2012 Catalogue v.3. Centrifuges and laboratory products. Distributed By: PLP PACIFIC LABORATORY PRODUCTS

Transcription

1 2012 Catalogue v.3 Centrifuges and laboratory products Distributed By: PLP PACIFIC LABORATORY PRODUCTS

2 Distributed By: PLP PACIFIC LABORATORY PRODUCTS Pacific Laboratory Products PO BOX 465, Blackburn, VIC 3130 Free Call: Ph: (03) Fax: sales@pacificlab.com.au Catalogue Subject to technical change without notice. This catalogue have been sponsorized by Chamber of Commerce of Madrid. Álvarez Redondo S.A. C/ Misericordia, 20, 21 y AJALVIR Madrid (Spain) Scan the code using your mobile device for quick access to our website /PacificLab /PacificLabP

3 INDEX STANDARS ORTO ALRESA CENTRIFUGES Centrifugues guide Selection of the right equipment References tubes Microcen Serie Biocen Serie Unicen Serie Digicen Serie Consul Serie Digtor Serie Magnus SPECIAL APLICATIONS Centrifuge for petrol and derivates (Digtor 21C)... centrifugation on thin layer (Citocentrifuge)... Determination of fat in dairy products (Lacter)... Tissue Regeneration (PRGF Cen /Digtor Col)... AUTOCLAVES Y DESTILADORES Ecoclave Plus S & Ecoclave Plus B... Distillers BALL MILL Ball Mill... SIEVES SHAKER Sieves Shaker and Sieves... SHAKERS Bar Spin BATHS & INMERSION THERMOSTATS Therba and Therba D... Inmer E & Inmer P

4 DIRECTIVES & STANDARDS Orto Alresa in their commitment to the quality of its manufactured meets the following standards, directives and regulations: COMPANY: Standards ISO 9001:2008 ISO 13485:2003 Quality management systems Medical devices -- Quality management systems Standards & Orto Alresa PRODUCTS: Directives 2002/95/EC 2002/96/EC, 2003/108/EC 2004/108/EC 2006/95/EC 98/79/EC Regulation (EC) No 1005/2009 & 842/2006 Standards EN :2001 EN :2006 EN :2003 EN :2003 EN :2006 PACKAGING: International Standards For Phytosanitary Measures: ISPM 15 ROSH: on the restriction of the use of certain hazardous substances in electrical and electronic equipment WEE: on waste electrical and electronic equipment Electromagnetical Compatibility Relating to electrical equipment designed for use within certain voltage limits In Vitro diagnostic medical devices On substances that deplete the ozone layer on certain fluorinated greenhouse gases. Safety requirements for electrical equipment for measurement, control and laboratory use. General requirements Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-010: Particular requirements for laboratory equipment for the heating of materials Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-051: Particular requirements for laboratory equipment for mixing and stirring Electrical equipment for measurement, control and laboratory use. EMC requirements. General requirements Phytosanitary measures

5 The company: ORTO ALRESA Orto Alresa was born in Madrid Spain in 1.949, as a local manufacturer of laboratory equipment.62 years later, after a long road of effort, confidence and passion on its work, is a dynamic and innovative company which exports to more than 120 countries around the world, being present in biotech laboratories, research, environment, industrial, that makes them a reference as European manufacturers. In the search for new design trends and responses to consumer demand, Orto Alresa partners with universities, official centers and sector leading companies in order to produce equipment to suit any production or sample preparation. Innovative, functional and technologically advanced in the industry, to get shorter the gap between invention and utility. Orto Alresa is the present and especially future on centrifuges manufacturing, where the integration of quality and reliability with simplicity and performance are a top forward. OrtoAlresa Proposes: INNOVATION Producing a new idea of centrifuge, where the use friendliness allows the operator use the highest performances intuitively. This effort is reflected in the fact of being the first manufacturer to incorporate revolutionary TFT touch screen color on routine centrifuges, with a smart and simple design which can get the maximum performance and productivity. OA GREEN TECHNOLOGY. Respecting and protecting the environment by using materials consistent with this concept that allows our devices include more than 95% of recyclable parts, besides following the WEE directives for Waste Management of Electrical and Electronic Devices. Orto Alresa following Rosh Directive does not use hazardous substances in its manufacturing process. Incorporating HFC gases for refrigeration systems integrated into the centrifuges. Working only with quality packaging, which protects the shipment while reduces the space and are being 100% recyclable. This attitude is not understood as an extra effort, but as a way of positioning for the challenges ahead SERVICE Making the difference; enhancing a customer service management with a fast, efficient, and customized management. Finishing in production of products according the customer s needs and equipment for specific applications (OEM). For the installation, start up and repair of our equipment is supervised at all times by our technical department, offering training, telephone support and a fast delivery of components for repairs. To facilitate user access to our Technical Service through different custom channels, because the sale is only a means, not the end. A total warranty of 2 years for our products, without surprises. That upgrades the excellence of OrtoAlresa from beginning to the end in the manufacturing process. 5

6 CENTRIFUGES GUIDE MICROCEN 22 BIOCEN 22 BIOCEN 22R UNICEN 21 DIGICEN 21 DIGICEN 21R CONSUL 21 CONSUL 21R DIGTOR 21 DIGTOR 21R MAGNUS 21 MAGNUS 21R Universal High capacity guide SMALL MICRO BENCH TOP UNDER FLOOR

7 MAGNUS 21Y 21R DIGTOR 21 Y 21R CONSUL 21Y 21R MICROCEN 22 BIOCEN 22 Y 22R UNICEN 21 DIGICEN 21 Y 21R 7

8 SELECTION OF THE RIGHT EQUIPMENT Selection of the right equipment Aplications Tubes dimensions (mm) Microcen 22 Biocen 22 Biocen 22R Unicen 21 Digicen 21 / Digicen 21R Consul 21 / Consul 21 R Digtor 21 / Digtor 21R Magnus 21 / Magnus 21R Cell culture 86x128x Microtiter Plates 86x128x15/21/ /4/2 (2) 12/8/4 (2) 12/8/4 (2) 12/8/4 (2) Capillaries 1,5-3 x PCR Strips 0,2 ml. 6x ,2-0,4 ml 10x ,5-0,6 ml 8x ,5-2 ml 11x Cytocontainers ml 13x ml blood tubes 13x /10 ml blood tubes 13x ml 13x ml blood tubes 16x ml hs (1) 16x ml conical 17x ml 16x ml 25x ml hs (1) 25x ml conical 29x ml 35x ml hs (1) 29x ml 44x hs (1) 38x ml 48x ml 60x ml 61x ml 76x ml 80x ml 90x ml 96x (1) High speed tubes (2) Check plates dimensions Tubes dimensions and max capacity Some devices exert a high R.C.F. on the sample and its supports. One should check to confirm the manufacturer s specifications of the tubes. MaxR.C.F. allowed glass tubes xg.

9 Centrifuge value On a proper selection must be considered the RPM and RCF. MAX. SPEED (R.P.M) Angle fixed Swing out MICROCEN 22 BIOCEN 22 BIOCEN 22R UNICEN 21 Pag 12 Pag 14 Pag 16 Pag 18 DIGICEN 21 CONSUL 21 DIGTOR 21 MAGNUS 21 DIGICEN 21 R CONSUL 21 R DIGTOR 21 R MAGNUS 21 R Pag 22 Pag 28 Pag 34 Pag 40 Angle fixed Swing out MAX. F.C.R. (x g) 9

10 References tubes

11 REFERENCE TUBES Orto Alresa offer a wide range of tubes for centrifuges. Ref Capacity Shape Material Dimensions mm Cap Graduated ml TU flat bottom plastic 96x131 yes no TU cylindrical glass 90x120 no no TU flat bottom plastic 78x131 yes no TU cylindrical glass 80x118 no no TU flat bottom plastic 74X124 yes no TU cylindrical glass 75x118 no no TU cylindrical plastic 60x130 no no TU cylindrical glass 60x129 no yes TU cylindrical glass 60x130 no no TU cylindrical plastic 62x120 yes no TU cylindrical glass 60x120 no no TU cylindrical plastic 60x130 yes no TU cylindrical plastic 48x108 yes no TU cylindrical plastic 48x100 no no TU cylindrical plastic 40x115 yes no TU cylindrical glass 48x105 yes no TU conical glass 36-38x no yes TU cylindrical glass 44x130 yes no TU cylindrical glass 48x100 no no TU pear glass 58-59x no yes TU conical glass 44-46x no yes TU cylindrical glass 44x100 no no TU cylindrical plastic 38x112 yes no TU cylindrical plastic 34x96 no no TU cylindrical glass 34x110 yes no TU cylindrical glass 34x100 no no Ref Capacity Shape Material Dimensions mm Cap Graduated ml TU conical plastic 29x117 yes yes TU cylindrical plastic 34x100 no no TU cylindrical plastic 29x108 yes no TU cylindrical plastic 25x98 yes no TU cylindrical glass 24x100 no no TU cylindrical plastic 16x100 yes no TU cylindrical glass 16x110 no no TU conical glass 17x115 no si TU cylindrical plastic 16x100 no no TU conical plastic 17x122 yes yes TU conical glass 16x105 no yes TU cylindrical plastic 13x100 no no TU cylindrical plastic 16x100 yes no TU cylindrical plastic 16x80 yes no TU cylindrical plastic 13x84 yes no TU cylindrical glass 12x100 no no TU cylindrical plastic 13x75 no no TU cylindrical glass 10x100 no no TU 003 1,5-2 conical plastic 11x42 yes yes TU 002 0,5 conical plastic 8x30 yes yes TU 001 0,2 conical plastic 6x21 yes yes 11

12 Centrifuges: Microcen 22 MICROCEN 22

13 Why a small centrifuge must not be provided of mandatory standards about safety? The centrifuge Microcen 22 is a compact and practical device which meets the essential requirements that demand a reliable result in a short space of time. Operator can choose two different rotors for 8 x 15 ml conical or 12 x 5 ml, reaching RCF/ 6000 RPM. It s provided of safety systems essentials for a safety processing, with brushless engine maintenance free, unbalance switch off, chamber in stainless steel, lid lock motorized Ideal for run a reduced number of samples, it s undoubtedly the most appropriated choice for emergency labs, due to its reduce the time on sample preparation. Simplifies sample preparation. Use friendlinessly - LED screen shown RPM/RCF and time. - Intuitive handling through start, stops, short spin and play keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Acceleration and braking selectable by operator - Automatic open lid. - Last values remain on memory. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - Capacity 8 x 15 ml. - Speed, up to 3.663x g/6.000 RPM. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, Versions Ref Dimensions ( mm) ( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Accessories RT 225 RT 188 ROTOR ANGLE FIXED 30 ANGLE FIXED 30 Capacity 8x15 ml. 12x5 ml. R.P.M Radius mm R.C.F Breaking time (s) ADAPTERS ADAPTERS TUBES CAPACITY Dim (mm) TUBES REF. TUBES REF. 15 ml Ø 16x ml conical Ø 17x122 8 RE ml blood tubes Ø16x107 8 RE ml Ø 13x100 8 RE /10 ml blood tubes Ø 13x107 8 RE ml Ø13x75 8 RE ml blood tubes Ø 13x82 8 RE

14 Centrifuges: Biocen 22 Series BIOCEN 22

15 Very often the microcentrifuge user must consider the interactions between the tube and the sample, but... What about the interaction between the tube and the centrifuge? The Biocen 22 is designed to prevent contamination by interaction with the centrifuge and temperature increasing by: - Chamber stainless steel centrifuge easily sterilized. - Rotors with tight lids. - Ventilation system that helps reduce the temperature. Designed for small volume, allows 24 microtubes Centrifuge 2.2 ml, 32 ml of 0.2 up to 24 tubes of 1.5 x 75 mm, up to 15,000 rpm / 21,885 x g. Reduce spin time by controlling the different stages, allowing braking according to the type of sample. Optimizing the samples separation on a safe environment. Use friendlinessly - LCD screen shown RPM/RCF and time. - Intuitive handling through start, stops, short spin and lid keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Acceleration and braking selectable by operator - Automatic open lid. - Last values remain on memory. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - Capacity max : 24 x 2,2, ml. - Speed, up to x g/ RPM. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm) ( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Accessories RT 227 RT 228 (1) RT 229 ROTOR ANGLE FIXED 45 HORIZONTAL ANGLE FIXED 45 Max. capacity 24 of 1,5x2 ml. 24 of 1,5x75 mm. 32 of 0,2 ml R.P.M Radius mm R.C.F Braking time (s) ADAPTERS ADAPTERS ADAPTERS TUBES CAPACITY Dim (mm) TUBES REF. TUBES REF. TUBES REF. 1,5x75 mm. capillaries 1,5x microtubes 1,5-2 ml. 11x microtubes 0,5-0,6 ml. 8x30 24 RE microtubos 0,2-0,4 ml. 6x45 24 RE de 0,2 - (1) Includes microhaematocrit reader card 15

16 Centrifuges: Biocen 22 Series BIOCEN 22R

17 The Biocen 22 R can reach up to x g, becoming the necessary tool for most demanding labs. Usually microcentrifuges work with samples sensitive, valuables, or dangerous ( toxic, radioactive, infectious). Orto Alresa has built the Biocen 22 R with several advantages which allow a safe analysis, without interaction of centrifuge, as: - Cooling system which maintains the sample temperature at 4 C at max speed, regardless of the rotor. - Chamber of centrifugation in stainless steel, allowing an easy disinfection on samples leakages, avoiding contamination form the centrifuge. - Rotors with hermetic lids. - Accessories sterilizables. Use friendlinessly - LCD screen shown RPM/RCF,time, temperature and braking. - Intuitive handling through start, stop, short spin and lid keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Automatic rotor recognition. - Acceleration and braking selectable by operator memories and pre-cooling program. - Automatic open lid. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - Capacity Max.8 x 15 ml. - Speed, up to x g/ RPM. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. Cooling - Precooling program with rotor spinning and temperature selectable by operator. - 4 C at Max speed as higher. - Temperature range -20 C a 40 C. - Temperature sensor inside the chamber, gas R 404A HFC. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Regulation: 1005/2009 & 842/2006. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm) ( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Accesories RT 222 RT 223 RT 224 ROTOR ANGLE FIXED 45 ANGLE FIXED 30 ANGLE FIXED 45 Capacity 24 de 1,5x2 ml. 8 X 15 ml. 32 de 0,2 ml conical R.P.M Radius mm R.C.F Min.temp.max speed ( C) ADAPTERS ADAPTERS ADAPTERS TUBES CAPACITY Dim (mm) TUBES REF. TUBES REF. TUBES REF. 15 ml 16 x ml 13 x RE ml blood test 13 x RE ,57x75 mm. capillarie 1,5 x microtubes 1,5-2 m 11 x microtubes 0,5-0,6 ml 8 x RE microtubes 0,2-0,4 ml 6 x RE of 0,2-17

18 Centrifuges: Unicen 21 UNICEN 21

19 Universal, compact, versatile and quiet, are concepts which define the Unicen 21. Essential on demanding labs which need a reliable result on a short time, without scarifying the number of samples. Max capacity 4 x 100 ml, reach up to rpm/ x g, with 9 interchangeable rotors and up to 40 set of different adapters, covering the basical requirement on separation of clinics, industries, research centers, Speed and time are shown on digital displays easily readable, and lid can be open automatically at the end of the run, allowing to the operator a higher autonomy on routine process. It s provided of safety systems essentials for a safety processing, with brushless engine maintenance free, unbalance switch off, chamber in stainless steel, lid lock motorized Ideal for run a reduced number of samples, it s undoubtedly the most appropriated choice for emergency labs, due to its reduce the time on sample preparation. Simplifying separation. Use friendlinessly - LED screen shown RPM/RCF and time. - Intuitive handling through start, stops, short spin and play keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Acceleration and braking selectable by operator - Automatic open lid. - Last values remain on memory. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power(W) CE CE Features - Induction motor maintenance free - Max. Capacity 4 x 100 ml. - Speed, up to R.P.M. / x g. - Quiet: noise level < 60 db. 19

20 Accessories for centrifuges Unicen 21 Series RT 177 RT 175 RT 173 (1) RT 172 RT 226 RT 160 RT 161 Centrifuges: Unicen 21 ROTOR SWING OUT SWING OUT SWING OUT SWING OUT ANGLE FIXED 30 ANGLE FIXED 35 ANGLE FIXED 35 Capacity 8 x 15 ml. 4 x 50 ml. 4 x 100 ml. 2. KEROSEN 8 x 15 ml. 12 x 15 ml. 18 x 15 ml. R.P.M Radius mm R.C.F ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 100ml ø48 x RE ml. hs ø38 x RE ml. ø44 x RE ml. hs ø29 x RE RE ml. ø35 x RE RE ml. conical ø29 x RE RE ml. hs ø25 x RE RE ml. ø25 x RE RE ml. ø16 x RE RE ml. conical ø17 x RE RE ml. hs ø16 x 80 8 RE RE RE RE RE RE ml. ø13 x RE RE RE RE RE RE ml. blood tubes ø16 x RE RE /10 ml. blood tubes ø13 x RE RE RE RE RE RE ml. ø13 x 75 8 RE RE RE RE RE RE ml. blood tubes ø13 x 82 8 RE RE RE RE RE RE 303 Microtubes 1,5-2ml ø11 x RE RE (1) This rotor can be supplied with hermetic lids (RE 355)

21 RT 163 RT 167 ROTOR ANGLE FIXED 35 ANGLE FIXED 35 Capacity 24 x 15 ml. 6 x 50 ml. R.P.M Radius mm 132/ R.C.F / ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. 100ml ø48 x ml. hs ø38 x ml. ø44 x ml. hs ø29 x RE ml. ø35 x RE ml.conical ø29 x RE ml. hs ø25 x RE ml. ø25 x RE ml. ø16 x RE ml. conical ø17 x RE ml. hs ø16 x RE RE ml. ø13 x RE RE ml. blood tubes ø16 x RE 361 7/10 ml. blood tubes ø13 x RE RE ml. ø13 x RE RE ml. blood tubes ø13 x RE RE 364 Microtubes 1,5-2ml ø11 x RE

22 Centrifuges: Digicen 21 Series DIGICEN 21

23 The centrifuge Digicen 21 highlights for its versatility among the universal centrifuges and it s provided of: Swing out rotors for max 4 x 100 ml for tubes, microplates as well as microtubes. Angle fixed low speed up to 24 tubes of 15ml, Angle fixed low speed for microtubes up to 50 ml conical. It s controlled through LCD screen showing centrifugation values as time, RPM/RCF, as well as braking time, graphic for open lid, progress bar, messages and acoustic signals for error or end of program, which provides the user the process monitoring. Thinking on centrifugation. Use friendlinessly - LCD screen shown RPM/RCF,time, temperature and braking. - Intuitive handling through start, stop, short spin and lid keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Automatic rotor recognition. - Acceleration and braking selectable by operator memories. - Automatic open lid( non-refrigerated) - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Features - Induction motor maintenance free - Capacity Max. 4 x 100 ml. - Speed, up to x g/ RPM. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. 23

24 Centrifuges: Digicen 21 Series DIGICEN 21R

25 The centrifuge refrigerated Digicen 21 R can reach up to x g with a wide range of rotors; Swing out rotors, with a max volume of 4 x 100 ml which can fit several set of adapters for tubes with or without caps, microtubes, microplates. Angle fixed low speed for routine purposes. Angle fixed high speed from microtubes to 50 ml conical tubes. On LCD screen shown the selectable values as time, RPM, RCF, temperature and braking time as well as graphics for lid open, progress bar, and acoustic signals for a better control about the process by operator. Stabilizing sample preparation. Use friendlinessly - LCD screen shown RPM/RCF,time, temperature and braking. - Intuitive handling through start, stop, short spin and lid keys. - Rotor list on memory. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Automatic rotor recognition. - Acceleration and braking selectable by operator memories and pre-cooling program. - Automatic open lid( non-refrigerated) - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Cooling - Precooling program with rotor spinning and temperature selectable by operator. - 4 C at Max speed as higher. - Temperature range -20 C( -4 F) to 40ºC(104 F) - Temperature sensor inside the chamber, gas R 134A HFC. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Regulation: 1005/2009 & 842/2006. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) Z max aconsejable (Hz) CE < CE < Features - Induction motor maintenance free - Capacity Max.4 x 100 ml. - Speed, up to x g/ RPM. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. 25

26 Accessories for centrifuges Digicen 21 Series RT 143 RT 138 (1) RT 150 RT 183 RT 128 RT 151 (3) RT 110 Centrifuges: Digicen 21 Series ROTOR SWING OUT SWING OUT SWING OUT ANGLE FIXED HORIZONTAL ANGLE FIXED 45 ANGLE FIXED 35 Capacity 4 x 50 ml. 4 x 100 ml. 2,4 o 6 Microtiter 32 de 0,2 ml. 24 de 1,5x 75 mm. 24 de 1,5-2 ml. 24 x 5 ml. R.P.M Radius mm (4) 55 (4) R.C.F Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 100 ml. ø48 x RE ml. hs ø38 x RE ml. ø44 x RE ml. hs ø29 x RE RE ml. ø35 x RE RE ml. conical ø29 x RE RE ml. hs ø25 x 98 4 RE RE ml. ø25 x 96 4 RE RE ml. ø16 x RE RE ml. conical ø17 x RE RE ml. hs ø16 x 80 4 RE RE ml. ø13 x RE RE ml. blood tubes ø16 x RE RE /10 ml. blood tubes ø13 x RE RE ml. ø13 x RE RE ml. extr. blood tubes ø13 x 82 4 RE RE ,5 x 75 mm. capillaries ø1,5x microtubes 1,5-2 ml. ø11x39 12 RE RE RE microtubes 0,5-0,6 ml. ø8x RE microtubes 0,2-0,4 ml. ø6x de 0,2 ml RE x86x15 microtiter x86x21 microtiter x86x45 microtiter x86x22 cell culture (1) This rotor includes hermetic lids (2) Fitting this tubes rotor lid can not be closed (3) Check tubes features (4) Medium radio on bucket

27 RT 106 RT 108 RT 121 (3) RT 152 (3) RT 153 (3) RT 154 (3) ROTOR ANGLE FIXED 35 ANGLE FIXED 35 ANGLE FIXED 45 ANGLE FIXED 30 ANGLE FIXED 30 ANGLE FIXED 28 Capacity 18 x 15 ml. 24 x 15 ml. 6 x 50 ml. 12 x 10ml. Hermet 8 x 30 ml. Hermet 6 x 50 ml. Hermet R.P.M Radius mm / R.C.F / Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 100 ml. ø48 x ml. hs ø38 x ml. ø44 x ml. hs ø29 x RE ml. ø35 x RE ml. conical ø29 x RE ml. hs ø25 x RE RE ml. ø25 x RE RE ml. ø16 x RE RE RE ml. conical ø17 x RE RE 394 (2) 10 ml. hs ø16 x RE RE RE RE RE ml. ø13 x RE RE RE RE RE ml. blood tubes ø16 x RE RE 394 7/10 ml. blood tubes ø13 x RE RE RE RE ml. ø13 x RE RE RE RE RE RE ml. extr. blood tubes ø13 x RE RE RE RE RE RE 397 1,5 x 75 mm. capillaries ø1,5 x microtubes 1,5-2 ml. ø11 x RE RE 433 microtubes 0,5-0,6 ml. ø8 x microtubes 0,2-0,4 ml. ø6x x86x15 microtiter x86x21 microtiter x86x45 microtiter x86x22 cell culture

28 Centrifuges: Consul 21 Series CONSUL 21

29 High capacity on a bench top offering several advantages to the operator, until now exclusively available on devices for research. The TFT touch screen made easy the value selection, including in only one screen timer, RPM, RCF, acceleration and braking. The user menú, allows the customization of several values as open lid, RPM/RCF locking along centrifugation, countdown, etc. Along centrifugation a graphic shown the operator the current status as well as time to end of program. The devices included on Serie Consul 21 are highly functionals they can spin up to 4 x 400 ml, 48 tubes of 15 ml, 50 ml and 15 ml conical, microtubes, microplates, as well as a wide set of adapters for each one. Innovating about centrifugation. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 400 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories for programs. 29

30 Centrifuges: Consul 21 Series CONSUL 21R

31 High capacity on a bench top centrifuge which offer to their users several advantages, up to now only available on devices dedicated to research.the TFT touch screen simplifies the parameter selection; main values appear only in one screen as time, RPM, RCF, acceleration and braking. The operator menu allows other values adjustment as open lid once the rotor stops, locking RPM / RCF along the run, selection of time from 0 or at set RPM/RCF. Along centrifugation it showed on screen a graphic indicating its status as well as the stage of centrifugation, time to end of process. The devices included on Serie Consul 21 are highly functionalsthey can spi up to 4 x 400 ml, 48 tubes of 15 ml, 50 ml and 15 ml conical, microtubes, microplates, as well as a wide set of adapters for each one. Innovating about centrifugation. Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 400 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories + pre-cooling program. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). Cooling - Precooling program with rotor spinning and temperature selectable by operator. - 4 C at least at max speed with any rotor. - Range of temperature -20 C (-4 F) a 40 C(104 F) - Scale Celsius or Fahrenheit. - Temperature sensor inside the chamber. - Gas R 404A HFC. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Regulation: 1005/2009 & 842/2006. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) z Max. advisable CE < 0,446 CE < 0,446 31

32 Centrifuges: Consul 21 Series

33 Accesories for centrifuges Consul 21 Series RT 197 RT 198 RT 199 RT 206 RT 203 RT 205 (1) RT 219 ROTOR ANGLE FIXED 45 ANGLE FIXED 45 ANGLE FIXED 30 ANGLE FIXED 45 SWING OUT SWING OUT SWING OUT Capacity 8 x 50 ml. 4 x 100 ml. 4 x 250 ml. 30 x 1,5-2 ml. 4 x 250 ml. 4 x 400 ml. 12 microplacas R.P.M Radius mm R.C.F Min Temperature at max speed ºC ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 400ml. ø 80 x RE ml. ø76 x RE ml. ø 62 x RE RE RE ml. ø 60 x RE RE RE ml. ø 48 x RE RE RE RE ml. ø 44 x RE RE RE RE ml. ø 35 x RE RE RE RE RE ml. conical ø 29 x RE RE RE RE RE ml. ø 25 x 96 8 RE RE RE RE RE ml. ø 16 x RE RE RE RE RE ml. conical ø 17 x RE RE RE RE RE ml. blood tubes ø 16 x RE RE ml. ø 13 x RE RE RE RE RE ml. blood tubes ø 16 x RE RE RE RE RE /10 ml. blood tubes ø 13 x RE RE RE RE RE ml. ø 13 x RE RE RE RE RE ml. blood tubes ø 13 x 82 8 RE RE RE RE RE x 10 mm. ø 10 x RE RE RE RE RE microtubes 1,5-2 ml. ø 11 x RE RE RE RE RE RE 460 microtubos 0,5-0,6 ml. ø 8 x RE microtubes 0,2-0,4 ml. ø 6 x RE microplates 128x86x (1) This rotor can be supplied with hermetic lids (RE 405) 33

34 Centrifuges: Digtor 21 Series DIGTOR 21

35 The centrifuge Digtor 21 is a versatile device, allowing be present on routine labs, research, biotechnology, quality control, hospitals, etc. It is provided of several advantages as: - Innovation: with a TFT touch screen allowing operator the highest autonomy, controlling the separation, as well as a save energy system selectable. - Versatility: since 4 x 750 ml, 52 conical tubes of 15 ml, rotor for microplates, microtubes, and a wide range of adapters. - Safety: always shown on screen real values of RCF, based on accessories selection, automatically, no data introduction is required.accessories for bio containment. - Efficiency: Max RCF x g, selection of acceleration and braking time, depending of sample performances. Your best partner on lab. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 750 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories for programs. 35

36 Centrifuges: Digtor 21 Series DIGTOR 21R

37 The Serie Digtor 21 is formed from 4 devices highly functional, so that allow be present on routine labs, research, biotechnology, quality control The Digtor 21 R centrifuge is defined by several attributes as: - Innovation: its provided of TFT touch screen allowing higher automony to the operator as well as control the separation stages,and save energy system selectable. - Versatility: from 4 x 750 ml, 52 conical tubes of 15 ml, rotor for microplates, microtubes, and a wide range of adapter for each one. -Safety: It shows the real value of RCF based on accessories configuration, without introduce any parameter, as well as is provided of biocontainment accesories. -Efficiency: Max RCF x g, acceleration and deceleration time selectables, depending of sample features, dynamic cooling system which reduces the time to reach the selected temperature. Your best help in your lab. Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 750 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories + pre-cooling program. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). Cooling - Precooling program with rotor spinning and temperature selectable by operator. - 4 C at least at max speed with any rotor. - Range of temperature -20 C (-4 F) a 40 C(104 F) - Scale Celsius or Fahrenheit. - Temperature sensor inside the chamber. - Gas R 404A HFC. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Regulation: 1005/2009 & 842/2006. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) Z max advisable (Hz) CE < CE <

38 Accesories for centrifuges Digtor 21 Series RT 195 RT 192 RT 191 (1) RT 196 RT 197 RT 198 RT 199 Centrifuges: Digtor 21 Series ROTOR SWING OUT SWING OUT SWING OUT ANGLE FIXED ANGLE FIXED ANGLE FIXED 45 ANGLE FIXED Capacity 104 x 5 ml. 4 x 250 ml. 4 x 750 ml. 8 x 30 ml. 8 x 50 ml. 4 x 100 ml. 4 x 250 ml. R.P.M Radius mm R.C.F Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 750 ml. ø96 x RE ml. ø90 x RE ml. ø61 x RE RE RE ml. ø48 x RE RE RE RE ml. ø44 x RE RE RE RE ml. ø35 x RE RE RE RE RE ml. conical ø29 x RE RE RE RE RE ml. ø25 x RE RE RE RE RE ml. ø16 x RE RE RE RE RE RE ml. conical ø17 x RE RE RE RE RE RE ml. blood tubes ø16 x RE RE RE RE RE ml. ø13 x RE RE RE RE RE RE RE ml. blood tubes ø16 x RE RE RE RE RE RE 376 7/10 ml. blood tubes ø13 x RE RE RE RE RE RE RE ml. ø13 x RE RE RE RE RE RE RE ml. blood tubes ø13 x RE RE RE RE RE RE RE x 100 mm ø10 x RE RE RE RE RE RE x86x15 microtiter ø128x86x RE microtubes 1,5-2 ml. ø11x RE RE RE RE RE 440 microtubes 0,5-0,6 ml. ø8x microtubes 0,2-0,4 ml. ø6x (1) Avalaibles lids for that buckets (RE 356) (2) This rotor can fit adapters for blood bags (RE 308) (3) Medium radius on bucket (4) Fitting this adapters does not allow buckets lids

39 RT 206 RT 201 (1) (2) RT 202 ROTOR ANGLE FIXED 45 SWING OUT SWING OUT Capacity 30 x 1,5-2 ml. 4 blood bag 12 microtiter plates R.P.M Radius mm (3) R.C.F Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. 750 ml. ø96 x RE ml. ø90 x RE ml. ø61 x RE ml. ø48 x RE ml. ø44 x RE ml. ø35 x RE ml. conical ø29 x RE ml. ø25 x RE ml. ø16 x RE ml. conical ø17 x RE ml. blood tubes ø16 x RE ml. ø13 x RE ml. blood tubes ø16 x RE /10 ml. blood tubes ø13 x RE ml. ø13 x RE ml. blood tubes ø13 x RE x 100 mm ø10 x RE x86x15 microtiter ø128x86x RE microtubes 1,5-2 ml. ø11x RE RE 460 microtubes 0,5-0,6 ml. ø8x30 30 RE microtubes 0,2-0,4 ml. ø6x45 30 RE

40 Centrifuges: Magnus 21 Series MAGNUS 21

41 High capacity on a underfloor centrifuge which offer to their users several advantages, up to now only available on devices dedicated to research. The TFT touch screen Simplify the parameter selection; main values appear only in one screen as time, RPM, RCF, acceleration and braking. The operator menu allows other values adjustment as open lid once the rotor stops, locking RPM / RCF along the run, selection of time from 0 or at set RPM/RCF. Along centrifugation it showed on screen a graphic indicating its status as well as the stage of centrifugation, time to end of process, with graphi and values easily seeable from long distances, increasing the operator autonomy. The Magnus 21 can spin up to 4 x 750 ml,4 blood bags 72 tubes of 15 ml,16 tubes of 50 ml conical and 52 tubes of and 15 ml conical, microtubes, microplates, as well as a wide set of adapters for each one. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 750 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories for programs. 41

42 Centrifuges: Magnus 21 Series MAGNUS 21R

43 High capacity on a underfloor centrifuge which offer to their users several advantages, up to now only available on devices dedicated to research.the TFT touch screen simplifies the parameter selection; main values appear only in one screen as time, RPM, RCF, acceleration and braking. The operator menu allows other values adjustment as open lid once the rotor stops, locking RPM / RCF along the run, selection of time from 0 or at set RPM/RCF. Along centrifugation it showed on screen a graphic indicating its status as well as the stage of centrifugation, time to end of process. The devices included on Serie Magnus 21 are highly functionals, they can spin up to 4 x 750 ml,4 blood bags 72 tubes of 15 ml,16 tubes of 50 ml conical and 52 tubes of and 15 ml conical, microtubes, microplates, as well as a wide set of adapters for each one. Devoted to centrifugation. Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. - Short spin key with speed adjustable. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic open lid (only non-refrigerated). - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - High capacity: Max. Volume 4 x 750 ml. - High Speed, up to x g./ RPM. - Quiet: noise level < 60 db memories + pre-cooling program. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. - Viewing and calibration prot in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. - Forced ventilation which reduces the temperature increase (only non-refrigerated). Cooling (Magnus 21R) - Precooling program with rotor spinning and temperature selectable by operator. - 4 C at least at max speed with any rotor. - Range of temperature -20 C (-4 F) a 40 C(104 F) - Scale Celsius or Fahrenheit. - Temperature sensor inside the chamber. - Gas R 404A HFC. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Regulation: 1005/2009 & 842/2006. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) Z max advisable (Hz) CE < CE <

44 Accesories for centrifuges Magnus 21 Series RT 195 RT 192 RT 191 (1) RT 196 RT 197 RT 198 RT 199 Centrifuges: Magnus 21 Series ROTOR SWING OUT SWING OUT SWING OUT ANGLE FIXED ANGLE FIXED ANGLE FIXED 45 ANGLE FIXED Capacity 104 x 5 ml. 4 x 250 ml. 4 x 750 ml. 8 x 30 ml. 8 x 50 ml. 4 x 100 ml. 4 x 250 ml. R.P.M Radius mm R.C.F Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. Tubes REF. 750 ml. ø96 x RE ml. ø90 x RE ml. ø61 x RE RE RE ml. ø48 x RE RE RE RE ml. ø44 x RE RE RE RE ml. ø35 x RE RE RE RE RE ml. conical ø29 x RE RE RE RE RE ml. ø25 x RE RE RE RE RE ml. ø16 x RE RE RE RE RE RE ml. conical ø17 x RE RE RE RE RE RE ml. blood tubes ø16 x RE RE RE RE RE ml. ø13 x RE RE RE RE RE RE RE ml. blood tubes ø16 x RE RE RE RE RE RE 376 7/10 ml. blood tubes ø13 x RE RE RE RE RE RE RE ml. ø13 x RE RE RE RE RE RE RE ml. blood tubes ø13 x RE RE RE RE RE RE RE x 100 mm ø10 x RE RE RE RE RE RE x86x15 microtiter ø128x86x RE microtubes 1,5-2 ml. ø11x RE RE RE RE RE 440 microtubes 0,5-0,6 ml. ø8x microtubes 0,2-0,4 ml. ø6x (1) Avalaibles lids for that buckets (RE 356) (2) This rotor can fit adapters for blood bags (RE 308) (3) Medium radius on bucket

45 RT 206 RT 201 (1) (2) RT 202 ROTOR ANGLE FIXED 45 SWING OUT SWING OUT Capacity 30 x 1,5-2 ml. 4 blood bag 12 microtiter plates R.P.M Radius mm (3) R.C.F Min Temperature at max speed C ADAPTERS ADAPTERS ADAPTERS Dim (mm) Tubes REF. Tubes REF. Tubes REF. 750 ml. ø96 x RE ml. ø90 x RE ml. ø61 x RE ml. ø48 x RE ml. ø44 x RE ml. ø35 x RE ml. conical ø29 x RE ml. ø25 x RE ml. ø16 x RE ml. conical ø17 x RE ml. blood tubes ø16 x RE ml. ø13 x RE ml. blood tubes ø16 x RE /10 ml. blood tubes ø13 x RE ml. ø13 x RE ml. blood tubes ø13 x RE x 100 mm ø10 x RE x86x15 microtiter ø128x86x RE microtubes 1,5-2 ml. ø11x RE RE 460 microtubes 0,5-0,6 ml. ø8x30 30 RE microtubes 0,2-0,4 ml. ø6x45 30 RE

46 DIGTOR 21C Centrifuge for petroleum and derivates Special applications

47 The Digtor 21 C have been specially designed for water and sediment determination, as well as characterization of used oils and petrol features as demulsibility and precipitation. A choice of accessories for spin cylinder-conical tubes of 6 and 8 inches, pear shaped of 6 inches as well as finger tubes od 12,5 ml. It can apply the following standards: ASTM D 91, D96, D 893,D 1796, D2273,D2709, D 2711, D 4007, D 5546, API 2542, API 2548, BS 4385, ISO 3734, ISO Use friendlinessly - TFT touch screen easy to read and values selection. - Informative Wheel about the progress of stages of centrifugation - Rotor and adapters list on memory. - Real values on screen of RCF based on accessories configuration. - Timer count up/down, from 0 or at set RPM/RCF for test reproducibility. From 0 to 60 minutes, in 1 minute steps, and hold position. - Up to 175 acceleration ramps and up to 175 braking ramps. - Automatic rotor recognition. - Lid latch lock. - Microprocessor controlled. - Option: free or locked adjustment of RPM/RCF along the run. Features - Induction motor maintenance free - High Speed, up to RPM/ RCF. ( 10 RPM steps) - Quiet: noise level < 60 db memories + pre-heating programs. Safety - Optional : gas release system. - Isolation for reducing the heat loss. - Lid locking and holding. - Imbalance switch off. - Manual overriding, and lid dropping protection. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. Heating - Preheating program with rotor spinning and temperature selectable by operator. - Temperature regulation from room +5 C up to 70 C (158 F). - Scale Celsius or Fahrenheit. - Temperature sensor inside the chamber. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Accessories RT 213 RT 220 ROTOR SWING OUT SWING OUT Capacity 4x100 ml. (6 ) 4x100 ml. (8 ) R.P.M. MAX Radius mm RCF MAX ADAPTERS ADAPTERS Dim (mm) TUBES REF. TUBES REF. ASTM Conical 6 Ø 44x162 4 RE ASTM Pear Ø 58x157 4 RE ASTM Conical 8 Ø 36x Finger tubes 12,5 ml Ø 16x RE RE 455 Finger tubes 12,5 ml Ø 16x RE

48 Special applications CITOCENTRIFUGE Centrifugation on thin layer

49 The cytocentrifuge Digicen 21 have been designed for concentrate biological samples on a slide for identification and characterization on microscope. It s provided of a swing out rotor for 4 buckets which depending of their location on rotor, allow the filtrated recovery for further processing. Besides it can be fitted with rotors for tubes, microplates or microtubes. Easy to use which reduces the handling time, essential features on oncology, virology, cytology, hematology and microbiology laboratories. Use friendlinessly -Disposables sealed that avoid samples leakages. - One rotor RT 207 for 4 cytocontainers. - Quick microorganism identification. - Cells detection even low concentration. - Save on consumables and time (< 15 min) - LCD screen shown RPM/RCF, time, temperature and braking. - Intuitive handling through start, stop, short spin and lid keys. - Automatic rotor recognition. - Acceleration and braking selectable by operator... - Automatic open lid (non-refrigerated) - Lid latch lock. - Microprocessor controlled, 16 memories - Option: free or locked adjustment of RPM/RCF along the run. - Chamber of centrifugation in stainless Steel. - Viewing and calibration port in the lid. - Several messages keep the operator informed about the device situation. - Guard ring between the chamber of centrifugation and the housing. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :20006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) CE CE Accessories - Only one rotor RT 207 for 4 citocontainers. - Capacity 4 x 2 ml - Max speed RPM/839 FCR (x g). - Surface on slide: 6,2 mm or 8,7 mm de diámetro. Features - Induction motor maintenance free - Quiet: noise level < 60 db. Safety - Warning for avoid samples drying each 20 seconds. - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. 49

50 LACTER Determination of fat in dairy products Lacter centrifuge have been designed for fat determination on dairy products (cheese, milk, cream, butter), according Gerber Method guidelines. Its provided of heating which enhances the separation of fat and aqueous phase, and 2 rotors for 8 or 12 butyrometers for different products, which allows a direct reading on tube. Use friendlinessly - Controlled by microprocessor.. - Built in time from 0 to 60 and hold position. - Speed fixed to RPM / 225 x g. - Temperature fixed to 65 C(149 F). - Temperature on digital display. Features - Quiet motor. - Quiet: noise level < 60 db. Safety - Lid locking and holding as well as lid dropping protection. - Imbalance switch off. - Manual overriding. - Chamber of centrifugation in stainless Steel. EC Directives: 98/79/EC, 2006/95/EC, 2004/108/EC; 2002/95/EC, 2002/96/EC, 2003/108/EC. Standards: :2002, :2006, :2006 Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) Heating CE SI CE NO RT 122 RT 101 Special applications Accessories ROTOR ANGLE FIXED 20 ANGLE FIXED 20 Capacity 8 pruebas 12 pruebas R.P.M Radius mm - - RCF MAX Butirómetros Max dimensions 25 x

51 TISSUE REGENERATION Centrifuges for tissue regeneration: Platelets and adipose Discovery of big potential of some tissues as peripheral blood or fat, have enhanced the development of several applications on tissue regeneration on traumatology, ophthalmology, dermatology, aesthetic surgery, ect. That devices are under in Vitro diagnostic (IVD) Directive and are provided of all safety systems for operator and sample, as habitual in Orto Alresa centrifuges (chamber in stainless steel, lid locking and holding, controlled by microprocessor, induction motor, unbalance switch off). Platelet concentrates The PRGFCen have been designed for reach concentrates of platelet easily and efficiently. Once the concentrate is processed, the surgeon can regenerate several kind of matrix as functional as the surrounding tissue. It has a swing out rotor for 8 tubes of 5 ml, and by RPM / RCF control we can reach a the right concentration depending of the volume of the tube to spin, without accessories exchange. Easy to use, sterilizable accessories, and low Boise level, made it proper for work on operating rooms. PRGF Cen + RT 216 Digtor 21 Col + RT 210 Fat concentrates On peripheral tissues, the fat is the one which has higher stem cells concentrates. It s extraction and concentration can be an easy process: sample on extraction syringe ( 50 or 60 ml)can be spin and in only 5 minutes, we will reach a clean tissue, which avoid the body rejection, easily moldable, and its effects can be see immediately. It has a rotor for 4 syringes of 60 / 50 ml, and adapters for 10 ml syringes, for small surfaces. 51

52 Autoclaves & distillers ECOCLAVE PLUS S & ECOCLAVE PLUS B

53 Its belong to the Class B. The Ecoclave plus B distinguish as a versatile device and easy to use. It has 12 programs predefined for simple processing on daily routine. Accessories includes: tray holder,4 trays, key for door/tray extractor, 2 hoses,sponge and funnel. Optional Printer. Features - It is proper for esterilization of wrapped unwrapped, porous, hollow and solid. - Capacity 18 y 23 litres. - Icons on screen for lid lock, on process,water levels and kind of cycle. - Lid lock system with triple safety system. - Steam entry direct to the chamber. - Adjustable to deionzation water systems. - Vacuum with double stage vacuum pump, before and after sterilization. - Residual humidity <2%. Use friendlinessly - Ecoclave Plus S: 2 Test Cycles: Bowie & Dick, Vacuum Test.Vacuum pre and post sterilization. - Ecoclave Plus B:3 Test Cycles: Bowie & Dick, Hellix test, Vacuum Test.Vacuum fractionated. - Number of cycles with full tank: Class S: 10 for18 L, 8 for 23 l. Clase B:8 for 18 l, y 6 for 23 l. - Weight: packed: 18 l 3 Kg, 23 l 4,5 Kg. Unpacked : 18 l 4 Kg, 23 l 6 Kg. Porous: 18 l 1Kg (B) /0,5 Kg (S),23 l 1,5 Kg ( B)/1 Kg ( S). - LCD screen with temperature, time of sterilization and drying, pressure inside the chamber, program and cycle stage. - Night Cycle. - Initial check and tracking througherror messages on screen. - Chamber on stainless steel. - Filing with vacuum pump. - Memory Test System (MTS):store 10 cycles and print out. Safety - Electrical: earthed point. Fuses. - Safety valve for pressure. - Safety valve for leakages. - Bacteorologic filter for air entry after sterilization. - Vacuum pump for erase air burbles before sterilization and drying. - Double tank for water avoiding recycling. European directives EC 93/42,EN 13060, EN Versions Ref Dimensions ( mm)( w x d x h ) Net weight (Kg) Trays dimensions (mm) Class Power (W) Chamber Testscycle volume(l) AU x 340 B B+V+H AU x 440 B B+V+H AU x 340 S B+V AU x 440 S B+V ATTENTION: for 23 liter models drying time lasts 5 minutes, total time 15 min. THIS AUTOCLAVE CAN NOT STERILIZE LIQUIDS. B= Bowie & Dick V=Vacuum Test H=Helix Programs Sterilize instruments and equipment Cycle test Cycle test Hollow, delicate, hollow stainless steel, turbine Hollow stainless steel, turbine Rubber solid, solid delicate Rubber solid and metal solid. Hollow stainless steel and metal instruments Type of cycle Bowie & Dick test Vacuum test Ecoclave Plus S Total Type of time cycle (min) Ecoclave Plus B Total Type time of (min) cycle Wrapped N of vacuum phase S N of vacuum phase B 30 Test 35 Test Test 15 Test C 45 S 43 B SI C 38 S 40 B SI C 43 S 43 B SI C 30 S 35 B SI 2 2 PRION (134) 50 S 50 B SI porous 121 C 48 S 51 B NO porous 134 C 45 S 55 B SI 2 4 Rubber solid 121 C 38 S 33 S NO 2 2 and solid delicate. quick Rubber solid and metal solid. 134 C rápido 28 S 25 S NO 2 2 Hollow stainless steel 134 C Open Hollow 30 S 30 S NO

54 Autoclaves & distillers DISTILLER

55 The Orto Alresa distillers permits the provision of distilled water from main water with properties suitable for use in other equipment, preparation of solutions, etc. Allows major savings in the amount of water through the proper control of the flow of the refrigeration water. Accessories Ref Descripción PP 385 Tank for 25 litres made in plastic wide mouth 53 mm. Features - Inner in stainless steel, AISI 304 housing on steel treated to epoxy. - Small footprint. - High quality distillation. - Conductivity : 2.5 Microsiemens/cm. - Resistivity: 0,4 megaohms/ cm (at 20 C). Versions Ref Dimensions ( mm) ( w x d x h ) Net weight (Kg) Voltage (V) Frecuency (Hz) Power (W) Capacity ( l) Refrigeration water(l) Use friendlinessly - Keypad with main switch and temperature selector. - Entry water tube can be fitted the entry water connector. - Draining connector to the refrigerationwater could be fitted to several tanks. DA DA DA Safety - Liquid level probe which switches on the stop by low water flow. - Electrical: earthed. - Sealed by silicon rubber. - Safety system with hidraulic temperature control. Community directives: 2006/95/EC 2004/108/EC, 2006/42/EC Standards :EN :93, EN :92 & EN Normas: EN :2002 EN :92 y EN :94. 55

56 Ball Mill BALL MILL

57 The Ball Mill produces the breaking up by the beating of the balls against the sample as it follows a semicircular orbit dragged around the jar by the motor cylindre. Isolated jars J prevent the sample contamination. Its design and function makes it suitable for grinding tasks in laboratories, public works, paint manufacturing, ceramics, preparation of feedstock for pharmaceutical products, foodstuffs. Features - High resistance cylindres: inner in steel and outer flexible for run the jars carefully. - Metalic housing treated for large resistance. - Main switch ON/OFF iluminated. - Time selectable up to 99 hours, or hold position. Use friendlinessly - Emergency stop. - Cylindres length up to 700 mm. - Capacity 1 jar of 15 litres,1 jar of 11 litres, 2 jars of 5 litres, 3 jars of 3 litres, 4 jars 1 litre. - Jars avalaibles in alumina or in stainless steel. - Microprocessor controled. - Jar speed selectable from 50 to 300 RPM, or jar (diameter dependent). Versions Ref Monophasic Voltage (V) Accessories Exterior dimensions ( w x d x h) Jars made in stainless steel Power (W) Frecuency (Hz) Net weight (Kg) ML / /60 72 ML / /60 72 Jars made in alumina 15 litres 11 litres 5 litres 3 litres 1 litre 1 litre 3 litres 5 litres PI 226 PI 225 PI 064 PI 063 PI 062 PV 035 PV 036 PV 037 PI 226 PI 225 PI 064 PI 063 PI 062 PV 035 PV 036 PV 037 Safety - Electrical earthed. Fuses. - Main switch. - Cover for rollers. - Safety lid:rolls stops when it is open. Community directives:2004/108/ec 2006/42/EC, 2006/95/EC Standards : EN EN

58 Sieves Shaker SIEVES SHAKER SIEVES

59 The analytical sieve shaker OASS203 allows the reproducibility, according to ISO 9001 for control and measuring devices. Therefore, they are essential on research and quality control labs for industries along its manufacturing procedures. Some properties as mechanical strength, agglomeration due to adhesive forces, mixability, stress behavior, organoleptic properties, can be defined by using AOSS203. Features -Sample capacity: up to 6 Kg. -Sieving 3 D movement. -Proper for wet and dry analysis. -Controlled by microprocessor. Versions Ref Dimensions outer ( w x d x h) Power (W) Voltage (V) Frecuency (Hz) Weight (Kg) TA ,5 TA ,5 Use friendlinessly -Sieving power selectable (100% to RPM), allowing a greater dispersion of the sample through the sieve and bigger efficiency of the process. -Programmable up to 16 memories, time selectable from 10 second to 99 minutes and hold position. - Interval selection from 1 to 99 seconds. Safety - Extremely quiet, has the lowest noise level available in the market - Housing of high resistance and stability. -Electrical protection: Earthed fuses. Accessories -Sieves on stainless Steel AISI 316 for metallic mesh y AISI 304 for perforated plates, all of them provided of a rubber join for a better fitting, unalterable marking by laser. -Sieves diameter: 203 mm (8 ) & 200 mm. -Max capacity: 8 pieces of 50 mm height or 16 of 25 mm, total height of set of sieves 400 mm. -Range of particles size: 20 µ a 125 mm. -Calibration certificate available. Community directives:2006/42/ec, 2006/95/EC, 2004/108/EC. Standards: EN , EN 61326, EN

60 Accessories for Sieves Shaker Sizes available: 200 mm Ø x 50 mm (h), 200 mm Ø x 25 mm (h), 203 ( 8 ) mm Ø x 50 mm (h), 203 mm ( 8 ) Ø x 25 mm (h). Stainless Steel AISI 316 for metallic mesh and AISI 304 for perforated plates. Max capacity: 8 sieve 50 mm of height or 16 of 25 mm of height. Sieves Shaker Sieves made stainless steell (200 x 50 mm ) Standard ISO : Perforated plates Standard ISO : Metalic mesh Ref Opening size (mm) Ref Opening size (mm) PI PI PI PI PI PI PI PI PI Pl PI PI PI Pl PI PI PI Pl PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI PI 066 Receiver PI 067 Cover PI 351 Receiver wet system PI 350 Covert wet system Sieves made in stainless steel 8 (203 x 50 mm) Standard ASTM E323: Perforated plates Standard ASTM E11: Metalic mesh Ref Opening size Ref Opening size PI PI 177 No. 7 PI 151 4,24 PI 178 No. 8 PI PI 179 No. 10 PI ½ PI 180 No. 12 PI PI 182 No.16 PI ½ PI 181 No. 14 PI PI 183 No.18 PI PI 184 No. 20 PI ¾ PI 185 No.25 PI ½" PI 186 No. 30 PI ¼ PI 187 No. 35 PI PI 188 No. 40 PI PI 189 No. 45 PI 163 7/8 PI 190 No. 50 PI 164 ¾ PI 191 No. 60 PI 165 5/8 PI 192 No.70 PI PI 193 No.80 PI 167 ½ PI 194 No.100 PI 168 7/16 PI 195 No.120 PI 196 No.140 Norma ASTM E11: Metalic mesh PI 197 No.170 Ref Opening size PI 198 No.200 PI 169 3/8 PI 199 No.230 PI 170 5/16 PI 200 No. 270 PI PI 201 No.325 PI 172 ¼ PI 250 No.400 PI ½ PI 202 Cover PI 174 No. 4 PI 203 Receiver PI 175 No. 5 PI 221 Cover wet system PI 176 No. 6 PI 235 Receiver wet system

61 BAR-SPIN Bar -Spin allows the stirring of volumes up to 20 liters (relative to water). Provided with a large range of accessories which allow the proper homogenization of the liquid. Features Stirring speed variable form 200 to 2000 RPM. Housing injected of high resistance. 2 versions availables of 20 y 50 W with or without tachometer..fastening double nut on the back of device..max viscosity mp a.s. -Provided with standard rod 8 x 300 mm with a blade of 80x20 mm (only AG 011 and AG 012) Use friendlinessly Electronic regulation of speed. Fastening located at the back. Rods of up 10 mm. Universal clamp which for a quick and easy rod replacement. Safety Electrical: earthed. Fuses. Community directives: 2006/42/EC,2004/108/EC, 2006/95/EC Standards :EN :2001, EN :2006. Versions Ref Control Stirring capacity (l) Power (w) Dimensions outer ( mm) ( w x d x h) Regulation speed Net weight AG003 Analogical AG004 Digital Electronic 4 AG011 Analogical Bulb 4.5 thermostat (precission +/-3ºC) AG012 Digital Digital Programer (PID+/-0.5%) 4.5 Accesories Ref AG003 AG004 AG011 AG012 15x750 mm PC x750 mm PC 203 PI 136 PI 137 PI 138 PI 243 PI 244 PI

62 Baths & Inmersion Thermostats THERBA & THERBA D

63 Thermostatic baths from 5 to 21liters a temperature range covering from room +5 C to 120 or 200 C depending on the model. Give their versatility with regard to uses, they can be used to maintain the temperature on liquid foodstuffs, biological fluids, incubation, as well as to increase the temperature within their working values (catalysis, material testing, ). Features Double body, exterior steel treated with anti-oxidant and interior made in stainless, steel 18/10. - Anti-splash design. - Temperature control by bulb thermostat,or digital, depending on the version. - Lighting main switch ON/OFF - Controled by microprocessor. - Heating by shielded heating element made in stainless steel AISI Temperature precission 0.1 C ( only Therba D) Safety - Low liquid level probe which stop the heating element by low liquid level. - Electrical: earthed and fuses. - Safety thermostat that has a manual reset in the event of over-temperature DIN Class 2. - Heating element operation indicator. - Safety thermostat operation indicator. Community directives:2006/95/ec 2006/42/EC, 2004/108/EC. Standards: EN :2001 EC :2006. Versions Ref Control Capacity (l) Max. Temp. ( C) Power (w) Dimensions ext. ( mm) ( w x d x h ) Weight (Kg) Precission Probe end of scale ( C) Probe BA002 Analogical /-1 - BA003 Analogical /-2 - BA004 Digital /-0,5 PTC BA005 Digital /-1 Pt100 BA006 Analogical /-1 - BA007 Analogical /-2 - BA008 Digital /-0,5 PTC BA009 Digital /-1 Pt100 BA010 Analogical /-1 - BA011 Analogical /-2 - BA012 Digital /-0,5 PTC BA013 Digital /-1 Pt100 Accessories Ref BA002 BA003 BA004 BA005 BA006 BA007 BA008 BA009 BA010 BA011 BA012 BA013 PI 118 PI 119 PI 120 PI 121 (2 holes) PI 122 PI 123 PI 124 PI 125 (4 holes) PI 126 PI 127 PI 128 PI 129 (6 holes) PI 147 (1 max) PI 148 (máx 2) PI 149 (1 max) PI 204 PV 058 PI 204 PV 058 PI 204 PV

64 Baths & Inmersion Thermostats INMER & INMER P