ZAVIO Outdoor IR Mini Dome. Quick Installation Guide

Transcription

1 ZAVIO Outdoor IR Mini Dome Quick Installation Guide 0

2 Quick Installation Guide Please follow the installation steps below to set up your IP Camera. Check the package contents with the list below. See P.1 Physical overview. See P.2 I/O Terminal Block Circuit. See P.3 I/O Terminal Block Pin Definition. See P.3 LED Indicator Definition. See P.3 Power mode. See P.4 Installation of hardware and connection of all cables. See P.4 Windows: Go to Zavio website and download Camera Installation Tool. See P.9 Access the IP Camera using Camera Installation Tool. See P.10 MAC OS: using Safari Browser. See P.13 Lighting environment. See P.15 Change language of the web interface. See P.15 Application of IP Camera. See P.16 Package Contents Camera Quick Installation Guide Accessory IP Camera Brief product information and quick installation Alignment Sticker, L-type hex key wrench, Screw pack for wall and ceiling mounting, Plastic plate for wall and ceiling mounting, 2 pin terminal block DC connector, 6 pin cable for DI/DO and audio, Focus adjustment tool Software The following software and information are available online: - Video Management Software - Camera Installation Tool - User manuals - Camera Language Packs You may download the above at or you may scan the below QR-Code. To activate Video Management Software, please enter the license key below. 1

3 Physical overview Dome bubble Top cover Built-in Microphone Ethernet Socket DC 12V/1A External I/O connector Routing hole Lens Light Sensor MicroSD/SDHC/SDXC IR LEDs Internal microphone Reset Power LED Indicator Network LED Indicator 2

4 I/O Terminal Block Circuit I/O Terminal Block Pin Definition PIN Definition Description Max. V/A Black Ground - Brown + 12VDC 12V DC 1.2 W Red Audio In Connect the wires of the audio input device to GND - (Pin 1) and AUDIO.IN (Pin 3). Orange Audio Out Connect the wires of the audio output device to GND (Pin 1) and AUDIO.OUT (Pin 4). - Uses an NPN transistor with the emitter connected Yellow Digital Output 1 to the GND pin. If used with an external relay, a diode must be connected in parallel with the load 100 ma 24V for protection against voltage transients. Green Digital Connected to GND to activate, or leave floating (or Input 1 unconnected) to deactivate. 30V DC LED Indicator LED Color Indication Network Blue Solid blue when network is established. Blink blue when there is network activity. Red Solid red for booting up process Blue Solid blue for booting up completion Power Blink purple during: (a) firmware upgrade, (b) reset Purple button pressed for at least 5 sec to factory default. Unlit When reset button is pressed or when power off. 3

5 Power Mode PoE Mode Adaptor Mode Power Requirement PoE (IEEE802.3af) with Class 3 Power Consumption 4.19 W Power Requirement 12V/1A Adaptor Power Consumption 4.24 W Install the hardware and connect all cables A. Hardware installation 1) Loosen the tamper-proof screws using supplied L-type hex key wrench and remove the dome cover. Be careful not to scratch the dome cover. 2) You may feed the cables through the upper conduit hole or the side conduit hole. Please use the supplied blind pug to seal the unused conduit hole. 3) Side conduit hole installation: Disassemble the cable gland first and feed the network and I/O cable through the sealing nut, claw and cable gland. Connect the cables to the camera. Attach the cable gland to the conduit hole. Push the claw into the cable gland and tighten the sealing nut to secure the cables. B. Wall and ceiling mounting 1) Attach the alignment sticker to the wall/ceiling. Drill three holes into the wall - two for screws and one for cable. 2) Align the screw holes on the plastic base to the two plastic anchors on the wall/ceiling, insert the supplied screws to the hole and secure them. 3) Secure the camera to the plastic plate with the screws (M2.5x6 * 2pcs) 4

6 5

7 C. Wall mounting with L-type bracket (optional) 1) Drill two holes and hammer the supplied screw anchors on the desired installation location. 2) Align L-type bracket to the two plastic anchors on the wall/ceiling, insert the supplied screws to the corresponding hole and secure them. 3) Secure the plastic plate to the L-type bracket with screws (M4x10 * 2pcs) 4) Secure the camera to the plastic plate with screws(m2.5x6 * 2pcs) 6

8 D. Outdoor wall mount kit with L-type bracket (optional) 1) Drill two holes and hammer the supplied screw anchors on the desired installation location. 2) Align L-type bracket to the two plastic anchors on the wall/ceiling, insert the supplied screws to the corresponding hole and secure them. 3) Assemble the silicone rubber and outdoor kit together. 4) Put O-ring on the screws (M4x10); secure the outdoor kit to L-Type bracket. 5) Secure the camera to the plastic plate with screws(m2.5x6 * 2pcs) 6) Paste the waterproof-tape at microphone hole on the top cover. Conduit Conduit Note: Once waterproof sticker is pasted on top cover for outdoor used, microphone reception will be affected. 7

9 E. Connect all cables E1. Without Power over Ethernet (PoE) connection 1. Connect the power adaptor to the IP Camera. 2. Use a standard RJ-45 network cable and connect the IP Camera to a hub/switch/router. E2. Power over Ethernet (PoE) 1. Use a standard RJ-45 network cable and connect the IP Camera to a PoE-enabled hub/switch/router. F. To adjust the view angle- 3 axis mechanism design 1) Turn the lens module right and left to your desired pan position. 2) Turn the lens module up and down to your desired tilt position. 3) Turn the lens module to adjust the image orientation to satisfied angle. 8

10 Important: Make sure the IR LEDs are not blocked by the housing as it will affect the IR performance. If the image is upside down, please use the image rotate function in Video Setting. G. Completion Fix the tamper-proof screws using supplied special hex. Be careful do not scratch the cover glass. Clean the dome bubble to remove the dust and finger print. Windows: Go to Zavio Website and download Camera Installation Tool Please go download Camera Installation Tool. And follow the installation process to complete the installation. 9

11 Access the IP Camera using Camera Installation Tool 1. Please check two settings before using Camera Installation Tool. a. Browser s Internet Properties Secu rity Default Level b. Browser s Internet Properties Privacy Uncheck Pop-up Blocker 10

12 2. Click the Camera Installation Tool Icon on your desktop. The main page will show up listing all active camera and video server devices. Select the desired IP cameras from the list and click Link to IE. 3. Enter Username and Password to login to the IP Camera. (Default is admin / admin) 11

13 4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar: This website wants to install the following add-on: AxvideoView.cab from Zavio Inc. 5. Click the information bar, and select Install ActiveX control. 6. Click Install 12

14 7. Live video will display in the center of your web browser. MAC OS using Safari Browser 1. Select Safari Icon 2. Click Bonjour function and select the camera you wish to access. 13

15 3. Enter name and password to login to the IP camera (Default is admin / admin) 4. Live video will display in the center of your web browser. 14

16 Lighting environment setting Default setting for lighting environment is Auto. You may change exposure frequency to 50 or 60 Hz at Setting > Live View > Camera Setting > Image Setting. Change the Web Interface into your preferred language Before accessing the Setting page to change the language of the web interface, you must download the language pack. 1. Go to and download the language pack corresponding to your IP camera model. 2. Go to the IP camera setting page and upload the preferred language from the language pack downloaded from step 1. Setting > System > Maintenance > Language > Upload 3. Once the upload is complete, the browser will automatically change the language. 15

17 Application of IP Camera 16