INSTRUCTION MANUAL XX173-02

Size: px

Start display at page:

Download "INSTRUCTION MANUAL XX173-02"

Juliet Mae Taylor
6 years ago
Views:

1 INSTRUCTION MANUAL XX VC-600W, VC-600WS VC-610W, VC-610WS SERIES COLOR DOME CAMERAS About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. This installation should be made by a qualified service person and should conform to the National Electric Code, ANSI/NFPA 70 and

2 FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer s instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide reasonable protection against such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient the receiving antenna. Relocate the equipment with respect to the receiver.

3 Relocate the equipment away from the receiver. Plug the equipment into a different electrical outlet so that the equipment and receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: Interference Handbook, Bulletin CIB-2 This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, Mailstop SSOP, Washington, D.C , ISBN Warning : Power must be removed from this unit before removing circuit modules or cables. Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge. Take all necessary precautions to prevent static discharge.

4 CAMERA DIMENSIONS in. (mm)

5 PRECAUTIONS Do not open or modify Do not open the case except during maintenance and installation, as it may be dangerous and cause damage. Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or damages. Be careful when handling the unit To prevent damage, do not drop the camera or subject it to strong shock or vibration. Install away from electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may rise to high levels. Cleaning Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft detergent solution. Mounting Surface The mounting surface material must be strong enough to support the camera.

6 TROUBLESHOOTING Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. If no image appears Is the coaxial cable attached securely? Are the power and voltage normal? Has the iris of the lens inside the camera been adjusted correctly (with the level volume)? Is there adequate illumination? If the image is unclear Is the lens in focus? Is the lens dirty? Dirt or fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly?

7 SPECIFICATION VC-600W/VC-600WS GENERAL Spec NTSC PAL HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 550TV Lines 0.03fc, 0.3Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 48dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 1.0Vp-p/75ohm Composite Control DIP Switch BLC ME/AE ATW/AWB AGC DIP Switch Select ON/OFF DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) 12VDC -2.3W, 24VAC - 2.6W Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power)

8 SPECIFICATION VC-610W/VC-610WS GENERAL Spec NTSC PAL CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 480TV Lines 0.06fC, 0.6Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 45dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 1.0Vp-p/75ohm Composite Control DIP Switch ME/AE ATW/AWB WDR ON/OFF AGC MAX ON DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select WDR (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) 12VDC -3.9W, 24VAC - 4.0W Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power)

9 SPECIFICATION VC-600WDN/VC-600WDN-S GENERAL Spec NTSC PAL HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 550TV Lines 0.04fc, 0.4Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 48dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 10Vp-p/75ohm Composite Control DIP Switch BLC ME/AE ATW/AWB AGC DIP Switch Select ON/OFF DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) 12VDC -2.3W, 24VAC - 2.6W Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power)

10 SPECIFICATION VC-600WIR/VC-600WIR-S GENERAL Spec NTSC PAL HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 550TV Lines (BW, No LED) 0.04fc, 0.4Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 48dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 10Vp-p/75ohm Composite Control DIP Switch BLC ME/AE ATW/AWB AGC DIP Switch Select ON/OFF DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) MAX LED ON (12VDC - 4.6W, 24VAC - 4.7W) Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power)

11 LENS ADJUSTMENT AND CONNECTION LENS ADJUSTMENT VC-600W/VC-600WS, VC-610W/VC-610WS, VC-600WDN/VC-600WDN-S 1. Adjust the panning (360) and tilt (60) position. 2. Set the zoom position by using Zoom Lever Screw. 3. Set the focus by using Focus Lever Screw. 4. Loosen set screws to adjust roll (turns camera position top/bottom).

12 VC-600WIR/VC-600WIR-S 1. Adjust the panning (360) and tilt (51) position. 2. Set the zoom position by using Zoom Lever Screw. 3. Set the focus by using Focus Lever Screw. 4. Loosen set screws to adjust roll (turns camera position top/bottom).

13 CONNECTION CAUTION Check for polarity when using a 12VDC power supply. Input Voltage : 12VDC/24VAC CLASS 2 NOT WET, CLASS 3 WET

14 CAMERA SETTINGS VC-600W, VC-600WS

15 DIP Switch Functions (1) Compensating for backlight ON When backlight is too bright OFF Normal setting CAUTION : It will be correctly set by adjusting level volume 5. (2) Confirming the iris setting ME(ON) When DC autoiris lens installed AE(OFF) When fixed iris lens is installed (3) White balance setting ATW(ON) Use this under light source below 2500K and over 9500K of Natrium (Sodium) low color temperature light AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent lamp or incandescent light (4) Setting gain control (AGC) For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. ON Normal setting OFF Set this when there is excessive noise Second Video OUT Connector (Option) If installer is setting with portable monitor, this connector is used. Be sure to terminate the last video device at 75 ohms. IR LED Connector (Option) If extra IR LED board is attached, this connector is used.

16 Setting Monitor Synchronization (24 VAC adaptor users) The camera offers V-phase adjustment over 360. Vertical sync disturbance may occur when a switcher is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, adjust. CAUTION: When using the 12 VDC adaptor, sync setting is set to internal sync. Adjusting Level Volume If the entire image is too dark or bright, or the bakclight compensation is not correct even after is set to "ON", you need to adjust the level volume. CCW (LOW) Closes the lens iris, making the entire image darker CW (HIGH) Opens the lens iris, making the entire image brighter DC Varifocal Connector This should be used with DC IRIS LENS. Power connector Connect with AC/DC power, board attached inside. *Before making any adjustment, confirm that the cameras are connected to the power supply with the same polarity. To make an adjustment: While observing the video outputs from the cameras on an oscilloscope, press the first camera's V-phase pushbutton. Until vertical sync from all cameras are in phase. If the first camera's adjustment phase is insufficient, adjust the second camera's V-phase contol in the oppposite direction until they are in phase.

17 VC-610W, VC-610WS : WDR SETTING NO FUNCTION OFF DIP S/W ON 1 AE/ME AE ME 2 ATW/AWB AWB ATW 3 WDR OFF ON 4 AGC MAX OFF ON

18 DIP Switch Functions (1) Confirming the iris setting ME(ON) When DC autoiris lens installed AE(OFF) When fixed iris lens is installed (2) White balance setting ATW(ON) Use this under light source below 2500K and over 9500K of Natrium (Sodium) low color temperature light AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent lamp or incandescent light (3) WDR mode ON Wide dynamic function is working OFF Wide dynamic function is not working (4) Setting gain control (AGC) For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. ON Normal setting OFF Set this when there is excessive noise Second Video OUT Connector (Option) If installer is setting with portable monitor, this connector is used. Be sure to terminate the last video device at 75 ohms. IR LED Connector (Option) If extra IR LED board is attached, this connector is used.

19 Setting Monitor Synchronization (24 VAC adaptor users) The camera offers V-phase adjustment over 360. Vertical sync disturbance may occur when a switcher is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, adjust. CAUTION: When using the 12 VDC adaptor, sync setting is set to internal sync. Adjusting Level Volume If the entire image is too dark or bright, or the bakclight compensation is not correct even after is set to "ON", you need to adjust the level volume. CCW (LOW) Closes the lens iris, making the entire image darker CW (HIGH) Opens the lens iris, making the entire image brighter DC Varifocal Connector This should be used with DC IRIS LENS. Power connector Connect with AC/DC power, board attached inside. *Before making any adjustment, confirm that the cameras are connected to the power supply with the same polarity. To make an adjustment: While observing the video outputs from the cameras on an oscilloscope, press the first camera's V-phase pushbutton. Until vertical sync from all cameras are in phase. If the first camera's adjustment phase is insufficient, adjust the second camera's V-phase contol in the oppposite direction until they are in phase.

20 VC-600WDN, VC-600WDNS, VC-600WIR, VC-600WIRS : TDN/IR SETTING PORTABLE MONITOR DC VARIFOCAL

21 DIP Switch Functions (1) Compensating for backlight ON When backlight is too bright OFF Normal setting CAUTION : It will be correctly set by adjusting level volume 5. (2) Confirming the iris setting ME(ON) When DC autoiris lens installed AE(OFF) When fixed iris lens is installed (3) White balance setting ATW(ON) Use this under light source below 2500K and over 9500K of Natrium (Sodium) low color temperature light AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent lamp or incandescent light (4) Setting gain control (AGC) For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. ON Normal setting OFF Set this when there is excessive noise Second Video OUT Connector (Option) If installer is setting with portable monitor, this connector is used. Be sure to terminate the last video device at 75 ohms. IR LED Connector (Option) If extra IR LED board is attached, this connector is used.

22 Setting Monitor Synchronization (24 VAC adaptor users) The camera offers V-phase adjustment over 360. Vertical sync disturbance may occur when a switcher is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, adjust. CAUTION: When using the 12 VDC adaptor, sync setting is set to internal sync. Adjusting Level Volume If the entire image is too dark or bright, or the bakclight compensation is not correct even after is set to "ON", you need to adjust the level volume. CCW (LOW) Closes the lens iris, making the entire image darker CW (HIGH) Opens the lens iris, making the entire image brighter DC Varifocal Connector This should be used with DC IRIS LENS. Power connector Connect with AC/DC power, board attached inside. *Before making any adjustment, confirm that the cameras are connected to the power supply with the same polarity. To make an adjustment: While observing the video outputs from the cameras on an oscilloscope, press the first camera's V-phase pushbutton. Until vertical sync from all cameras are in phase. If the first camera's adjustment phase is insufficient, adjust the second camera's V-phase contol in the oppposite direction until they are in phase.

23 INSTALLATION camera's V-phase contol in the oppposite direction until they are in phase. VC-600W/VC600WS, VC-610W/VC-610WS, VC-600WDN/VC-600WDNS

24 VC-600WIR/VC-600WIR-S

25 1 Use the supplied hexagon wrench to remove the four fixing screws (B) securing the dome cover (A). 2 Make screw holes and a cable hole in the supplied gasket (D) that attaches to the back of the camera unit (C). 3 Attach the gasket (D) to the back of the camera unit (C). 4 Align the camera unit with the mounting surface; mark where the screw holes are to be drilled and then drill the four holes. 5 Cut a hole (diameter: 2.9 in. / 73mm) in the ceiling for routing the cables. 6 Pass the power cable (E) and video cable (F) from the camera unit through the cable hole in the ceiling. If mounting to a surface other than the ceiling, the cable can be routed through the hole in the side of the unit. 7 Align the four screw holes in the camera unit (C) with the screw holes in the installation surface, and then secure the camera in place by tightening the four or more screws (G). 8 Carry out the settings and adjustments for the camera. 9 If the dome liner (H) is secured in place, loosen the screw (I). Adjust the dome liner (H) so that the dome camera's lens is visible from the camera window. 10 Use a philips screwdriver to secure the dome cover (A) by tightening the screws (B). 11 When mounting outdoors on a wall, caulk the entire perimeter of the camera unit base with a uniform bead of silicon RTV adhesive or equivalent sealing compound. Note: The VC-600W/VC-610W series can be mounted in a pendant (suspended) configuration from a wall mount, a ceiling mount or from a 1/2- inch NPT pipe with the use of the VC-600W-PLATE adapter plate

26 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 1178,8 USA CCTV (2288) Fax: CCTV (2288) Germany vin-videotronic infosystems gmbh Lahnstrasse D Neumuenster Phone: +49 (0) Fax: +49 (0) European Headquarters Brunel Way Fareham, PO15 5TX, United Kingdom +44(0) Fax: +44(0) Far East Office Unit 5, 17/F, Metropole Square 2 On Yiu Street, Shatin New Territories,Hong Kong (852) Fax: (852) Internet Address: Vicon Part Number Rev 609 Copyright 2009, Vicon Industries Inc. Product specifications subject to change without notice.

INSTRUCTION MANUAL XX166-02

INSTRUCTION MANUAL XX166-02 VC-600 and VC-610 Series COLOR DOME CAMERAS About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.