winline surface linear 309W wet

Transcription

1 Project: winline surface linear 39W wet Qty: Type: Winline Surface Linear Wet - WSL39W series Linear Center Balance - LCB Linear Longest Possible - LLP Linear Same - LSL linear plan 3ADJ 3FMC Run offered in 6" increments starting at " ex. FT6 = FT 6IN See page for maximum run lengths run length The Winline WSL39W is a high performance linear LED luminaire suitable for the illumination and grazing of exterior walls, ceilings, and other planes. Robust in construction for ultimate durability, the housing is extruded aluminum, the adjustable mounts and end caps are die-cast, and the fixed mounts and all screws are stainless steel. The UV stable acrylic lens provides even beam control. Beam Spreads: The 3 Series is available in beam spreads of, 3, and. See page 6 for photometric data. Color & Light Output: The 3 Series utilizes Nichia 77 white LEDs in four standard color temperatures. Model WSL39W features () LEDs/ft. 3 Series Model WSL39W Color Temperature lm/ft W/ft ANSI-K White ANSI-3K White ANSI-3K White 9.9 ANSI-K White 9.9 Results based test ISF3 beam spread Note: LM79 Tests- see page 6 ft section length - MSL ft 6in section length - MSL/6 ft section length - MSL ft 6in section length - MSL/6 3ft section length - MSL3 3ft 6in section length - MSL3/6 ft section length - MSL adjustable mount (3 series) - 3ADJ fixed mount (3 series) - 3FMC degrees - DEG 3 degrees - 3DEG degrees - DEG degrees - DEG LED Linear 7 - LLP7A maximum section length mounting accessory distribution source : Winline WSL39W power consumption is 9.9W/ft. The Winline 3 series operates on VAC using magnetic transformers. A wide range of remote transformers are available in V and 77V primary. Dimming: Used with remote mounted VAC magnetic transformers which can be dimmed with commonly available low voltage magnetic dimming equipment. Mounting & Adjusting: Available with both fixed and adjustable mounts. The adjustable mount provides over degrees of continuous rotation. can then be locked into place once desired position is established. See pages - for more mounting and adjustment information. Operating Temperature: Minimum and Maximum ambient air temperatures around this luminaire shall not exceed - F to F (-3 C to C). Any application of this product should also take into consideration air flow and ventilation to ensure performance and reliability. Kelvin - 7K 3 Kelvin - 3K 3 Kelvin - 3K Kelvin - K volt - Back to Back Feed ( 3ADJ ) - 3BBA Back to Back Feed ( 3FMC ) - 3BBF Right Feed ( 3ADJ ) - 3RAA Right Feed ( 3FMC ) - 3RAF Recessed Bottom Feed ( 3FMC ) - 3RBF Surface End Feed ( 3ADJ ) - 3SEA Surface End Feed ( 3FMC ) - 3SEF No Box Required or Ordered Separately - NOBOX color temperature voltage electrical option Weight: " -. lbs " lbs 8" - 3. lbs " - 7. lbs " -. lbs 8" - 8. lbs 3" -.3 lbs Warranty: -year limited warranty. Complete warranty terms located at Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at C. natural (type III) anodized aluminum - NAA semi gloss black paint - SGB semi gloss white paint - SGW custom paint finish - CPF Describe Modification: modified - MOD finish special Listing: Winline WSL39W is ETL listed for wet location. Complies with UL Standard 8 Winona Lighting 37 West Fourth Street Winona, MN

2 The Winline 3 Series is available in lengths up to 8", in 6" increments starting at ". end view 8".97mm 88" 7.7mm Nominal MSL MSL/6 MSL MSL/6 MSL3 MSL3/6 MSL model 39W Installed." 8.3"." 3.6".6" 97" 7.88" Fixed Mount (3FMC) 3.98mm 6.8mm 6.9mm 6.6mm 9.9mm 66.mm 6.mm s can be mounted as close as." min.(3.8mm). mounting end view fixed mount 93" 9.mm." 8mm 3SEF-SURFACE END FEED (only one required per run) fixed mount 3 fixed mount 7".mm fixed mount 3RBF-RECESSED BOTTOM FEED Only one required per run Use standard switch box (by others).7" 7.66mm.8" 7.9mm.6" 7.mm end view.3" 8.67mm 88" 7.7mm Nominal MSL MSL/6 MSL MSL/6 MSL3 MSL3/6 MSL Adjustable Mount (3ADJ) model 39W Installed 3.3" 9.".9" 3.86".8".67" 8.7" 333.mm 83.6mm mm 783.9mm 93.3mm 83.8mm 33.68mm The 3 Series Adjustable Mount allows for over of continuous rotation. can then be locked into place once the desired position is established. s can be mounted as close as." min.(3.8mm). end view adjustable mount." 3.3mm." 67mm 3SEA-SURFACE END FEED (only one required per run).".mm adjustable mount 3 adjustable mount adjustable mount Fixture aimed beyond vertical Fixture aimed beyond vertical.6" 67.6mm.6" 67.3mm.6" 67.6mm Peak Candela Peak Candela End View Fixture rotated to the right End View Fixture rotated to the left linear plan Linear Plan Winona offers the ability to provide a continuous run plan to suit your requirements by optionally offering three methods of configuration. LSL Linear Same : In this configuration each segment is the same length is standardized based on the longest length available and is the only option provided. Because it is dependent on one segment length there are mathematical limitations on what overall row lengths can be achieved. Example: FT row would be achieved with () FT long segments equaling FT (nominal). LCB Linear Center Balanced: This configuration incorporates the longest center segment(s) along with any additional lengths required to fill located at each end. Example: FT row would have () 3FT segments (one at each end) and () FT intermediate segments located in between. LLP Linear Longest Possible: In this plan the longest length available is optimized resulting in the fewest segments and mounting locations. Caution should be used where balanced appearance is a concern. Example: FT row would have () FT segments and () FT segment located at one end. LSL FT LCB FT LLP FT 3' 3' ' Winona Lighting 37 West Fourth Street Winona, MN

3 connection Fixed Mount (3FMC) * 3RAF- RIGHT ANGLE FEED 8".98mm Three styles of stainless steel conduit connection hubs are available for connections at ends, middle, or corners of runs..63" 66.mm 3BBF- BACK BACK FEED 88" 7.7mm * 3RAF- RIGHT ANGLE FEED 3.. 8".98mm 8".98mm * 3SEF- SURFACE END FEED 93" 9.mm 3BBF- BACK BACK FEED 3.. 8" 6.3mm 93" 9.mm.63" 66.mm * 3SEF- SURFACE END FEED. 3. 8".98mm 93" 9.mm 88" 7.7mm Winona Lighting 37 West Fourth Street Winona, MN

4 connection Adjustable Mount (3ADJ) * 3RAA- RIGHT ANGLE FEED.".6mm Three styles of stainless steel conduit connection hubs are available for connections at ends, middle, or corners of runs.." 6.39mm 3BBA- BACK BACK FEED.3" 8.93mm * 3SEA - SURFACE END FEED * 3RAA- RIGHT ANGLE FEED 3...".mm.".mm.9" 3.9mm 3BBA- BACK BACK FEED 3...3" 8.93mm.".mm.63" 66.mm.6".86mm * 3SEA- SURFACE END FEED.8".83mm. 3..3" 8.67mm." 3.3mm 88" 7.7mm Winona Lighting 37 West Fourth Street Winona, MN

5 power, dimming, and wiring The WINLINE 3 Series is to be powered by VAC only. Do not connect directly to line voltage under any circumstance. Connection to line voltage will permanently damage internal components and void manufacturer s warranty. VAC Transformer POWER REQUIREMENTS The WINLINE 3 series must be powered by a magnetic transformer. Do not use electronic transformers. Multiply run length by power consumption to calculate transformer wattage. run wattage should not exceed % of the transformer wattage. Model WSL39W Consumption 9.9 w/ft Maximum Run 3 ft s can be mounted as close as." min.(3.8mm) Dimming (if required) by others V or 77V MOUNTING AND WIRING 3FMC FIXED MOUNT DIMMING The WINLINE 3 Series is easily dimmed with Magnetic Low Voltage (MLV) Dimmers. Not all MLV dimmers are alike, even among the same manufacturer. Confirm with dimming equipment manufacturer that dimmer selected is designed to work with the transformer selected. 3 Locate end feed box, layout, and fasten the mount clips to mounting surface. 3ADJ ADJUSTABLE MOUNT. Trim luminaire feed wires as required but DO NOT REMOVE FUSE! 3. Connect luminaire wires to power feed wires with supplied connectors (as shown in connector detail below).. Bundle wires and secure inside bottom of housing with supplied wire clips.. Snap wire tray into housing bottom Snap fixture into the fixed mounts to secure. Locate endfeed box, layout and mark the mount locations.. Remove screws holding mount caps to mount bases and secure mounts to mounting surface with appropriate fasteners. 3. Lay feed wires over mounts from connection box through end of run.. Trim luminaire feed wires as required but DO NOT REMOVE FUSE!. Connect luminaire wires to power feed wires with supplied connectors (as shown in connector detail below). 6. Bundle wires and secure inside bottom of housing with supplied wire clips. 7. Snap wire tray into housing bottom. REMOTE MOUNTING CONSIDERATIONS The WINLINE 3 Series is powered from remote-mounted transformers. The maximum remote distance of the transformer is dependent on many factors including total LED load, wire size, distance from the transformer to the first fixture in each run, and starting voltage at the transformer. The installer is to ensure that VAC is present at the beginning of the run. By using a combination of large-gauge wire and adjusting the output voltage of the transformer, the installer can compensate for voltage drop over long remote distances. Use of # wire is recommended. CONNECTOR DETAIL -8GA. Wire (fixture wire) 8. Align boss on luminaire endcap into hole on mount cap 9. Install mount caps to mount bases.. Aim as required and lock in place with set screw at top of mount cap. -6GA. Female Push-On Terminal -GA. Male Push-On Terminal 3M EP3 Shrink Tube -GA. Piggy Back Push-On Terminal -GA. Wire (field wire) -GA. Wire (field wire) Winona Lighting 37 West Fourth Street Winona, MN

6 photometrics 3 Maximum Candela = Located At Horizontal = 67., Vertical =. # - Vertical Plane Through Horizontal s (-) # - Vertical Plane Through Horizontal s (9-) Maximum Candela = 7 Located At Horizontal =, Vertical = 7. # - Vertical Plane Through Horizontal s (-) # - Vertical Plane Through Horizontal s (9-) Maximum Candela = 6 Located At Horizontal = 7., Vertical =. # - Vertical Plane Through Horizontal s (-) # - Vertical Plane Through Horizontal s (9-) Maximum Candela = Located At Horizontal =, Vertical = # - Vertical Plane Through Horizontal s (-) # - Vertical Plane Through Horizontal s (9-) IES Test Report: ISF3 Catalog Number: WSL39W MSL DEG 3K Description: Nichia 77 LEDs / 8" Winline WSL39W Wet / 3K / Extruded Aluminum Housing / Acrylic Lens ANSI-binned K ANSI-binned 3K ANSI-binned K IES Test Report: IST38 (PRORATED) Catalog Number: WSL39W MSL 3DEG 3K Description: Nichia 77 LEDs / 8" Winline WSL39W Wet / 3K / Extruded Aluminum Housing / Acrylic Lens ANSI-binned K ANSI-binned 3K ANSI-binned K Zone 3K IES Test Report: ISF37 (PRORATED) Catalog Number: WSL39W MSL DEG 3K Description: Nichia 77 LEDs / 8" Winline WSL39W Wet / 3K / Extruded Aluminum Housing / Acrylic Lens ANSI-binned K ANSI-binned 3K ANSI-binned K.97 6 Zone 3K IES Test Report: IST (PRORATED) Catalog Number: WSL39W MSL DEG 3K Description: Nichia 77 LEDs / 8" Winline WSL39W Wet / 3K / Extruded Aluminum Housing / Acrylic Lens Zone 3K Zone 3K ANSI-binned K ANSI-binned 3K ANSI-binned K Winona Lighting 37 West Fourth Street Winona, MN