PR-6000 Spot. PR LIGHTING LTD. 1/26

Transcription

1 PR-6000 Spot The user manual contains important information about the safe installation and use of a projector. Please read and follow these instructions carefully and keep the manual in a safe place for future reference. PR LIGHTING LTD. 1/26

2 INDEX 1. SAFETY AND WARNINGS 2. INSTUCTIONS CLEANING AND MAINTENANCE LUBRICATION TROUBLESHOOTING 3. APPEARANCE 4. INSTALLATION RIGGING POWER CONNECTIONS DMX CONTROL CONNECTIONs DMX TERMINATOR ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP GOBO/COLOR FILTER REPLACEMENT 5. SETUP AND CONFIGURATION FRONT PANEL OPERATION DMX START ADDRESS DMX WIRELSESS CONTROL STAND-ALONE MODE MASTER/SLAVE MODE 6.OPERATION MENU 7. DMX PROTOCOL 8. LED INDICATION 9. ERROR MESSAGE 10.TECHNICAL DATA 11.CIRCUIT DIAGRAM AND PCB CONNECTIONS CIRCUIT DIAGRAM 12.COMPONENT ORDER CODES ACCESSORIES The following items are supplied with the projector and please check: Name Quantity Unit Remark G clamp 2 Pcs XLR Connector 1 Set With Male and female sockets Safety cord 2 Pc Spare Gobo 4 pc User manual 1 Pc Ω clamp 2 Pcs Optional Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them. Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer. 2/26

3 1. SAFETY AND WARNINGS NOTE Before a projector s installation, power-on, operation and maintenance, please carefully read the safety information hereinafter! The following safety signs are used in the user manual. Warning User Manual Electrical shock Goggles Protective Gloves Flames High Temperature When unpacking, check if there is transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use it. The manufacture is not responsible for loss caused by the user not following the manual or changing the projector as he/she likes Please be noted that the damage caused by changing the projector at will is not warranted. Do not hesitate to contact the dealer or the manufacturer if any questions or advice. The projector is for indoor use only, IP20. Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids. The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while being operated The projector is only intended for installation, operation and maintenance by qualified personnel. And the operation must strictly follow the procedures in the manual No repairable parts in the projector and do not open covers for maintenance by yourself. Don t look straightly into the light sources especially for epileptics, otherwise eyes will be burned. Do not connect this device to any type of dimmer pack After lamp switched on, the minimum distance between the projector and illuminated surface is 10m lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the light output will be compromised. Before operation, please confirm that all covers(housing) are on and screws tightened. It s forbidden to use a projector while covers(housing)are off Keep the lamp clean and do not touch it with bare hands. While operating it, wear protective items. Any electrical connection must be carried out by a qualified person. Before installation, please confirm the voltage supplied matches what is required for the projector Each projector must be properly earthed and installed as per related electrical standards. Do not use power cord with its insulator damaged and connect the power cord with other cables. If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or by pulling the power cable. All power cords must conform to related safety and regulations While being operated, the projector should not be under rains or in humidity. Do not switch on and off the projector constantly in very short intervals, otherwise the light source s and other electrical parts life will be shortened. 3/26

4 There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord supplied through the safety cord holes for safety support. Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power mains. After running for 30minutes, the temperature of the housing of the projector is 45.After stable operation, its temperature is 60. While the lamp is stricken for the first time, there will be smoke and strange smell. It s normal and does not mean the projector has some defects. Do not mount the projector directly on inflammable surface. Do not project the beam straightly on combustible items and the minimum distance between the projector and illuminated items is 10m. A projector should be installed with good ventilation and the minimum distance between the projector and walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable. 2. INSTRUCTIONS CLEANING AND MAINTENANCE If a projector can t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved, restart the projector. The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned periodically to optimize light output. Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning work. It s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean and do not touch optical parts with bare hands. Before any maintenance and cleaning, please ensure the project is off the power Only qualified person is allowed to do maintenance During maintenance and before maintenance, the projector must be off power. To avoid internal damage, sun light or other light mustn t penetrate into the projector via front lens whether it runs or not Do not use alcohol or other organic solvent to clean the housing to avoid damage. Do not use any solvent with chemical elements to clean color filters or hot mirror. LUBRICATION To ensure smooth movement of gobos and zoom and focus lens, it s advised rotators bearings and 2 sliding bars for zoom and focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised.. 4/26

5 TROUBLESHOOTING PROBLEM ACTION Check the fuse on the power socket. The projector doesn t switch on Check the lamp. The lamp is on but the projector doesn t respond Make sure that the fixture s start address is right to the controller Replace or repair the XLR signal cable. The projector functions intermittently Make sure the fan is working well or fans and their shields are not blocked Make sure the lamp is within its lifespan Beam appears dim, Low in brightness Remove dust or grease from the lenses. The project image appears to have a halo Carefully clean the lamp, optical lenses and other components. Check if lens are in good condition(not cracked) Heavily Defective Beam Clean dust or grease on the lens. 3. APPEARANCE 4. INSTALLATION RIGGING Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It s forbidden to run a projector with power while it is locked SAFETY CORD CLAMP HANDLE WARNING To pass 2 SAFETY CORDS through 4 HOLES for safety! 257 CONTROL PANEL 106 5/26

6 Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector to is secure and strong enough to support the weight of the unit. WARNING: The projector MUST be lifted or carried by the HANDLES instead of clamps..for safety the safety cord should afford 10 times the Projector s weight. POWER CONNECTION Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each projector be connected with power separately so that they may be individually switched on and off. Note: If projectors are connected in series, please connect POWERIN port of the 1 st projector with the Power Mains, then connect its POWER OUT with POWER IN of the 2 nd projector, and so on till all fixtures are connected. If the voltage supplied is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores of the wires for the Power in/out cables must be equal or bigger than 2.5mm 2. DMX CONTROL CONNECTION: The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in accordance with the standards concerned. If any questions about the electrical installation, do not continue but consult a qualified electrician. Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above. Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets mustn t be connected in any way other than mentioned in the above figure. The XR330BWS accepts digital control signals in protocol DMX512 (1990). Connect the controller s DMX output to the first fixture s DMX input, and connect the first fixture s DMX output to the second fixture s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture s DMX output to a DMX terminator as shown in the figure below. 6/26

7 DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT TO CONTROLLER TO TERMINATER DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain. PIN 2 PIN 3 ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP Before installation/replacement/alignment of a lamp, disconnect the unit from the power and let it cool first. Lock Tilt in the figure below and open the lamp cover after its 4 screws are loosened. After removal of the lamp cover, take out the lamp while the 2 screws at both ends of the lamp are loosened. Insert a new lamp. Note: while placing a new lamp, do not touch the burner of the lamp with bare hands, otherwise the light output will be compromised. Fasten the 4 fast-fit screws after the lamp cover is on Important: The unit uses high voltage discharge lamp with external igniter( INSTRUCTIONS packed with the lamp. ). While using the lamp, please carefully read Don t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to impair the beam output. While lamp s installation, do not damage the metal wire around the burner. Please read "Instructions " enclosed with the lamp Do operate the projector while adjusting the lamp 7/26

8 GOBO REPLACEMENT Lock the tilt and loosen the 6 fast-fit screws on the upper cover,after removing the cover, you will see the structures as the figure below. Before replacing a gobo on the fixed gobo wheel, use your finger to remove the spring tightening it and take the old one out with due care. At last put the new into the wheel. To replace a gobo on the rotating gobo wheel: take the rotator from the wheel, take the gobo out from the rotator by removing the tightening spring. Put the new gobo back to the rotator, then tighten it with the spring. Please ensure the spring is in the narrow location of the rotator, which is the internal ring of it and flatten it. At last, pull up the spring strip using proper tool and put the rotator back to the wheel with the assistance by another hand. Note: Do not touch the glass gobo with bare hand. Place clean and soft paper or cloth between hand and glass gobos. Tighten 6 fast-fit screws after the cover is on. Unlock the tilt. DANGER! Before replacement of gobos, the projector must be off the power. 5. SETUP AND CONFIGURATION Front Panel Operation W-DMX Projector configuration can be set conveniently via push button and LCD display. Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the OPERATION MENU section. Rotate the knob clockwise UP or anti- clockwise DOWN if you want to browse through the various Setup Options. Press button ENTER to save your settings or enter the submenu. Press button UP or DOWN to change values(plus or minus) 8/26

9 Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically. Shortcut key: Press UP and DOWN buttons together to invert the screen; Press DOWN and ENTER together to change between English and Chinese menus. DMX START ADDRESS Each unit must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller. The unit has 3 DMX modes. There are standard mode,short mode and extended mode. For example standard mode has 31 channels, so set the No. 1 projector s address 001, No. 2 projector s address 032, No. 3 projector s address 063, No. 4 projector s address074, and so on. Launch the projector. Press button ENTER more than 5seconds to unlock panel. Press button ENTER to display DMX address; Press button UP and DOWN, you can set the address; Press button ENTER to confirm; after powered on next time, the default will be last value saved Press button FUNC, it will return to the upper menu. DMX WIRELESS CONTROL (If the projector has the function) The projector has wireless control function with wireless receiver module and antenna for remote control. The setup of it is below: 1. Enter into the projector s menu. Select the menu Config Settigns via the bottoms of UP and DOWN 2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the front panel will be on, meaning wireless control function is activated. Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press Enter for the menu of Unlink Wireless under the upper level menu of Config Settigns. STAND-ALONE MODE Operate the projector without connecting with a controller, enable the master mode through the operation panel, the projector will run in Stand-Alone mode automatically. DMX address can be set at any number within 512. MASTER/SLAVE MODE Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First, connect the first fixture s DMX output to the second fixture s DMX input using XLR-XLR control cable and then connect the second fixture s DMX output to the third fixture s DMX input, and so on until all projector are connected in this way. Eventually connect the last fixture s DMX output to a DMX terminator. Set 1 st projector as the master and others are Slaves. Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master and Slaves operation mode can be set accordingly. After Powered on, the group will run in Master/Slave Mode DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT TO CONTROLLER TO TERMINATER 9/26

10 6. OPERATION MENU First Menu Secondary Menu Third Menu Fourth Menu PR Lighting PR-6000 Spot DMX Address=X DMX Address Reset Config Settings X Reset Are You Sure DMX Mode (Default: Standard 16 ) Lamp Control (Default: By Control Channel) Standard 16 Extended 16 Short 8 Lamp Control By Control Channel Lamp Control By Power On Lamp Control By DMX Present Option Settings Loss of DMX (Default: Normal time out) Factory Settings (Press button DOWN/UP/ENTER at the same time to enter the sub-menu) Color Positions (Default: Step) F-Gobo Positions (Default: Step) Pan DMX Invert (Default: Off) Tilt DMX Invert (Default: Off) Pan Tilt Swap (Default: Off) Dimmer Invert (Default: Off) Iris Invert (Default: Off) Zoom Invert (Default: Off) When DMX is Lost Normal time out When DMX is Lost Hold Last Value Fixture type (WARNING:Never change the fixture type or the system will be damaged!) 10/26 Color Positions STEPPED Color Positions LINEAR F-Gobo Positions STEPPED F-Gobo Positions LINEAR Pan DMX Invert OFF Pan DMX Invert ON Tilt DMX Invert OFF Tilt DMX Invert ON Pan Tilt Swap OFF Pan Tilt Swap ON Dimmer Invert OFF Dimmer Invert ON Iris Invert OFF Iris Invert ON Zoom Invert OFF Zoom Invert ON

11 CMY Invert (Default: Off) CTO Invert (Default: Off) Defaults (Default: Off) Display Mode Display Invert CMY Invert OFF CMY Invert ON CTO Invert ON CTO Invert OFF Defaults OFF Defaults Restore Defaults Display On Always Display After Delay Display Invert Off Display Invert On Min Display Options Display Dimming A B C D E F Full Display Contrast Display Language (1-21) Language= English Language= Chinese Lamp Hours ) Information Total Hours Temperature Display Board Display Board= 11/26 X

12 Software Version View DMX Values Electronic SN RDM Device Label Pan Encoder Tilt Encoder Driver Board 1 Driver Board1 = Driver Board 2 Driver Board 3 Driver Board 4 Pan and Tilt Board X Driver Board2= X Driver Board3= X Driver Board4= X Pan and Tilt Board= X Head Sensor Head Sensor = Display Board Driver Board 1 Driver Board 2 Driver Board 3 Driver Board 4 Pan and Tilt Board DMX Channel 1=X Electronic SN= ************ RDM Device Label ANSI E1.20 RDM Version 1.0 Pan Encoder Wiring Normal Pan Err 0 Count 0 Tilt Encoder Wiring Normal Pan Err 0 Count 0 X Display Board System=X Boot=X Driver Board 1 System=X Boot=X Driver Board 2 System=X Boot=X Driver Board 3 System=X Boot=X Driver Board 4 System=X Boot=X Pan Tilt Board System=X Boot=X Driver Faults X Over Temp 0 Y Over Temp 0 X Fault 0 Y Fault 0 12/26

13 Test Mode Factory Setup Self Test Lamp Status Factory Setup OFF Factory Setup ON Self Test OFF Self Test ON S=X C=X Lamp On/Off Lamp Manual Control Turn Lamp On Turn Lamp Off Wireless Options (Only for the projectors requested for Wireless Control) Operation Mode Wireless Mode Un-Link Wireless DMX Operation Master Mode Slave Mode Static Scene Wireless Mode XLR First Wireless Mode Wireless Only Wireless Mode XLR Only Wireless Mode Wireless to XLR Wireless Mode Wireless Only Really Un-Link Enter=Yes Select Memory User Memory1-2 Select Memory User Memory1-2 Shutter Dimmer Dimmer Low CMY Macro Cyan Yellow Magenta User Memories Edit User Memory User Memory1-2 Scene CTO Color Wheel Iris Iris Macro Fixed Gobo R Gobo Wheel R Gobo Rotate R Gobo Rotate L R Gobo 2 Wheel R Gobo 2 Rotate R Prism In Out R Prism Rotate Effects In Out Effects Rotate Frost 13/26

14 Focus Zoom Pan Coarse Pan Fine Tilt Coarse Tilt Fine M-Speed Delay Link to Step S Shutter Dimmer Dimmer Low CMY Macro Cyan Yellow Magenta Static Scene CTO Color Wheel Iris Iris Macro Fixed Gobo R Gobo Wheel R Gobo Rotate R Gobo Rotate L R Gobo 2 Wheel R Gobo 2 Rotate R Prism In Out R Prism Rotate Effects In Out Effects Rotate Frost Focus Init User Memory 14/26 Reset User1 Zoom Pan Coarse Pan Fine Tilt Coarse Tilt Fine M-Spee d Delay Link to Step Reset User1 Unlock S

15 Reset User2 Reset Static Scene Reset User2 Unlock Reset Static Scene Unlock Note: 1. The parameters transmitted from the mater if multiple units are synchronized include: DMX channel mode,display setting, operation mode including user memory 2. The unit which receives the parameters sent is automatically set as the Slave 7. DMX PROTOCOL Short Mode Standard Mode Extended mode Function DMX Description Strobe Dimmer Close Open Strobe from slow to fast Strobe Macro Open Close Linear Dimming (0-100%) 3 3 Dimmer Fine Dimming in 16 Bit White Yellow+Magenta=Red Yellow Yellow +Cyan=Green CYM Macro Cyan Cyan+Magenta=Purple Magenta CYM color mixing from slow to fast CYM-Cyan Cyan Linear adjustment(0%-100%) 6 CYM-Cyan Fine Cyan in 16 Bit CYM-Yellow Yellow Linear adjustment (0%-100%) 8 CYM-Yellow Fine Yellow in 16 Bit CYM-Magenta Magenta Linear adjustment (0%-100%) 10 CYM-Magenta Fine Magenta in 16 Bit CTO CT Linear adjustment from low to high 12 CTO Fine CT in 16 Bit White White/Color Color 1 Colour Wheel Color1/Color Color Color2/Color3 15/26

16 Color Color3/Color Color Color4/Color Color Color5/Color Color Color6/Color Color Color7/white White Forward Rainbow effect from slow to fast Reverse Rainbow effect from slow to fast Iris Linear adjustment (0%-100%) Fixed Gobo Wheel Rotating Gobo Wheel 1 Iris Fine Iris in 16 bit No Macro 1: from big to small with speed from slow to fast Macro 2:from small to big with speed from slow to fast Iris Macro Macro 3: Iris from Open to Close from slow to fast Iris Effect Iris Effect Iris Effect Iris fully open White Gobo Gobo Gobo Gobo Gobo Gobo Gobo Forward Rotation from slow to fast Reverse Rotation from slow to fast Gobo1 shakes from slow to fast Gobo2 shakes from slow to fast Gobo3shakes from slow to fast Gobo4shakes from slow to fast Gobo5 shakes from slow to fast Gobo6shakes from slow to fast Gobo7shakes from slow to fast White Gobo Gobo Gobo Gobo Gobo Gobo6 16/26

17 Gobo rotation Forward Rotation from slow to fast Reverse Rotation from slow to fast Gobo1 shakes from slow to fast Gobo2 shakes from slow to fast Gobo3shakes from slow to fast Gobo4shakes from slow to fast Gobo5 shakes from slow to fast Gobo6shakes from slow to fast Gobo Indexing(0 ~540 ) 128 Stop Forward Rotation from slow to fast Stop Reverse Rotation from slow to fast Gobo rotation 1 Fine Rotating Gobo Wheel Gobo rotation Gobo Rotation1 in 16 bit White Gobo Gobo Gobo Gobo Gobo Gobo Forward Rotation from slow to fast Reverse Rotation from slow to fast Gobo1 shakes from slow to fast Gobo2 shakes from slow to fast Gobo3shakes from slow to fast Gobo4shakes from slow to fast Gobo5 shakes from slow to fast Gobo6shakes from slow to fast Gobo Indexing(0 ~540 ) 128 Stop Forward Rotation from slow to fast Stop Reverse Rotation from slow to fast Gobo rotation 2 Fine Prism Prism rotation Effect Wheel Effect Wheel Rotation 17/ Gobo Rotation2 in 16 bit Open facet Prism In Prism Indexing 128 Stop Forward Rotation from slow to fast 192 Stop Reverse Rotation from slow to fast No Slow Rotation Forward Rotation from slow to fast Reverse Rotation from slow to fast Frost Frost Linearly In Linear Focusing

18 Focus Focus Fine Zoom Zoom Fine Pan Pan Fine Tilt Tilt Fine Focusing in 16 bit Linear Zooming Zooming in 16 bit Pan Rotation Tilt in 16 Bit Tilt Rotation Tilt in 16 Bit Pan & Tilt speed Control Pan & Tilt Speeds from fast to slow Reserved Reset Reserved Lamp off(10s) Reserved Decrease Ballast Power Reserved Lamp on Remark: If you intend to turn on/off the lamp via the last channel of the controller, don t attempt to push the channel to value immediately after turning it off, or push the slide bar to value to wait it cooling. Under these 2 circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it on. 8. LED INDICATION Green Blue (Only for the projectors requested for Wireless Control) On Off Flash On Off Flash DMX signal OK No DMX signal DMX signal error Wireless signal OK Not connection to any transmitter Lost contact with the transmitter or linking transmitter 9. ERROR MESSAGE The Fixture can detect any errors during the reset and may show errors below: 18/26

19 Sensor Err S1-M1 Color Wheel Error(Driver Board1 motor1 ) Sensor Err S1-M2 CTO error (Driver Board1 motor2) Sensor Err S1-M3 Cyan Error(Driver Board1 motor3) Sensor Err S1-M4 Yellow Error(Driver Board1 motor4) Sensor Err S1-M5 Magenta Error(Driver Board1 motor5) Sensor Err S2-M2 Fixed Gobo Wheel Error(Driver Board2 motor2) Sensor Err S2-M3 Rotating Gobo Wheel1 Error(Driver Board2 motor3) Sensor Err S2-M4 Gobo1 Rotation(Driver Board2motor4) Sensor Err S3-M1 Rotating Gobo Wheel2Error(Driver Board3 motor1) Sensor Err S3-M2 Gobo2 Rotation(Driver Board3 motor2) Sensor Err S3-M3 Effect Wheel In/Out Error(Driver Board3 motor3) Sensor Err S3-M4 Effect Wheel Rotation Error(Driver Board3 motor4) Sensor Err S3-M5 Focus Error(Driver Board3 motor5) Sensor Err S3-M6 Zoom Error(Driver Board3 motor6) Sensor Err S4-M1 Prism Error(Driver Board4 motor1) Sensor Err S4-M2 Prism Rotation Error(Driver Board4 motor2) Sensor Err S4-M3 Frost Error(Driver Board4 motor3) 10. TECHNICAL DATA INPUT VOLTAGES 200V/220V/230V/240V AC,50/60Hz POWER COSUMPTION 2300W@220V 19/26

20 LAMP PHILIPS Color Temperature Ceramic Stand Manufacturers Rated Lamp Life MSR GOLD TM 2000/1 FastFit 5800K Single ended 750hours COLORS A CMY linear mixing system with macros UV 1 color wheel: 7colors+ open, half color effect Rainbow effect with bi-directional and variable speeds Stepping/linear color changing A Orange A Red A Yellow A Pink A Blue A Red 620±5NM A Blue 540±5NM A Yellow 500±5NM A Pink 510/545±5NM A Green 490/585±5NM A Orange 600±5NM A UV 460/690±5NM A Green GOBOS 2 rotating gobo wheel: 6 replaceable gobos+ open, glass or metal gobo Bi-directional rotation with variable speeds With indexing function Gobo shake effect with variable speeds Bi-directional Scrolling with Variable Speeds Rotating Gobo Wheel 1 20/26

21 Rotating gobo Wheel2 1 fixed gob wheel: 7 replaceable gobos+ open Gobo shake effect with variable speeds, bi-directional scrolling with variable speeds Gobo outer size: 36.3mm Gobo image size: 26mm PRISM 1pc of 3-facet prism, Bi-directional rotation with variable speeds and indexing function FROST 1pc frost filter, linear frost effect IRIS 5-100% linear adjustment with macros EFFECT WHEEL 1pc, replaceable, bi-directional rotation with variable speeds FOCUS DMX linear Focusing ZOOM DMX linear zooming DIMMER 0-100% Linear adjustment STROBE Double shutter blades, 0.3~25 F.P.S HEAD MOVEMENT Pan 540º, Tilt 270º with auto position correction 21/26

22 BEAM ANGLE linear zoom 7.3 ~ 68 with 16 bit function CONTROL DMX512, 3 pins and 5 pins interfaces RMD control protocol 25channels in short mode, 31channels in standard mode and 38channels in extended mode Self-test mode OTHER FUNCTIONS Adjustable Pan & Tilt speed Lamp and Total hours displayed LCD English and Chinese Display with Contrast and brightness adjustable Energy saving ballast Built-in sensor diagnostic system Built-in Chargeable battery and menu setting without power mains Input signal isolation Modular Structure for easy maintenance Ethernet Interface DMX512 wirless reciever Optional DMX512 Transmitter HOUSING High temperature ABS, IP20 NET WEIGHT 45Kg AMBIENT TEMPERATURE -20 C~40 C SIZES /26

23 LIGHT OUTPUT 63 (lux) 7.5 ( lux) DISTANCE( m) 7.5 DIAMETER( m) 63 DIAMETER( m) 0m 5m 10m 15m 20m 25m 30m CIRCUIT DIAGRAM AND PCB CONNECTIONS 23/26

24 12. COMPONENT ORDER CODES 24/26

25 NAME CODE NUMBER QTY REMARKS POWER SWITCH S POWER FILTER A 115/250VAC THERMAL SWITCH V-16A ELECTRONIC BALLAST W IGNITER W LAMP MSR GOLD TM 2000/1 FASTFIT TILT BELT M-5 PAN BELT M-9 CHAMBER FAN LAMP FAN FRONT CHAMBER FAN BASE FAN BALLAST FAN FOCUS MOTOR ZOOM MOTOR 2 ROTATING GOBO MOTOR 2# IRIS MOTOR PAN MOTOR TILT MOTOR 1 STROBE MOTOR 1 COLOR WHEEL MOTOR PRISM ROTATION MOTOR 1 ROTATING GOBO WHEEL 1# EFFECT WHEEL IN MOTOR 1 FROST FILTER MOTOR CYM MOTOR CTO MOTOR DIMMER MOTOR FIXED GOBO WHEEL MOTOR EFFECT WHEEL ROTATION MOTOR PAN AND TILT DRIVE BOARD DRIVER BOARD DRIVER BOARD DRIVER BOARD DRIVER BOARD MASTER BOARD POWER BOARD /26

26 PR LIGHTING LTD Xingye Avenue, Nancun Panyu Guangzhou, China TEL: PR lighting will try its best to offer accurate and overall information about a product s technical data. Any changes won t be notified if necessary. Patented Products. Counterfeiting Will be Prosecuted! P/N: Version: (Preliminary) 26/26