PM Multifunction meter Cat No. F3N200 - ModbusTable BT EN v1.01.xls

Transcription

1 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls GENERAL MODBUS TABLE ORGANIZATION Starting of the Group s Starting of the Group s System Version (Release) System Version (Build) Group Name (Text) Group Code Group Complexity Group Version Customization specific data F040 D 0, C 676 8D50 Alarms F040 D 0, C 5052 C550 Measures - Metrology Affected by current and voltage transformers F040 D 0, C C650 Measures - Energies F040 D 0, C C6A0 Measures - Energies per tariff F040 D 0, C 5024 C750 Measures - Statistique Affected by current and voltage transformers F040 D 0, C Measures - Metrology No Affected by current and voltage transformers F040 D 0, C 5280 C C900 Measures - Temperatures F040 D 0, C 556 C950 Measure - Harmonic THD F040 D 0, C Reset F040 D 0, C 652 8E00 Table setup F040 D 0, C 5744 E000 Network Settings F040 D 0, C E200 Action System F040 D 0, C MODBUS PROTOCOL DETAILS Code Exception 0, 02, 0, 04, 05, 06, 07, , 02, 0, 04, 05, 06, 07, , 02, 0, 04, 05, 06, 07, 08 Encoding "Big Endian" (most significant byte first) MODBUS OVER SERIAL DETAILS Physical Layer Trasmission Modes Device ing Baud Rates (bit/s) Bits bits trasmission sequence Parity Stop Bits standard EIA/TIA 485 (RS-485) two-wire configuration RTU 247 programmable (2400, 4800, 9600, 9200, 8400) 8 Least significant bit first no, odd, even, 2 MASTER/SLAVE COMMUNICATION TIMING Timer Descrtiption Timer Value (msec) Inter-character time-out <,5 character times Response delay (from master request) - Delay Time (between two master trasmissions) - REFER ALSO TO: - MODBUS over serial line specification and implementation guide V.02 - MODBUS APPLICATION PROTOCOL SPECIFICATION V.b NOTE: File and printed copies of this document are not subject to document change control. File and printed copies of this document are not subject to document change control. Page /0

2 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls DISCRETE INPUT - Bits (R) [bit] Description Note Read (no DISCRETE INPUTS availables) File and printed copies of this document are not subject to document change control. Page 2/0

3 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls COILS - Bits (R&W) [bit] Description Note Read (no COILS availables) Write File and printed copies of this document are not subject to document change control. Page /0

4 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls INPUT REGISTERS - Words (R) Bit Position Description Type Scale Unit Range Note Read Code Customization specific data Customisation specific data loaded 0x0000 : FALSE 0x000 : TRUE Retrofit activated x0000 : FALSE 0x000 : TRUE TC list : TC / TC2 / TC / TC4 / TC5 / TC6 / TC7 / TC A 6 TC gain correction X 2 words = TC correction A 6 TC gain correction X2 2 words = TC correction A 6 TC gain correction Y 2 words = TC correction A 6 TC gain correction Y2 2 words = TC correction A 6 TC phasys correction X 2 words = TC correction A 6 TC phasys correction X2 2 words = TC correction A 6 TC phasys correction Y 2 words = TC correction A 6 TC phasys correction Y2 2 words = TC correction D50 7 Alarms Current alarm on lower threshold cause: 0 : No Alarm / : I / 2 : I2 / : I / 4 : IN / 5 : U2 / 6 : U2 / 7 : U / 8 : P+ / 9 : Q+ / 0 : S / D50 : F / 2 : PFL / 5: thdi / 6: thdi2 / 7 : thdi / 8 : thdu2 / 9 : thdu2 / 20 : thdu / 2 : Hour / 22: V / 2 : V2 / 24 : V / 26: thdv / 27 : thdv2 / 28 : thd V / : PFC / 2 : T C 0 : - / 2 / / 4 : ma 5 / 6 / 7 : mv 8 : mw 9 : mvar 0 : mva : Hz/000 2 : - 5 / 6 / 7 : /000 8 / 9 / 20 : /000 2 : Hour/00 22 / 2 / 24 : mv : - 2 : C/ D5 2 Current alarm on lower threshold : min value - File and printed copies of this document are not subject to document change control. Page 4/0

5 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls INPUT REGISTERS - Words (R) Bit Position Description Type Scale Unit Range Note Read Code D52 Current alarm on upper threshold cause: 0 : No Alarm / : I / 2 : I2 / : I / 4 : IN / 5 : U2 / 6 : U2 / 7 : U / 8 : P+ / 9 : Q+ / 0 : S / : F / 2 : PFL / 5: thdi / 6: thdi2 / 7 : thdi / 8 : thdu2 / 9 : thdu2 / 20 : thdu / 2 : Hour / 22: V / 2 : V2 / 24 : V / 26: thdv / 27 : thdv2 / 28 : thd V / : PFC / 2 : T C 0 : - / 2 / / 4 : ma 5 / 6 / 7 : mv 8 : mw 9 : mvar 0 : mva : Hz/000 2 : - 5 / 6 / 7 : /000 8 / 9 / 20 : /000 2 : Hour/00 22 / 2 / 24 : mv : - 2 : C/ D5 2 Current alarm on upper threshold : max value D54 Current alarm duration s C Measure - Metrology Affected by current and voltage transformers C550 2 Hour Meter unsigned long 0,0 h NOTE C552 2 Phase to Phase Voltage: U2 unsigned long 0,0 V NOTE C554 2 Phase to Phase Voltage: U2 unsigned long 0,0 V NOTE C556 2 Phase to Phase Voltage: U unsigned long 0,0 V NOTE C558 2 Simple voltage : V unsigned long 0,0 V NOTE C55A 2 Simple voltage : V2 unsigned long 0,0 V NOTE C55C 2 Simple voltage : V unsigned long 0,0 V NOTE C55E 2 Frequency : F unsigned long 0,0 Hz NOTE C560 2 Current : I unsigned long ma NOTE C562 2 Current : I2 unsigned long ma NOTE C564 2 Current : I unsigned long ma NOTE C566 2 Neutral Current : In unsigned long 0,0 ma NOTE C568 2 active Power +/- : P signed long 0,0 kw NOTE C56A 2 reactive Power +/- : Q signed long 0,0 kvar NOTE C56C 2 apparent power : S signed long 0,0 kva NOTE C56E 2 power factor : -: leading et + : lagging : PF signed long 0,00 NOTE C570 2 Active Power phase +/- : P signed long 0,0 kw NOTE C572 2 Active Power phase 2 +/- : P2 signed long 0,0 kw NOTE C574 2 Active Power phase +/- : P signed long 0,0 kw NOTE C576 2 Reactive Power phase +/- : Q signed long 0,0 kvar NOTE C578 2 Reactive Power phase 2 +/- : Q2 signed long 0,0 kvar NOTE C57A 2 Reactive Power phase +/- : Q signed long 0,0 kvar NOTE C57C 2 Apparent power phase : S unsigned long 0,0 kva NOTE C57E 2 Apparent power phase 2 : S2 unsigned long 0,0 kva NOTE C580 2 Apparent power phase : S unsigned long 0,0 kva NOTE C582 2 Power Factor phase -: leading and + : lagging : PF signed long 0,00 NOTE C584 2 Power Factor phase 2 -: leading and + : lagging : PF2 signed long 0,00 NOTE C586 2 Power Factor phase -: leading and + : lagging : PF signed long 0,00 NOTE C650 6 Measure - Energies C650 2 Hour meter unsigned long 0,0 h NOTE C65C 2 Partial Positive Active Energy: Ea+ unsigned long kwh NOTE C65E 2 Partial Positive Reactive Energy: Er + unsigned long kvarh NOTE File and printed copies of this document are not subject to document change control. Page 5/0

6 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls INPUT REGISTERS - Words (R) Bit Position Description Type Scale Unit Range Note Read Code C6A0 4 Measure - Energies per tariff C6A0 0 >= Tariff number <= 8 value if not available 0x C6A Tariff number in progress..8 value if not available 0x C6A2 6 8 * Positive Active Energies unsigned long kwh NOTE C6B2 6 8 * Positive Reactive Enegies unsigned long kvarh NOTE C750 8 Measure - Statistique Affected by current and voltage transformers C77E 2 Max/avg I unsigned long ma NOTE C780 2 Max/avg I2 unsigned long ma NOTE C782 2 Max/avg I unsigned long ma NOTE C784 2 Max/avg In unsigned long ma NOTE C786 2 Max/avg P+ unsigned long 0,0 kw NOTE C788 2 Max/avg P- unsigned long 0,0 kw NOTE C78A 2 Max/avg Q+ unsigned long 0,0 kvar NOTE C78C 2 Max/avg Q- unsigned long 0,0 kvar NOTE C78E 2 Max/avg S unsigned long 0,0 kva NOTE C850 0 Measure - Metrology No Affected by current and voltage transformers C850 Hour Meter unsigned word h NOTE C85 Phase to Phase Voltage: U2 unsigned word 0,0 V NOTE C852 Phase to Phase Voltage: U2 unsigned word 0,0 V NOTE C85 Phase to Phase Voltage: U unsigned word 0,0 V NOTE C854 Simple voltage : V unsigned word 0,0 V NOTE C855 Simple voltage : V2 unsigned word 0,0 V NOTE C856 Simple voltage : V unsigned word 0,0 V NOTE C857 Frequency : F unsigned word 0,0 Hz NOTE C858 Current : I unsigned word ma NOTE C859 Current : I2 unsigned word ma NOTE C85A Current : I unsigned word ma NOTE C85B Neutral Current : In unsigned word ma NOTE C85C active Power +/- : P signed word 0,0 kw NOTE C85D reactive Power +/- : Q signed word 0,0 kvar NOTE C85E apparent power : S unsigned word 0,0 kva NOTE C85F power factor : -: leading and + : lagging : PF signed word 0,00 NOTE C860 Active Power phase +/- : P signed word 0,0 kw NOTE C86 Active Power phase 2 +/- : P2 signed word 0,0 kw NOTE C862 Active Power phase +/- : P signed word 0,0 kw NOTE C86 Reactive Power phase +/- : Q signed word 0,0 kvar NOTE C864 Reactive Power phase 2 +/- : Q2 signed word 0,0 kvar NOTE C865 Reactive Power phase +/- : Q signed word 0,0 kvar NOTE C866 Apparent power phase : S unsigned word 0,0 kva NOTE C867 Apparent power phase 2 : S2 unsigned word 0,0 kva NOTE C868 Apparent power phase : S unsigned word 0,0 kva NOTE C869 Power Factor phase -: leading and + : lagging : PF signed word 0,00 NOTE C86A Power Factor phase 2 -: leading and + : lagging : PF2 signed word 0,00 NOTE C86B Power Factor phase -: leading and + : lagging : PF signed word 0,00 NOTE C86F Total Positive Active Energy (no resetable) : Ea+ unsigned word MWh NOTE File and printed copies of this document are not subject to document change control. Page 6/0

7 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls INPUT REGISTERS - Words (R) Bit Position Description Type Scale Unit Range Note Read Code 54 5 C87 Total Negative Active Energy (no resetable) : Ea- unsigned word MWh NOTE C900 2 Measure - Temperatures 0=no, C900 Internal module Temperature present 0, =yes C90 module Temperature unsigned word C C950 0 Measure - Harmonic THD C950 thd U2 unsigned word 0, % NOTE C95 thd U2 unsigned word 0, % NOTE C952 thd U unsigned word 0, % NOTE C95 thd V unsigned word 0, % NOTE C954 thd V2 unsigned word 0, % NOTE C955 thd V unsigned word 0, % NOTE C956 thd I unsigned word 0, % NOTE C957 thd I2 unsigned word 0, % NOTE C958 thd I unsigned word 0, % NOTE C959 thd In unsigned word 0, % NOTE NOTE value if not available (0xFFFFFFFF for long, 0xFFFF for word) NOTE 2 value if not available (0x7FFFFFFF for long, 0x7FFF for word) EXAMPLE: Read the "Simple voltage: V" value from device having Modbus address 5 Modbus Request: 05 0 C CRC Bit Position Description Type Scale Unit Range Note Read Code C558 2 Simple voltage : V unsigned long 0,0 V NOTE Modbus Reponse: "Simple voltage" value: ) 2) ) 4) 5) FC CRC Value 08FC is in Hexadecimal Value 08FC correspond to 200 in Decimal "Simple voltage: V" register has Scale=0,0 Real value= Value * Scale "Simple voltage: V" value is 200*0,0=20 V File and printed copies of this document are not subject to document change control. Page 7/0

8 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls HOLDING REGISTERS - Words (R&W) Reset Bit Position Description Scale Unit Range Note Read Reset : Max 4I : 0x Max P+,Q+,S : 0x2 kwh+ : 0x80 kvarh+ : 0x00 All parameters : 0x000 These values could be combine all E00 7 Table setup Network : 0 : BL : 2BL E00 2 : BL : NBL 4 : 4BL 5 : 4NBL E0 Current Transformer secondary : : A 5: 5 A A E02 Current Transformer primary A E0 Reserved Synchronisation of I AVG/MAX: E04 2 : 2 seconds 0 : 0 seconds 00 : 5 minutes 480 : 8 minutes 600 : 0 Minutes E : 5 minutes 200 : 20 minutes 800 : 0 minutes 600 : 60 minutes Synchronisation of P/Q/S AVG/MAX 0 : 0 seconds 00 : 5 minutes 480 : 8 minutes 600 : 0 Minutes E : 5 minutes 200 : 20 minutes 800 : 0 minutes 600 : 60 minutes OUT : pulse output allocation : 0 : kwh+ : kvarh E07 2 :Alarm : Command OUT : pulse output value : 0 : 0, kwh/kvarh : kwh/kvarh 2 : 0 kwh/kvarh E08 : 00 kwh/kvarh 4 : 000 kwh/kvarh 5 : 0000 kwh/kvarh OUT : pulse output duration : : 00ms - 2 : 200ms : 00ms - 4 : 400ms 5 : 500ms - 6 : 600ms 7 : 700ms - 8 : 800ms 9 : 900ms E09 Hour meter allocation : Auxiliary power supply 2 : Currents : phase to phase voltage Write 6 File and printed copies of this document are not subject to document change control. Page 8/0

9 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls HOLDING REGISTERS - Words (R&W) Bit Position Description Scale Unit Range Note Read E0A Hour meter trigger threshold A/V E0B Alarm Type : : I 2 : In : U 4 : V 5 : P+ 6 : Q+ 7 : S+ 8 : PFC 9 : PFL 5 : P 6 : Q 7 : S 8 : CPF 9 : LPF 0 : THDU : THDV 2 : THDI : HOUR 4 : F E0C Alarm Specified time (0-999) E0D Alarm upper Threshold E0E Alarm Lower Threshold E0F Alarm Hysteresis(0-99) E0 Relay State : 0 : Open : Closed E000 Network Settings E000 Network Type : 0 : BL : 2BL 2 : BL : NBL 4 : 4BL 5 : 4NBL E00 Current Transformer secondary : : A 5: 5 A A E002 Current Transformer primary A E200 Action System E200 Action : 0xA : Product Configuration storage 0xB2 : Produit reboot value if not available = 0xFFFF value if not available = 0xFFFF value if not available = 0xFFFF Write NOTE4 6 NOTE 4 - Configuration Procedure ) Write the new Configuration (one or more registers...) File and printed copies of this document are not subject to document change control. Page 9/0

10 PM Multifunction meter Cat No. FN200 - ModbusTable BT EN v.0.xls HOLDING REGISTERS - Words (R&W) Bit Position Description Scale Unit Range Note Read Write 2) Save/Confirm the new Configuration (writing the value 0xA in the register 0xE200) ) Reset the device (writing the 0xB2 in the register 0xE200). The new Configuration is now available 4) The new Configuration is now available File and printed copies of this document are not subject to document change control. Page 0/0