Network Box Camera Quick Guide

Transcription

1 1 Network Box Camera Quick Guide V3.0.0 Hangzhou Hikvision Digital Technology Co., Ltd

2 1 1.Camera Description 1.1 Side Panel Description Serial NO. Description 1 Lens mount 2 Bracket mounting holes, used to fix the camera to the bracket 3 Auto iris interface

3 2 1.2 Rear Panel Description Rear Panel of DS-2CD886BF-E and DS-2CD876BF: Serial NO. Description 1 F1+ F1-, F2+ F2-, F3+ F3-: Alarm output interface 2 T1, T2, T3, T4, GND: Alarm input interface 3 D+,D-: RS-485 interface 4 10M / 100M self-adaptive Ethernet interface 5 Video output interface 6 RESET: Reset all parameters to factory default settings 7 TXD, RXD,GND: RS-232 interface 8 Power supply 9 Power LED indicator, which turns red when power is applied to the unit 10 SD card slot 11 Audio input interface 12 Audio output interface 13 Ground NOTE: When the camera is power up, press the RESET button for about 10 seconds, then all parameters, including user name, password, IP address, port number, etc., will be reset to the factory default settings.

4 3 Rear Panel of DS-2CD886MF-E and DS-2CD876MF: Serial NO. Description 1 ALARM OUT, GND: Alarm output interface ALARM IN, GND: Alarm input interface 2 D+, D-: RS-485 interface 3 TXD, RXD,GND: RS-232 interface 4 HDMI interface 5 RESET: Reset all parameters to factory default settings 6 10M / 100M self-adaptive Ethernet interface 7 Power supply 8 Power LED indicator, which turns red when power is applied to the unit 9 SD card slot 10 Audio input interface 11 Audio output interface 12 Ground NOTE: When the camera is power up, press the RESET button for about 10 seconds, then all parameters, including user name, password, IP address, port number, etc., will be reset to the factory default settings.

5 4 2.Installation Box camera can be fixed in both wall and ceiling, the following section introduces the ceiling mounting, and the wall mounting follows the same way: Step 1: Fix the camera mounting bracket to the ceiling. Fig 2.1 Fix camera mounting bracket NOTE: If it is wall, you need to fix the expand bolt (note: the mounting hole of the expand bolt should align with the bracket) before fixing the bracket as 1 in Fig 2.1. If the wall surface is wooden, the part of 1 in Fig 2.1 can be ignored and you can use the self-tapping screw to directly fix the bracket. Please note that the wall on which the camera is fixed should be able to bear at least three times the weight of the bracket and the camera. Step 2: Screw the mounting hole to the mounting bracket, and then adjust the camera to the desired monitoring location and finally tighten the knob on bracket to secure the camera to the ceiling.

6 5 Fig 2.2 Fix the Camera Step 3: Mount the camera lens: connect the VIDEO OUT interface of the camera to the debugging monitor, and adjust lens focus until you have obtained the clearest video images on the monitor, and then lock the lens. If required, loosen the knob on the mounting bracket and adjust the camera lens to the desired monitoring scene, and finally tighten the knob on bracket. Fig 2.3 Mount and adjust Lens

7 6 3.Search and Modify IP SADP (Search Active Devices Protocol) software can automatically search the IP address of network cameras on the same network with connection diagram as follows: The operation of searching and modifying IP address is described as following: 1. Install the SADP software, and then run the sadpdlg.exe 2. Search IP address. Click it Show the IP address of the camera 3. Modify IP address.

8 7 1. Click [modify] 2. Input new IP address and the password ( Default: 12345) of the camera, then click [save] 3. Modify successfully

9 8 4.Preview via IE browser Note: The default IP of network cameras is with admin as the administrator, as the password, and 8000 as the default port. For monitoring camera images, a comptuer running the Microsoft Windows Operating System and Internet Explorer (Version 6.0 or later) are required. In this manual, we take Windows XP and IE 6.0 for example. This chapter describes how to view the video from the camera via web browser, and operate as following: 1. Open the IE browser, set the security level to [Medium] in *Tools/InternetOptions/Security/Custom Level +

10 9 2. Type the IP address of the camera and press [Enter], and then click the mention box that pop up. 3. Click [Run] to install the ActiveX control.

11 10 4. Input Username (Default: admin), Password (Default: 12345) and Port (Default: 8000) of the camera, then click [Login]

12 11 5. View the image For detailed instructions of further configuration, please refer to the user manual of network camera.

13 12 First Choice for Security Professionals