OWNER'S MANUAL PLEASE READ CAREFULLY BEFORE USING AND KEEP WELL. 7" DIGITAL WATERPROOF LCD MONITOR FOR HEAVY DUTY INDUSTRY

Transcription

1 OWNER'S MNUL PLESE RED CREFULLY BEFORE USING ND KEEP WELL. 7" DIGITL WTERPROOF LCD MONITOR FOR HEVY DUTY INDUSTRY Model: ECL-770WP Design and Specifications are subject to change without notice.

2 OWNER'S RECORD Model No. Serial No. ECL-770WP WRNING No! 2

3 SUGGESTIONS 7" DIGITL WTERPROOF LCD MONITOR FOR HEVY DUTY INDUSTRY 1 Safety - Use only DC 10V ~ DC 32V. - In case that dust or liquid was soaked into the case, please turn off power and consult an experienced technician before using. 2 Installation - Do not install the unit in an extremely hot or humid place (radiator, air duct, etc.) or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. - If your vehicle has been parked in direct sun light resulting in a considerable rise in temperature inside the vehicle, allow the unit to cool off before operating. 3 General cleaning information - Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit. 3

4 PLESE RED CREFULLY BEFORE USING ND KEEP WELL. Design and Specifications are subject to change without notice. r FETURES - W a t e r R e s i s t a n c e ( I P 6 8 ) - 7 " D i g i t a l L C D W i d e P a n e l - u t o N T S C / P L D e t e c t i o n - u t o D Y / N I G H T D e t e c t i o n - V a n d a l R e s i s t a n c e ( l H o u s i n g ) - P a r k i n g D i s t a n c e M a r k e r S e t t i n g v a i l a b l e - C a p a c i t i v e T o u c h K e y - Support Multi-Functional Camera (CM1 &CM2): Normal/Shutter/Tilt r PCKGE CONTENTS Please check that you have the correct contents before using this product. If any items are missing, please contact your dealer. (SCREW TYPE) OR ECL-770WP MONITOR SUNVISOR (RIL TYPE) STND BRCKET OPTIONL OWNER'S MNUL 7" DIGITL WTERPROOF LCD MONITOR FOR HEVY DUTY INDUSTRY C1 C2 Model: ECL-770WP POWER CORD SCREW KITS INSTRUCTION MNUL 4

5 OPERTIONS POWER 2 ECT 3 4 UP 5 DOWN 6 DY/NIGHT SENSOR (CDS) POWER Touch to turn the monitor on. Touch to turn the monitor off. 2 NOTE Monitor start mode will follow UTO POWER SETTING 2 ECT Touch Touch to select CMER. to select the option in SET UP. 3 Use to enter Display Menu(Short key) and Main Menu(Long key). Touch once to enter menu mode. Touch again to from menu mode. Selectable OSD Menu Disappears within 7 sec if there s no new button pressed. Touch menu button over 2 sec to go back to main menu from submenu. 5

6 OPERTIONS 4 UP 5 DOWN While in Menu mode and navigate though the available menu options. Touch to adjust Bright, Contrast, Color, Tint Volume and other setting values. 6 DY/NIGHT SENSOR (CDS) utomatic Brightness Control The brightness of the monitor is adjusted automatically with the CDS accordingly to the circumstance. 6

7 OPERTIONS. DISPLY ECT Short Key (more than 0.5 sec) DN ECT Option setting DISPLY BRIGHT CONTRST COLOR TINT BRIGHT CONTRST (0~60) (0~60) COLOR 30 (0~60) PL MODE NTSC MODE TINT (0~60) 30 * TINT menu is displayed in NTSC only. 2 NOTE User can adjust Display setting value for CM1 and CM2 channel separately. 7

8 OPERTIONS. SETUP Touch button for a while (over 2 sec) to enter MIN. Selectable OSD disappears within 7 sec if there is no new button pressed. long key (more than 2 sec) up / down ECT MIN 1. CMER SETTING 2. TRIGGER SETTING 3. UTO SCN SETTING 4. DY/NIGHT SETTING 5. DVNCED 1 CMER SETTING 1. CMER SETTING CM1 CM2 Camera s mirror/normal image can be changed (CM1/CM2 separate control). Camera s up/down image can be changed (CM1/CM2 separate control). Different types of camera (Normal/Shutter/Tilt) can be connected to CM1/CM2. Each camera can be named and the selected camera name is displayed via OSD. NOR/MIR : [MIRROR;NORML] UP/DOWN : [ U P ; D O W N ] N M E : [ C M 1 ] SORT:[NORML;SHUTTER; TILT.T;TILT.MT] NOR/MIR : [MIRROR;NORML] UP/DOWN : [UP;DOWN] NME : [CM1 ] ECT CM1,CM2 selecting name setting SORT:[NORML;SHUTTER;TILT.T; TILT.MT ] ECT selecting ECT CM1,CM2 ECT ECT 2 NOTE Select camera type between NORML, SHUTTER, TILT UTOMTIC or TILT MNUL. How to control TILT MNUL: Select TILT.MT. Get out from. Press key two times and you can see below OSD. TILT CONTROL: Press key for TILT UP. Press key for TILT DOWN. 8

9 OPERTIONS 2 TRIGGER SETTING 2. TRIGGER SETTING TRIGGER1 TRIGGER2 SOURCE:[CM1;CM2; SKIP] DELY:[0~20sec] MRKER:[TYPE1;OFF] MRKER SETTING SOURCE:[CM1;CM2;SKIP] selecting Trigger1,Trigger2 User can use 2 triggers and each trigger source(cm1;cm2;skip) can be selected. When the trigger is activated, the selected source s image is displayed. 2 DELY:[0~20SEC] 2 NOTE Priority of trigger when triggers are engaged at the same time:trigger1>trigger2 Each trigger's delay time is adjustable from 0 sec to 20 sec. NOTE Delay time setting is only available with. ECT If one camera is activated by an intermittent signal ( e.g. from an indicator light s ) the delay must be activated to prevent the picture from flickering. ECT ECT selecting ECT Trigger1,Trigger2 ECT MRKER:[TYPE1;OFF] Trigger1, Trigger2 LEFT-RIGHT TYPE1 UP-DOWN WIDTH ECT ECT LEFT-RIGHT UP-DOWN WIDTH selecting MRKER SETTING LEFT-RIGHT UP-DOWN TYPE1 ECT ECT ECT selecting selecting selecting 2 NOTE If MRKER is set as OFF, Parking aid marker is not displayed when the reverse gear is engaged. 9

10 OPERTIONS 3 UTO SCN SETTING 3. UTO SCN SETTING UTO SCN:[ON;OFF] CM1 DELY:[0~20sec] CM2 DELY:[0~20sec] CM1 DELY CM2 DELY UTO SCN:[ON;OFF] ECT ECT ECT 2 NOTE uto scanning time of each camera can be adjusted from 0 sec to 20 sec. uto scan delay time setting is only available with. ECT To give a pause while scanning, press. ECT When user select 0 sec for one channel, monitor skip scanning the channel. 4 DY/NIGHT SETTING 4. DY/NIGHT SETTING SENSOR:[ON;OFF] SENSOR:[ON;OFF] SENSITIVITY:[0~60] NIGHT BRIGHT:[0~60] SENSITIVITY:[0~60] ECT NIGHT BRIGHT:[0~60] ECT ECT User can set the level of Day/Night sensor sensitivity and night bright. 10

11 OPERTIONS 5 DVNCED 6. DVNCED UTO POWER:[OFF;ON;UTO] UTO POWER: [OFF;ON;UTO] FCTORY RESET ECT FCTORY RESET ECT 2 NOTE UTO Setting: Monitor keeps the last setting in memory: Monitor will start up Power-on mode or Stand- by mode according to its last mode before the ignition key off. OFF Setting: Monitor keeps Stand- by setting regardless of the last mode before the ignition key off. ON setting: Monitor will be turned on automatically when ignition key on regardless of the last mode of the monitor before the ignition key off. 11

12 r INSTLLTION 1 DSH BORD SCREW MONITOR 1-1. STND BRCKET(SCREW FIXING TYPE) 1-2. STND BRCKET(RIL TYPE) 2 SUNVISOR MONITOR 12

13 SYSTEM CONNECTIONS POWER/TRIGGER WIRE FUNCTIONS FUSE REF # WIRE COLOR DESCRIPTION 1 WHITE TRIGGER2 2 GREEN TRIGGER1 3 BLCK GROUND 4 RED POWER IN DC (10 to 32V) C1 C2 C1 C2 CMER (Not supplied) * Normal / Tilt / Shutter camera 13

14 SPECIFICTIONS Model: ECL-770WP Power Input Power Consumption Video System Panel Resolution Format Display Mode Camera input(2ch) Operating Temp. Storage Temp. Vibration I.P Factor OSD Control Dimension Weight Supplied acc y DC 10V~32V Max. 12Watt NTSC / PL compatible 7" Digital 800 (H) X3(RGB) X 480 (V) pixels 16:9 wide Single Mini DIN 4P, 1Vp-p 75Ω -30 ~ +80 ( -22 ~ 176 ) -40 ~ +85 ( -40 ~ 185 ) 10G IP 69K Day & Night Sensor Bright, Contrast, Color, Tint Mirror/Normal, Day/Night Mode/Scale *Individual Control per Channel available 194(W) X 124(D) X 51(H) mm 7.6(W) X 4.8(D) X 2.0(H) inch pprox. 850g Power Cord (1) Screw Kit (1) Stand Bracket (1) Sun Visor (1) Instruction Manual (1) 14

15 THIS SYMBOL MENS DO NOT DISPOSE OF S MUNICIPL WSTE. RE-USE OR RECYCLE WHEREVER POSSIBLE. ELECTRICL / ELECTRONIC COMPONENTS MY CONTIN SUBSTNCES WHICH RE HRMFUL TO THE ENVIRONMENT. FOR ENVIRONMENTLLY SOUND METHODS OF DISPOSL, PLESE CONTCT YOUR LOCL GOVERNMENT UTHORITY. 15

16 16 Part no.6mnel770wp-02 printed in korea