Cameras 4 in 1. User Manual TBK-MD5641EIR TBK-MD5841EIR/ TBK-BUL4841EIR

Size: px

Start display at page:

Download "Cameras 4 in 1. User Manual TBK-MD5641EIR TBK-MD5841EIR/ TBK-BUL4841EIR"

Emerald Gallagher
6 years ago
Views:

1 Cameras 4 in 1 User Manual TBK-MD5641EIR TBK-MD5841EIR/ TBK-BUL4841EIR

2 Contents 1 Notes Product Introduction Production Instruction Product Feature Product Structure Technical Parameters Product Installation Note Installation Tools and Information Installation Method Connection Menu Instruction Camera Menu Setting Appendix: FAQ

3 1 Notes Read this manual carefully before use. 1)To reduce the risk of electric shock, do not open the machine and maintain by yourself, please consult a professional service person. 2)To prevent fire or shock hazard, use the power after safety certification, the input voltage, current, voltage polarity and operating temperature must meet the requirements of this camera. 3)Please note the operating temperature and environmental requirements of the camera, avoid too low or too high temperature. General operating temperature range of -10 ~+50 (Fahrenheit temperature is 14 ~122 ). Avoid flooding and rain, minimize dust and moisture erosion, otherwise camera would be damaged. 4)Cameras in use should avoid direct sunlight, glare, otherwise the sensor will be damaged. 5)Do not touch the sensor surface, if any foreign objects exits, a cotton swab or lens paper can be used to wipe, if it is difficult to remove, a neutral detergent diluted with water would be useful. Do not use corrosive solution. 6)In order to make the camera work smoothly and obtain a satisfactory image, the power cord and video connection can not be 2

4 too long, otherwise the increase of line loss will lead to the inadequate magnitude of the operating voltage of the camera or video signal Inadequate. 7)In order to prevent the camera from falling, please do not place the camera on an unstable bracket, base or other unstable objects. Otherwise it will lead to injury, at the same time, the camera will be damaged. 8)The camera cannot be placed near the radiator or heating resistor. 2 Product Introduction 2.1 Production Instruction This manual is applicable to following models: 1080p resolution camera: TBK-MD5641EIR, TBK-MD5841EIR, TBK-BUL4841EIR. This series of cameras are adopted CMOS image sensor with high performance, which provides mega pixel resolution and supports HD video. Moreover, it supports monitoring signals coaxial transmission. Transmission distance can reach more than 300M based on 75-3 coaxial cable. The series can support both TVI/CVBS 960H output as well as realize high speed, long distance and real time video transmission. 3

5 2.2 Product Feature Coaxial cable adopted,bnc connector as cable standard. Dual output: HD signal switcheable to TVI/CV/AHD and CVBS signal. Auto Day/Night(ICR) Auto Defog WDR, 2D/3D NR Motion Detection, Privacy Mask Auto Iris(Specific models) Back-end support optical zoom (motorized zoom lens models) Voltage Input: DC 12V 3 Product Structure The followings are the dimensions of some products. No further notice for the upgraded version. Photo 3-1 TBK-BUL4841EIR 4

6 Photo 3-2 TBK-MD5841EIR Photo 3-3 TBK-MD5641EIR 5

7 4 Technical Parameters Model TBK-MD5641EIR TBK-MD5841EIR Image Sensor Image Effective Pixels Resolution S/N Ratio Min. Illumination Scanning System Video Output Function Day & Night White Balance Defog DNR ACE Privacy Mask Motion Detection 1 / MP SONY Exmor CMOS 1928(H) 1088(V) Digital:1920x1080p 25ips Analog:700LTV 41dB (AGC Off) Color: 0.1Lux@F2.0 AGCE ON B / N:0.001Lux@F2.0 AGC ON (0Lux IR On) Progressive Digital: 1080p HD-TVI or HD-CVI or AHD Analog:1Vp-p75Ω/BNC EXTERN,COLOR, B&W, AUTO Auto OFF/ON 2D+3D NR OFF/LOW/MIDDLE/HIGH ON/OFF (16 Areas) ON/OFF (4 Areas) 6

8 Lens 3.6mm mm Auto Focus IR LED IR Range 3pcs IR Array LEDS 40m General specification Input Voltage DC12V±10% Current 300mA 410mA Power Consumption <4.5W <6W Weight 240g 630g IP Rating IP66 Operation Temp. -10 ~+50 (14 ~122 ) Operation humidity <85%RH (Non-condensation) Model Image Sensor Image Effective Pixels Resolution S/N Ratio Min. Illumination Scanning System Video Output Function TBK-BUL4841EIR 1 / MP SONY Exmor CMOS 1928(H) 1088(V) Digital:1920x1080p 25ips Analog:700TLV 41dB (AGC Off) Color:0.1Lux@F2.0 AGC ON B / N:0.001Lux@F2.0 AGC ON (0Lux IR On) Progressive Digital: 1080P HD-TVI or HD-CVI or AHD Analógica:1Vp-p75Ω/BNC 7

9 Day & Night White Balance Defog DNR ACE Privacy Mask Motion Detection ZOOM IN Lens IR LED IR Range EXTERN,COLOR, B&W, AUTO Auto OFF/ON 2D+3D NR OFF/LOW/MIDDLE/HIGH ON/OFF (16 Areas) ON/OFF (4 Areas) 1X-8X mm Auto Focus 24pcs IR LEDS 35m General specification Input Voltage DC12V±10% Current 370mA ±10% Power Consumption <4.5W Weight 630g IP Rating IP66 Operation Temp. -10 ~+60 (14 ~122 ) Operation humidity <90%RH (Non-condensation) 8

10 5 Product Installation 5.1 Note 1) Make sure the unit is powered off before installation. 2) Check power supply voltage consistent with the electric voltage to prevent voltage unworthy, resulting in damage to the device. 3) Do not use in the environment beyond the boundaries of the temperature, and maintain good ventilation to prevent the rain in order to reduce the risk of fire or electric shock. 4) The installation and maintenance of this product should be professional, please do not in any way to remove or modify the equipment; can only use the required accessories of manufacturers. Problems caused by unauthorized repair are at your own risk. 5.2 Installation Tools and Information Prepare the required engineering data and instructions. Before installation please prepare the following tools and instrumentation: A straight or a Phillips-head screwdriver, multi-meter, scissors, needle nose pliers, tape measure, pencil and so on. 9

11 5.3 Installation Method 1. Check the equipment whether it is damaged. 2. Mounting bracket or base. 1If the cement wall, install the expansion screws (expansion screw holes need stand or base hole), and then mount bracket or base. 2If the wooden wall, use self-tapping screws to mount. 3. Mounting the camera a. Dome Camera Adjust the lens position and make it aim at the monitoring points and present a clear picture, manually fix lens location and adjust the hemisphere cover. Re-examine the screen whether the character meets the requirement. Tighten the hemisphere cover. b. Box Camera Adjust the body so that the lens aims at the monitoring points and presents a clear picture. Tighten the screws, to ensure that it does not move. Installation method above is for reference only, the specific installation, please be kind. Note: The wall needs to bear at least 3X weight of bracket (base) and camera. 10

12 5.4 Connection Connection as show in the figure below Camera connectors BNC Green connector: switchable TVI/CVI/AHD HD video signal. BNC Yellow connector: PAL Analogue video signal RCA Red connector: power supply 12 DCV 11

13 5.4.2 How to select HD video output Analogue video signal and HD video signal are simultaneous. HD signal (green connector) is switchable between three HD technologies: TVI or CVI or AHD. In order to select each HD signal please use the joystick attached at the camera wire and follow this two steps: Image: Camera wire attached joystick Firstly:, hold the central botton (menu botton) during 5 sec. Secondly: Move the joystick to the left for selecting TVI. Move the joystick to the right for selecting AHD. Move the joystick up (UP) for selecting CVI. NOTES: *Each time an HD technology is selected the type of HD signal is displayed on the monitor for a few seconds:tvi-pal or CVI-PAL or AHD-PAL. ** If we do not know which technology we have selected we can use the analogue video output (yellow connector), checking the menu first line: 12

14 Menu with TVI signal selection: Menu with CVI signal selection: Menu with AHD signal selection: 13

15 6 Menu Instruction To enter menu from analogue video output use joystick atacched on the camera wire.press "MENU" button to enter the main MENU, press "UP" and "DOWN" arows in order to select menus, press "LEFT" and "RIGHT" choice or set the corresponding function, to enter submenu please press "MENU" again. If you want to reset, please and press RESET menu option. To enter menu from HD video output use camera wire attached joystick or PTZ control menu from a TVI DVR. Guidance image for PTZ Control menu from a TVI DVR, use Iris+ as Enter. 14

EXPOSURE BRIGHTNESS- range 0~20, by default 10 SHUTTER- Options AUTO /MANUAL/FLICKER), options in MANUAL mode are: 1/25, 1/50,

16 6.1 Camera Menu Setting MAIN MENU LENS, select between iris control (ELC, ALC) ELC, electronic iris control. (NORMAL, DEBLUR) ALC, automatic iris control. INDOOR / OUTDOOR /DEBLUR *DEBLUR improve blur pictures caused by quick mouvements. EXPOSURE BRIGHTNESS- range 0~20, by default 10 SHUTTER- Options AUTO /MANUAL/FLICKER), options in MANUAL mode are: 1/25, 1/50, 1/100, 1/240,1/500, 1/1000, 1/2000, 1/4000,1/8000, 1/16000,1/30000/1/60000 SENS-UP - OFF, x2, x4, x8, x16, x32 AGC, automatic gain control, range 0~20 15

17 WHITE BAL, alows to adjust white balance. Options: AUTO, AUTO Ext, PRESET, MANUAL. MANUAL (KELVIN, R-GAIN, B-GAIN) KELVIN set color temperature (MIDDLE,HIGH, LOW) R-GAIN to set red color gain. Range 0~20 R-BLUE to set blue color gain. Range 0~20 BACKLIGHT, options OFF, BLC, HLC, WDR. HLC, detects strong light spots such as car headlights and flashlights in the dark (ALL DAY, NIGHT ONLY, LEVEL). LEVEL, range 0~20. BLC, allows to set one central area to avoit back light compensation. Available settings: H-POS: 0~20 V-POS: 0~20 H-SIZE: 0~20 V-SIZE: 0~20 By default it is an square area at the middle of the screen. WDR: Range LOW, MIDDLE, HIGH. DNR, to set digital noise level DNR 2D+3D. Options: (OFF, LOW, MIDDLE, HIGH). 16

(OFF, H-INV, V-INV, HV-INV). ACE, contrast adaptative settings.

18 DAY&NIGHT Menú MODE: select between working mode (AUTO, COLOR, B&W, EXTERN) IMAGE SHARPNESS, range 0~10 FREEZE, allows freezing image (OFF/ON) FLIP, allows the image to turn up and to turn downn (OFF, H-INV, V-INV, HV-INV). ACE, contrast adaptative settings. (LOW, MIDLE, HIGH, OFF) GAMMA, range (0.45, 0.5, 0.55, 0.6, 0.65) DEFOG, option anti fog (OFF, ON) ON: allows to set level (MIDDLE, HIGH, LOW) 17

CVBS, analogue video output estándar (PAL/NTSC). By default PAL.

19 SPECIAL SPECIAL-SYSTEM OUTPUT MODE, shows unit resolution:1080p. FRAME RATE, shows 25FPS( for PAL system) or 30FPS (for NTSC system). CVBS, analogue video output estándar (PAL/NTSC). By default PAL. BLACK LEVEL, black color level. (FULL, COMP, USER) VERSION, shows camera firmware version. 18

20 SPECIAL-PRIVACY menu for setting privacy masks, 16 areas avalilabe ZONE NUM, select the mask to set (0~15) ZONE DISP, activate /desactivate the mask (ON/OFF) H-POS, V-POS, to set mask posistion on screen H-SIZE, V-SIZE, to set size mask. Y-LEVEL, CR-LEVEL, CB-LEVEL, to set mask color. SPECIAL-MOTION 19

21 SENSITIVITY, to set motion detection sensitivity. (Range 0~20) WINDOW TONE, stand out detection area with background. WINDOW USE, to select one area between 4 available. (Range 0~3) WINDOW ZONE, to choose if are is visble or not. (OFF/ON). DET V-POS, DET V-POS, to set area position on screen. DET-H SIZE, DET V-SIZE, to set area horizontal and vertical size. ALARM, when there is a motion a message prompt MOVING! appears. Settings (ON/OFF) SPECIAL-SHADING SPECIAL-COLOR BAR COLORBAR, allows to show color bar (OFF/ON). SPECIAL-LENS ADJUST No use 20

22 Appendix: FAQ Q: No picture with power on A1: It may result for a wrong HD video signal selection, DVR and camera must have the same HD video technology. Different HD video technologies are incompatible between them. Go to How to select HD video output in order to select the right HD technology. A2: It may result from abnormal power supply. Please check if the power supply voltage and its polarity are correct. Besides, please confirm if wires connection and monitors are normal. Q: Unclear image output A: It is caused by incomplete adjustment of the lens back focus. Set focus from joystick attached on the camera wire. If not, please check if the lens is in good condition, or the lens surface and sensor surface exits foreign objects. If exits, it can be wiped by degreasing cotton swab or lens paper. Q: Horizontal interference fringes on image A: This phenomenon is generally caused by too strong hum bar of power supply, which needs to be filtered out. It may also be related to the used monitor or peripheral devices. Q: Constantly change of the ground color of image 21

23 A: This phenomenon is caused by color scrolling, which is mainly due to alternating electromagnetic field of fluorescent lamp, and the inherent phenomenon of camera. It can be weakened with two methods: one is to reduce the usage of fluorescent lamp. The other is to enlarge the distance with the camera. 22

Contents. 1 Notes Product Introduction Product Structure

Contents. 1 Notes Product Introduction Product Structure Contents 1 Notes...- 1-2 Product Introduction...- 2-2.1 Production Instruction... - 2-2.2 Product Feature... - 2-3 Product Structure...- 3-4 Technical Parameters...- 6-5 OSD Menu tree...- 7-6 Product Installation...-