INSTRUCTION MANUAL XX166-02

Size: px

Start display at page:

Download "INSTRUCTION MANUAL XX166-02"

Melvin Nelson
6 years ago
Views:

1 INSTRUCTION MANUAL XX VC-600 and VC-610 Series COLOR DOME CAMERAS About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. This installation should be made by a qualified service person and should conform to the National Electric Code, ANSI/NFPA 70 and all local codes. Installers should use appropriate hardware mounting materials. Dimensions : inch (mm) PRECAUTIONS Do not open or modify Do not open the case except during maintenance and installation, as it may be dangerous and cause damages. Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or damages. Be careful when handling the unit To prevent damage, do not drop the camera or subject it to strong shock or vibration. Install away from electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may rise to high levels. Cleaning Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft detergent solution. Mounting Surface The mounting surface material must be strong enough to support the camera.

2 TROUBLESHOOTING Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. If no image appears Is the coaxial cable attached securely? Are the power and voltage normal? Has the iris of the lens inside the camera been adjusted correctly (with the level volume)? Is there adequate illumination? If the image is unclear Is the lens in focus? Is the lens dirty? Dirt or fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly? WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. LENS ADJUSTMENT TILT - 60 Zoom Focus PAN Set Screw (2x) ROLL 1. Adjust the panning(360 ) and tilt(60 ) position. 2. Set the zoom position by using Zoom Lever Screw. 3. Set the focus by using Focus Lever Screw. 4. Loosen set screws to adjust roll (turns camera position top/bottom).

3 SPECIFICATION - VC-600, VC-600S GENERAL Spec NTSC PAL HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 550TV Lines 0.03fc, 0.3Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 48dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 1.0Vp-p/75ohm Composite Control DIP Switch BLC ME/AE ATW/AWB AGC DIP Switch Select ON/OFF DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) 12VDC -2.3W, 24VAC - 2.6W Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10 C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power) SPECIFICATION - VC-610, VC-610S GENERAL Spec NTSC PAL CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V) Scanning System 525 Lines 625 Lines Horizontal Resolution Sensitivity to Light [30IRE] Gamma Correction 480TV Lines 0.06fC, 0.6Lux(Scene) With F1.2 Lens 0.45 Shutter Speed 1/60-1/100,000[NTSC] 1/50-1/100,000[PAL] S/N Ratio Synchronization Video Output > 45dB [AGC off] Internal (12VDC) / External (Line Lock, 24VAC) 1.0Vp-p/75ohm Composite Control DIP Switch ME/AE ATW/AWB WDR ON/OFF AGC MAX ON DIP Switch Select ME/AE (ON/OFF) DIP Switch Select ATW/AWB (ON/OFF) DIP Switch Select WDR (ON/OFF) DIP Switch Select ON/OFF Electrical Spec Operating Voltage Power Consumption 12VDC(11-20V), 24VAC(20-27V) 12VDC -3.9W, 24VAC - 4.0W Mechanical Spec Operation Temp Air Humidity Lens Mount Connections via 14 F ~ 131 F ( -10 C ~ +55 C ) Up to max.90% mm BNC(VIDEO), 2P WIRE(Power)

4 CONNECTIONS AND CAMERA SETTINGS CONNECTIONS Red (+) Black (-) VIDEO DC12V AC24V CAUTION The use of a UL Listed Class 2 power supply is required to ensure compliance with electrical safety standards. Check for polarity when using a 12VDC power supply.

5 CAMERA SETTINGS FOR VC-600, VC-600S 6 DC VARIFOCAL ON OFF 2 PORTABLE MONITOR 5 DC LENS CONTROL 1 3 IR LED 4 LINE LOCK ADJUSTMENT 7 POWER CONNECTOR 1 DIP Switch Functions (1) Compensating for backlight ON When backlight is too bright OFF Normal setting CAUTION : It will be correctly set by adjusting level volume 5. (2) Confirming the iris setting ME(ON) When DC autoiris lens installed AE(OFF) When fixed iris lens is installed (3) White balance setting ATW(ON) Use this under light source below 2500K and over 9500K of Natrium (Sodium) low color temperature light AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent lamp or incandescent light (4) Setting gain control (AGC) For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. ON Normal setting OFF Set this when there is excessive noise 2 Second Video OUT Connector (Option) If installer is setting with portable monitor, this connector is used. Be sure to terminate the last video device at 75 ohms. 3 IR LED Connector (Option) If extra IR LED board is attached, this connector is used.

6 4 Setting Monitor Synchronization (24 VAC adaptor users) The camera offers V-phase adjustment over 360. Vertical sync disturbance may occur when a switcher is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, adjust 4*. CAUTION: When using the 12 VDC adaptor, sync setting is set to internal sync. 5 Adjusting Level Volume If the entire image is too dark or bright, or the bakclight compensation is not correct even after 1 is set to "ON", you need to adjust the level volume. CCW (LOWCloses the lens iris, making the entire image darker CW (HIGH)Opens the lens iris, making the entire image brighter 6 DC Varifocal Connector This should be used with 5 DC IRIS LENS. 7 Power connector Connect with AC/DC power, board attached inside. *Before making any adjustment, confirm that the cameras are connected to the power supply with the same polarity. To make an adjustment: While observing the video outputs from the cameras on an oscilloscope, press the first camera's V-phase pushbutton. Until vertical sync from all cameras are in phase. If the first camera's adjustment phase is insufficient, adjust the second camera's V-phase contol in the oppposite direction until they are in phase. CAMERA SETTINGS FOR VC-610, VC-610S 5 DC LENS CONTROL 4 LINE LOCK ADJUSTMENT 3 IR LED 6 DC VARIFOCAL 2 PORTABLE MONITOR 7 POWER CONNECTOR 1 DIP S/W NO FUNCTION OFF ON 1 AE/ME AE ME 2 ATW/AWB AWB ATW 3 WDR OFF ON 4 AGC MAX OFF ON

7 1 DIP Switch Functions (1) Confirming the iris setting ME(ON) When DC autoiris lens installed AE(OFF) When fixed iris lens is installed (2) White balance setting ATW(ON) Use this under light source below 2500K and over 9500K of Natrium (Sodium) low color temperature light AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent lamp or incandescent light (3) WDR mode ON Wide dynamic function is working OFF Wide dynamic function is not working (4) Setting gain control (AGC) For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. ON Normal setting OFF Set this when there is excessive noise 2 Second Video OUT Connector (Option) If installer is setting with portable monitor, this connector is used. Be sure to terminate the last video device at 75 ohms. 3 IR LED Connector (Option) If extra IR LED board is attached, this connector is used. 4 Setting Monitor Synchronization (24 VAC adaptor users) The camera offers V-phase adjustment over 360. Vertical sync disturbance may occur when a switcher is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, adjust 4*. CAUTION: When using the 12 VDC adaptor, sync setting is set to internal sync. 5 Adjusting Level Volume If the entire image is too dark or bright, or the bakclight compensation is not correct even after 1 is set to "ON", you need to adjust the level volume. CCW (LOWCloses the lens iris, making the entire image darker CW (HIGH)Opens the lens iris, making the entire image brighter 6 DC Varifocal Connector This should be used with 5 DC IRIS LENS. 7 Power connector Connect with AC/DC power, board attached inside.

8 *Before making any adjustment, confirm that the cameras are connected to the power supply with the same polarity. To make an adjustment: While observing the video outputs from the cameras on an oscilloscope, press the first camera's V-phase pushbutton. Until vertical sync from all cameras are in phase. If the first camera's adjustment phase is insufficient, adjust the second camera's V-phase contol in the oppposite direction until they are in phase. INSTALLATION I H G F D C B E A

9 The VC-600 and VC-610 can be either mounted to a surface (like a ceiling or wall) or installed into the ceiling, with or without an electrical box. 1 Use the philips screwdriver to remove the screw (C). 2 Separate upper case (A) from bottom case (D). 3 For surface mount installations, align the extension ring (G) with the mounting surface; mark the mounting screw holes and then drill the four holes. For in-ceiling installations not mounting to a 4x4 electrical box, mark the holes in the camera assembly (D) and then drill the holes. For in-ceiling installations, (G) is not used. 4 For in-ceiling installations, cut a hole (diameter: 2.9in./73mm) in the ceiling for outing the cables. 5 Route the power cable(s) and video cable(s) to the installation location. 6 Align the four screw holes in the extension ring (G) with the screw holes in the ceiling, and then secure by tightening four screws (F). Secure the camera assembly (D) in place with screws (F) supplied with the unit. For in-ceiling installations, align the holes in (D) with the holes drilled in the ceiling and secure the camera assembly with the hardware provided. If installing to an electrical box, secure (D) with the screws provided. 7 Pass the power cable (I) and video cable (H) from the camera unit through the cable hole in the ceiling. 8 Carry out the settings and adjustments to the camera. 9 Adjust the dome liner (E) so that the dome camera's lens is visible from the camera window and then use a philips screwdriver to attach the dome cover. 10 Connect upper case (A) and bottom case (D). 11 Tighten the screw (C). INSTALLATION WITH ADAPTER PLATE 1. Install Adapter Plate to existing electrical box in ceiling using screws. 2. Remove the extension ring from the housing. It is not needed for this installation. 3. Perform steps 2 and 5-11 from above procedure.

10 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York USA CCTV (2288) Fax: CCTV (2288) European Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44(0) Fax: +44(0) Germany vin-videotronic infosystems gmbh Lahnstrasse D Neumuenster Phone: +49 (0) Fax: +49 (0) Far East Office Unit 5, 17/F, Metropole Square 2 On Yiu Street, Shatin New Territories, Hong Kong (852) Fax: (852) Internet Address: Vicon Part Number Rev 408

INSTRUCTION MANUAL XX173-02

INSTRUCTION MANUAL XX173-02 VC-600W, VC-600WS VC-610W, VC-610WS SERIES COLOR DOME CAMERAS About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it