Promaster Chassis Cab and Cut Away Loose Ship Back Up Camera System

Size: px
Start display at page:

Download "Promaster Chassis Cab and Cut Away Loose Ship Back Up Camera System"

Transcription

1 Starting in model year 2016, the RAM Promaster Chassis Cab and Cut Away are offered with a rear camera option. The package sales code is XA3. Included in this option package are an 11 meter video cable (Part Number AB) and a user mountable camera. (Part Number AA) In order to get this option, you must also order the RA2, U Connect 5.0 radio. This Jumper-Camera kit is packaged within a plastic bag located in the driver s compartment of the vehicle. The camera will be installed by the up fitter or customer in a location best suited to the particular up fit and the end user s needs. Page 1 of 9

2 Camera Location The first step is to determine the best location for the camera. The camera location is dependent on end user needs and the availability of suitable locations on the up fit. Sometimes, this can be a tradeoff. This system was designed to be a backup camera. The picture is only available when the vehicle is in reverse. So, using the system as a cargo view may not be practical. Typically, the camera will be mounted at the rearward most edge of the vehicle, as close to the lateral center line as possible and as high up as you can get it. The down angle will be in the area of 30 degrees. The mounting location and down angle can be adjusted to achieve the desired view. Unlike the van, the chassis cab and cut away camera does not have guide lines. No need to worry about guide line accuracy. Cable Routing One end of the video cable has a black plug and a ground eyelet. These connections are made behind the trim panel in the driver s side foot well. The other end of the cable has a grey connector on it. That will connect to the pig tail on the camera. Routing the cable from the camera through the up fit is left to the discretion of the camera installer and the desires of the owner. In the case of the cut away, there is plenty of opportunity to route the cable into the cab. On the chassis cab, the opportunity is limited. Unless the camera installer wishes to cut a small hole in the cab back, the only way in is through a rubber body plug located below the passenger side B pillar in the rear of the body. See pictures on the next page. Page 2 of 9

3 Page 3 of 9

4 This hole can be accessed on the inside of the body by removing the trim panel at the base of the passenger side B pillar then removing the plastic electrical block housing. See pictures below. Electrical Block Housing Inside of Body Plug Remove the body plug and pierce a hole through the center of the plug. Using a pair of needle nose plies, stretch the hole. Be careful not to rip the plug. Once the rubber is sufficiently worked, the grey connector can be passed through the plug. Once the installation is complete and the camera cable is secured into place, fill the recessed area of the outside of the body plug with RTV. Fill this Area with RTV Page 4 of 9

5 To create clearance to pass the cable between the electrical block housing and the body, a small notch can be cut into the bottom of the electrical block housing. Notch The cable can be routed through the notch and under the floor pad behind the seats to the driver s side foot well. Route the cable through the white plastic wire trough down into the foot well. Camera Cable Wire Trough Camera Cable Page 5 of 9

6 In Cab Electrical Connections The black plug on the camera cable mates to a black connector in the body harness. The eyelet goes onto a ground stud located on the vertical sheet metal of the foot well. Both are located behind the trim panel in the driver s side foot well. Remove the cap on the harness connector and connect the camera cable. A click will be heard when a secure connection has been achieved. The ground stud will have two nuts. Remove the top nut and place the eyelet on the camera cable between the top and bottom nuts. Body Harness Connector Ground Stud Camera Cable Page 6 of 9

7 Camera Mounting Unless the camera can be mounted directly to the up fit, a bracket will need to be fabricated. If practical, it is desirable to mount the camera in a location where the connector on the end of the pig tail can be inside the up fit and shielded from the outside environment. In this particular case, the vehicle was up fit with a flat bed. The camera was mounted to the rear of the flat bed. A bracket was fabricated to securely hold the camera and offer as much protection as possible. The bracket was designed to provide a down angle that will allow the ground to come into view at a point directly below the reward most edge of the vehicle. In this case, it was not possible to get the pig tail in a dry environment. If this is the case with your up fit, you may want to consider covering the connection with a sealing heat shrink tube. Page 7 of 9

8 The bracket show above is just an example of what can be done. Bracket designs can vary depending upon the up fit they are mounted to and the creativity of the camera installer. Camera Electrical Connections Insert the black connector on the end of the camera pig tail into the grey connector on the camera cable. A click will be heard when a secure connection has been achieved. If this connection cannot be located in a dry environment inside the up fit, some sort covering for that connection should be considered. Either via a fabricated enclosure or a sealing heat shrinkable tubing. Camera Pig Tail Camera Cable Page 8 of 9

9 Finishing Up Promaster Chassis Cab and Cut Away Take care to prevent in-use impact and abrasion damage. Add a protective covering (such as convolute) if prudent. Clean up and/or cover sharp or abrasive edges in the sheet metal. Secure the cable (using clips/straps) often in its routing path. Don t forget to fill the outside of the body plug below the B pillar with RTV. Once the camera is connected, the camera system will start to function. There are no electronic configuration changes that need to be made. The camera view will be displayed on the radio screen when the vehicle is shifted into reverse. Page 9 of 9

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines Installation Instructions (Kit # )

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines Installation Instructions (Kit # ) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in Kit: Chassis Harness Power Harness with RCA connectors Camera mounted on license plate bracket

More information

CHASSIS CAB / PICKUP BACK UP CAMERA

CHASSIS CAB / PICKUP BACK UP CAMERA Overview System Variations The backup camera sales code is XAC. All ram back up camera systems use a common analog camera. Depending upon vehicle option content, the video monitor will either be in the

More information

ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.

ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. Required for Install: ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. 1. Chrysler/Dodge/Jeep vehicle with Uconnect

More information

Please read thoroughly before starting installation and check that kit contents are complete.

Please read thoroughly before starting installation and check that kit contents are complete. Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2015 F-150 8 MyTouch factory display 360º Vision System (Kit # AVMS-3618) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING -Must

More information

INSTALLATION INSTRUCTIONS:

INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: Part # SV-5600 PC-F Full Frame Type (Black or Chrome) Part # SV-5500 PC-B Top Bar Type (Black or Chrome) Part # SV- PK Kits with PlateCam and 3.5 LCD monitor FEATURES: Revolutionary

More information

Encore XT Manual Gun Upgrade Kit

Encore XT Manual Gun Upgrade Kit Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.

More information

Model: ACA400 & ACA500 Reverse Camera Installation Manual

Model: ACA400 & ACA500 Reverse Camera Installation Manual Model: ACA400 & ACA500 Reverse Camera Installation Manual ACA400 ACA500 FEATURES: High Resolution: 1/4 CMOS Color Camera Compact Zinc Alloy Die Cast Body Waterproof Housing 150 Degree Wide View Angle Minimum

More information

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100800 1 Cable Installation Kit 2000901-1 1 Dielectric Grease 2002872

More information

GM NBS Truck CCD Backup Camera Kit Installation Guide

GM NBS Truck CCD Backup Camera Kit Installation Guide CS GM1 GM NBS Truck 2007 2012 CCD Backup Camera Kit Installation Guide Thank you for your purchase! These instructions are intended for the do it yourselfer who decides to install the camera without professional

More information

DirectCommand Installation RoGator Model Year Ag Leader Technology

DirectCommand Installation RoGator Model Year Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100801 1 Dual Lock 2000052-9 1 Dual Lock 2000053-9 1 Quick Reference

More information

Ag Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series

Ag Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394

More information

Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features

Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera. High Resolution, 1/2 CMOS Color Camera

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS UTV/Rockcrawler Quad Camera and DVR Monitor (Kit #SUTV-1040) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Roll Bar Mounts (1.5

More information

INTERCOM AMBULANCE/RESCUE VEHICLE MODEL ICA100 SURFACE MOUNT SERIES MODELS ICA200, ICA300 FLUSH MOUNT SERIES MODELS ICA400, ICA500

INTERCOM AMBULANCE/RESCUE VEHICLE MODEL ICA100 SURFACE MOUNT SERIES MODELS ICA200, ICA300 FLUSH MOUNT SERIES MODELS ICA400, ICA500 Document Number: XE-ICA1PM-R0A ICA100 Rev171109 INTERCOM AMBULANCE/RESCUE VEHICLE MODEL ICA100 SURFACE MOUNT SERIES MODELS ICA200, ICA300 FLUSH MOUNT SERIES MODELS ICA400, ICA500 ICA100 ICA200/300 ICA400/500

More information

SV-6400 ClipCam SAFETY PRECAUTIONS

SV-6400 ClipCam SAFETY PRECAUTIONS SV-6400 ClipCam SAFETY PRECAUTIONS Make sure to read the Installation Manual for safety precautions before installing unit or accessories. Please make sure the vehicle is well parked in a safe place. Make

More information

Navigation interface for Jeep GC 5 RA2 NTV-KIT581

Navigation interface for Jeep GC 5 RA2 NTV-KIT581 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.

More information

Note: These installation instructions are only for the 4430/4440 Sprayer. For other SPX models please refer to P/N , &

Note: These installation instructions are only for the 4430/4440 Sprayer. For other SPX models please refer to P/N , & DirectCommand Installation Ag Leader Technology Note: These installation instructions are only for the 4430/4440 Sprayer. For other SPX models please refer to P/N 2005944, 2005945 & 2006383. Part Name/Description

More information

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100852 1 Cable Installation

More information

DirectCommand Installation 5 Channel Spreader Control Module Technology

DirectCommand Installation 5 Channel Spreader Control Module Technology DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100582 1 Cable Installation

More information

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the

More information

Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL)

Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the paint)

More information

Ag Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount)

Ag Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount) Part Name / Description Part Number Quantity DirectCommand Hardi Sprayer Kit 4100882 1 Dust Receptacle 8-pin 2002975-8C 1 Installation Instructions 2006335 1 Quick Reference Card- Liquid Application 2002831-38

More information

NTG3-SL NTV-KIT142. Overview Mercedes-SL. Backup camera / AV input / RSE / Video In Motion interface. Kit Contents. NTG3 Module NTV-ASY171

NTG3-SL NTV-KIT142. Overview Mercedes-SL. Backup camera / AV input / RSE / Video In Motion interface. Kit Contents. NTG3 Module NTV-ASY171 NTG3 5.04.14 NAV-TV 3950 NW 120 Ave, Coral Srings, FL NTV-KIT142 Overview 2009-2011 Mercedes-SL Backup camera / AV input / RSE / Video In Motion interface Kit Contents SMB to RCA NTV-CAB007 Plug & Play

More information

370Z Reversing Camera Installation Instructions

370Z Reversing Camera Installation Instructions 370Z Reversing Camera Installation Instructions Concept how it works When Nissan first sold the 370Z with Premium Connect there was no option for a reversing camera. However, provision was made for one

More information

If technical support is required, please contact Advent Technical Support at

If technical support is required, please contact Advent Technical Support at Document 128-9011 Created 11/21/11 Kit Contents: Item # Qty. Component Description 1 2 Monitor Assembly 2 2 Remote Control 3 1 Cables # 3 4 1 Metal Wire Puller 5 1 Power Cord # 9 6 1 Owners Manual 7 2

More information

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed

More information

Parts and Accessories Installation Instructions

Parts and Accessories Installation Instructions Parts and Accessories Installation Instructions ON TP CD Rad Nav BMW MINI Info OK 5 77 B Mini Traffic Pro installation kit (cars with Radio Wave only) Mini (R5/R53) Technical and electrical knowledge required

More information

UCIT LIVE HD 4 Camera DVR. Installation Manual. 1/18 Version 1.0

UCIT LIVE HD 4 Camera DVR. Installation Manual. 1/18 Version 1.0 UCIT LIVE HD 4 Camera DVR Installation Manual 1/18 Version 1.0 This is a step by step guide that will walk you through installing the UCIT LIVE HD 4 Channel Camera System. Basic wiring experience and knowledge

More information

Gateway Profile 4 service guide

Gateway Profile 4 service guide Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................

More information

Ag Leader Technology. DirectCommand Installation RoGator Model Years

Ag Leader Technology. DirectCommand Installation RoGator Model Years Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100550 1 Dual Lock 2000052-9 1 Dual Lock 2000053-9 1 Hardware Kit

More information

Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL. Intro Camera Operation Installation - Wrangler JK... 2

Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL. Intro Camera Operation Installation - Wrangler JK... 2 Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL CONTENTS Intro... 1 Camera Operation... 2 Installation - Wrangler JK... 2 Jippo Play Configuration... 6 VES Installation... 7 Camera Installation...

More information

Assembly of the TACOS WAT-910BD Housing v2

Assembly of the TACOS WAT-910BD Housing v2 1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers

More information

12.3 Pro Dash Quick Start Guide

12.3 Pro Dash Quick Start Guide 12.3 Pro Dash Quick Start Guide 553-111 CONTENTS: Package Contents... 3 Mounting... 3 Connections... 4 Main Connector... 4 CAN Extension Harness... 6 USB... 7 GPS Antenna... 7 Cleaning... 7 Touchscreen

More information

NTG3 / NTG3E /NTG3SLK NTV-KIT102/106/189. Overview up Mercedes GL/ML/R/E/CLS/SLK. Backup camera / AV input / RSE / Video In Motion interface

NTG3 / NTG3E /NTG3SLK NTV-KIT102/106/189. Overview up Mercedes GL/ML/R/E/CLS/SLK. Backup camera / AV input / RSE / Video In Motion interface NTG3 5.04.14 NAV-TV 3950 NW 120 Ave, Coral Srings, FL NTG3 / NTG3E /NTG3SLK NTV-KIT102/106/189 Overview 2009-up Mercedes GL/ML/R/E/CLS/SLK Backup camera / AV input / RSE / Video In Motion interface Kit

More information

Part Name/Description Part Number Quantity

Part Name/Description Part Number Quantity Part Name/Description Part Number Quantity Direct Command Kit 4100883 1 Installation Instructions 2006336 1 Hardware Kit Large Module 2001354-1 2 Cable Installation Kit 2000901-1 1 Quick Reference Card

More information

Now with Picture Memory

Now with Picture Memory Intrasonic Technology, Inc. Color Video Door Phone / Intercom Installer s Manual Model No.V304KIT-R Now with Picture Memory Please read this manual carefully before the products are installed.technical

More information

A Backlighted LCD for your K1

A Backlighted LCD for your K1 A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification

More information

UCIT LIVE HD 4 Camera DVR. Installation Manual. 10/17 Version 2.0

UCIT LIVE HD 4 Camera DVR. Installation Manual. 10/17 Version 2.0 UCIT LIVE HD 4 Camera DVR Installation Manual 10/17 Version 2.0 Always Check https://www.safetytrack.net/camera-installation-and-user-manuals/ for the most up to date version of this installation guide.

More information

Installation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio

Installation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio Introduction The following instruction procedure is for the RGB interface to a GM 05 Nav Radio as part of the Webasto Product NAVCam Back-up Camera (VCP-0000220). In addition, an installer will need to

More information

Part Name/Description Part Number Quantity

Part Name/Description Part Number Quantity Part Name/Description Part Number Quantity Direct Command 4200159 1 Cable Installation Kit 2000901-1 1 Hood 37-pin DSub 2001808-37 2 Dielectric Grease 2002872 1 Dust Plug 12 Pin Gray 2002899-12N 1 Feature

More information

How to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC Chip

How to build an Olympus D-360L Trail Camera using the PixController Universal Digital Trail Camera Kit w/ RS-232-U PIC Chip Copyright, PixController, Inc. http://www.pixcontroller.com, all rights reserved. How to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC

More information

Raven Adapter Harness

Raven Adapter Harness Note: Indented items indicate parts included in an assembly listed above Quantity by System Part Name/Description Part Number With Switch Box With Built-in Switches Raven Harness Adapter Kit 4100504 1

More information

DirectCommand Installation CASE IH SPX Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 19

DirectCommand Installation CASE IH SPX Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 19 Note: These installation instructions only cover installation on SPX 4420 Sprayers only. For installation on SPX 3230/3330 Sprayers refer to Installation Instructions P/N 2005945. For SPX 4430 refer to

More information

W205-RVC NTV-KIT580. Overview

W205-RVC NTV-KIT580. Overview 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-RVC NTV-KIT580 Overview The W205-RVC Kit allows the user to add a backup camera input (with

More information

UCIT LIVE HD 4 Camera DVR. Installation Manual. 10/17 Version 2.0

UCIT LIVE HD 4 Camera DVR. Installation Manual. 10/17 Version 2.0 UCIT LIVE HD 4 Camera DVR Installation Manual 10/17 Version 2.0 This is a step by step guide that will walk you through installing the UCIT LIVE HD 4 Channel Camera System. Basic wiring experience and

More information

KP1S Installation Guide with INT1S Power Adaptor

KP1S Installation Guide with INT1S Power Adaptor KP1S Installation Guide with INT1S Power Adaptor 1. KP1S Windshield Mounting Apply provided 3M VHB adhesive pad to the mounting bracket and press firmly to adhere. Clean the windshield with alcohol and

More information

REC-AV XG NTV-KIT276

REC-AV XG NTV-KIT276 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com REC-AV XG NTV-KIT276 Overview The REC-AV XG adds video input (including rear camera) for select

More information

Instructions to Install Retrofit Kit 6/7000 Machine

Instructions to Install Retrofit Kit 6/7000 Machine Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER

More information

21. Connect the preinstalled antenna leads to the SDAR antenna leads (Figure 8).

21. Connect the preinstalled antenna leads to the SDAR antenna leads (Figure 8). 21. Connect the preinstalled antenna leads to the SDAR antenna leads (Figure 8). Note: Make sure the connectors lock into the plastic connector lock-clips. 22. Insulate the coupled connectors with felt

More information

TENSIONED DESCENDERPRO

TENSIONED DESCENDERPRO Motorized projection screen for ceiling recessed installations Product specifications: Ceiling recessed electrically operated projection screen 230 volt (50Hz) with a usage of no more than 3 Ampere (98.9

More information

TECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2

TECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2 document Page 1 of 18 TECHKNOW, INC Kiosk Order Confirmation System INSTALLATION MANUAL Revision Date: July 11, 2012 Part # Version 3.2 Techknow, Inc. 393 Mayfield Road Duncan, SC 29334 www.gotechknow.com

More information

EMC 10T "CE" Mechanical Upgrade Procedure

EMC 10T CE Mechanical Upgrade Procedure EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines

More information

Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox

Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR

More information

SMM501/501-H (Surveillance Mode Module) Ford Police Interceptors (Sedan and SUV)

SMM501/501-H (Surveillance Mode Module) Ford Police Interceptors (Sedan and SUV) An ISO 9001:2008 Registered Company SMM501/501-H (Surveillance Mode Module) 2013-2014 Ford Police Interceptors (Sedan and SUV) Introduction The SMM501/501-H is intended for 2013 and 2014 Ford Police Interceptors

More information

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator.

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document

More information

Canon Powershot S200 Camera lens Replacement

Canon Powershot S200 Camera lens Replacement Canon Powershot S200 Camera lens Replacement This guide will walk you through the process of removing the camera's lens for replacement. Written By: Joseph Melo Page 1 of 16 INTRODUCTION The lens is used

More information

Havis Integrated Control System Installation Instructions for Standard* Ford Police Interceptor Utility

Havis Integrated Control System Installation Instructions for Standard* Ford Police Interceptor Utility Installation Instructions for Standard* Ford Police Interceptor Utility Does not properly fit instrument panel in an Interceptor Utility with Interior Upgrade Code 65U Upgrade Package Includes: Cloth Seats

More information

FITTING INSTRUCTIONS

FITTING INSTRUCTIONS & This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one

More information

Rexroth Controller Installation & Operations Manual

Rexroth Controller Installation & Operations Manual Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Rexroth - 105 Controller Installation & Operations Manual The Drive & Control Company Table of Contents:

More information

FASCIA LIGHTS - 4 EMPS2QM(x)(x) - QUICK MOUNT EMPS2SMS(x)(xxx)- SCREW MOUNT EMPS2STS(x)(xxx) - STUD MOUNT THREADED WIRE HOOK-UP TABLE

FASCIA LIGHTS - 4 EMPS2QM(x)(x) - QUICK MOUNT EMPS2SMS(x)(xxx)- SCREW MOUNT EMPS2STS(x)(xxx) - STUD MOUNT THREADED WIRE HOOK-UP TABLE FASCIA LIGHTS - 4 EMPS2QM(x)(x) - QUICK MOUNT EMPS2SMS(x)(xxx)- SCREW MOUNT EMPS2STS(x)(xxx) - STUD MOUNT THREADED TORX DRIVE SREWS x2 TECHNICAL SPECIFICATIONS Dimensions (From Mounting Surface) Screw

More information

GENUINE PARTS. ipod INSTALLATION INSTRUCTIONS

GENUINE PARTS. ipod INSTALLATION INSTRUCTIONS GENUINE PARTS. DESCRIPTION: ipod Interface 2. PART NUMBERS: ipod INSTALLATION INSTRUCTIONS ipod Gateway Module Kit N-Bus harness for ipod Gateway N-Bus harness for SAT (with factory SAT only) 999U7-ST000

More information

Experimental Procedure

Experimental Procedure 1 of 14 9/10/2018, 11:38 AM https://www.sciencebuddies.org/science-fair-projects/project-ideas/robotics_p028/robotics/obstacle-avoiding-robot (http://www.sciencebuddies.org/science-fair-projects /project-ideas/robotics_p028/robotics/obstacle-avoiding-robot)

More information

DirectCommand Installation DirectCommand Complete Wiring Harness

DirectCommand Installation DirectCommand Complete Wiring Harness Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number With Switch Box Quantity by Model With Boom Switch Cable Display Cable Kit 4100814 1 1 Power Control

More information

PLCMTR Commercial Grade Camera System

PLCMTR Commercial Grade Camera System Please read instructions carefully before installation and use. Installation should be performed by a professional installer. To ensure your safety, the driver should not watch videos or operate features

More information

xtablet T1600 Vehicle Holder Installation Guide

xtablet T1600 Vehicle Holder Installation Guide This document will step you through setting up the T1600 Vehicle Holder installation and tips for a safe, clean and long lasting installation. Preparing to Mount the Vehicle Holder Warning : Dock mounting

More information

LANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS

LANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS LANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS Navigation (MMCS) unit Camera Thank you for purchasing the Mitsubishi Genuine Accessory. To install

More information

Elecraft K3 KREF3 Output Level Modification

Elecraft K3 KREF3 Output Level Modification Elecraft K3 Revision A, September 15, 2015 Copyright 2015, Elecraft, Inc. All Rights Reserved Introduction This modification increases the output levels from the KREF3 Reference Oscillator to provide proper

More information

*E * E E0606

*E * E E0606 75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche

More information

PARTS DESCRIPTION LISTING

PARTS DESCRIPTION LISTING PARTS DESCRIPTION LISTING Form 4-157e, 11-09 Sheet 2 of 6 Index No. Part Number Description A 16-889-1 TUBE ASSEMBLY, CAMERA SUPPORT CM (See Sheet 5) B 69-1063-1 COVER, ASSEMBLY BACK DSP600 (See Sheet

More information

Megatouch FORCE Monitor Chassis Board Replacement

Megatouch FORCE Monitor Chassis Board Replacement Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis

More information

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole

More information

Linear Actuator Controller

Linear Actuator Controller Product Data Sheet Linear Actuator Controller Standard Features: 3 user programmable actuator travel set points 12 VDC (nominal) 7.5 Amp fuse Control box and wired 3-button switch: No IP rating (not waterproof)

More information

MY-CUE-Kit NTV-KIT457

MY-CUE-Kit NTV-KIT457 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com MY-CUE-Kit NTV-KIT457 Overview The MY-CUE Kit allows the user to add up to 3 audio/video inputs

More information

Microsystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015

Microsystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015 UM Unified Microsystems SCI-6 Sound Card Interface Kit Version 1.09 January 2015 The SCI-6 interface was designed to be a low cost, high quality interface between your PC s sound card and radio transceiver.

More information

SERVICE PARTS MANUAL

SERVICE PARTS MANUAL SERVICE PARTS MANUAL DX SERIES SNOW PLOW FOR SERIES SNOW PLOWS SERIAL NUMBERS AFTER DX0000 00 Sno-Way International 0G TABLE OF CONTENTS Page HYDRAULIC SYSTEM (DX)... POWER PACK FRAME... 3 BLADES... LIFT

More information

ClearPix Motorized Screen In-Ceiling Casing Slot Version Installation Manual. Revision G

ClearPix Motorized Screen In-Ceiling Casing Slot Version Installation Manual. Revision G ClearPix Motorized Screen In-Ceiling Casing Slot Version Installation Manual Revision G 2007.04.23 Action: W: Written R: Page revised A: Page added D: Page deleted C: Rewritten completely Date Rev. N

More information

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :36-26 May

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :36-26 May SCdefault 900 Installation instructions SITdefault Upgrade to Prestige 300 sound system MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group

More information

Wireless 4.5 LCD Display System

Wireless 4.5 LCD Display System Wireless 4.5 LCD Display System Model: ACA450 Installation/User Manual Features: 4.5" TFT Color LCD Display On Screen Display Function 2.4 GHz Wireless Receiver Automatically Displays Image when Vehicle

More information

SIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285

SIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 SIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285 BHM Overview The SIR-PCM3 adds Sirius

More information

EMC 10/4 "CE" Mechanical Upgrade Procedure

EMC 10/4 CE Mechanical Upgrade Procedure EMC 10/4 "CE" Mechanical Upgrade Procedure Kit Part Number: 009663-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS GM MyLink Camera Interface for 7-inch IOB Display Radios 2016 to Current (Kit # 9002-2765) ***NOTE: VERIFY YOU HAVE AN IOB RPO CODE located on the OEM RPO sticker (glove box or spare tire well). If the

More information

NOTE: Read the instructions completely through before beginning actual installation.

NOTE: Read the instructions completely through before beginning actual installation. CONSOLE CONNECTOR KIT 7850 INSTALLATION INSTRUCTIONS FOR USE WITH: Various Two-channel Organs LESLIE Speaker Models 705, 705C, 720 KIT CONTENT Console Connector 138488 Switch Assembly, Cable Assembly,

More information

TURCK Industrial Connectivity Products

TURCK Industrial Connectivity Products TURCK Industrial Connectivity Products General Accessories Liquid Tight Strain Relief Cable Glands Lock Nuts Page R2 - R4 Page R6 Snap-in Labels Strain Relief Cord Grips Page R5 Page R5 Protective Sleeving

More information

PLEASE NOTE: These instructions are intended to be used by a person with average mechanical and electrical skills.

PLEASE NOTE: These instructions are intended to be used by a person with average mechanical and electrical skills. ClassicLEDs is please to present their latest line in Corvette LEDs. This covers the 1975 thru 1979 Corvette. This systems does not include the Corvette... PLEASE NOTE: These instructions are intended

More information

3950 NW 120 th Ave, Coral Springs, FL TEL FAX MFT F-CAM. Force Front Camera Module NTV-KIT831 BHM 07/31/18 NTV-DOC298

3950 NW 120 th Ave, Coral Springs, FL TEL FAX MFT F-CAM. Force Front Camera Module NTV-KIT831 BHM 07/31/18 NTV-DOC298 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 MFT F-CAM Force Front Camera Module NTV-KIT831 BHM 07/31/18 Overview The MFT F-CAM module uses OEM buttons (or wire triggers)

More information

What s in the Box? REAR VIEW SAFETY

What s in the Box? REAR VIEW SAFETY TM 1 What s in the Box? 1 Full HD Color Infra-red Weather Proof Camera 1 Full HD 7" TFT LCD Color Monitor w/monitor Mount 1 Power Harness 1 66 Camera Cable 1 Power Connection Wire 1 Screw Kit for installation

More information

Pacific Antenna Two Tone Generator

Pacific Antenna Two Tone Generator Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination

More information

DirectCommand Installation RoGator 864/874/1064/1074 (MY 2006 & Earlier) Ag Leader Technology

DirectCommand Installation RoGator 864/874/1064/1074 (MY 2006 & Earlier) Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100524 1 Generic Cable Installation Kit 2000901-1 1 Hardware Kit

More information

Part Number: Lt. Taupe / Stone Accessory Code: EH3

Part Number: Lt. Taupe / Stone Accessory Code: EH3 Part Number: Lt. Taupe - 00016-00710 / Stone- 00016-00720 Accessory Code: EH3 Kit Contents Item # Quantity Reqd. Description 1 2 Headrest Assembly 2 2 Remote Control 3 2 Cables 3 4 1 Power Cord #9 5 1

More information

Installation Instructions

Installation Instructions Installation Instructions Page 1 of 18 November 2007 Communication, Hands-Free Version 6.0 Accessory Development These Installation Instructions supersede all previous versions. SUBJECT PHONE DOCKING CRADLE

More information

PeopleNet Video Intelligence. Generation 1 & 2 Side Cameras. Installation Guide

PeopleNet Video Intelligence. Generation 1 & 2 Side Cameras. Installation Guide PeopleNet Video Intelligence Generation 1 & 2 Side Cameras Installation Guide Rev. 4/13/18 (Gen-2 MirrorCam kit) 1 P a g e Contents Before You Begin... 3 General Principles to Guide the Mounting Process...

More information

Multitronic. Technical data

Multitronic. Technical data Multitronic EMC Aluminium enclosure system for MCR technology Integrated guide grooves for PCB s External mounting slots with spring nuts Technical data Material: DIN EN 573 EN AW-AlMgSi Ingress protection:

More information

APPLICATION SPECIFICATION. 1 of 22 B Millipacs HM 5 and 8 Row Right Angle Signal Receptacles Millipacs HM Right Angle Headers

APPLICATION SPECIFICATION. 1 of 22 B Millipacs HM 5 and 8 Row Right Angle Signal Receptacles Millipacs HM Right Angle Headers 1 of 22 B Millipacs HM 5 & 8 Row Receptacle & Right Angle Header Application Specification MPACS 5R RA RCP MPACS 8R RA RCP MPACS 5R RA HDR TABLE OF CONTENTS 2 of 22 B 1. OBJECTIVE...3 2. SCOPE...3 3. GENERAL...3

More information

DirectCommand Installation Hardi Spray Box II 39-pin Kit. Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 16

DirectCommand Installation Hardi Spray Box II 39-pin Kit. Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 16 DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100532 1 Cable Installation

More information

Cab Box Kit Dome Plug Cab Box Cab Box Lid

Cab Box Kit Dome Plug Cab Box Cab Box Lid DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100578 1 Cable Installation

More information

Connectivity Products

Connectivity Products Cable Glands Strain Relief Snap-In Labels Lock Nuts Torque Wrench Protective Sleeves U2 U5 U5 U6 U7 U8 Features NPT and PG thread cable glands in nylon or metal materials Locknuts in multiple thread sizes

More information

SmartWitness KP1S + SVC400

SmartWitness KP1S + SVC400 SmartWitness KP1S + SVC400 Installation Guide v.1.2 + WARNING: SmartWitness installations should be performed by a qualified individual or installation professional only. Working with a vehicle's power

More information

B&W RearView Camera Installation & Operation

B&W RearView Camera Installation & Operation B&W RearView Camera Installation & Operation CA52 (Camera) FOR MORE INFORMATION WWW.STRATEGICVISTA.COM BEFORE OPERATING THIS SYSTEM, PLEASE READ THIS MANUAL THOROUGHLY AND RETAIN IT FOR FUTURE REFERENCE

More information

Upgrading a 2U CHP to an i7 Quad Core SBC

Upgrading a 2U CHP to an i7 Quad Core SBC Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10

More information