MultiVision Operating Instructions

Transcription

1 Innovation. Quality. Performance. Best in Industry. Worldwide. 1 MultiVision Operating Instructions MultiVision offers operators the option in completing various projects to use cameras for setting up fiducials, or reference marks for VisionTool software, to streamline repetitive cutting projects of similar material or design. The Vision menu offers several different options for operators to utilize their system for an improved output. MultiVision offers a few settings that must be set once and then are stored in the controller memory until those settings are overwritten. When customers purchase the MultiVision option, they will receive several hardware items to customize their machine: mounting bracket and slider, configured dongle for the licensing and software use, camera, attached camera lens, camera spotlight to help the operator focus light on the fiducial, and 50 Ethernet cable. Requirements * Testing: Test prints or examples of MultiVision job files should be available. See Appendix A: Creating Vision Job File in EnRoute. Dark laminate material that is approximately 6 square as well as white masking tape should be available. * Software: Suite 4 should be installed with version VisionTool.exe.

2 Innovation. Quality. Performance. Best in Industry. Worldwide. 2 Requirements Continued * Controller: Parameter 179 should be set to the following: for camera on a slider without an up sensor for camera on a slider with an up sensor with DCN for the camera not on a slider Parameter 138 & 139 need to be set to 1000 * Inits and Firmware: 2521 Controller Firmware: 4.46T or above Inits: or above Module: multivision4.uc v2.21 or above Note: Cameras on a slider also require either rio_multivision.uc or atcb_multivision.uc modules. K520 Controller Firmware: 4.46T or above Inits: or above Module: multivision4.uc v2.21 or above Note: Cameras on a slider also require either rio_multivision.uc or atcb_multivision.uc modules. HP4 Controller: Firmware: 4.46T or above Inits: or above Module: multivision4.uc v2.21 or above HP4 Driver 1.16 or above Note: Cameras on a slider also require either rio_multivision.uc or atcb_multivision.uc modules. LC520 Firmware: 4.46M or above Inits: or above Module: multivision4.uc v2.21 or above MD4 Driver 1.42 or above Note: Cameras on a slider also require either rio_multivision.uc or atcb_multivision.uc modules.

3 Innovation. Quality. Performance. Best in Industry. Worldwide. 3 Initial Ethernet Camera Setup It is highly recommended that you setup a simple static IP network between the MultiCam Controller Cabinet, the MultiVision Camera, and the Computer you wish to use for operations. See Example Below. Note: Once all initial setup of the camera is completed and operations verified, then you can add in network access in order to pull files from a server. See Example Below. In order to change the MultiVision Camera IP Setup to the new networks IP and Subnet mask, then repeat Vision Application Software Setup procedure.

4 Innovation. Quality. Performance. Best in Industry. Worldwide. 4 Suite 4 Connection Manager 1. Access Connection Manager by START>>PROGRAMS>>MultiCamS4>>Connection Manager. 2. Add connection to automatically search for the MultiCam controller. 3. Once control connection is found, the Test IP to verify communications. Vision Application Software Setup 1. Make sure the dongle is plugged in to computer that will communicate to the MultiVision Camera. 2. Verify or Copy the licensed file to C:\Windows directory. The directory will include the dongle serial number (e.g., 252) in the file name (e.g., ETC252.KEY).

5 Innovation. Quality. Performance. Best in Industry. Worldwide. 5 Note: Contact MultiCam Customer Service or MultiCam Tech Support if you do not have a key file for the dongle. 3. Create Shortcut to VisionTool4 Application. Open Windows Explorer and go to C:\Program Files\Machine Tools Suite 4.0 Select VisionTool4.exe. Copy and Paste Shortcut to the Desktop of Computer. 4. Open the VisionTool4 Application.

6 Innovation. Quality. Performance. Best in Industry. Worldwide Select View>>Settings>>Configure. The system will search for the IP address, and this process may take a few minutes. The IP address for the camera will appear at the top of the Configure Camera dialog.

7 Innovation. Quality. Performance. Best in Industry. Worldwide Highlight the camera on the top list and make sure the Upload Inspection box at the bottom is checked. 7. Select Set to finish the camera configuration. The inspection may take a few minutes to properly upload. 8. Close the window after the Configure dialog box at the bottom of the Configure Camera dialog shows that the Inspection has uploaded successfully. Fiducial Size Setup This process should be repeated any time fiducial print diameter changes. (e.g. from.25 to.375) or (e.g. 6.35mm to 8mm) 1. Verify and/or Change Fiducial Size. a. Press Menu to access the menu system. b. Press Jog Arrows until the blinking cursor is over the V in Vision. c. Press Enter to access the Vision sub-menu. d. Press Jog Arrows until the blinking cursor is over the F in Fiducial Diameter. e. Press Enter to access the Fiducial Diameter input screen. f. Key in the actual diameter of the fiducial dot that is on the print. Most cases this is 0.25 or 6.35mm. 2. Verify Fiducial Size changed in Vision Software Program.

8 Innovation. Quality. Performance. Best in Industry. Worldwide. 8 a. Click on View>>Settings and verify Fiducial Finding Method to fit a circle is the correct diameter of what was input at the keypad. Once the settings have been verified, then close out of Settings. Recalibrating the Lens Goal: To set the camera lens focus to exactly 1 inch field of view so that 1 inch equals 1000 pixels. Therefore, 1 pixel =.001 inches. 1. In Vision Tool Software, Select View>>Best Fit. 2. Make sure the Table Vacuum is on. The Table Vacuum should be left on for the remainder of the setup. 3. Click on Live Feed in the toolbar of VisionTool4. The camera status bar at the bottom should alternate between Capturing Frame and Frame Captured to show the camera is communicating properly with the host PC. 4. Jog the camera to the 1 FOV (25.4mm FOV) portion of the test material.

9 Innovation. Quality. Performance. Best in Industry. Worldwide Raise or lower the Z-axis until the camera shows the 1 FOV (25.4mm FOV). The lines need to at the far top and bottom of the computer screen with a sharp image quality. 6. Adjust the lens if necessary. a. Loosen the lens of the camera and hold the lens in place while focusing the camera. This will keep the lens from falling out of the camera and breaking. b. Raise or lower the Z-axis until the FOV image is sharp.

10 Innovation. Quality. Performance. Best in Industry. Worldwide. 10 c. Tighten the lens of the camera once that height has been reached. 7. Select View>>Normal Size for the remainder of the work. Focusing the Camera This process should be repeated each time the material thickness changes for standard machines and only after powering up for ATC machines. 1. Calibrate Tool #1 and leave it in the spindle for ATC machines. This tool should be the 1/4 End Mill. (Operators of manual spindles may begin at Step 2.) 2. Set the surface for manual machines and with Tool #1 for ATC machines. 3. Focus the camera. a. Press Menu to access the menu system. b. Press Jog Arrows until the blinking cursor is over the V in Vision.

11 Innovation. Quality. Performance. Best in Industry. Worldwide. 11 c. Press Enter to access the Vision sub-menu. d. Press Jog Arrows until the blinking cursor is over the F in Focus Camera. e. Press Enter to access the Focus Camera function. The ATC or knife-enabled system will prompt the operator to unload the tool. f. Press Enter to unload the tool or Cancel twice to leave the tool in the spindle. If Enter is chosen, the machine will unload the tool and return to the material. g. Press Jog Arrows to reach the fiducial on the material to be cut. h. Press Z-axis Jog Arrows to focus the camera on the fiducial. i. Press Enter when the fiducial is in focus. The keypad will return to the Vision sub-menu. Setting Camera Scale Goal: To set the cameras pixels in X and Y axis to an actual distance according to the FOV (Field of Vision). This is what makes a picture of a.25 dot actually measure out to be.25 inches. This process should be repeated any time fiducial print diameter changes. (e.g. from.25 to.375) or (e.g. 6.35mm to 8mm) 1. Press Jog Arrows until the blinking cursor is over the S in Set Camera Scale. The camera should still be focused on the fiducial from the Focusing the Camera function. 2. Press Enter to access the Set Camera Scale function. The keypad display will prompt the operator for a move size. The operator specifies a distance to which the machine will move, take a picture, move back, take a picture, calculate the scale, and save the camera scale.

12 Innovation. Quality. Performance. Best in Industry. Worldwide Enter a value of 0.2 or 6mm and follow Keypad prompts. The camera will complete a series of 0.2 (0.127 mm) moves off the fiducial point as the camera checks for pixels per inch (mm). The scale will be based on these readings. A typical scale value will be 1000 ± 100 for a 1 field of view. 4. Verify Settings of Keypad match settings in Vision Tool software. a. Select View>>Settings Capturing the Fiducial 1. Click on Live Feed in the toolbar of VisionTool4. The camera status bar at the bottom should alternate between Capturing Frame and Frame Captured to show the camera is communicating properly with the host PC. 2. Jog the camera over a fiducial. Operators may need to move the camera along the Z-axis to bring the fiducial into focus. 3. Click on Capture Fiducial in the toolbar. A box should appear around the fiducial as shown:

13 Innovation. Quality. Performance. Best in Industry. Worldwide. 13 Blue shows the ideal bounds. The blue box is equal to the input size of the fiducial diameter at keypad. Cyan Cross hairs box shows the actual bounds. At the bottom of the Vision screen will display the actual object size of what was captured. Assuming the dot is crisply printed, then the object size should be within +/ of input fiducial diameter. Problems Capturing the Fiducial 1. If the boxes do not appear around the fiducial and an error message appears at the bottom showing Fiducial Not Found, then operator should try Recalibrating the Lens, Fiducial Diameter, or Setting Scale procedure again.

14 Innovation. Quality. Performance. Best in Industry. Worldwide Object size not correct measurement. In the real world this dot does measure exactly.25 or 6.35mm. Therefore, the operator should try Recalibrating the Lens and/or Setting Scale procedure again. Setting Camera Offsets 1. Place a piece of white tape over a dark material, such as a dark laminate, to set the camera offset.

15 Innovation. Quality. Performance. Best in Industry. Worldwide Set the surface on the white tape using a 1/4 End Mill. 3. Set Home at the center of the tape. 4. Set the Cut Depth from the Params_2D menu to cut through the tape. Tape thicknesses may vary for each customer. a. Press Menu to access the menu system. b. Select Params_2D. c. Select Cut Depth. Enter the appropriate thickness using the number keypad (e.g., or 0.508mm). d. Exit Params_2D menu. 5. Set the Camera Offset. a. Press Menu to access the menu system. b. Press Jog Arrows until the blinking cursor is over the V in Vision. c. Press Enter to access the Vision sub-menu. d. Press Jog Arrows until the blinking cursor is over the S in Setting Camera Offsets. e. Press Enter to access Camera Offsets. The spindle will turn on, and the router will plunge to the Cut Depth. The controller will save the camera offsets in Flash parameters 132 (X-axis offset) and 133 (Y-axis offset). The camera offsets will be saved in the computer until overwritten or deleted by the operator and do not need to be reset for each job. Verifying and Fine Adjusting Camera Offsets 1. Insert.25 End mill into spindle.

16 Innovation. Quality. Performance. Best in Industry. Worldwide Surface Bit to top of material with vacuum table on. 3. Focus Camera from Vision Menu. 4. Jog bit over a fiducial a. Perfectly align the center of the bit to center of fiducial. 5. Set Soft Home. 6. Move to Cam Offsets. For this menu to work, the center line of the spindle must be at 0,0 over the fiducial before selecting menu item. a. Press Menu to access the menu system. b. Select Vision. c. Select Move to Cam Offsets. d. Press Enter The spindle will raise up and the camera will fire down. The machine will automatically move over to the X & Y camera offsets and take a snap shot of the fiducial. The keypad will then display how far off the captured fiducial is compared to it s offsets. 7. Follow Keypad prompts save fine adjustment values to the offset. Configuring the Auto Find Setting before Executing the Cut File

17 Innovation. Quality. Performance. Best in Industry. Worldwide Set the Auto Find Setting. a. Press Menu to access the menu system. b. Press Jog Arrows until the blinking cursor is over the V in Vision. c. Press Enter to access the Vision sub-menu. d. Press Jog Arrows until the blinking cursor is over the A in Auto Find Setting. e. Press Enter to access Auto Find Settings. f. Enter the distance for the camera to scan for the fiducial (e.g., 0.2 or mm) or leave as 0 so the operator may manually locate the second and third fiducials. 2. Execute the job file. See Appendix B: Fast Start, 11. DNC and 12. Start/Cancel/Pause. Vision Menu Options and Descriptions

18 Innovation. Quality. Performance. Best in Industry. Worldwide. 18 Set Parameter 179 allows the operator to enter the type of system at the initial setup. Operators may enter 100, 101, or 102 at the prompt based on the configuration of the camera. Parameter 179 should be set to the following: a. 100 camera on a slider without an up sensor b. 101 camera on a slider with an up sensor c. 102 camera not on a slider Focus Camera Sets a Z height value of the focused fiducial compared to the tools. If ATC machine, then the controller automatically readjusts the Z height value for the different calibrated tool lengths after each surface. Suggest Focus Camera after any new tool Calibration. If Standard machine, then must surface tool and focus the camera after each surface. Auto Find Setting specifies the distance that the system will scan for the fiducial before prompting the operator to Jog to the proper location if the fiducial is out of range. Manual Find Setting can be utilized once the Auto Find Setting has been disabled. Operators can enter 0 under Auto Find Setting before selecting Manual Find Setting and then select to Jog the tool to the fiducial or Jog the camera to the fiducial. Operators can press Enter once the tool bit or the camera is directly above the fiducial. Correlation Value This values works in conjunction with the Vision Tools displayed Match value after capturing a fiducial. The Match value are typically in the range of 0.2 to 0.3. Suggest setting correlation value slightly higher than the Match value. (e.g. 0.4) This function can be utilized if the material to be cut has a fuzzy or indistinct fiducial and the camera is unable to capture a clear image. If the correlation value is too low or too high, it will be rejected. Retake Distance allows the operator to improve the accuracy of the picture. The system will calculate how far away the fiducial is when a picture is taken. If that distance is greater than the retake distance, the camera will center the fiducial and take another picture. Operators should select a small distance (e.g., 0.002) to get the best results in the Fiducial Check function. Set Camera Scale is used to calibrate the camera scale. The operator specifies a distance to which the machine will move, take a picture, move back, take a picture, calculate the scale, and save the camera scale. The camera scale can be set at the initial setup and then will default to Set Camera Offsets allows the operator to set the camera offsets based on the center of the spindle and the center of the camera by drilling a hole with a Cut Depth entered in the Params 2D menu. The system prompts the operator to Jog over until the fiducial is close to the center of the PC screen. The location does not have to be exact. Settling Delay allows the operator to specify how long the system must wait before reading the fiducial. This is helpful in case the camera is shaking after slewing into position. Most systems work best with 20 ms. Fiducial Diameter allows the operator to inform the system as to the size of the fiducial when the system is searching. This diameter can be set up in either millimeters or inches. Move to Cam Offsets is mainly used as a verification tool to fine adjust the camera offset values.

19 Innovation. Quality. Performance. Best in Industry. Worldwide. 19 Fiducial Check allows the operator to determine how far out of square the machine is. Once the fiducials are found, the system calculates the X,Y Offset and Rotation values. Based on these values, the system can relocate the fiducials and display them in MotionMechanic, showing how far off the fiducials are in the X- and Y-axes. Once the fiducials are relocated, the display will prompt the operator about aborting the job. Connection Test will test the communication between the controller and the PC via the VisionTool4 or MultiVision and JobServer applications. Slider Test will test the slider to make sure it is working properly by moving the camera along the Z-axis. This menu item will only be available on machines with Parameter 179 set to 101.

20 Innovation. Quality. Performance. Best in Industry. Worldwide. 20 Appendix A: Creating Vision Job File in EnRoute 1. Create 3 round, filled fiducials as dark circles about 1/4 diameter on a white or light background on the Adobe Illustrator job file to be cut. (shown actual size) For colored or patterned backgrounds, operators should prepare a 3/4 white square with the fiducial in the center. 2. Position the fiducials in these approximate locations: a. First at or near 0,0 b. Second at or near 0,Y max c. Third at or near X max,0 Operator must have 3 fiducials per sheet. The placement of the fiducial does not need to be exact. Operator may have 3 fiducials per cut out image. 3. Import the job file in EnRoute. If importing Adobe Illustrator file, then strongly suggest saving file version down to V3.

21 Innovation. Quality. Performance. Best in Industry. Worldwide Rotate the image so that the ab side of the image is at the left or along the Y-axis. Not all images will need to be rotated, so the operator may skip this step if the image has a longer ab side than ac side. 5. Remove the detail on the inside of the images to show the die line only and select Automatic Cleanup (HPGL files excluded) to reduce the total number of contour points. This will provide MultiVision a smoother cut and better edge quality. 6. Create a tool entitled Vision by selecting Setup/Tool Library/Create a New Tool. 7. Select Drill or End Mill for the tool and select OK. 8. Select Save. No parameters need to be changed on this screen. Select Save for Tool Library changes and exit the screen.

22 Innovation. Quality. Performance. Best in Industry. Worldwide Whether ATC or Standard Machine, Operator will have to modify Enroute s MultiCam Driver to have 99 tools. Setup>>Machine Setup>>Tool Changer Assign the Vision Tool to location # Highlight all Fiducials and select Toolpath>>Drill>>Drill Centers. 11. Select Vision Tool, enter 0.1 as the depth, and select OK. Enroute requires a depth. No cutting parameters (e.g., Feedrate or Spindle Speed) need to be set at this time. 12. Highlight all the contours. 13. Select Toolpath/Routing Offset and select the appropriate tool (e.g., 1/4 End Mill). 14. Set cutting parameters and select OK.

23 Innovation. Quality. Performance. Best in Industry. Worldwide Select Machining/Order. The Vision Tool must be first. However, the order of the fiducials is not important. 16. Select Machining/Output to begin the cutting sequence. 17. Select File to name the document and save it in the DNC Files folder.

24 Innovation. Quality. Performance. Best in Industry. Worldwide. 24 Appendix B1: Fast Start MultiVision ATC Spindle 1. Turn on Power Locate the power switch, the round knob in the control enclosure, and rotate it to the ON position. Make sure that Suite 4 and VisionTool4 or MultiVision are installed on the computer Make sure the dongle is in place on the computer as the software will not run without the dongle. 2. Find Home Press Shift and Go Home to index the gantry, carriage, and Z assembly. Press Shift and Five to allow the machine to return any tools to the Tool Changer. 3. Calibrate New Tools Follow the Tool Calibration Procedure when calibrating new tools. MultiCam requires that tools be calibrated when a new tool is inserted into the tool holder. The machine will store the Z-axis tool length of the new tool in memory even after the machine is turned off. Only new tools need to be calibrated. 4. Turn on Table Vacuum Locate the power switch on the table vacuum. Switch the indicator to the ON position. The Table Vacuum must be on so that the surface can be set properly. Failure to turn on the vacuum will skew the configuration, which could affect the quality of the cutting sequence. 5. Set the Surface to the Top of the Material Use any calibrated tool. Place the grounding collar on the ATC mounting groove in the spindle tool holder. Press Set Surface. Place the surface block on top of the material underneath the tool. Press Z-axis Jog Arrows to lower the spindle until the bit is just above the surface block. The operator should monitor the Jog speed when lowering the Z-axis as the machine will only recognize the surface block when 0 is pressed. The spindle could crash into the material or the surface block and break the bit. Press and hold Zero to begin the surfacing routine. This will cause the Z-axis to move down slowly until the tool comes in contact with the surface block and then move up above the surface block to the Tool Lift Height. Remove the grounding collar and surface block before beginning work.

25 Innovation. Quality. Performance. Best in Industry. Worldwide Set Maximum Depth (as needed) Press Jog Arrows to position the tool over the spoilboard or sacrifice material. Place the grounding cradle on the ATC mounting groove in the spindle tool holder. Press Set Max Depth to set the maximum depth for the bit. Place the surface block underneath the tool and on top of the tabletop or at the required maximum depth. Press Z-axis Jog Arrows block. to lower the spindle until the end of the tool is just above the surface Press and hold Zero to begin the Maximum Depth routine. This will cause the Z-axis to move down slowly until the tool comes in contact with the surface block and then move up above the surface block to the Tool Lift Height. Remove the grounding collar and surface block before beginning work. 7. Adjust Maximum Depth (as needed) Press Shift and Set Max Depth. Press Cancel to clear the current maximum depth without having to reboot the machine or press Z-axis Jog Arrows to adjust maximum depth in one-thousandth increments (e.g., 0.001). A positive value will increase the range of maximum depth, and a negative value will decrease the range of maximum depth. Press Enter to accept or Cancel to abort. 8. Set Home Press Jog Arrows to place the center of the bit over the first fiduical. Press Set Home. Press Enter to accept the location. 9. Capture the Fiducial Click on Live Feed in the toolbar and Jog the camera over a fiducial. Operators may need to move the camera along the Z-axis to bring the fiducial into focus, and the spotlight will flash while the camera is in Live Feed mode. Click on Capture Fiducial in the toolbar. A box should appear around the fiducial.

26 Innovation. Quality. Performance. Best in Industry. Worldwide Focus the Camera after Powering Up the Machine Press Menu Press Jog Arrows to access the menu system. until the blinking cursor is over the V in Vision. Press Enter to access the Vision sub-menu. Press Jog Arrows until the blinking cursor is over the F in Focus Camera. Press Enter tool. to access the Focus Camera function. The system will prompt the operator to unload the Press Enter to unload the tool or Cancel to leave the tool in the spindle. Press Jog Arrows Press Z-axis Jog Arrows to reach the fiducial on the material to be cut. to focus the camera on the fiducial. Press Enter when the fiducial is in focus. The system will adjust to any changes in thickness, so operators do not need to refocus the camera before beginning the next job file. 11. Access a MultiVision Job File Press DNC and select the file. The VisionTool application will become active and the camera will Jog to the estimated location for the first fiducial. Watch the system Jog to the second fiducial once the camera locates the first fiducial. The value entered in Auto Find Setting will determine how far the camera will search for the second fiducial. Watch the system interpolate the exact location of the third fiducial and scan it. 12. Start / Cancel / Pause Press Start Press Cancel Press Pause to begin the cutting sequence. to abort the cutting sequence. to yield the cutting sequence.

27 Innovation. Quality. Performance. Best in Industry. Worldwide. 27 Appendix B2: Fast Start MultiVision Manual Spindle 1. Turn on Power Locate the power switch, the round knob in the control enclosure, and rotate it to the ON position. Make sure that Suite 4 and VisionTool4 or MultiVision are installed on the computer Make sure the dongle is in place on the computer as the software will not run without the dongle. 2. Find Home Press Shift and Go Home to index the gantry, carriage, and Z assembly. The activation of this function enables the operator to access the spindle inverter. 3. Insert Cutter Insert the tool into the collet. Twist the tool to lock it into place. 4. Turn on Table Vacuum Locate the power switch on the table vacuum. Switch the indicator to the ON position. The Table Vacuum must be on so that the surface and maximum depth can be set properly. Failure to turn on the vacuum will skew the configuration, which could affect the quality of the cutting sequence. 5. Set the Surface to the Top of the Material Use any calibrated tool. Place the grounding collar on the ATC mounting groove in the spindle tool holder. Press Set Surface. Place the surface block on top of the material underneath the tool. Press Z-axis Jog Arrows to lower the spindle until the bit is just above the surface block. The operator should monitor the Jog speed when lowering the Z-axis as the machine will only recognize the surface block when 0 is pressed. The spindle could crash into the material or the surface block and break the bit. Press and hold Zero to begin the surfacing routine. This will cause the Z-axis to move down slowly until the tool comes in contact with the surface block and then move up above the surface block to the Tool Lift Height. Remove the grounding collar and surface block before beginning work.

28 Innovation. Quality. Performance. Best in Industry. Worldwide Set Maximum Depth (as needed) Press Jog Arrows to position the tool over the spoilboard or sacrifice material. Place the grounding cradle on the ATC mounting groove in the spindle tool holder. Press Set Max Depth to set the maximum depth for the bit. Place the surface block underneath the tool and on top of the tabletop or at the required maximum depth. Press Z-axis Jog Arrows block. to lower the spindle until the end of the tool is just above the surface Press and hold Zero to begin the Maximum Depth routine. This will cause the Z-axis to move down slowly until the tool comes in contact with the surface block and then move up above the surface block to the Tool Lift Height. Remove the grounding collar and surface block before beginning work. 7. Adjust Maximum Depth (as needed) Press Shift and Set Max Depth. Press Cancel to clear the current maximum depth without having to reboot the machine or press Z-axis Jog Arrows to adjust maximum depth in one-thousandth increments (e.g., 0.001). A positive value will increase the range of maximum depth, and a negative value will decrease the range of maximum depth. Press Enter to accept or Cancel to abort. 8. Set Home Press Jog Arrows to place the center of the bit over the first fiduical. Press Set Home. Press Enter to accept the location. 9. Capture the Fiducial Click on Live Feed in the toolbar and Jog the camera over a fiducial. Operators may need to move the camera along the Z-axis to bring the fiducial into focus, and the spotlight will flash while the camera is in Live Feed mode. Click on Capture Fiducial in the toolbar. A box should appear around the fiducial.

29 Innovation. Quality. Performance. Best in Industry. Worldwide Focus the Camera Each Time the Material Thickness Changes Press Menu Press Jog Arrows to access the menu system. until the blinking cursor is over the V in Vision. Press Enter to access the Vision sub-menu. Press Jog Arrows until the blinking cursor is over the F in Focus Camera. Press Enter tool. to access the Focus Camera function. The system will prompt the operator to unload the Press Enter to unload the tool or Cancel to leave the tool in the spindle. Press Jog Arrows Press Z-axis Jog Arrows to reach the fiducial on the material to be cut. to focus the camera on the fiducial. Press Enter when the fiducial is in focus. 11. Access a MultiVision Job File Press DNC and select the file. The VisionTool application will become active and the camera will Jog to the estimated location for the first fiducial. Watch the system Jog to the second fiducial once the camera locates the first fiducial. The value entered in Auto Find Setting will determine how far the camera will search for the second fiducial. Watch the system interpolate the exact location of the third fiducial and scan it. 12. Start / Cancel / Pause Press Start Press Cancel Press Pause to begin the cutting sequence. to abort the cutting sequence. to yield the cutting sequence.