International Journal Of Global Innovations -Vol.1, Issue.II Paper Id: SP-V1-I2-221 ISSN Online:
|
|
- Clifton Lee
- 6 years ago
- Views:
Transcription
1 AN EFFICIENT IMPLEMENTATION OF FLOATING POINT ALGORITHMS #1 SEVAKULA PRASANNA - M.Tech Student, #2 PEDDI ANUDEEP - Assistant Professor, Dept of ECE, MLR INSTITUTE OF TECHNOLOGY, DUNDIGAL, HYD, T.S., INDIA. Abstract: - In computing, floating point describes a method of representing an approximation of a real number in a way that can support a wide range of values. Low power consumption and smaller area are some of the most important criteria for the fabrication of DSP systems and high performance systems. Optimizing the speed and area of the multiplier is a major design issue. However, area and speed are usually conflicting constraints so that improving speed results mostly in larger areas. This paper presents a floating point multiplier using Wallace and Dadda Algorithm of an IEEE 754 single precision floating point multiplier targeted for Xilinx. Improvement in speed multiplication of Dadda and Wallace multiplier is done thereby replacing Look ahead Carry adder. The methodology uses Exponent Calculator, Mantissa multiplier, Sign Calculator, and Normalization unit. Keywords: Dadda Algorithm, Wallace Algorithm, Floating point, multiplication, Spartan 6, ISE 13.1, VHDL language. I.INTRODUCTION Step 4. Finally the result is normalized such that there should be 1 in the MSB of the result (leading one). Single-precision binary floating-point is used due to its wider range over fixed point (of the same bit-width), even if at the Mohamed Al-Ashrfy, Ashraf Salem and Wagdy Anis cost of precision. Our discussion of floating point will focus implementation which handles the overflow and underflow almost exclusively on the IEEE floating-point standard (IEEE cases. Rounding is not implemented to give more precision 754) because of its rapidly increasing acceptance. Multiplying when using the multiplier in a multiply and Accumulate floating point numbers is a critical requirement for DSP (MAC) unit. And an implementation of a floating point applications. The possible ways to represent real numbers in multiplier that supports the IEEE binary interchange binary format floating point numbers are; the IEEE 754 format. The multiplier doesn t implement rounding and just standard [1] represents two floating point formats, Binary presents the significant multiplication result as is (48 bits). interchange format and Decimal interchange format. This In 2013, B. Jeevan, et al, shows a high speed binary floating paper focuses only on single precision normalized binary point multiplier based on Dadda Algorithm. In this interchange format. Representation of single precision improvement in speed of multiplication of mantissa is done normalized binary interchange format is shown in Fig.1. It using Dadda multiplier thereby replacing Carry Save consists of a one bit sign (S), an eight bit exponent (E), and a Multiplier. The design achieves high speed with maximum twenty three bit fraction (M or Mantissa). frequency of 526 MHz compared to existing floating point Z = (-1S) * 2 (E - Bias) * (1.M) (1) multipliers. The floating point multiplier is developed to handle the underflow and overflow cases. The significant Where M = n n n n n0 2- multiplication time is reduced by using Dadda Algorithm. 23; Bias = 127. DADDA MULTIPLIER Figure 1 IEEE Single Precision Floating Point Format Floating point multiplication of two numbers is made in four steps: Step1. Exponents of the two numbers are added directly, extra bias is subtracted from the exponent result. Step 2. Significands multiplication of the two numbers using Dadda & Wallace algorithm. Step 3. Calculating the sign by XORing the sign of the two numbers. Dadda proposed a sequence of matrix heights that are predetermined to give the minimum number of reduction stages. To reduce the N by N partial product matrix, dada multiplier develops a sequence of matrix heights that are found by working back from the final two-row matrix. In order to realize the minimum number of reduction stages, the height of each intermediate matrix is limited to the least integer that is no more than 1.5 times the height of its successor. Fig. shows the process of reduction for a dadda multiplier is developed using the following recursive algorithm 1. Let d1=2 and dj+1 = [1.5*dj], where dj is the matrix height for the jth stage from the end. Find the smallest j such that at Paper ijgis.com OCTOBER/2014 Page 235
2 least one column of the original partial product matrix has more than dj bits. 2. In the jth stage from the end, employ (3, 2) and (2, 2) counter to obtain a reduced matrix with no more than dj bits in any column. 3. Let j = j-1 and repeat step 2 until a matrix with only two rows is generated. This method of reduction, because it attempts to compress each column, is called a column compression technique. Another advantage of utilizing Dadda multipliers is that it utilizes the minimum number of (3, 2) counters. {Therefore, the number of intermediate stages is set in terms of lower bounds: 2, 3, 4, 6, 9... Figure 2.Dot diagram for 8 by 8 Dadda Multiplier II. RELATED WORK Floating point implementation on FPGAs has been the interest of many researchers. Oklobdzija implemented 32- bit and 64-bit leading zero detector (LZD) circuit using CMOS and ECL technology. In Pavle Belanovic and Miriam Leeser implemented reconfigurable floating point arithmetic unit using VHDL, which is mapped on to Xilinx XCV1000 FPGA. K. Scott Hemmert Keith and D. Underwood implemented open source library of highly optimized floating point units for Xilinx FPGAs. The units are fully IEEE compliant. The double precision add and multiply achieved the operating frequency of 230 MHz using a 10 stage adder pipeline and a 12 stage multiplier pipeline. In floating point adder was implemented using Leading One Predictor (LOP) algorithm instead of Leading One Detector (LOD) algorithm. The main function of the LOP is to predict the leading number of zeros in the addition result, working in parallel with the 2 s complement adder. Dhiraj Sangwan and Mahesh K. Yadav implemented adder/subtractor and multiplication units for floating point arithmetic using VHDL. The floating point multiplication operation was implemented using sequential architecture based on Booth s Radix-4 recoding algorithm. For floating point addition, the sequential addition could have been complex so the combinational architecture has been implemented. In double precision floating point adder/subtractor was implemented using dynamic shifter, LOD, priority encoder. The design achieved the operating frequency of 353 MHz for a latency of 12 clock cycles. In an IEEE-754 single precision pipelined floating point multiplier is implemented on multiple FPGAs (4 Actel A1280). Nabeel Shirazi, Walters, and Peter Athanas implemented custom 16/18 bit three stage pipelined floating point multiplier, that doesn t support rounding modes. L.Louca, T.A.Cook, W.H. Johnson implemented a single precision floating point multiplier by using a digit-serial multiplier and Altera FLEX The design achieved 2.3 MFlops and doesn t support rounding modes. In a parameterizable floating point multiplier is implemented using five stages pipeline, Handel-C software and Xilinx FPGA. The design achieved the operating frequency of 28MFlops.The floating point unit is implemented using the primitives of Xilinx Spartan-6 FPGA. The design achieved the operating frequency of 100 MHz with a latency of 4 clock cycles. Mohamed Al-Ashrafy, Ashraf Salem, and Wagdy Anis implemented an efficient IEEE-754 single precision floating point multiplier and targeted for Xilinx Spartan-6 FPGA. The multiplier handles the overflow and underflow cases but rounding is not implemented. The design achieves 301 MFLOPs with latency of three clock cycles. The multiplier was verified against Xilinx floating point multiplier core. The double precision floating point adder/subtractor and multiplier presented here is based on IEEE-754 binary floating standard. We have designed a high speed double precision floating point adder/subtractor and multiplier using Verilog language and ported on Xilinx Spartan-6 FPGA. Adder/subtractor and multiplier operates at very high frequencies of and MFlops and occupies 660 and 648 slices respectively. It handles the overflow, underflow cases and rounding mode. III. FLOATING POINT ALGORITHM Multiplying two numbers in floating point format is done by Adding the exponent of the two numbers then subtracting the bias from their result. Multiplying the significand of the two numbers Calculating the sign by XORing the sign of the two numbers. In order to represent the multiplication result as a normalized number there should be 1 in the MSB of the result (leading one).the following steps are necessary to multiply two floating point numbers. Step1. Multiplying the significand, i.e., (1.M1*1.M2) Step2. Placing the decimal point in the result Step3. Adding the exponents, i.e., (E1 + E2 Bias) Step4. Obtaining the sign i.e. s1 xor s2 Step5. Normalizing the result, i.e., obtaining 1 at the MSB of the results significand Step6. Rounding the result to fit in the available bits Step7. Checking for underflow/overflow occurrence Implementation of Hardware Floating Point multiplication The black box view of floating point multiplier is shown in figure 2. Paper ijgis.com OCTOBER/2014 Page 236
3 The Bias is subtracted using an array of ripple borrow subtractors. A normal subtractor has three inputs (minuend (S), subtrahend (T), Borrow in (Bi)) and two outputs (Difference (R), Borrow out (B)). The subtractor logic can be optimized if one of its inputs is a constant value which is our case, where the Bias is constant ( = ).Table I shows the truth table for a 1-bit subtractor with the input T equal to 1 which we will call one subtractor (OS). Table II shows the truth table for a 1-bit subtractor with the input T equal to 0 which we will call zero subtractor (ZS). Figure2. Block box view of floating point multiplier Sign bit calculation Multiplying two numbers results in a negative sign number if one of the multiplied numbers is of a negative value. By the aid of a truth table we find that this can be obtained by XORing the sign of two inputs Exponent addition This unsigned adder is responsible for adding the exponent of the first input to the exponent of the second input and subtracting the Bias (1023) from the addition result (i.e. A_exponent + B_exponent -Bias). The result of this stage is called the intermediate exponent. The add operation is done on 8 bits, and there is no need for a quick result because most of the calculation time is spent in the significand multiplication process (multiplying 53 adder and a fast significand multiplier. An 11-bit ripple carry adder is used to add the two input exponents. As shown in Figure 3 a ripple carry adder is a chain of cascaded full adders and one half adder; each full adder has three inputs (A, B, Ci) and two outputs (S, C). The carry out (C) of each adder is fed to the next full adder (i.e each carry bit "ripples" to the next full adder). The addition process produces an 11 bit sum (S10 to S0) and a carry bit (C11). These bits are concatenated to form a 12 bit addition result (S12 to S0) from which the Bias is subtracted. Figure3. Ripple carry adder Exponent subtraction Table I S T Bi Difference (R) B Table II S T Bi Difference(R) B Figure 4 shows the Bias subtractor which is a chain of 10 one subtractors (OS) followed by 2 zero subtractors (ZS); the borrow output of each subtractor is fed to the next subtractor. If an underflow occurs then Eresult < 0 and the number is out of the IEEE 754 single precision normalized numbers range; in this case the output is signaled to 0 and an underflow flag is asserted. Figure4. Ripple Borrow Subtractor 3.3. Dadda multiplier The multiplication process begins with the generation of all partial products in parallel using an array of AND gates. The next major steps in the design process are partitioning of the partial products and their reduction process. Each of these steps is elaborated in the following subsections Partitioning the partial products We consider two n-bit operands an-1an-2 a2a1a0 and bn- 1bn-2 b2b1b0 for n by n Baugh-Wooley multiplier, the partial products of two n-bit numbers are aibj where i,j go from 0,1,..n-1. The partial products form a matrix of n rows and 2n-1 columns as show in Fig. 1(a). To each partial product we assign a number as shown in Fig. 1 (a), e.g. a0b0 Paper ijgis.com OCTOBER/2014 Page 237
4 is given an index 0, a1b0 the index 1 and so on. For convenience we rearrange the partial products as shown in Fig 1(b). The longest column in the middle of the partial products contributes to the maximum delay in the PPST. Therefore in this work we split-up the PPST into two parts as shown in the Fig. 1(c), in which the Part0 and part1 consists of n columns. We then proceed to sum up each column of the two parts in parallel. The summation procedure adopted in this work is described in the next section The Dadda based reduction Next the partial products of each part are reduced to two rows by the using (3,2) and (2,2) counters based on the regular Dadda reduction algorithm as shown in Fig. 2 and Fig. 3. The grouping of 3-bits and 2-bits indicates (3,2) and (2,2) counters respectively and the different colors classify the difference between each column, where s and c denote partial sum and partial carry respectively. E.g. the bit positions of 6 and 13 in part0 are added using a (2,2) counter to generate sum s0 and c0. The c0 is carried to the next column where it is to be added up with the sum s1 of a (3,2) counter adding 7, 14 and 21. The carry c1 of (3,2) counter is added to the next column. The final two rows of each part are summed using a Carry Look-ahead Adder (CLA) to form the partial final products of a height of one bit column which indicated at the bottom of Fig. 3 and Fig. 4. The two parallel structures for Fig. 3 and Fig. 4 based on the Dadda approach are shown in Fig. 4, where HA, FA, p0, p1 and p denote Half Adder ((2,2)counter)), Full Adder ((3,2)counter), partial final product from part0, partial final product from part1 and final product respectively. The numerals residing on the HA and FA indicates the position of partial products. The output of part0 and part1 are computed independently in parallel and those values are added using a high speed hybrid final adder to get the final product. However, before we proceed to carry out the final addition with the proposed hybrid adder, we first carry out the final addition with the CLA for both the unpartitioned Dadda multiplier and the partitioned Dadda multiplier. This enables us to evaluate and analyze the effect of partitioning the PPST into two parts. It can be seen that for the 8-bit multiplier, there is no improvement in the speed, area and power. But with the increase in the word size, the improvement in the speed, area and power of the partitioned multipliers increases. There is a maximum of 10.5% improvement in delay for the 64-bit multiplier with only a slight increase in the area and power of 1% and 1.8% respectively. Having clearly demonstrated the reduction in the delay of the Dadda multipliers due to the partitioning of the partial products we now proceed to further enhance the speed of the proposed multiplier. IV. UNDERFLOW/OVERFLOW DETECTION Overflow/underflow means that the result s exponent is too large/small to be represented in the exponent field. The exponent of the result must be 11 bits in size, and must be between 1 and 2046 otherwise the value is not a normalized one. An overflow may occur while adding the double precision floating point multiplier code was a checked using Design Xilinx targeting on Sartan-6. Figure 5 shows the simulation results of high speed double precision floating point multiplier of the bias; resulting in a normal output value (normal operation). An underflow may occur while subtracting the bias to form the intermediate exponent. If the intermediate exponent < 0 then it s an underflow that can never be compensated. If the intermediate exponent = 0 then it s an underflow that may be compensated during by adding 1 to it. Table III shows the effect on result s exponent and overflow/underflow detection. Table III E result Underflow Can t compensated be During E result =0 Zero May turn to normalized number During 1 E result 2046 Normalized number May result in overflowduring 2047 E result Overflow Can t be compensated When an overflow occurs an overflow flag signal goes high and the result turns to ±Infinity (sign determined according to the sign of the floating point multiplier inputs). When an underflow occurs an underflow flag signal goes high and the result turns to ±Zero (sign determined according to the sign of the floating point multiplier inputs). De normalized numbers are signaled to Zero with the appropriate sign calculated from the inputs and an underflow flag is raised. Assume that E1 and E2 are the exponents of the two numbers A and B respectively the results exponent is calculated by (1). E result = E1 + E (1) E1 and E2 can have the values from 1 to 2046; resulting in E result having values from (2-1023) to 3069 ( ); but for normalized numbers, Eresult can only have the values from 1 to V. SIMULATION RESULTS The whole multiplier (top unit) was tested against the Xilinx floating point multiplier core generated by Xilinx core and an efficient implementation of floating point multiplier in. Xilinx core and multiplier in was customized to have two flags to indicate overflow and underflow, and to have a maximum latency of three cycles. Xilinx core implements the round to nearest rounding mode but multiplier doesn t support rounding modes. A test bench is used to generate the stimulus and applies it to the high speed Paper ijgis.com OCTOBER/2014 Page 238
5 double precision floating point. International Journal Of Global Innovations -Vol.1, Issue.II Johnson, Implementation of IEEE Single Precision Floating Point Addition and Multiplication on FPGAs, Proceedings of 83 the IEEE Symposium on FPGAs for Custom Computing Machines (FCCM 96), pp , [8] John G. Proakis and Dimitris G. Manolakis (1996), Digital Signal Processing: Principles,.Algorithms and Applications, Third Edition. [9] N. Shirazi, A. Walters, and P.Athanas, Quantitative Analysis of Floating Point Arithmetic on FPGA Based Custom Computing Machines, Proceedings of the IEEE Symposium on FPGAs for Custom Computing Machines (FCCM 95), pp , [10] B. Fagin and C. Renard, Field Programmable Gate Arrays and Floating Point Arithmetic, IEEE Transactions on VLSI, vol. 2, no. 3, pp , Figure5. Simulation results of high speed double precision floating point multiplier. VI. CONCLUSION The double precision floating point adder/subtractor and multiplier supports the IEEE-754 binary interchange format, targeted on a Xilinx Spartan-6 FPGA. The designs achieved the operating frequencies of MHz and MFLOPs with an area of 660 and 648 slices respectively. The adder/subtractor design operates at a frequency which is 3% and 28% more compared to and Xilinx core respectively. As compared to the single precision floating point multiplier and Xilinx core, the multiplier design supports double precision, provides high speed and gives more accuracy. These designs handles the overflow, underflow, rounding mode and various exception conditions. REFERENCES [1] M.Al-Ashrafy, A.Salem and W.Anis, An Efficient Implementation of Floating Point Multiplier Electronics Communications and Photonics Conference(SIECPC) 2011 Saudi International, pp.1-5,2011. [2] F.de Dinechin and B.Pasca. Large multipliers with fewer DSP blocks.in Field Pro- grammable Logic and Applications. IEEE, Aug [3] IEEE , IEEE Standard for Floating-Point Arithmetic, [4] Patterson, D. & Hennessy, J. (2005), computer Organization and Design : The Hardware/software Interface, Morgan Kaufmann. [5] B. Lee and N. Burgess, Parameterisable Floatingpoint Operations on FPGA, Conference Record of the Thirty-Sixth Asilomar Conference on Signals, Systems, and Computers, 2002 [6] A. Jaenicke and W.Luk, "Parameterized Floating- Point Arithmetic on FPGAs", Proc. of IEEE ICASSP, 2001, vol. 2, pp [7]L. Louca, T. A. Cook, and W.H. Paper ijgis.com OCTOBER/2014 Page 239
IJCSIET--International Journal of Computer Science information and Engg., Technologies ISSN
FPGA Implementation of 64 Bit Floating Point Multiplier Using DADDA Algorithm Priyanka Saxena *1, Ms. Imthiyazunnisa Begum *2 M. Tech (VLSI System Design), Department of ECE, VIFCET, Gandipet, Telangana,
More informationAn Efficient Implementation of Floating Point Multiplier
An Efficient Implementation of Floating Point Multiplier Mohamed Al-Ashrafy Mentor Graphics Mohamed_Samy@Mentor.com Ashraf Salem Mentor Graphics Ashraf_Salem@Mentor.com Wagdy Anis Communications and Electronics
More informationA High Speed Binary Floating Point Multiplier Using Dadda Algorithm
455 A High Speed Binary Floating Point Multiplier Using Dadda Algorithm B. Jeevan, Asst. Professor, Dept. of E&IE, KITS, Warangal. jeevanbs776@gmail.com S. Narender, M.Tech (VLSI&ES), KITS, Warangal. narender.s446@gmail.com
More informationImplementation of Floating Point Multiplier Using Dadda Algorithm
Implementation of Floating Point Multiplier Using Dadda Algorithm Abstract: Floating point multiplication is the most usefull in all the computation application like in Arithematic operation, DSP application.
More informationInternational Journal of Research in Computer and Communication Technology, Vol 4, Issue 11, November- 2015
Design of Dadda Algorithm based Floating Point Multiplier A. Bhanu Swetha. PG.Scholar: M.Tech(VLSISD), Department of ECE, BVCITS, Batlapalem. E.mail:swetha.appari@gmail.com V.Ramoji, Asst.Professor, Department
More informationFigurel. TEEE-754 double precision floating point format. Keywords- Double precision, Floating point, Multiplier,FPGA,IEEE-754.
AN FPGA BASED HIGH SPEED DOUBLE PRECISION FLOATING POINT MULTIPLIER USING VERILOG N.GIRIPRASAD (1), K.MADHAVA RAO (2) VLSI System Design,Tudi Ramireddy Institute of Technology & Sciences (1) Asst.Prof.,
More informationDevelopment of an FPGA based high speed single precision floating point multiplier
International Journal of Electronic and Electrical Engineering. ISSN 0974-2174 Volume 8, Number 1 (2015), pp. 27-32 International Research Publication House http://www.irphouse.com Development of an FPGA
More informationInternational Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering
An Efficient Implementation of Double Precision Floating Point Multiplier Using Booth Algorithm Pallavi Ramteke 1, Dr. N. N. Mhala 2, Prof. P. R. Lakhe M.Tech [IV Sem], Dept. of Comm. Engg., S.D.C.E, [Selukate],
More informationAn FPGA Based Floating Point Arithmetic Unit Using Verilog
An FPGA Based Floating Point Arithmetic Unit Using Verilog T. Ramesh 1 G. Koteshwar Rao 2 1PG Scholar, Vaagdevi College of Engineering, Telangana. 2Assistant Professor, Vaagdevi College of Engineering,
More informationImplementation of Double Precision Floating Point Multiplier in VHDL
ISSN (O): 2349-7084 International Journal of Computer Engineering In Research Trends Available online at: www.ijcert.org Implementation of Double Precision Floating Point Multiplier in VHDL 1 SUNKARA YAMUNA
More informationAn Implementation of Double precision Floating point Adder & Subtractor Using Verilog
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 9, Issue 4 Ver. III (Jul Aug. 2014), PP 01-05 An Implementation of Double precision Floating
More informationTHE INTERNATIONAL JOURNAL OF SCIENCE & TECHNOLEDGE
THE INTERNATIONAL JOURNAL OF SCIENCE & TECHNOLEDGE Design and Implementation of Optimized Floating Point Matrix Multiplier Based on FPGA Maruti L. Doddamani IV Semester, M.Tech (Digital Electronics), Department
More informationImplementation of IEEE-754 Double Precision Floating Point Multiplier
Implementation of IEEE-754 Double Precision Floating Point Multiplier G.Lakshmi, M.Tech Lecturer, Dept of ECE S K University College of Engineering Anantapuramu, Andhra Pradesh, India ABSTRACT: Floating
More informationFPGA Implementation of Low-Area Floating Point Multiplier Using Vedic Mathematics
FPGA Implementation of Low-Area Floating Point Multiplier Using Vedic Mathematics R. Sai Siva Teja 1, A. Madhusudhan 2 1 M.Tech Student, 2 Assistant Professor, Dept of ECE, Anurag Group of Institutions
More informationImplementation of Double Precision Floating Point Multiplier on FPGA
Implementation of Double Precision Floating Point Multiplier on FPGA A.Keerthi 1, K.V.Koteswararao 2 PG Student [VLSI], Dept. of ECE, Sree Vidyanikethan Engineering College, Tirupati, India 1 Assistant
More informationA Novel Efficient VLSI Architecture for IEEE 754 Floating point multiplier using Modified CSA
RESEARCH ARTICLE OPEN ACCESS A Novel Efficient VLSI Architecture for IEEE 754 Floating point multiplier using Nishi Pandey, Virendra Singh Sagar Institute of Research & Technology Bhopal Abstract Due to
More informationComparison of Adders for optimized Exponent Addition circuit in IEEE754 Floating point multiplier using VHDL
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 11, Issue 07 (July 2015), PP.60-65 Comparison of Adders for optimized Exponent Addition
More informationAn FPGA based Implementation of Floating-point Multiplier
An FPGA based Implementation of Floating-point Multiplier L. Rajesh, Prashant.V. Joshi and Dr.S.S. Manvi Abstract In this paper we describe the parameterization, implementation and evaluation of floating-point
More informationDesign and Implementation of Floating Point Multiplier for Better Timing Performance
Design and Implementation of Floating Point Multiplier for Better Timing Performance B.Sreenivasa Ganesh 1,J.E.N.Abhilash 2, G. Rajesh Kumar 3 SwarnandhraCollege of Engineering& Technology 1,2, Vishnu
More informationPipelined High Speed Double Precision Floating Point Multiplier Using Dadda Algorithm Based on FPGA
RESEARCH ARTICLE OPEN ACCESS Pipelined High Speed Double Precision Floating Point Multiplier Using Dadda Algorithm Based on FPGA J.Rupesh Kumar, G.Ram Mohan, Sudershanraju.Ch M. Tech Scholar, Dept. of
More informationCOMPARISION OF PARALLEL BCD MULTIPLICATION IN LUT-6 FPGA AND 64-BIT FLOTING POINT ARITHMATIC USING VHDL
COMPARISION OF PARALLEL BCD MULTIPLICATION IN LUT-6 FPGA AND 64-BIT FLOTING POINT ARITHMATIC USING VHDL Mrs. Vibha Mishra M Tech (Embedded System And VLSI Design) GGITS,Jabalpur Prof. Vinod Kapse Head
More informationVHDL IMPLEMENTATION OF FLOATING POINT MULTIPLIER USING VEDIC MATHEMATICS
VHDL IMPLEMENTATION OF FLOATING POINT MULTIPLIER USING VEDIC MATHEMATICS I.V.VAIBHAV 1, K.V.SAICHARAN 1, B.SRAVANTHI 1, D.SRINIVASULU 2 1 Students of Department of ECE,SACET, Chirala, AP, India 2 Associate
More informationISSN Vol.03,Issue.11, December-2015, Pages:
WWW.IJITECH.ORG ISSN 2321-8665 Vol.03,Issue.11, December-2015, Pages:2107-2112 An Efficient Implementation of Floating Point Multiplier using Verilog G. SRUTHI 1, M. RAJENDRA PRASAD 2 1 PG Scholar, Dept
More informationUniversity, Patiala, Punjab, India 1 2
1102 Design and Implementation of Efficient Adder based Floating Point Multiplier LOKESH BHARDWAJ 1, SAKSHI BAJAJ 2 1 Student, M.tech, VLSI, 2 Assistant Professor,Electronics and Communication Engineering
More informationINTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY
INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK DESIGN AND VERIFICATION OF FAST 32 BIT BINARY FLOATING POINT MULTIPLIER BY INCREASING
More informationA comparative study of Floating Point Multipliers Using Ripple Carry Adder and Carry Look Ahead Adder
A comparative study of Floating Point Multipliers Using Ripple Carry Adder and Carry Look Ahead Adder 1 Jaidev Dalvi, 2 Shreya Mahajan, 3 Saya Mogra, 4 Akanksha Warrier, 5 Darshana Sankhe 1,2,3,4,5 Department
More informationDesign and Implementation of IEEE-754 Decimal Floating Point Adder, Subtractor and Multiplier
International Journal of Engineering and Advanced Technology (IJEAT) ISSN: 2249 8958, Volume-4 Issue 1, October 2014 Design and Implementation of IEEE-754 Decimal Floating Point Adder, Subtractor and Multiplier
More information2 Prof, Dept of ECE, VNR Vignana Jyothi Institute of Engineering & Technology, A.P-India,
www.semargroups.org, www.ijsetr.com ISSN 2319-8885 Vol.02,Issue.17, November-2013, Pages:2017-2027 An Efficient Implementation of Floating Pont Multiplier Using Vedic Mathematics D. SRIDEVI 1, DR. L. PADMASREE
More informationA Library of Parameterized Floating-point Modules and Their Use
A Library of Parameterized Floating-point Modules and Their Use Pavle Belanović and Miriam Leeser Department of Electrical and Computer Engineering Northeastern University Boston, MA, 02115, USA {pbelanov,mel}@ece.neu.edu
More informationRun-Time Reconfigurable multi-precision floating point multiplier design based on pipelining technique using Karatsuba-Urdhva algorithms
Run-Time Reconfigurable multi-precision floating point multiplier design based on pipelining technique using Karatsuba-Urdhva algorithms 1 Shruthi K.H., 2 Rekha M.G. 1M.Tech, VLSI design and embedded system,
More informationInternational Journal of Advanced Research in Computer Science and Software Engineering
ISSN: 2277 128X International Journal of Advanced Research in Computer Science and Software Engineering Research Paper Available online at: Configuring Floating Point Multiplier on Spartan 2E Hardware
More informationDesign and Analysis of Inexact Floating Point Multipliers
Design and Analysis of Inexact Floating Point Multipliers Jogadenu Vedavathi 1 Mrs.T.Nagalaxmi 2 jogadenuvedavathi1993@gmail.com 1 tnagalaxmi@stanley.edu.in 2 1 PG Scholar, Dept of ECE, Stanley College
More informationInternational Journal of Advanced Research in Computer Science and Software Engineering
ISSN: 2277 128X International Journal of Advanced Research in Computer Science and Software Engineering Research Paper Available online at: Implementation of Floating Point Multiplier on Reconfigurable
More informationImplementation of a High Speed Binary Floating point Multiplier Using Dadda Algorithm in FPGA
Implementation of a High Speed Binary Floating point Multiplier Using Dadda Algorithm in FPGA Ms.Komal N.Batra 1, Prof. Ashish B. Kharate 2 1 PG Student, ENTC Department, HVPM S College of Engineering
More informationPrinciples of Computer Architecture. Chapter 3: Arithmetic
3-1 Chapter 3 - Arithmetic Principles of Computer Architecture Miles Murdocca and Vincent Heuring Chapter 3: Arithmetic 3-2 Chapter 3 - Arithmetic 3.1 Overview Chapter Contents 3.2 Fixed Point Addition
More informationArchitecture and Design of Generic IEEE-754 Based Floating Point Adder, Subtractor and Multiplier
Architecture and Design of Generic IEEE-754 Based Floating Point Adder, Subtractor and Multiplier Sahdev D. Kanjariya VLSI & Embedded Systems Design Gujarat Technological University PG School Ahmedabad,
More informationDouble Precision Floating-Point Arithmetic on FPGAs
MITSUBISHI ELECTRIC ITE VI-Lab Title: Double Precision Floating-Point Arithmetic on FPGAs Internal Reference: Publication Date: VIL04-D098 Author: S. Paschalakis, P. Lee Rev. A Dec. 2003 Reference: Paschalakis,
More informationFPGA Implementation of a High Speed Multiplier Employing Carry Lookahead Adders in Reduction Phase
FPGA Implementation of a High Speed Multiplier Employing Carry Lookahead Adders in Reduction Phase Abhay Sharma M.Tech Student Department of ECE MNNIT Allahabad, India ABSTRACT Tree Multipliers are frequently
More informationDesign of Double Precision Floating Point Multiplier Using Vedic Multiplication
Design of Double Precision Floating Point Multiplier Using Vedic Multiplication 1 D.Heena Tabassum, 2 K.Sreenivas Rao 1, 2 Electronics and Communication Engineering, 1, 2 Annamacharya institute of technology
More informationFPGA Implementation of Multiplier for Floating- Point Numbers Based on IEEE Standard
FPGA Implementation of Multiplier for Floating- Point Numbers Based on IEEE 754-2008 Standard M. Shyamsi, M. I. Ibrahimy, S. M. A. Motakabber and M. R. Ahsan Dept. of Electrical and Computer Engineering
More informationComputer Architecture and Organization
3-1 Chapter 3 - Arithmetic Computer Architecture and Organization Miles Murdocca and Vincent Heuring Chapter 3 Arithmetic 3-2 Chapter 3 - Arithmetic Chapter Contents 3.1 Fixed Point Addition and Subtraction
More informationImplementation of Double Precision Floating Point Multiplier Using Wallace Tree Multiplier
Implementation of Double Precision Floating Point Multiplier Using Wallace Tree Multiplier Y. Ramya sri 1, V B K L Aruna 2 P.G. Student, Department of Electronics Engineering, V.R Siddhartha Engineering
More informationFPGA based High Speed Double Precision Floating Point Divider
FPGA based High Speed Double Precision Floating Point Divider Addanki Purna Ramesh Department of ECE, Sri Vasavi Engineering College, Pedatadepalli, Tadepalligudem, India. Dhanalakshmi Balusu Department
More informationVendor Agnostic, High Performance, Double Precision Floating Point Division for FPGAs
Vendor Agnostic, High Performance, Double Precision Floating Point Division for FPGAs Xin Fang and Miriam Leeser Dept of Electrical and Computer Eng Northeastern University Boston, Massachusetts 02115
More informationISSN Vol.02, Issue.11, December-2014, Pages:
ISSN 2322-0929 Vol.02, Issue.11, December-2014, Pages:1208-1212 www.ijvdcs.org Implementation of Area Optimized Floating Point Unit using Verilog G.RAJA SEKHAR 1, M.SRIHARI 2 1 PG Scholar, Dept of ECE,
More informationIEEE-754 compliant Algorithms for Fast Multiplication of Double Precision Floating Point Numbers
International Journal of Research in Computer Science ISSN 2249-8257 Volume 1 Issue 1 (2011) pp. 1-7 White Globe Publications www.ijorcs.org IEEE-754 compliant Algorithms for Fast Multiplication of Double
More information16 BIT IMPLEMENTATION OF ASYNCHRONOUS TWOS COMPLEMENT ARRAY MULTIPLIER USING MODIFIED BAUGH-WOOLEY ALGORITHM AND ARCHITECTURE.
16 BIT IMPLEMENTATION OF ASYNCHRONOUS TWOS COMPLEMENT ARRAY MULTIPLIER USING MODIFIED BAUGH-WOOLEY ALGORITHM AND ARCHITECTURE. AditiPandey* Electronics & Communication,University Institute of Technology,
More informationFPGA Implementation of Single Precision Floating Point Multiplier Using High Speed Compressors
2018 IJSRST Volume 4 Issue 2 Print ISSN: 2395-6011 Online ISSN: 2395-602X Themed Section: Science and Technology FPGA Implementation of Single Precision Floating Point Multiplier Using High Speed Compressors
More information(+A) + ( B) + (A B) (B A) + (A B) ( A) + (+ B) (A B) + (B A) + (A B) (+ A) (+ B) + (A - B) (B A) + (A B) ( A) ( B) (A B) + (B A) + (A B)
COMPUTER ARITHMETIC 1. Addition and Subtraction of Unsigned Numbers The direct method of subtraction taught in elementary schools uses the borrowconcept. In this method we borrow a 1 from a higher significant
More informationChapter 3: part 3 Binary Subtraction
Chapter 3: part 3 Binary Subtraction Iterative combinational circuits Binary adders Half and full adders Ripple carry and carry lookahead adders Binary subtraction Binary adder-subtractors Signed binary
More informationDESIGN TRADEOFF ANALYSIS OF FLOATING-POINT. ADDER IN FPGAs
DESIGN TRADEOFF ANALYSIS OF FLOATING-POINT ADDER IN FPGAs A Thesis Submitted to the College of Graduate Studies and Research In Partial Fulfillment of the Requirements For the Degree of Master of Science
More informationFloating-Point Matrix Product on FPGA
Floating-Point Matrix Product on FPGA Faycal Bensaali University of Hertfordshire f.bensaali@herts.ac.uk Abbes Amira Brunel University abbes.amira@brunel.ac.uk Reza Sotudeh University of Hertfordshire
More informationAn Efficient Fused Add Multiplier With MWT Multiplier And Spanning Tree Adder
An Efficient Fused Add Multiplier With MWT Multiplier And Spanning Tree Adder 1.M.Megha,M.Tech (VLSI&ES),2. Nataraj, M.Tech (VLSI&ES), Assistant Professor, 1,2. ECE Department,ST.MARY S College of Engineering
More informationDesign and Implementation of Signed, Rounded and Truncated Multipliers using Modified Booth Algorithm for Dsp Systems.
Design and Implementation of Signed, Rounded and Truncated Multipliers using Modified Booth Algorithm for Dsp Systems. K. Ram Prakash 1, A.V.Sanju 2 1 Professor, 2 PG scholar, Department of Electronics
More informationEE878 Special Topics in VLSI. Computer Arithmetic for Digital Signal Processing
EE878 Special Topics in VLSI Computer Arithmetic for Digital Signal Processing Part 6b High-Speed Multiplication - II Spring 2017 Koren Part.6b.1 Accumulating the Partial Products After generating partial
More informationReview on Floating Point Adder and Converter Units Using VHDL
Review on Floating Point Adder and Converter Units Using VHDL Abhishek Kumar 1, Mayur S. Dhait 2 1 Research Scholar, Agnihotri College of Engineering, Nagthana Road, Wardha (M.S), India 2 Professor, Department
More informationUNIVERSITY OF MASSACHUSETTS Dept. of Electrical & Computer Engineering. Digital Computer Arithmetic ECE 666
UNIVERSITY OF MASSACHUSETTS Dept. of Electrical & Computer Engineering Digital Computer Arithmetic ECE 666 Part 6b High-Speed Multiplication - II Israel Koren ECE666/Koren Part.6b.1 Accumulating the Partial
More informationFig.1. Floating point number representation of single-precision (32-bit). Floating point number representation in double-precision (64-bit) format:
1313 DESIGN AND PERFORMANCE ANALYSIS OF DOUBLE- PRECISION FLOATING POINT MULTIPLIER USING URDHVA TIRYAGBHYAM SUTRA Y SRINIVASA RAO 1, T SUBHASHINI 2, K RAMBABU 3 P.G Student 1, Assistant Professor 2, Assistant
More informationImplementation of Efficient Modified Booth Recoder for Fused Sum-Product Operator
Implementation of Efficient Modified Booth Recoder for Fused Sum-Product Operator A.Sindhu 1, K.PriyaMeenakshi 2 PG Student [VLSI], Dept. of ECE, Muthayammal Engineering College, Rasipuram, Tamil Nadu,
More informationOPTIMIZING THE POWER USING FUSED ADD MULTIPLIER
Available Online at www.ijcsmc.com International Journal of Computer Science and Mobile Computing A Monthly Journal of Computer Science and Information Technology IJCSMC, Vol. 3, Issue. 11, November 2014,
More informationPartitioned Branch Condition Resolution Logic
1 Synopsys Inc. Synopsys Module Compiler Group 700 Middlefield Road, Mountain View CA 94043-4033 (650) 584-5689 (650) 584-1227 FAX aamirf@synopsys.com http://aamir.homepage.com Partitioned Branch Condition
More informationFFT REPRESENTATION USING FLOATING- POINT BUTTERFLY ARCHITECTURE
FFT REPRESENTATION USING FLOATING- POINT BUTTERFLY ARCHITECTURE 1 Mr.S. BHARATH KUMAR, 2 Mr.P. VENKATESWARLU, 3 Dr. Mr. ARVIND KUNDU 1 PG Student, 2 Assistant professor, 3 Associate Professor 1 Department
More informationCOMPUTER ARCHITECTURE AND ORGANIZATION. Operation Add Magnitudes Subtract Magnitudes (+A) + ( B) + (A B) (B A) + (A B)
Computer Arithmetic Data is manipulated by using the arithmetic instructions in digital computers. Data is manipulated to produce results necessary to give solution for the computation problems. The Addition,
More informationVLSI Implementation of High Speed and Area Efficient Double-Precision Floating Point Multiplier
VLSI Implementation of High Speed and Area Efficient Double-Precision Floating Point Ramireddy Venkata Suresh 1, K.Bala 2 1 M.Tech, Dept of ECE, Srinivasa Institute of Technology and Science, Ukkayapalli,
More informationImplementation of Double Precision Floating Point Adder with Residue for High Accuracy Using FPGA
1008 Implementation of Double Precision Floating Point Adder with Residue for High Accuracy Using FPGA P.V.V.S. Narayana 1, N.V.N. Prasanna Kumar 2 1 (M.Tech Student, Department of ECE, Sri Vasavi Engineering
More informationA Survey on Floating Point Adders
A Survey on Floating Point Adders Geetanjali Sharma 1, Neetesh Dodkey 2 1 Dept. of Electronics and Communication Engineering Surbhi group of Institue, India 21geetanjali@gmail.com 2 Dept. of Electronics
More informationJOURNAL OF INTERNATIONAL ACADEMIC RESEARCH FOR MULTIDISCIPLINARY Impact Factor 1.393, ISSN: , Volume 2, Issue 7, August 2014
DESIGN OF HIGH SPEED BOOTH ENCODED MULTIPLIER PRAVEENA KAKARLA* *Assistant Professor, Dept. of ECONE, Sree Vidyanikethan Engineering College, A.P., India ABSTRACT This paper presents the design and implementation
More informationPipelined Quadratic Equation based Novel Multiplication Method for Cryptographic Applications
, Vol 7(4S), 34 39, April 204 ISSN (Print): 0974-6846 ISSN (Online) : 0974-5645 Pipelined Quadratic Equation based Novel Multiplication Method for Cryptographic Applications B. Vignesh *, K. P. Sridhar
More informationVTU NOTES QUESTION PAPERS NEWS RESULTS FORUMS Arithmetic (a) The four possible cases Carry (b) Truth table x y
Arithmetic A basic operation in all digital computers is the addition and subtraction of two numbers They are implemented, along with the basic logic functions such as AND,OR, NOT,EX- OR in the ALU subsystem
More informationVARUN AGGARWAL
ECE 645 PROJECT SPECIFICATION -------------- Design A Microprocessor Functional Unit Able To Perform Multiplication & Division Professor: Students: KRIS GAJ LUU PHAM VARUN AGGARWAL GMU Mar. 2002 CONTENTS
More informationAnalysis of High-performance Floating-point Arithmetic on FPGAs
Analysis of High-performance Floating-point Arithmetic on FPGAs Gokul Govindu, Ling Zhuo, Seonil Choi and Viktor Prasanna Dept. of Electrical Engineering University of Southern California Los Angeles,
More informationA Decimal Floating Point Arithmetic Unit for Embedded System Applications using VLSI Techniques
A Decimal Floating Point Arithmetic Unit for Embedded System Applications using VLSI Techniques Rajeshwari Mathapati #1, Shrikant. K.Shirakol *2 # Dept of E&CE, S.D.M. College of Engg. and Tech., Dharwad,
More informationIMPLEMENTATION OF DOUBLE PRECISION FLOATING POINT RADIX-2 FFT USING VHDL
IMPLEMENTATION OF DOUBLE PRECISION FLOATING POINT RADIX-2 FFT USING VHDL Tharanidevi.B 1, Jayaprakash.R 2 Assistant Professor, Dept. of ECE, Bharathiyar Institute of Engineering for Woman, Salem, TamilNadu,
More informationOptimized Design and Implementation of a 16-bit Iterative Logarithmic Multiplier
Optimized Design and Implementation a 16-bit Iterative Logarithmic Multiplier Laxmi Kosta 1, Jaspreet Hora 2, Rupa Tomaskar 3 1 Lecturer, Department Electronic & Telecommunication Engineering, RGCER, Nagpur,India,
More informationBinary Adders: Half Adders and Full Adders
Binary Adders: Half Adders and Full Adders In this set of slides, we present the two basic types of adders: 1. Half adders, and 2. Full adders. Each type of adder functions to add two binary bits. In order
More informationDouble Precision IEEE-754 Floating-Point Adder Design Based on FPGA
Double Precision IEEE-754 Floating-Point Adder Design Based on FPGA Adarsha KM 1, Ashwini SS 2, Dr. MZ Kurian 3 PG Student [VLS& ES], Dept. of ECE, Sri Siddhartha Institute of Technology, Tumkur, Karnataka,
More informationHIGH SPEED SINGLE PRECISION FLOATING POINT UNIT IMPLEMENTATION USING VERILOG
HIGH SPEED SINGLE PRECISION FLOATING POINT UNIT IMPLEMENTATION USING VERILOG 1 C.RAMI REDDY, 2 O.HOMA KESAV, 3 A.MAHESWARA REDDY 1 PG Scholar, Dept of ECE, AITS, Kadapa, AP-INDIA. 2 Asst Prof, Dept of
More information32-bit Signed and Unsigned Advanced Modified Booth Multiplication using Radix-4 Encoding Algorithm
2016 IJSRSET Volume 2 Issue 3 Print ISSN : 2395-1990 Online ISSN : 2394-4099 Themed Section: Engineering and Technology 32-bit Signed and Unsigned Advanced Modified Booth Multiplication using Radix-4 Encoding
More informationISSN: X Impact factor: (Volume3, Issue2) Analyzing Two-Term Dot Product of Multiplier Using Floating Point and Booth Multiplier
ISSN: 2454-132X Impact factor: 4.295 (Volume3, Issue2) Analyzing Two-Term Dot Product of Multiplier Using Floating Point and Booth Multiplier 1 Mukesh Krishna Department Electrical and Electronics Engineering
More informationNeelesh Thakur, 2 Rama Pandole Dept. of Electronics and Communication Engineering Kailash narayan patidar college of science and technology, India
Review on Different Floating Point Adders VOLUME 2 ISSUE 7 www.ijatser.com 1 Neelesh Thakur, 2 Rama Pandole Dept. of Electronics and Communication Engineering Kailash narayan patidar college of science
More informationECE 2030B 1:00pm Computer Engineering Spring problems, 5 pages Exam Two 10 March 2010
Instructions: This is a closed book, closed note exam. Calculators are not permitted. If you have a question, raise your hand and I will come to you. Please work the exam in pencil and do not separate
More informationImplementation of IEEE754 Floating Point Multiplier
Implementation of IEEE754 Floating Point Multiplier A Kumutha 1 Shobha. P 2 1 MVJ College of Engineering, Near ITPB, Channasandra, Bangalore-67. 2 MVJ College of Engineering, Near ITPB, Channasandra, Bangalore-67.
More informationChapter 4 Arithmetic Functions
Logic and Computer Design Fundamentals Chapter 4 Arithmetic Functions Charles Kime & Thomas Kaminski 2008 Pearson Education, Inc. (Hyperlinks are active in View Show mode) Overview Iterative combinational
More informationInternational Journal Of Global Innovations -Vol.6, Issue.II Paper Id: SP-V6-I1-P01 ISSN Online:
IMPLEMENTATION OF LOW POWER PIPELINED 64-BIT RISC PROCESSOR WITH DOUBLE PRECISION FLOATING POINT UNIT #1 CH.RAVALI, M.Tech student, #2 T.S.GAGANDEEP, Assistant Professor, Dept of ECE, DRK INSTITUTE OF
More informationInternational Journal of Computer Science Trends and Technology (IJCST) Volume 3 Issue 2, Mar-Apr 2015
RESEARCH ARTICLE A Survey on Floating Point Adders Deepak Mishra [1], Vipul Agrawal [2] Department of Electronics and Communication Engineering Trinity Institute of Technology & Research, Bhopal India
More informationVLSI Design Of a Novel Pre Encoding Multiplier Using DADDA Multiplier. Guntur(Dt),Pin:522017
VLSI Design Of a Novel Pre Encoding Multiplier Using DADDA Multiplier 1 Katakam Hemalatha,(M.Tech),Email Id: hema.spark2011@gmail.com 2 Kundurthi Ravi Kumar, M.Tech,Email Id: kundurthi.ravikumar@gmail.com
More informationAN EFFICIENT FLOATING-POINT MULTIPLIER DESIGN USING COMBINED BOOTH AND DADDA ALGORITHMS
AN EFFICIENT FLOATING-POINT MULTIPLIER DESIGN USING COMBINED BOOTH AND DADDA ALGORITHMS 1 DHANABAL R, BHARATHI V, 3 NAAMATHEERTHAM R SAMHITHA, 4 PAVITHRA S, 5 PRATHIBA S, 6 JISHIA EUGINE 1 Asst Prof. (Senior
More informationOPTIMIZATION OF AREA COMPLEXITY AND DELAY USING PRE-ENCODED NR4SD MULTIPLIER.
OPTIMIZATION OF AREA COMPLEXITY AND DELAY USING PRE-ENCODED NR4SD MULTIPLIER. A.Anusha 1 R.Basavaraju 2 anusha201093@gmail.com 1 basava430@gmail.com 2 1 PG Scholar, VLSI, Bharath Institute of Engineering
More informationAt the ith stage: Input: ci is the carry-in Output: si is the sum ci+1 carry-out to (i+1)st state
Chapter 4 xi yi Carry in ci Sum s i Carry out c i+ At the ith stage: Input: ci is the carry-in Output: si is the sum ci+ carry-out to (i+)st state si = xi yi ci + xi yi ci + xi yi ci + xi yi ci = x i yi
More informationFLOATING POINT ADDERS AND MULTIPLIERS
Concordia University FLOATING POINT ADDERS AND MULTIPLIERS 1 Concordia University Lecture #4 In this lecture we will go over the following concepts: 1) Floating Point Number representation 2) Accuracy
More informationDigital Computer Arithmetic
Digital Computer Arithmetic Part 6 High-Speed Multiplication Soo-Ik Chae Spring 2010 Koren Chap.6.1 Speeding Up Multiplication Multiplication involves 2 basic operations generation of partial products
More informationDesign of Delay Efficient Distributed Arithmetic Based Split Radix FFT
Design of Delay Efficient Arithmetic Based Split Radix FFT Nisha Laguri #1, K. Anusudha *2 #1 M.Tech Student, Electronics, Department of Electronics Engineering, Pondicherry University, Puducherry, India
More informationChapter 5 : Computer Arithmetic
Chapter 5 Computer Arithmetic Integer Representation: (Fixedpoint representation): An eight bit word can be represented the numbers from zero to 255 including = 1 = 1 11111111 = 255 In general if an nbit
More informationEvaluation of High Speed Hardware Multipliers - Fixed Point and Floating point
International Journal of Electrical and Computer Engineering (IJECE) Vol. 3, No. 6, December 2013, pp. 805~814 ISSN: 2088-8708 805 Evaluation of High Speed Hardware Multipliers - Fixed Point and Floating
More informationBy, Ajinkya Karande Adarsh Yoga
By, Ajinkya Karande Adarsh Yoga Introduction Early computer designers believed saving computer time and memory were more important than programmer time. Bug in the divide algorithm used in Intel chips.
More informationSum to Modified Booth Recoding Techniques For Efficient Design of the Fused Add-Multiply Operator
Sum to Modified Booth Recoding Techniques For Efficient Design of the Fused Add-Multiply Operator D.S. Vanaja 1, S. Sandeep 2 1 M. Tech scholar in VLSI System Design, Department of ECE, Sri VenkatesaPerumal
More informationADDERS AND MULTIPLIERS
Concordia University FLOATING POINT ADDERS AND MULTIPLIERS 1 Concordia University Lecture #4 In this lecture we will go over the following concepts: 1) Floating Point Number representation 2) Accuracy
More informationArea Efficient, Low Power Array Multiplier for Signed and Unsigned Number. Chapter 3
Area Efficient, Low Power Array Multiplier for Signed and Unsigned Number Chapter 3 Area Efficient, Low Power Array Multiplier for Signed and Unsigned Number Chapter 3 3.1 Introduction The various sections
More informationDESIGN OF DOUBLE PRECISION FLOATING POINT MULTIPLICATION ALGORITHM WITH VECTOR SUPPORT
DESIGN OF DOUBLE PRECISION FLOATING POINT MULTIPLICATION ALGORITHM WITH VECTOR SUPPORT T.Govinda Rao, P.Devi Pradeep, P.Kalyanchakravarthi Assistant Professor, Department of ECE, GMRIT, RAJAM, AP, INDIA
More informationECE 2030D Computer Engineering Spring problems, 5 pages Exam Two 8 March 2012
Instructions: This is a closed book, closed note exam. Calculators are not permitted. If you have a question, raise your hand and I will come to you. Please work the exam in pencil and do not separate
More information