-Lesson-3-13

15 Solids-Lesson-3 6. Make the necessary changes as shown below in the Boolean dialog window. Activate Remove. 7. Click on the OK icon in the Boolean dialog box. 8. In the solids tree there is now only one solid entity which contains the Boolean Remove feature, as seen below: Solids-Lesson-3-14

16 Mastercam Training Guide 9. To change from a wireframe image to a solid image select the Alt and S keys or the Shading icon. Your screen should look like the screenshots below: Wireframe image Solid image Solids-Lesson-3-15

17 Solids-Lesson-3 TASK 6: CREATE CHAMFERS 4 PLACES In this task you will create four x 45 degree chamfers on the edges of the stock. The chamfers are not called out on the drawing; this task is to get some experience using Solid Chamfers. 1. Activate a wireframe image by selecting the Alt and S keys or by clicking on the Wireframe icon at the top of the screen: 2. From the Menu Select SOLIDS>Chamfer>One-Distance Chamfer One-Distance Chamfer uses edge blending to create a symmetrical bevelled edge with the same chamfer distance for both edge faces. You determine the size of the chamfer by entering the distance value. Two-Distance Chamfer Two-Distance Chamfer uses edge blending to create a bevel based on two distances and a reference face. Mastercam uses Distance 1 to calculate the extent of the chamfer between the reference face and the selected edge. Distance 2 determines the extent of the chamfer between the complementary face and the selected edge. Distance and Angle Chamfer Distance and Angle Chamfer uses edge blending to create a bevel based on a distance, an angle, and a reference face. Mastercam uses the distance and the angle to calculate the extent of the chamfer on the selected edge, relative to the reference face. Solids-Lesson-3-16

18 Mastercam Training Guide 3. On the screen you will now be prompted to Select entities to chamfer and the Solid Selection dialog box appears. In the Solid Selection dialog box only activate Edge selection. Solid Selection dialog box Use this dialog box to set filters for solid selection functions. The following table lists the available options: The Last button reselects the entities selected for the previous operation. The Verify Selection button displays a toolbar (shown below) with which you can cycle through selectable entities. 4. Now select the four edges on the top of the stock as shown below. As you position the cursor close to an edge you will see the visual cue for edged selection. 5. Click on the OK icon after completing the selection of the four edges. Solids-Lesson-3-17

19 Solids-Lesson-3 6. Make the necessary changes as shown below in the One-Distance Chamfer dialog window. Set Distance to Click on the OK icon in the One-Distance Chamfer dialog box. 8. Select Alt and S to shade the solid extrusion or click on the Outlined Shaded icon at the top of the screen. Your screen should look like the screenshot below: Solids-Lesson-3-18

20 Mastercam Training Guide TASK 7: CREATE FILLETS 4 PLACES In this task you will create four fillets on the vertical edges of the stock. The fillets are not called out on the drawing; this task is to get some experience using Solid Fillets. 1. Activate a wireframe image by selecting the Alt and S keys or by clicking on the Wireframe icon at the top of the screen: 2. From the Menu Select SOLIDS>Fillet>Constant Radius Fillet Constant Radius Fillet uses edge blending to produce a rounded edge, introducing new faces that are tangent to the edges' adjacent faces. You determine the extent of the fillet by inputting a constant radius value. Variable Radius Fillet Variable Radius Fillet uses edge blending to produce a rounded edge, introducing new faces that are tangent to the edges' adjacent faces. You determine the extent of the fillet by inputting various radius values along the edge. You can also specify radius positions Face-Face Fillet Face-Face Fillet uses two faces or two sets of faces that are blended together to create a fillet. Mastercam will use various ways of creating the fillets depending on the operation type that is selected Solids-Lesson-3-19

21 Solids-Lesson-3 3. On the screen you will now be prompted to Select entities to fillet and the Solid Selection dialog box appears. In the Solid Selection dialog box only activate Edge selection. 4. Now select the four vertical edges on the stock as shown below. As you position the cursor close to an edge you will see the visual cue for edged selection. 5. Click on the OK icon after completing the selection of the four vertical edges. Solids-Lesson-3-20

22 Mastercam Training Guide 6. Make the necessary changes as shown below in the Constant Radius Fillet dialog window. Set Radius to Click on the OK icon in the Constant Radius Fillet dialog box. 8. Select Alt and S to shade the solid extrusion or click on the Outlined Shaded icon at the top of the screen. Your screen should look like the screenshot below: TASK 8: SAVE THE DRAWING 1. Select File>Save... Solids-Lesson-3-21

23 Solids-Lesson-3 IF YOU WISH TO CREATE THE TOOLPATHS FOR THIS LESSON THE TOOL LIST AND PROCESS IS LISTED BELOW: NOTE: For step by step instructions on how to create the toolpaths for this solids lesson please refer to the Mastercam Training Guide - Mill 2D by CamInstructor diameter bull end mill with a corner radius to rough machine the pocket diameter ball end mill to finish machine the pocket. SOLIDS-LESSON-3 - TOOLPATH PROCESS Toolpath Creation TASK 10: Define the rough stock using stock setup TASK 11: Rough the pocket using surface pocket TASK 12: Finish the pocket using surface high speed waterline TASK 13: Verify the toolpath TASK 14: Save the updated Mastercam file TASK 15: Post and create the CNC code file Solids-Lesson-3-22

24 Mastercam Training Guide SOLIDS-LESSON-3A EXERCISE Solids-Lesson-3-23

25 Solids-Lesson-3 SOLIDS-LESSON-3B EXERCISE Solids-Lesson-3-24

26 Mastercam Training Guide Solids-Lesson-3-25

TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF

TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC

More information

TRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF

TRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC

More information

TRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF

TRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC

More information

TRAINING GUIDE. Sample Only. not to be used. for training MILL-LESSON-15 CORE ROUGHING, WATERLINE, AND SURFACE FINISH LEFTOVER

TRAINING GUIDE. Sample Only. not to be used. for training MILL-LESSON-15 CORE ROUGHING, WATERLINE, AND SURFACE FINISH LEFTOVER TRAINING GUIDE MILL-LESSON-15 CORE ROUGHING, WATERLINE, AND SURFACE FINISH LEFTOVER Mastercam Training Guide Objectives You will use a provided model for Mill-Lesson-15, then generate the toolpaths to

More information

TRAINING GUIDE WCS - VIEW MANAGER - PART-2

TRAINING GUIDE WCS - VIEW MANAGER - PART-2 TRAINING GUIDE WCS - VIEW MANAGER - PART-2 Mastercam Training Guide Objectives The learner will create the geometry and toolpaths for WCS-Part-2. This Lesson will cover the following topics: Create a 3-dimensional

More information

TOOLPATHS TRAINING GUIDE. Sample. Distribution. not for MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR

TOOLPATHS TRAINING GUIDE. Sample. Distribution. not for MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR TOOLPATHS TRAINING GUIDE MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR Mill-Lesson-4 Objectives You will generate a toolpath to machine the part on a CNC vertical milling machine. This lesson covers the following

More information

TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL

TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives Previously in Mill-Lesson-6 and Mill-Lesson-7 geometry was created and machined using standard Mastercam methods.

More information

TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL

TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives This lesson will use the same Feature Based Machining (FBM) methods used in Mill-Lesson- FBM-1, how ever this

More information

Jewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3

Jewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3 Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in

More information

TRAINING GUIDE WCS-PART-1

TRAINING GUIDE WCS-PART-1 TRAINING GUIDE WCS-PART-1 Mastercam Training Guide Objectives The learner will create the geometry for WCS-Part-1. This Lesson will cover the following topics: Create a 3-dimensional drawing by: Creating

More information

Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies

Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently

More information

Mill Level 1 Training Tutorial

Mill Level 1 Training Tutorial To order more books: Call 1-800-529-5517 or Visit www.inhousesolutions.com or Contact your Mastercam dealer Mastercam X 5 Copyright: 1998-2010 In-House Solutions Inc. All rights reserved Software: Mastercam

More information

Solid Problem Ten. In this chapter, you will learn the following to World Class standards:

Solid Problem Ten. In this chapter, you will learn the following to World Class standards: C h a p t e r 11 Solid Problem Ten In this chapter, you will learn the following to World Class standards: 1. Sketch of Solid Problem Ten 2. Starting a 3D Part Drawing 3. Modifying How the UCS Icon is

More information

Chapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1

Chapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1 Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click

More information

Autodesk Inventor - Basics Tutorial Exercise 1

Autodesk Inventor - Basics Tutorial Exercise 1 Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be

More information

Mastercam X9 for SOLIDWORKS

Mastercam X9 for SOLIDWORKS Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and

More information

Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New

Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.

More information

3D Design with 123D Design

3D Design with 123D Design 3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A

More information

Parametric Modeling with UGS NX 4

Parametric Modeling with UGS NX 4 Parametric Modeling with UGS NX 4 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric Modeling

More information

Lesson 1 Parametric Modeling Fundamentals

Lesson 1 Parametric Modeling Fundamentals 1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.

More information

GETTING STARTED WITH MASTERCAM SOLIDS

GETTING STARTED WITH MASTERCAM SOLIDS GETTING STARTED WITH MASTERCAM SOLIDS June 2017 GETTING STARTED WITH MASTERCAM SOLIDS June 2017 2017 CNC Software, Inc. All rights reserved. Software: Mastercam 2018 Terms of Use Use of this document is

More information

Exercise Guide. Published: August MecSoft Corpotation

Exercise Guide. Published: August MecSoft Corpotation VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4

More information

SolidWorks 2013 and Engineering Graphics

SolidWorks 2013 and Engineering Graphics SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following

More information

Brief Introduction to MasterCAM X4

Brief Introduction to MasterCAM X4 Brief Introduction to MasterCAM X4 Fall 2013 Meung J Kim, Ph.D., Professor Department of Mechanical Engineering College of Engineering and Engineering Technology Northern Illinois University DeKalb, IL

More information

Parametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS

Parametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS Parametric Modeling With Autodesk Inventor R10 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric

More information

Feature-based CAM software for mills, multi-tasking lathes and wire EDM. Getting Started

Feature-based CAM software for mills, multi-tasking lathes and wire EDM.  Getting Started Feature-based CAM software for mills, multi-tasking lathes and wire EDM www.featurecam.com Getting Started FeatureCAM 2015 R3 Getting Started FeatureCAM Copyright 1995-2015 Delcam Ltd. All rights reserved.

More information

Chapter 2 Parametric Modeling Fundamentals

Chapter 2 Parametric Modeling Fundamentals 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the "Shape before Size" Approach Use

More information

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD 3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions

More information

Getting Started with Mastercam Solids. March 2016

Getting Started with Mastercam Solids. March 2016 Getting Started with Mastercam Solids March 2016 Mastercam 2017 Solids Getting Started TERMS OF USE Date: March 2016 Copyright 2016 CNC Software, Inc. All rights reserved. Software: Mastercam 2017 Use

More information

Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1

Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1 Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click

More information

Autodesk Inventor 2019 and Engineering Graphics

Autodesk Inventor 2019 and Engineering Graphics Autodesk Inventor 2019 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the

More information

SOLIDWORKS 2016 and Engineering Graphics

SOLIDWORKS 2016 and Engineering Graphics SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following

More information

Fig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1

Fig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1 Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam

More information

Solid Bodies and Disjointed Bodies

Solid Bodies and Disjointed Bodies Solid Bodies and Disjointed Bodies Generally speaking when modelling in Solid Works each Part file will contain single solid object. As you are modelling, each feature is merged or joined to the previous

More information

MASTERCAM DYNAMIC MILLING TUTORIAL. June 2018

MASTERCAM DYNAMIC MILLING TUTORIAL. June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject

More information

Solid Modeling: Part 1

Solid Modeling: Part 1 Solid Modeling: Part 1 Basics of Revolving, Extruding, and Boolean Operations Revolving Exercise: Stepped Shaft Start AutoCAD and use the solid.dwt template file to create a new drawing. Create the top

More information

Autodesk Inventor 6 Essentials Instructor Guide Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the follow

Autodesk Inventor 6 Essentials Instructor Guide Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the follow Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the following topics and provides exercises for students to practice their skills. Day Two Topic: How to create

More information

Introduction to the Work Coordinate System (WCS) April 2015

Introduction to the Work Coordinate System (WCS) April 2015 Introduction to the Work Coordinate System (WCS) April 2015 Mastercam X9 Introduction to WCS TERMS OF USE Date: April 2015 Copyright 2015 CNC Software, Inc. All rights reserved. Software: Mastercam X9

More information

CATIA V5 Parametric Surface Modeling

CATIA V5 Parametric Surface Modeling CATIA V5 Parametric Surface Modeling Version 5 Release 16 A- 1 Toolbars in A B A. Wireframe: Create 3D curves / lines/ points/ plane B. Surfaces: Create surfaces C. Operations: Join surfaces, Split & Trim

More information

Lesson 5 Solid Modeling - Constructive Solid Geometry

Lesson 5 Solid Modeling - Constructive Solid Geometry AutoCAD 2000i Tutorial 5-1 Lesson 5 Solid Modeling - Constructive Solid Geometry Understand the Constructive Solid Geometry Concept. Create a Binary Tree. Understand the basic Boolean Operations. Create

More information

Mastercam X6 for SolidWorks Toolpaths

Mastercam X6 for SolidWorks Toolpaths Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.

More information

Memo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.

Memo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks

More information

Chapter 2 Parametric Modeling Fundamentals

Chapter 2 Parametric Modeling Fundamentals 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the Shape before Size Approach Use the

More information

CHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.

CHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen. Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point.

More information

Toolpaths for Fuselage

Toolpaths for Fuselage Mastercam Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Machine Type and Stock Setup. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. If necessary, display

More information

A Comprehensive Introduction to SolidWorks 2011

A Comprehensive Introduction to SolidWorks 2011 A Comprehensive Introduction to SolidWorks 2011 Godfrey Onwubolu, Ph.D. SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Chapter 2 Geometric Construction Tools Objectives: When

More information

Parametric Modeling with NX 12

Parametric Modeling with NX 12 Parametric Modeling with NX 12 NEW Contains a new chapter on 3D printing Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the

More information

MASTERCAM WIRE TUTORIAL. June 2018

MASTERCAM WIRE TUTORIAL. June 2018 MASTERCAM WIRE TUTORIAL June 2018 MASTERCAM WIRE TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject to the Mastercam End

More information

Chapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New

Chapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe

More information

CATIA Surface Design

CATIA Surface Design CATIA V5 Training Exercises CATIA Surface Design Version 5 Release 19 September 2008 EDU_CAT_EN_GS1_FX_V5R19 Table of Contents (1/2) Creating Wireframe Geometry: Recap Exercises 4 Creating Wireframe Geometry:

More information

Tutorial Second Level

Tutorial Second Level AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn

More information

Solid Bodies and Disjointed bodies

Solid Bodies and Disjointed bodies Solid Bodies and Disjointed bodies Generally speaking when modelling in Solid Works each Part file will contain single solid object. As you are modelling, each feature is merged or joined to the previous

More information

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now

More information

TUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.

TUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.

More information

Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.

Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS. Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click

More information

Constructing treatment features

Constructing treatment features Constructing treatment features Publication Number spse01530 Constructing treatment features Publication Number spse01530 Proprietary and restricted rights notice This software and related documentation

More information

Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide

Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to

More information

Introduction to MasterCAM X4,7

Introduction to MasterCAM X4,7 Introduction to MasterCAM X4,7 Spring 2014 By Meung J. Kim, Ph.D., Professor Department of Mechanical Engineering Northern Illinois University 1 Preliminaries C-Plane: flat Construction plane that can

More information

Chapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.

Chapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll

More information

Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints

Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the

More information

4 & 5 Axis Mill Training Tutorials. To order more books: Call or Visit or Contact your Mastercam Dealer

4 & 5 Axis Mill Training Tutorials. To order more books: Call or Visit   or Contact your Mastercam Dealer 4 & 5 Axis Mill Training Tutorials To order more books: Call 1-800-529-5517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer Mastercam X Training Tutorials 4 & 5 Axis Mill Applications

More information

Adding Fillet, Shell, and Draft Features

Adding Fillet, Shell, and Draft Features Learn how to: Adding Fillet, Shell, and Draft Features I-DEAS Tutorials: Fundamental Skills add draft features add fillet features use the Ball Corner Fillet option add shell features Before you begin...

More information

CO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.

CO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.

More information

EZ-Mill EXPRESS TUTORIAL 2. Release 13.0

EZ-Mill EXPRESS TUTORIAL 2. Release 13.0 E-Mill EPRESS TUTORIAL 2 Release 13.0 Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to ECAM Solutions, Inc. It is made available

More information

3D AUTOCAD. The view we ve been working in is a top or plan view. From this view even a 3D drawing will appear 2D.

3D AUTOCAD. The view we ve been working in is a top or plan view. From this view even a 3D drawing will appear 2D. 3D AUTOCAD Thus far, we ve looked at tools and operations in 2D with work completed on only the X- and Y- axes. The axes symbol has been present on our screen but we haven t had much use for it. The view

More information

F1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the

F1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.

More information

Toolpaths for Fuselage

Toolpaths for Fuselage Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide

More information

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS

More information

CADCAM using Powermill

CADCAM using Powermill CADCAM using Powermill In this exercise you will create the toolpaths necessary to machine the Cowling model. Create a folder on your h: called Powermill. Inside this create a folder called cowling2009.

More information

Parametric Modeling with. Autodesk Fusion 360. First Edition. Randy H. Shih SDC. Better Textbooks. Lower Prices.

Parametric Modeling with. Autodesk Fusion 360. First Edition. Randy H. Shih SDC. Better Textbooks. Lower Prices. Parametric Modeling with Autodesk Fusion 360 First Edition Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites

More information

ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.

ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK. PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step

More information

Chapter 10. Creating 3D Objects Delmar, Cengage Learning

Chapter 10. Creating 3D Objects Delmar, Cengage Learning Chapter 10 Creating 3D Objects 2011 Delmar, Cengage Learning Objectives Extrude objects Revolve objects Manipulate surface shading and lighting Map artwork to 3D objects Extrude Objects Extrude & Bevel

More information

Modeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1

Modeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1 Modeling a Gear This tutorial describes how to create a toothed gear. It combines using wireframe, solid, and surface modeling together to create a part. The model was created in standard units. To begin,

More information

Part Design Features Recognition

Part Design Features Recognition CATIA V5 Training Foils Part Design Features Recognition Version 5 Release 19 January 2009 EDU_CAT_EN_FR1_FI_V5R19 1 About this course Objectives of the course Upon completion of this course you will be

More information

MFG12197 FeatureCAM Hands On Milling, turning and mill turn with Feature Based Machining

MFG12197 FeatureCAM Hands On Milling, turning and mill turn with Feature Based Machining MFG12197 FeatureCAM Hands On Milling, turning and mill turn with Feature Based Machining Jeremy Malan Delcam Learning Objectives Learn how to instantly machine parts once their features are defined Learn

More information

An Introduction to Autodesk Inventor 2010 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation

An Introduction to Autodesk Inventor 2010 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation An Introduction to Autodesk Inventor 2010 and AutoCAD 2010 Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation www.schroff.com 2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded

More information

Module 1: Basics of Solids Modeling with SolidWorks

Module 1: Basics of Solids Modeling with SolidWorks Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists

More information

Introduction to SolidWorks Basics Materials Tech. Wood

Introduction to SolidWorks Basics Materials Tech. Wood Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10

More information

Mastercam X6 for SolidWorks Toolpaths

Mastercam X6 for SolidWorks Toolpaths Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog

More information

Dynamic Milling. March 2015

Dynamic Milling. March 2015 Dynamic Milling March 2015 Mastercam X9 Dynamic Milling TERMS OF USE Date: March 2015 Copyright 2015 CNC Software, Inc. All rights reserved. Software: Mastercam X9 Use of this document is subject to the

More information

Parametric Modeling. with. Autodesk Inventor Randy H. Shih. Oregon Institute of Technology SDC

Parametric Modeling. with. Autodesk Inventor Randy H. Shih. Oregon Institute of Technology SDC Parametric Modeling with Autodesk Inventor 2009 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. 2-1 Chapter

More information

Changes from SolidWorks 2003 to SolidWorks 2004

Changes from SolidWorks 2003 to SolidWorks 2004 Changes from SolidWorks 2003 to SolidWorks 2004 The changes from SolidWorks 2003 to SolidWorks 2004 are primarily cosmetic. Consequently, it is quite easy to use the current edition of Learning SolidWorks

More information

Extrusion Revolve. ENGR 1182 SolidWorks 02

Extrusion Revolve. ENGR 1182 SolidWorks 02 Extrusion Revolve ENGR 1182 SolidWorks 02 Today s Objectives Creating 3D Shapes from 2D sketches using: Extrusion Revolve SW02 In-Class Activity Extrude a Camera Revolve a Wheel SW02 Out-of-Class Homework

More information

CNC Programming Simplified. EZ-Turn / TurnMill Tutorial.

CNC Programming Simplified. EZ-Turn / TurnMill Tutorial. CNC Programming Simplified EZ-Turn / TurnMill Tutorial www.ezcam.com Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to EZCAM Solutions,

More information

Figure 1: NC > 2 Axis menu > Options

Figure 1: NC > 2 Axis menu > Options Click To See: How to Use Online Documents SURFCAM Online Documents J 685)&$0Ã5HIHUHQFHÃ0DQXDO 7 &21),*85$7,21722/6 7.1 INTRODUCTION SURFCAM s default configuration parameters are contained in the SURFCAM.INI

More information

Autodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360

Autodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360 Overview Modeling techniques in Fusion 360 Modeling in Fusion 360 is quite a different experience from how you would model in conventional history-based CAD software. Some users have expressed that it

More information

Tutorial Second Level

Tutorial Second Level AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn

More information

VERO UK TRAINING MATERIAL. 2D CAM Training

VERO UK TRAINING MATERIAL. 2D CAM Training VERO UK TRAINING MATERIAL 2D CAM Training Vcamtech Co., Ltd 1 INTRODUCTION During this exercise, it is assumed that the user has a basic knowledge of the VISI-Series software. OBJECTIVE This tutorial has

More information

Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment. Kent L. Lawrence

Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment. Kent L. Lawrence ANSYS Workbench Tutorial Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS

More information

What s new in EZCAM Version 18

What s new in EZCAM Version 18 CAD/CAM w w w. e z c a m. com What s new in EZCAM Version 18 MILL: New Curve Machining Wizard A new Curve Machining Wizard accessible from the Machining menu automates the machining of common part features

More information

Additional Exercises. You will perform the following exercises to practice the concepts learnt in this course:

Additional Exercises. You will perform the following exercises to practice the concepts learnt in this course: Additional Exercises You will perform the following exercises to practice the concepts learnt in this course: Master Exercise : Mobile Phone Plastic Bottle Exercise 1 Master Exercise : Mobile Phone In

More information

How to Create a Fountain Pen

How to Create a Fountain Pen How to Create a Fountain Pen Lesson 4 How to Create a Fountain Pen This lesson will guide you in building a fountain pen. You will use the following tools: NURBS curves. Extrusion. Mirror. Trim. Blend

More information

AutoCAD 2013 Tutorial - Second Level: 3D Modeling

AutoCAD 2013 Tutorial - Second Level: 3D Modeling AutoCAD 2013 Tutorial - Second Level: 3D Modeling Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to

More information

3D printing Workshop Breakdown

3D printing Workshop Breakdown 3D printing Workshop Breakdown Opening Lecture/Remarks (20-30 Minutes) -Introduction to 3D modeling software Overview of what 3D modeling software is Introduction to 123D Design Introduction to 123D Design

More information

BobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill?

BobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill? BobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill? Q: I ve read FAQ #46 on how to set up my milling machine. How do I enable 4th axis to actually use it? A: Enabling 4th axis in the machine

More information

Toolpaths for Boat. OptiRough and Finish Waterline. Step 8. Click OK in the Machine Group Properties, Fig. 2. Stock display Click corner to move arrow

Toolpaths for Boat. OptiRough and Finish Waterline. Step 8. Click OK in the Machine Group Properties, Fig. 2. Stock display Click corner to move arrow Mastercam 2017 Chapter 33 Toolpaths for Boat A. Machine Type and Stock Setup. Step 1. If necessary, open your BOAT ROUND BOTTOM. Step 2. If necessary, display Toolpaths Manager. On the View tab click (Alt-O).

More information

MASTERCAM TRAINING GUIDE

MASTERCAM TRAINING GUIDE page 1 / 6 page 2 / 6 mastercam training guide pdf About This File. The Mastercam 2018 Mill Essentials Training Tutorial features concept-filled tutorials, challenging practice exercises and short quizzes

More information

VERO UK TRAINING MATERIAL

VERO UK TRAINING MATERIAL VERO UK TRAINING MATERIAL VISI Basic 2-D Modelling course (V-16) VISI Modelling 2D Design Introduction Many component designs follow a similar route, beginning with a 2D design, part modelled using solids

More information

Introduction to AutoCAD Chapter 15 Exercise 1

Introduction to AutoCAD Chapter 15 Exercise 1 Page 1 Introduction to AutoCAD 2010 Alf Yarwood Chapter 15 Exercise 1 1. Open AutoCAD 2010 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso3d.dwt. 3. Open the

More information

3D ModelingChapter1: Chapter. Objectives

3D ModelingChapter1: Chapter. Objectives Chapter 1 3D ModelingChapter1: The lessons covered in this chapter familiarize you with 3D modeling and how you view your designs as you create them. You also learn the coordinate system and how you can

More information