Enhanced optical absorptance of metals using interferometric femtosecond ablation
|
|
- Junior Jones
- 6 years ago
- Views:
Transcription
1 Enhanced optical absorptance of metals using interferometric femtosecond ablation K. Paivasaari, J. J. J. Kaakkunen, M. Kuittinen and T. Jaaskelainen Department of Physics and Mathematics, University of Joensuu, P.O.Box 111, Joensuu 80101, Finland. Abstract: The enhanced optical absorptance in metals was recently demonstrated using femtosecond laser-induced surface structuring. This structuring was obtained by simply focusing the light to the sample surface. Here we demonstrate more efficient absorptance enhancement using interferometric ablation. This interferometric ablation technique produces deeper surface structures and, consequently, higher absorption than structures obtained by just focusing the light to the surface. We also show the measured reflectance spectra over visible region for unaltered and structured stainless steel and copper samples Optical Society of America OCIS codes: ( ) Laser materials processing; ( ) Microstructure fabrication. References and links 1. A. Y. Vorobyev and C. Guo, Enhanced absorptance of gold following multipulse femtosecond laser ablation, Phys. Rev. B 72, (2005). 2. A. Y. Vorobyev and G. Guo, Shot-to-shot correlation of residual energy and optical absorptance in femtosecond laser ablation, Appl. Phys. A 86, (2007). 3. A. Y. Vorobyev and G. Guo, Effect of nanostructure-covered femtosecond laser-induced periodic surface structures on optical absorptance of metals, Appl. Phys. A 86, (2007). 4. A. Y. Vorobyev and C. Guo, Direct observation of enhanced residual thermal energy coupling to solids in femtosecond laser ablation, Appl. Phys. Lett. 86, (2005). 5. A. Y. Vorobyev, V. M. Kuzmichev, N. G. Kokody, P. Kohns, J. Dai and G. Guo, Residual thermal effects in Al following single ns- and fs-laser pulse ablation, Appl. Phys. A 82, (2006). 6. A. Y. Vorobyev and G. Guo, Enhanced energy coupling in femtosecond laser-metal interactions at high intensities, Opt. Express 14, (2006). 7. A. Y. Vorobyev and C. Guo, Femtosecond laser nanostructuring of metals, Opt. Express 14, (2006). 8. A. Y. Vorobyev, V. S. Makin and C. Guo, Periodic ordering of random surface nanostructures induced by femtosecond laser pulses on metals, J. Appl. Phys. 101, (2007). 9. J. Wang and C. Guo, Ultrafast dynamics of femtosecond laser-induced periodic surface pattern formation on metals, Appl. Phys. Lett. 87, (2005). 10. D. Maystre and R. Petit, Brewster incidence for metallic gratings, Opt. Commun. 17, (1976). 11. E. Popov, Total absorption of light in metallic gratings: a comparative analysis of spectral dependence for shallow and deep grooves, J. Mod. Opt. 36, (1989). 12. F. J. Garcia-Vidal, J. Sanchez-Dehesa, A. Dechelette, E. Bustarret, T. Lopez-Rios, T. Fournier and B. Pannetier, Localized surface plasmons in lamellar metallic gratings, J. Lightwave Technol. 17, (1999). 13. A. A. Maznev, T. F. Crimmins and K. A. Nelson, How to make femtosecond pulses overlap, Opt. Lett. 23, (1998). 14. T. Kondo, S. Matsuo, S. Juodkazis and H. Misawa, Femtosecond laser interference technique with diffractive beam splitter for fabrication of three-dimensional photonic crystals, Appl. Phys. Lett. 79, (2001). 15. Y. Nakata, T. Okada and M. Maeda, Lithographical laser ablation using femtosecond laser, Appl. Phys. A 79, (2004). (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13838
2 16. R. Bruer and O. Bryngdahl, Electromagnetic diffraction analysis of two-dimensional gratings, Opt. Commun. 100, 1 5 (1993). 17. E. Noponen and J. Turunen, Eigenmode method for electromagnetic synthesis of diffractive elements with three-dimensional profiles, J. Opt. Soc. Am. A 11, (1994). 18. L. Li, New formulation of the Fourier modal method for crossed surface-relief gratings, J. Opt. Soc. Am. A 14, (1997). 1. Introduction Recently, it was found that the femtosecond laser generated surface structures enhance the optical absorptance of various metals [1, 2, 3]. Vorobyev et.al. discovered the enhanced energy coupling in femtosecond laser-metal interactions [4, 5, 6]. This enhancement is due to spontaneous generation of nano- and micro-structures and laser-induced periodic surface structures (LIPSS) when surface is repeatedly illuminated with femtosecond laser using sufficient fluence [7, 8, 9]. This phenomenon of enhanced absorptance in metals, sometimes referred as black metal, is believed to have applications in many fields such as sensor technology. However, manufacturing of this black metal by simply focusing the femtosecond light to the sample surface is rather time-consuming. In this paper we propose more controlled and faster method to alternate the absorptance of metals. Instead of waiting the structures to appear spontaneously under the femtosecond illumination, the surface can be ablated using interference pattern in order to generate the desired structures. We will demonstrate increase in absorption of the metal that is ablated using four beam interference pattern creating hole-array structure to the surface. The absorptance changes using such interference pattern for illumination are greater than ones obtained by just focusing the light onto surface using the same pulse numbers and average fluences. Furthermore, this is the first demonstration of the grating structure in metals acting as a total absorber over the whole visible region of the spectrum. Previously total absorption was obtained using metal gratings due to the surface plasmon generation [10, 11, 12]. Total absorption related to the surface plasmons have a resonant nature and can be obtained only using sub-wavelength grating periods and only for specific incident angle and polarization state of the light. Here absorption is independent of the incident angle and polarization state of the light. Total absorption is obtained for steel sample using grating period of 2 μm. Measured reflectance spectra for structured stainless steel and copper samples over nm range are presented. 2. Experiments Laser used in the experiments was CPA Tissa 50 Ti:sapphire oscillator and amplifier system providing 1 mj pulse energy with repetition rate of 50 Hz at 800 nm central wavelength. Fig. 1. Interferometric ablation set-up. The interferometric ablation set-up is shown in Fig. 1. The femtosecond beam is divided to four beams using a diffractive optical element (DOE) and imaged to the sample using confocal system consisting of two lenses. The period of the interference pattern resulting from such (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13839
3 set-up can be calculated by formula d = MΛ/2, where M = f 2 / f 1 is magnification of the lens system and Λ is the grating period of the DOE. Period of Λ =15μm was used here. Lenses used here were double-convex lenses with focal lengths f 1 = mm and achromatic lens with f 2 = 30 mm. The period of the interference pattern resulting from such set-up was from 1.5 to 2.25 μm. The combination of DOE and confocal imaging system ensures that the femtosecond pulses overlap over their entire cross section on the sample [13]. This makes it possible to ablate large areas while using rather large intersection angles between the beams on the sample. This interferometric ablation setup is also described in details in Refs. [14, 15]. For comparison to the structures produced using interferometric setup, we also generated absorption enhancing surface modifications using traditional method [2, 5]. For this the femtosecond laser light is focused at normal incident to the surface so that the ablated spot size is equal to the one used in the intererometric set-up. Fig. 2. Structured surface using direct focusing of femtosecond light to the steel sample. Structures obtained using 200 pulses with average fluence of 0.2 J/cm 2. The polarization of light was linear and oriented vertically. Fig. 3. Structured surface using interferometric femtosecond ablation on the steel sample. Structures obtained using 200 pulses with average fluence of 0.2 J/cm 2.The polarization of light was linear and oriented vertically. The mechanically polished steel and copper surfaces were used as a sample materials. A 4 4mm 2 area of structured surface was manufactured by moving beam with diameter of 350 μm over the sample surface using stop-motion technique so that the ablated spots slightly overlap on the edges. In results presented here, the number of pulses on one spot was 200. The average fluence was 0.2 J/cm 2. Here the average fluence is defined as used energy divided by ablated surface area. Note, that although the average energy per unit area is same for both techniques, the peak fluence is four times higher using interferometric ablation. This enables formation of deeper surface structures and consequently higher absorptance. Figure 2 shows the (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13840
4 nanostructures and LIPSS generated on the stainless steel sample using focused light and above mentioned fluence and pulse number. In Fig. 3 are shown corresponding structures obtained using interferometric setup. The hole-array structures are clearly deeper than nanostructures obtained using direct focusing due to higher peak fluence when using interferometric ablation. The depth of the holes appears to be essential for our sample to act like an absorber. Using fewer pulses and consequently shallower holes, the structures act as a normal diffraction grating, but when holes get deeper the surface stops diffracting and starts absorbing. The holes shown in the Fig. 3 are approx. 2.5 μm deep. The changing of the grating period from 1.5 to 2.2 μm does not bring any radical changes to the absorptance enhancement. The reflectance spectrum of the modified sample surface was obtained using a Perkin-Elmer Lambda 18 spectrophotometer together with Labsphere RSA-PE-18 integrating sphere. The use of the integrating sphere allowed us to compare the reflectance spectra of the polished surface with specular and structured surface with diffuse reflection. In Fig. 4 are shown the measured reflectance spectra for polished stainless steel sample and surfaces shown in the Figs. 2 and 3. From the figure one can see that by using the interferometric ablation the steel can be rendered virtually black having only 5-8 % reflectance over the whole visible spectrum of light. The reflectance of the steel sample drops to % using surface structures obtained by direct focusing of the femtosecond light. Note, that the reflectance is saturated to this value and it cannot be diminished by applying more pulses using above mentioned fluence. In case of the interferometric ablation using higher fluence values can reduce the reflectance only by few percents. However, with higher fluence this saturation level can be reached using smaller number of pulses. When using direct focusing the reflectance can be reduced near to the saturation level obtained using interferometric ablation, but value of several times higher average fluence must be applied compared to the interferometric ablation. Reflectance Wavelength (nm) Fig. 4. Measured reflectance spectra for polished steel (above), structured surface using direct focusing (middle) and structured surface using interferometric ablation (bottom). For copper the changes in absorptance using above mentioned fluence and pulse number are also clear, but less dramatic. The holes are shallower than for steel sample. This is probably due to the almost negligible initial absorption of 800 nm for copper. However, we see no technical constraint for rendering copper black by using higher number of pulses. The reflectance spectrum of the modified sample surface for copper is shown in the Fig. 5. The reason for this enhancement in absorptance due to the hole-structure is yet unclear. The diffraction theory for ideal hole structure does not support such enhancement of absorptance. Theoretically this kind of metal grating structures can be handled using Fourier modal method, also known as the rigorous coupled-wave approach [16, 17, 18]. Using fourier modal method (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13841
5 1 0.8 Reflectance Wavelength (nm) Fig. 5. Measured reflectance spectra for polished copper (above), structured surface using direct focusing (middle) and structured surface using interferometric ablation (bottom). we have calculated the absorption for such metal grating having cylindrical holes. Calculated results are shown in the Fig. 6 for different hole depths. Parameters used in the calculation are grating period of 2.1 μm and hole diameter of 1.9 μm. Although the grating starts to absorb when holes gets deeper, total absorption is not achieved like in measurements. We believe that the observed total absorption is due to the combined effects of multiple reflections in cylindrical cavities and nanoscale structuring acting as an effective refractive index medium. However, incorporation of such nanostructures to the theoretical model is not straightforward and cannot be presented here. Fig. 6. Theoretical reflectance of the steel surface with cylindrical holes. 3. Conclusion We have demonstrated the new efficient technique to enhance the absorptance of metals. Total absorption over whole visible region of the spectrum was obtained for stainless steel sample using only modest values of pulse number and fluence. This technique is based on interferometric ablation for structuring hole-array to the sample surface and is more efficient and controlled than just focusing the light to the surface, that have been previously used for absorptance enhancement [2, 3]. The technique may be further improved by optimizing the size of the holes. (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13842
6 Acknowledgments This work was supported by TEKES, Finnish Funding Agency for Technology and Innovation. The author acknowledge the Network of Excellence on Micro-Optics (NEMO). http// (C) 2007 OSA 17 October 2007 / Vol. 15, No. 21 / OPTICS EXPRESS 13843
Xuechang Ren a *, Canhui Wang, Yanshuang Li, Shaoxin Shen, Shou Liu
Available online at www.sciencedirect.com Physics Procedia 22 (2011) 493 497 2011 International Conference on Physics Science and Technology (ICPST 2011) Optical Tweezers Array System Based on 2D Photonic
More informationHOLOGRAPHIC FEMTOSECOND LASER PROCESSING AND THREE-DIMENSIONAL RECORDING IN BIOLOGICAL TISSUES
Progress In Electromagnetics Research Letters, Vol. 2, 115 123, 2008 HOLOGRAPHIC FEMTOSECOND LASER PROCESSING AND THREE-DIMENSIONAL RECORDING IN BIOLOGICAL TISSUES Y. Hayasaki Department of Optical Science
More informationWAVELENGTH MANAGEMENT
BEAM DIAGNOS TICS SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER SOLUTIONS POWER DETECTORS ENERGY DETECTORS MONITORS Camera Accessories WAVELENGTH MANAGEMENT UV CONVERTERS UV Converters
More informationSupplementary Figure 1: Schematic of the nanorod-scattered wave along the +z. direction.
Supplementary Figure 1: Schematic of the nanorod-scattered wave along the +z direction. Supplementary Figure 2: The nanorod functions as a half-wave plate. The fast axis of the waveplate is parallel to
More informationA Single Grating-lens Focusing Two Orthogonally Polarized Beams in Opposite Direction
, pp.41-45 http://dx.doi.org/10.14257/astl.2016.140.08 A Single Grating-lens Focusing Two Orthogonally Polarized Beams in Opposite Direction Seung Dae Lee 1 1* Dept. of Electronic Engineering, Namseoul
More informationIntroduction Introduction Introduction Introduction Introduction use damage for processing! Outline Outline Processing with fs pulses Role of focusing Low-energy processing Processing with fs pulses 10
More informationEfficient metal processing using high average power ultrafast laser
Efficient metal processing using high average power ultrafast laser Strasbourg, September 13 th, 2017 J. Lopez J. Lopez et al., Journal of Laser Micro and Nanofabrication, submitted (2017) G. Mincuzzi
More informationDiffraction Efficiency
Diffraction Efficiency Turan Erdogan Gratings are based on diffraction and interference: Diffraction gratings can be understood using the optical principles of diffraction and interference. When light
More informationCompany Pioneer in Ytterbium ultrafast lasers High quality manufacturing Intense and active R&D Located in Bordeaux and Paris US offices in Boston and
High power ultrafast lasers Eric Mottay High Brightness Laser sources Burgdorf, November 26, 2009 Company Pioneer in Ytterbium ultrafast lasers High quality manufacturing Intense and active R&D Located
More informationWhite-light interference microscopy: minimization of spurious diffraction effects by geometric phase-shifting
White-light interference microscopy: minimization of spurious diffraction effects by geometric phase-shifting Maitreyee Roy 1, *, Joanna Schmit 2 and Parameswaran Hariharan 1 1 School of Physics, University
More informationOptical diffraction gratings embedded in BK-7 glass by low-density plasma formation using femtosecond laser
Optical diffraction gratings embedded in BK-7 glass by low-density plasma formation using femtosecond laser Jung-Kyu PARK 1, Sung-Hak CHO 1, Kwang-Ho KIM 2, Myung-Chang KANG 2 1. Nano Machining Laboratory,
More informationAnalysis of Slanted Gratings for Lightguide Coupling
Analysis of Slanted Gratings for Lightguide Coupling Abstract Slanted gratings are commonly used for coupling light into optical lightguides due to their high efficiency in a certain diffraction order.
More informationDevelopment of a Simulation Method of Three-Dimensional Ultrafine Processing by Femtosecond Laser Shunsuke Nabetani 1, a, Hideki Aoyama 1, b * 1, 2, c
Development of a Simulation Method of Three-Dimensional Ultrafine Processing by Femtosecond Laser Shunsuke Nabetani 1, a, Hideki Aoyama 1, b * 1,, c, Masahiro Ueda Yoshinori Ogawa 1,, d 1,, 3, e, and Kazuo
More informationNear Field Observation of a Refractive Index Grating and a Topographical Grating by an Optically Trapped Gold Particle
Near Field Observation of a Refractive Index Grating and a Topographical Grating by an Optically Trapped Gold Particle Hiroo UKITA and Hirotaka UEMI Ritsumeikan University, Kusatsu-shi, Shiga, 2 Japan
More informationApplications of adaptive optics in femtosecond laser material processing
Applications of adaptive optics in femtosecond laser material processing STFC / Photonics KTN - Laser Applications of Adaptive Optics Professor Derryck T. Reid Ultrafast Optics Group School of Engineering
More informationspecular diffuse reflection.
Lesson 8 Light and Optics The Nature of Light Properties of Light: Reflection Refraction Interference Diffraction Polarization Dispersion and Prisms Total Internal Reflection Huygens s Principle The Nature
More informationWAVELENGTH MANAGEMENT
Camera Accessories WAVELENGTH MANAGEMENT UV CONVERTERS UV Converters take advantage of a phenomenon called fluorescence to extend the performance range of the Beamage beam profiling camera to ultraviolet
More informationThree-dimensional imaging of 30-nm nanospheres using immersion interferometric lithography
Three-dimensional imaging of 30-nm nanospheres using immersion interferometric lithography Jianming Zhou *, Yongfa Fan, Bruce W. Smith Microelectronics Engineering Department, Rochester Institute of Technology,
More informationDiffraction. Single-slit diffraction. Diffraction by a circular aperture. Chapter 38. In the forward direction, the intensity is maximal.
Diffraction Chapter 38 Huygens construction may be used to find the wave observed on the downstream side of an aperture of any shape. Diffraction The interference pattern encodes the shape as a Fourier
More informationMicroscopy. Marc McGuigan North Quincy High School Thursday, May 11, 2006
Microscopy Marc McGuigan North Quincy High School Thursday, May 11, 006 Outline Activity Introduction Electromagnetic Spectrum Visible Light Light Microscope AFM Scanning Electron Microscopy Near-Field
More informationOptimization of modified volume Fresnel zone plates
Birck Nanotechnology Center Birck and NCN Publications Purdue Libraries Year 2009 Optimization of modified volume Fresnel zone plates Pornsak Srisungsitthisunti Okan Ersoy Xianfan Xu Purdue University,
More informationSTEEL SURFACE CHARACTERIZATION USING 3D PROFILOMETRY
STEEL SURFACE CHARACTERIZATION USING 3D PROFILOMETRY Prepared by Andrea Novitsky 6 Morgan, Ste156, Irvine CA 92618 P: 949.461.9292 F: 949.461.9232 nanovea.com Today's standard for tomorrow's materials.
More informationLIGHT. Speed of light Law of Reflection Refraction Snell s Law Mirrors Lenses
LIGHT Speed of light Law of Reflection Refraction Snell s Law Mirrors Lenses Light = Electromagnetic Wave Requires No Medium to Travel Oscillating Electric and Magnetic Field Travel at the speed of light
More informationPhysics Midterm I
Phys121 - February 6, 2009 1 Physics 121 - Midterm I Last Name First Name Student Number Signature Tutorial T.A. (circle one): Ricky Chu Firuz Demir Maysam Emadi Alireza Jojjati Answer ALL 10 questions.
More informationText for the class, Pump-Probe Technique for Picosecond Time-resolved X-ray Diffraction at Cheiron School
BL19LXU Yoshihito Tanaka, Oct. 2013 Text for the class, Pump-Probe Technique for Picosecond Time-resolved X-ray Diffraction at Cheiron School Abstract The pulsed time structure of synchrotron radiation
More informationCoupling of surface roughness to the performance of computer-generated holograms
Coupling of surface roughness to the performance of computer-generated holograms Ping Zhou* and Jim Burge College of Optical Sciences, University of Arizona, Tucson, Arizona 85721, USA *Corresponding author:
More informationSilicon Avalanche Photodiodes in Dynamic Light Scattering
Silicon Avalanche Photodiodes in Dynamic Light Scattering August 2016 Introduction This application note describes the use of the ID100 single photon counting detector for the measurement of light scattered
More informationPhysics 625 Femtosecond laser Project
Physics 625 Femtosecond laser Project The purpose of this project is for each person to gain experience in designing part of a femtosecond laser system for pump-probe experiments. The system diagram is
More informationMICROMACHINING OF OPTICAL FIBRES WITH A NANOSECOND LASER FOR OPTICAL COMMUNICATION AND SENSOR APPLICATIONS
58 SOUTH AFRICAN INSTITUTE OF ELECTRICAL ENGINEERS Vol.102(3) September 2011 MICROMACHINING OF OPTICAL FIBRES WITH A NANOSECOND LASER FOR OPTICAL COMMUNICATION AND SENSOR APPLICATIONS D. Schmieder, R.
More informationUNIT 102-9: INTERFERENCE AND DIFFRACTION
Name St.No. - Date(YY/MM/DD) / / Section Group # UNIT 102-9: INTERFERENCE AND DIFFRACTION Patterns created by interference of light in a thin film. OBJECTIVES 1. Understand the creation of double-slit
More informationPhy 133 Section 1: f. Geometric Optics: Assume the rays follow straight lines. (No diffraction). v 1 λ 1. = v 2. λ 2. = c λ 2. c λ 1.
Phy 133 Section 1: f Geometric Optics: Assume the rays follow straight lines. (No diffraction). Law of Reflection: θ 1 = θ 1 ' (angle of incidence = angle of reflection) Refraction = bending of a wave
More informationRecent Advances in Ultrafast Laser Subtractive and Additive Manufacturing
Industrial Affiliates Symposium March 16-18, 2017 Recent Advances in Ultrafast Laser Subtractive and Additive Manufacturing Xiaoming Yu Assistant Professor Ultrafast Laser Processing Group CREOL, The College
More informationPROCEEDINGS OF SPIE. Simulation of lateral color for a hybrid refractive-diffractive eyepiece by field tracing methods
PROCEEDINGS OF SPIE SPIEDigitalLibrary.org/conference-proceedings-of-spie Simulation of lateral color for a hybrid refractive-diffractive eyepiece by field tracing methods D. Batte, M. Kuhn, F. Wyrowski
More informationIntroduction to Diffraction Gratings
Introduction to Diffraction Diffraction (Ruled and Holographic) Diffraction gratings can be divided into two basic categories: holographic and ruled. A ruled grating is produced by physically forming grooves
More information2011 Optical Science & Engineering PhD Qualifying Examination Optical Sciences Track: Advanced Optics Time allowed: 90 minutes
2011 Optical Science & Engineering PhD Qualifying Examination Optical Sciences Track: Advanced Optics Time allowed: 90 minutes Answer all four questions. All questions count equally. 3(a) A linearly polarized
More informationPHY 171 Lecture 6 (January 18, 2012)
PHY 171 Lecture 6 (January 18, 2012) Light Throughout most of the next 2 weeks, we will be concerned with the wave properties of light, and phenomena based on them (interference & diffraction). Light also
More informationSUPPLEMENTARY INFORMATION. Plasmonic black gold by adiabatic nanofocusing and absorption of. light in ultra-sharp convex grooves
SUPPLEMENTARY INFORMATION Plasmonic black gold by adiabatic nanofocusing and absorption of light in ultra-sharp convex grooves Thomas Søndergaard 1, Sergey M. Novikov 2, Tobias Holmgaard 1, René L. Eriksen
More informationWide-angle and high-efficiency achromatic metasurfaces for visible light
Wide-angle and high-efficiency achromatic metasurfaces for visible light Zi-Lan Deng, 1 Shuang Zhang, 2 and Guo Ping Wang 1,* 1 College of Electronic Science and Technology and Key Laboratory of Optoelectronic
More informationLab2: Single Photon Interference
Lab2: Single Photon Interference Xiaoshu Chen* Department of Mechanical Engineering, University of Rochester, NY, 14623 ABSTRACT The wave-particle duality of light was verified by multi and single photon
More informationSURFACE BOUNDARY MEASUREMENT USING 3D PROFILOMETRY
SURFACE BOUNDARY MEASUREMENT USING 3D PROFILOMETRY Prepared by Craig Leising 6 Morgan, Ste156, Irvine CA 92618 P: 949.461.9292 F: 949.461.9232 nanovea.com Today's standard for tomorrow's materials. 2013
More informationFEMTO OpTicsTM in us! O j rld wo T as F ra T ul in an E liv
FEMTO optics TM We live in an ultrafast world TM join us! 2011 1 FEMTO optics TM 2011 1 A new brand is born We at FEMTOLASERS believe in taking great care of our customers through long-term relationships
More informationRay Optics I. Last time, finished EM theory Looked at complex boundary problems TIR: Snell s law complex Metal mirrors: index complex
Phys 531 Lecture 8 20 September 2005 Ray Optics I Last time, finished EM theory Looked at complex boundary problems TIR: Snell s law complex Metal mirrors: index complex Today shift gears, start applying
More informationChapter 38. Diffraction Patterns and Polarization
Chapter 38 Diffraction Patterns and Polarization Diffraction Light of wavelength comparable to or larger than the width of a slit spreads out in all forward directions upon passing through the slit This
More informationTutorial: Instantaneous Measurement of M 2 Beam Propagation Ratio in Real-Time
Tutorial: Instantaneous Measurement of M 2 Beam Propagation Ratio in Real-Time By Allen M. Cary, Jeffrey L. Guttman, Razvan Chirita, Derrick W. Peterman, Photon Inc A new instrument design allows the M
More informationLaser readiness for all optical EUV FEL
Laser readiness for all optical EUV FEL Akira Endo EUVA (Extreme Ultraviolet Lithography System Development Association) EUVL Source Workshop 19 October, 2006 Barcelona, Spain Acknowledgments This work
More informationHigh spatial resolution measurement of volume holographic gratings
High spatial resolution measurement of volume holographic gratings Gregory J. Steckman, Frank Havermeyer Ondax, Inc., 8 E. Duarte Rd., Monrovia, CA, USA 9116 ABSTRACT The conventional approach for measuring
More informationPassive intra-cavity phase locking of laser channels
Optics Communications 63 (006) 60 64 www.elsevier.com/locate/optcom Passive intra-cavity phase locking of laser channels iran Shimshi *, Amiel A. Ishaaya, Vardit Ekhouse, Nir Davidson, Asher A. Friesem
More informationSecondary grating formation by readout at Bragg-null incidence
Secondary grating formation by readout at Bragg-null incidence Ali Adibi, Jose Mumbru, Kelvin Wagner, and Demetri Psaltis We show that when a dynamic hologram is read out by illumination at the Bragg nulls
More informationWhat is it? How does it work? How do we use it?
What is it? How does it work? How do we use it? Dual Nature http://www.youtube.com/watch?v=dfpeprq7ogc o Electromagnetic Waves display wave behavior o Created by oscillating electric and magnetic fields
More informationOptical properties and characterization
Optical properties and characterization Name Picture Description Site Responsible 1 Laser Nd:YAG MAPLE (Matrix Assisted Pulsed Laser Evaporation) system for biomaterials and polymeric thin film deposition
More informationPhysics 123 Optics Review
Physics 123 Optics Review I. Definitions & Facts concave converging convex diverging real image virtual image real object virtual object upright inverted dispersion nearsighted, farsighted near point,
More informationTotal internal reflection diffraction grating in conical mounting
Optics Communications 261 (2006) 13 18 www.elsevier.com/locate/optcom Total internal reflection diffraction grating in conical mounting L. Eisen *, M.A. Golub, A.A. Friesem Department of Physics of Complex
More informationSystematic design process for slanted graing couplers,
Brigham Young University BYU ScholarsArchive All Faculty Publications 2006-08-20 Systematic design process for slanted graing couplers, Gregory P. Nordin nordin@byu.edu J. Jiang See next page for additional
More information1. Polarization effects in optical spectra of photonic crystals
Speech for JASS 05. April 2005. Samusev A. 1. Polarization effects in optical spectra of photonic crystals Good afternoon. I would like to introduce myself. My name is Anton Samusev. I m a student of Saint
More informationTHz Transmission Properties of Metallic Slit Array
THz Transmission Properties of Metallic Slit Array Guozhong Zhao * Department of Physics, Capital Normal University, Beijing 100048, China Beijing Key Lab for Terahertz Spectroscopy and Imaging Key Lab
More informationS-WAVEPLATE RADIAL/AZIMUTH POLARIZATION CONVERTER
S-WAVEPLATE RADIAL/AZIMUTH POLARIZATION CONVERTER Operation manual Konstitucijos ave. 23 LT-08105 Vilnius, Lithuania Konstitucijos ave. 23C LT-08105 Vilnius, Lithuania tel. +370 5 272 57 38 fax +370 5
More informationFringe modulation skewing effect in white-light vertical scanning interferometry
Fringe modulation skewing effect in white-light vertical scanning interferometry Akiko Harasaki and James C. Wyant An interference fringe modulation skewing effect in white-light vertical scanning interferometry
More informationChapter 2: Wave Optics
Chapter : Wave Optics P-1. We can write a plane wave with the z axis taken in the direction of the wave vector k as u(,) r t Acos tkzarg( A) As c /, T 1/ and k / we can rewrite the plane wave as t z u(,)
More informationDesign of two-dimensional polarization-selective diffractive optical elements with form-birefringent microstructures
Design of two-dimensional polarization-selective diffractive optical elements with form-birefringent microstructures Mark S. Mirotznik, David M. Pustai, Dennis W. Prather, and Joseph N. Mait We describe
More informationdq dt I = Irradiance or Light Intensity is Flux Φ per area A (W/m 2 ) Φ =
Radiometry (From Intro to Optics, Pedrotti -4) Radiometry is measurement of Emag radiation (light) Consider a small spherical source Total energy radiating from the body over some time is Q total Radiant
More informationThe diffraction pattern from a hexagonally-shaped hole. Note the six-fold symmetry of the pattern. Observation of such complex patterns can reveal
The diffraction pattern from a hexagonally-shaped hole. Note the six-fold symmetry of the pattern. Observation of such complex patterns can reveal the underlying symmetry structure of the object that diffracts
More informationdq dt I = Irradiance or Light Intensity is Flux Φ per area A (W/m 2 ) Φ =
Radiometry (From Intro to Optics, Pedrotti -4) Radiometry is measurement of Emag radiation (light) Consider a small spherical source Total energy radiating from the body over some time is Q total Radiant
More informationReduced surface roughness of solid thin films prepared by alternating-bias, radio-frequency magnetron sputtering
2174 J. Opt. Soc. Am. B/ Vol. 20, No. 10/ October 2003 R. Rabady and I. Avrutsky Reduced surface roughness of solid thin films prepared by alternating-bias, radio-frequency magnetron sputtering Rabi Rabady
More informationChapter 24. Wave Optics. Wave Optics. The wave nature of light is needed to explain various phenomena
Chapter 24 Wave Optics Wave Optics The wave nature of light is needed to explain various phenomena Interference Diffraction Polarization The particle nature of light was the basis for ray (geometric) optics
More informationDiffraction Diffraction occurs when light waves is passed by an aperture/edge Huygen's Principal: each point on wavefront acts as source of another
Diffraction Diffraction occurs when light waves is passed by an aperture/edge Huygen's Principal: each point on wavefront acts as source of another circular wave Consider light from point source at infinity
More informationAnalysis of micro-fresnel lenses with local grating theory and its comparison with fully electromagnetic methods
1938 J. Opt. Soc. Am. A/ Vol. 26, No. 9/ September 2009 Ichikawa et al. Analysis of micro-fresnel lenses with local grating theory and its comparison with fully electromagnetic methods Hiroyuki Ichikawa,
More information12/7/2012. Biomolecular structure. Diffraction, X-ray crystallography, light- and electron microscopy. CD spectroscopy, mass spectrometry
phase difference at a given distance constructive/destructive interference Biomolecular structure. Diffraction, X-ray crystallography, light- and electron microscopy. CD spectroscopy, mass spectrometry
More informationSURFACE TEXTURE EFFECT ON LUSTER OF ANODIZED ALUMINUM USING 3D PROFILOMETRY
SURFACE TEXTURE EFFECT ON LUSTER OF ANODIZED ALUMINUM USING 3D PROFILOMETRY Prepared by Duanjie Li, PhD 6 Morgan, Ste156, Irvine CA 92618 P: 949.461.9292 F: 949.461.9232 nanovea.com Today's standard for
More informationRadiometry (From Intro to Optics, Pedrotti 1-4) Radiometry is measurement of Emag radiation (light) Consider a small spherical source Assume a black
Radiometry (From Intro to Optics, Pedrotti -4) Radiometry is measurement of Emag radiation (light) Consider a small spherical source Assume a black body type emitter: uniform emission Total energy radiating
More informationShading of a computer-generated hologram by zone plate modulation
Shading of a computer-generated hologram by zone plate modulation Takayuki Kurihara * and Yasuhiro Takaki Institute of Engineering, Tokyo University of Agriculture and Technology, 2-24-16 Naka-cho, Koganei,Tokyo
More informationUnderstanding and selecting diffraction gratings
Understanding and selecting diffraction gratings Diffraction gratings are used in a variety of applications where light needs to be spectrally split, including engineering, communications, chemistry, physics
More informationDiffraction Gratings as Anti Reflective Coatings Noah Gilbert. University of Arizona ngilbert .arizona.edu Phone: (520)
Diffraction Gratings as Anti Reflective Coatings Noah Gilbert University of Arizona Email: ngilbertemail.arizona.edu Phone: (520)304 4864 Abstract: Diffraction gratings with sub wavelength spatial frequencies
More informationMetallic Transmission Screen for Sub-wavelength Focusing
Metallic Transmission Screen for Sub-wavelength Focusing A.M.H. Wong, C.D. Sarris and G.V. leftheriades Abstract: A simple metallic transmission screen is proposed that is capable of focusing an incident
More informationLecture 4 Recap of PHYS110-1 lecture Physical Optics - 4 lectures EM spectrum and colour Light sources Interference and diffraction Polarization
Lecture 4 Recap of PHYS110-1 lecture Physical Optics - 4 lectures EM spectrum and colour Light sources Interference and diffraction Polarization Lens Aberrations - 3 lectures Spherical aberrations Coma,
More informationPhysical & Electromagnetic Optics: Diffraction Gratings
31/05/2018 Physical & Electromagnetic Optics: Diffraction Gratings Optical Engineering Prof. Elias N. Glytsis School of Electrical & Computer Engineering National Technical University of Athens Multiple
More informationNull test for a highly paraboloidal mirror
Null test for a highly paraboloidal mirror Taehee Kim, James H. Burge, Yunwoo Lee, and Sungsik Kim A circular null computer-generated hologram CGH was used to test a highly paraboloidal mirror diameter,
More informationThe location of the bright fringes can be found using the following equation.
What You Need to Know: In the past two labs we ve been thinking of light as a particle that reflects off of a surface or refracts into a medium. Now we are going to talk about light as a wave. If you take
More informationLASer Cavity Analysis and Design
The unique combination of simulation tools for LASer Cavity Analysis and Design During the last 15 years LASCAD has become industry-leading so ware for LASer Cavity Analysis and Design. The feedback from
More informationMeasurement of period difference in grating pair based on analysis of grating phase shift
Measurement of period difference in grating pair based on analysis of grating phase shift Chao Guo, Lijiang Zeng State Key Laboratory of Precision Measurement Technology and Instruments Department of Precision
More informationChapter 24 - The Wave Nature of Light
Chapter 24 - The Wave Nature of Light Summary Four Consequences of the Wave nature of Light: Diffraction Dispersion Interference Polarization Huygens principle: every point on a wavefront is a source of
More informationCoherent Gradient Sensing Microscopy: Microinterferometric Technique. for Quantitative Cell Detection
Coherent Gradient Sensing Microscopy: Microinterferometric Technique for Quantitative Cell Detection Proceedings of the SEM Annual Conference June 7-10, 010 Indianapolis, Indiana USA 010 Society for Experimental
More informationFormulas of possible interest
Name: PHYS 3410/6750: Modern Optics Final Exam Thursday 15 December 2011 Prof. Bolton No books, calculators, notes, etc. Formulas of possible interest I = ɛ 0 c E 2 T = 1 2 ɛ 0cE 2 0 E γ = hν γ n = c/v
More informationChapter 24. Wave Optics. Wave Optics. The wave nature of light is needed to explain various phenomena
Chapter 24 Wave Optics Wave Optics The wave nature of light is needed to explain various phenomena Interference Diffraction Polarization The particle nature of light was the basis for ray (geometric) optics
More informationExperimental reconstruction of a highly reflecting fiber Bragg grating by using spectral regularization and inverse scattering
3284 J. Opt. Soc. Am. A/ Vol. 24, No. 10/ October 2007 Rosenthal et al. Experimental reconstruction of a highly reflecting fiber Bragg grating by using spectral regularization and inverse scattering Amir
More informationExperiment 8 Wave Optics
Physics 263 Experiment 8 Wave Optics In this laboratory, we will perform two experiments on wave optics. 1 Double Slit Interference In two-slit interference, light falls on an opaque screen with two closely
More informationComputer-originated planar holographic optical elements
Computer-originated planar holographic optical elements Silviu Reinhorn, Yaakov Amitai, and Albert A. Friesem We present novel, to our knowledge, methods for the analytical design and recording of planar
More informationFeasibility of Laser Induced Plasma Micro-machining (LIP-MM)
Feasibility of Laser Induced Plasma Micro-machining (LIP-MM) Kumar Pallav 1, Kornel F. Ehmann 1 Department of Mechanical Engineering Northwestern University Evanston, IL 60208, USA {kumarpallav2008@u.northwestern.edu,
More informationWhat is light? This question sparked a huge debate in physics.
Optics Sol PH. 11 What is light? This question sparked a huge debate in physics. Light is a Stream of Particles. Newton called corpuscles Colors travel at different speeds. Einstein called quanti Light
More informationDevelopment of automated ultraviolet laser beam profiling system using fluorometric technique
Development of automated ultraviolet laser beam profiling system using fluorometric technique BB Shrivastava*, NS Benerji, P Bhatnagar, HS Vora a and U Nundy Chemical and Excimer Laser Section a Laser
More informationTheory and Measuring of Antireflection Coatings
Theory and Measuring of Antireflection Coatings Steffen Lorch The characterization of antireflection (AR) coatings is not trivial. A preferred measurement method is the Hakki-Paoli method. But for broad-area
More informationStevens High School AP Physics II Work for Not-school
1. Gravitational waves are ripples in the fabric of space-time (more on this in the next unit) that travel at the speed of light (c = 3.00 x 10 8 m/s). In 2016, the LIGO (Laser Interferometry Gravitational
More informationChapter 36. Image Formation
Chapter 36 Image Formation Apr 22, 2012 Light from distant things We learn about a distant thing from the light it generates or redirects. The lenses in our eyes create images of objects our brains can
More informationAnalysis of the Gaussian Beam on a Corrugated Dielectric Interface
(An ISO 3297: 27 Certified Organization) Vol. 3, Issue 9, September 214 Analysis of the Gaussian Beam on a Corrugated Dielectric Interface Mohamed B. El_Mashade 1, Adel Shaaban 2 Department of Electrical
More informationLight and Electromagnetic Waves. Honors Physics
Light and Electromagnetic Waves Honors Physics Electromagnetic Waves EM waves are a result of accelerated charges and disturbances in electric and magnetic fields (Radio wave example here) As electrons
More informationDiffraction Diffraction occurs when light waves pass through an aperture Huygen's Principal: each point on wavefront acts as source of another wave
Diffraction Diffraction occurs when light waves pass through an aperture Huygen's Principal: each point on wavefront acts as source of another wave If light coming from infinity point source at infinity
More informationratio of the volume under the 2D MTF of a lens to the volume under the 2D MTF of a diffraction limited
SUPPLEMENTARY FIGURES.9 Strehl ratio (a.u.).5 Singlet Doublet 2 Incident angle (degree) 3 Supplementary Figure. Strehl ratio of the singlet and doublet metasurface lenses. Strehl ratio is the ratio of
More informationThe Future of OCT? Swept Source. Todd J. Purkiss, MD, PhD River City Retina Club July 16, 2015
The Future of OCT? Swept Source Todd J. Purkiss, MD, PhD River City Retina Club July 16, 2015 Background on OCT Optical Coherence Tomography Optical When a light wave meets the interface of two differing
More informationMODULE 3. FACTORS AFFECTING 3D LASER SCANNING
MODULE 3. FACTORS AFFECTING 3D LASER SCANNING Learning Outcomes: This module discusses factors affecting 3D laser scanner performance. Students should be able to explain the impact of various factors on
More informationLasers and Femtosecond Lasers
1/26/2004 Lasers and Femtosecond Lasers As you learned in the lecture, a Ti:sapphire laser can operate either as a tunable, continuous-wave (CW) laser, or a pulsed, self-modelocked, laser. A slight alignment
More informationSurface Plasmon and Nano-metallic layout simulation with OptiFDTD
Surface Plasmon and Nano-metallic layout simulation with OptiFDTD 1. Lorentz_Drude Model and Surface Plasma wave Metallic photonic materials demonstrate unique properties due to the existence on metals
More information