WINSTON WORKSTATION INSTALLATION INSTRUCTIONS. STEP 1 COLUMN...Page 2

Transcription

1 WINSTON WORKSTATION INSTALLATION INSTRUCTIONS STEP COLUMN...Page 2 STEP 2 MOUNTS Free Standing Base...Page 3 Clamp Mount...Page 4 Thru Mount...Page 5 6 STEP 3 WORK SURFACE...Page 6 8 STEP 4 CENTER BEAM...Page 7 4 STEP 5 EXTENSION BEAMS (optional)...page 8 STEP 6 MONITOR TILTER...Page 9 STEP 7 MONITOR CUPS...Page 0 STEP 8 CABLE MANAGEMENT...Page 3 7 NOTE: Depending on your Winston Workstation configuration, you may not receive all the parts shown within this instruction booklet. 2 Installation may require two people. PAGE OF Innovative Office Products, LLC P5599 REV D

2 STEP COLUMN IMPORTANT: Do not pull excessively on cable doing so may result in accidental actuation of column. B A 2 3 i Confirm cable is properly seated into position. U Use 7/32" Allen wrench to press cable firmly into place. PAGE 2 OF 3

3 STEP 2 FREE STANDING BASE MOUNTS 2 3 Hang base plate over edge of work surface to allow access to countersunk holes. Side of base plate with felt pads should be face down. Place work surface on base plate to aid as a counterbalance. C D 4 Note the orientation of column cable exit and base plate cable should exit in direction as shown. E 7/32" PAGE 3 OF 3

4 STEP 2 CLAMP MOUNT MOUNTS 2 3 G H Note the orientation of column cable exit and mount cable should exit in direction as shown. F E B A I 7/32" J PAGE 4 OF 3

5 STEP 2 THRU MOUNT MOUNTS 2 Note the orientation of column cable exit and mount cable should exit in direction as shown. K E 7/32" * L B A M N PAGE 5 OF 3 * The supplied mounting hardware may need to change depending upon mounting substrate.

6 STEP 3 WORK SURFACE 2 Slide utility tray onto work surface. Utility tray simply rests on top of work surface. Two people may be required to install work surface to column. One to hold the work surface and the second person to secure the column clamp. P Q O A i 3 IMPORTANT: Tighten bolts evenly. Work surface clamp should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. 4 2 PAGE 6 OF 3

7 STEP 4 CENTER BEAM 2 3 R S P i IMPORTANT: Tighten bolts evenly. The beam should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level T W U V PAGE 7 OF 3

8 STEP 5 (optional) EXTENSION BEAMS 2 X Y Y Z Z 3 V T U i PAGE 8 OF 3

9 STEP 6 MONITOR TILTER STANDARD TILTER & SPRING TILTER QUICK RELEASE TILTER 2 2 CC or DD BB AA EE EE FF GG FINE TUNE HEIGHT ADJUST TILTER BB CC or DD EE AA AA HH AA PAGE 9 OF 3

10 STEP 7 2 MONITOR CUPS i II 7/32" II JJ KK PAGE 0 OF 3

11 STEP 8 CABLE MANAGEMENT LL MM PAGE OF 3

12 HEIGHT ADJUSTMENT Press button and hold. Lift up/down. Release to lock in place. i Is your height adjust button not working? If so, make the adjustments below Slide workstation so that the work surface hangs over desk edge to allow access to underneath the work surface. Loosen the two screws as shown. Slide bracket in the direction shown and tighten screws. Test height adjust button readjust by repeating the steps above as necessary. PAGE 2 OF 3

13 WINSTON WORKSTATION A Work Surface I 4469 B Column Felt Pad J Free Standing Base K L 3/8-6 x " FHSCS F Large L M N /4-20 x /2" PhPHS O Small L P 32 Thru Mount Base Plate S Center Beam (30") T Thru Mount Washer U Thru Mount Nut 0-32 x " FHSCS AA Allen Wrench BB End Cap CC Column Cap DD X Hinge 449 PAGE 3 OF 3 II 75/00 mm VESA Adapter Standard Monitor Tilter HD Monitor Tilter EE M4 x 2mm PhPHS FF Monitor Cup 435 JJ Dog Washer KK 0-32 x /2" FHSCS 7240 LL x 3/8" PhPHS Fine Tune Adjust W HH V Extension Beam (0" or 20") QR Monitor Tilter /32" Allen Wrench GG or FHSCS 0-32 x -/2" 7467 Column Clamp Z 70 /4-20 x 2-/2" Hex Head Bolt 0-32 x 9/6" FHSCS H R G /2-3 x 3 Set Screw Y E Utility Tray D Q M C Spacer PARTS LIST* Column Cable Clip MM Extension Beam Cable Clip 252 QR VESA Adapter * Depending on your Winston Workstation configuration, you may not receive all parts shown above.