OPERATING MANUAL. Hyper Dynamic Range

Transcription

1 OPERATING MANUAL Before attempting to connect or operate this product, please read these instructions completely Hyper Dynamic Range WDS-HDR1527DN Day & Night OLPF Removable WDS-HDR1520 DIGITAL COLOR VIDEO CAMERA ON-SCREEN-DISPLAY, HIGH RESOLUTION, AC24V / 12VDC WARNING: TO REDUCETHE RISK OF FIRE OR ELECTRONIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT REMOVE COVER OR BACK. CAUTION: 1. CONNECT 24VAC UL LISTED CLASS 2 POWER SUPPLY. 2. INSTALL CAMERA UNDER UNSTABLE LIGHT SOURCE MAY CAUSE ABNORMAL FUNCTION. 3. ONLY USE CAMERA UNDER CONDITIONS WHERE TWMPERATURES ARE BETWEEN -10 C to 50 C. FIELS INSTALLATION MARKING: INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES -1 -

2 1. General This a color CCD video camera employs a 1/3 inch charge coupled device solid-state imaging device with 470/410 k or 310/270 k picture elements, This unit is equipped with a newly developed DSP (Digital Signal Processor) for processing the video signal. This camera has dynamic range 400: 1, surveillance under various critical backlighting environments are always possible, The camera uses Sony new double speed CCD. It s dynamic range allows processing over 52dB. 2. Features 1/3 SONY Wide Dynamic Double Speed CCD, Super HAD with 470K / 410K (PAL / NTSC) pixels, 10bit A/D Digital Signal Process (DSP) Hyper Dynamic Range 400:1 Highest Dynamic Range up to 52dB and real time video output 30 fps 6 Preset modes and 1 Customized mode setting are available for various environments. For subject requiring special protection due to privacy concerns, 8 masks can be show on the screen by using OSD Control Electronic Frame Integration from 2x ~ 160x sense up Advanced On Screen Display (OSD) control Versatile exposure system WD mode, Flick-less, Normal auto iris Outstanding signal to noise ratio better than 50dB IR accuracy: Vivid color performance in the day time and sharp B&W image with no focus shift in the nighttime. Smart Optical Low Pass Filter (O.L.P.F.) switching mechanism allows changing between color and monochrome. Enhanced (O.L.P.F.) control system (4 modes) Automatic Manual Schedule External 1/O Integration GPIO (day/ night, IR projector control) On Screen Display control (OSD) Remote control by RS232C Internal or Line-lock external Sync Isolated switching power DC12V /AC24V, AC85 ~ 265 V -2 -

3 3. Name of Parts and Functions A J K L I F B DC12V/AC24 MODEL G E C H D A. C (CS) mount adapter if a CS mount lens is to be used, remove the C mount ring B. Holder screw hole Standard photographic pan-head screw size (1/4 20) Flange focal lock screw C. Flange focal lock screw Thumbwheel locking screw and provided screwdriver Back focus thumbwheel D. Flange focal distance adjuster adjust this ring when back focus adjustment is needed. -3 -

4 E. Auto iris lens connector (MINI JACK) Use with accompanying auto iris lens control connector plug. Auto iris lens has built-in EE amp. (VIDEO Type) Set the lens selector to VD position. Connector cable leads 1.Red --- power 3.White --- video 2.NC 4.Black --- shielded Auto iris lens without EE amp. (DC Type) Set the lens selector to DD position. Connector cable leads 1. Damping coil (-) 3. Driving coil (+) 2. Damping coil (+) 4. Driving coil (-) F. Video output terminal (BNC) This connector is used to connect with VIDEO IN connector of monitor. G. On-Screen Display keypad H. Slide out for control panel I. Power pilot LED J. DC12V / AC 24V Block Terminal This terminal accepts DC 12V (Non-polarity) or AC 24V. The other model: AC 85 ~ 265V. DC12V/AC24 MODEL K. OSD Remote control connector (MINI JACK) L. The Device for sensing brightness level (for D/N function). L. Only Applicavle for WDS-HDR 1527DN 4. USER OSD SETTING SETTING SWITCHES AND FUNCTIONS 1.UP button-this button is used to move the cursor upwards. Use this button to select item. 2.LEFT button This button is used to move the cursor left. Use to select or adjust the parameters of the selected item. 3.RIGHT button-this button is used to move the cursor to the right. Use to select or adjust the parameters of the selected item. 4.DOWN button-this button is used to move the cursor downwards. Use this button to select item. -4 -

5 5.ENTER button-press this button to display the setting menu, if the selected item has its own menu; press this button to enter sub menu. PC control For window 95/98/ME/2000/XP 1. Insert the floppy into diskette drive 2. Execute OSD_CONT.EXE 3. A keypad icon will be displayed on screen 4. Use mouse to point the icon for on-screen-display setting. RS-232 Connection Please refer to the Setup option In the program window (com2 default) 1.RX pin----sd (D-sub 9) pin 3 from PC 2.TX pin----rd (D-sub 9) pin 2 from PC 3.NC 4.GND------GND (D-sub9) pin 5 1/O port The port can send or received signal by external device. Select option mode by OSD D/N function The camera can switch day or night by external device when it select External mode. And other mode can send signal to external device. Day (ov0, Night (+5) Only applicable for WDS-HDR1527DN 5. SETTING MENU AND FUNCTIONS CAMERA ID SENSE UP LIGHT CNTL WHITE BAL PICTURE FOCUS ADJ MISC SETUP MENU WD MODE ATW VIDEO 1. Press the ENTER key to enter main menu. 2. Press UP/DOWN key to select the item for -5 - adjustments. 3. Press ENTER key to enter the sub menu of selected item. 4. Move cursor to END at the bottom of the screen END INIT UNLOCK and press the ENTER to close the setup menu and return to normal camera operation mode. 5. Move cursor to INIT and press ENTER to return all parameters to the factory default settings. (Don t press INIT unless it is necessary) 6. Move cursor to position and press ENTER key for menu position setting.

6 7. Move the cursor to UNLOCK and press the ENTER to LOCK the setup menu. Note: If no button is pressed for 2 minutes while any setting menu displayed, all modified UNLOCK PASSWORD Press UP, DOWN, DOWN, RIGHT then ENTER key to unlock the menu. data will be stored and camera will return to the normal camera picture mode. 6. Setting Procedure 6.1 Camera Identification Setting (CAMERA ID) Move cursor to CAMERA ID then press ENTER key to enter ID sub menu Blinking CAMERA ID : A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z,. RET POSI Character Area Editing Data Area Command area Move cursor to the character you wish to enter or modify by pressing UP, DOWN, RIGHT, LEFT key. After selecting the character, by press ENTER key, selected character will display on editing data area. Repeat the step above until all characters are inputted or edited. Move cursor to to edit a specific character in editing data area. Move the cursor to BLANK (between z and, ) character position then press enter to erase the character previously entered. Move cursor to POSI, then press ENTER, the camera ID will be displayed on screen. Camera ID can be moved to desired position by CAM 001 pressing UP, DOWN, RIGHT, LEFT key, then press ENTER to fix the ID position and return to previous menu. -6 -

7 6.2 Sense UPMove cursor to SENSE UP, Press LEFT T or RIGH key to select item, Mode sequence: SETUP MENU CAMERA ID 2X 4X 8X 16X SENSE UP LIGHT CNTL WHITE BAL WD MODE ATW X 40X 20X PICTURE VIDEO The maximum sense up function for low bright, MISC It controls and offers the optimal brightness level by END INIT UNLOCK increasing the number of stored fields of the CCD in response to the brightness level. This function will start up and control electronic frame integration automatically. 6.3 Light Control Move cursor to LIGHT CNTL then press ENTER key to enter sub menu SETUP MENU CAMERA ID SENSE UP LIGHT CNTL WD MODE WHITE BAL ATW PICTURE VIDEO MISC Press ENTER to sub menu WD MENU MODE INDOOR1 FLICKERLESS END INIT UNLOCK Press RIGHT or LEFT key to select item, then press ENTER to enter Item sub menu Mode sequence: WD MODE NORMAL WD mode setting Press LEFT or RIGHT key to select item Mode sequence: INDOOR1 INDOOR2 INDOOR3 INDOOR4 ENGINEER OUTDOOR2 OUTDOOR1 The WD mode has 6 options: INDOOR1: Lobby or similar environments INDOOR2: Hallway or similar environments INDOOR3~4: Environments with large contrast OUTDOOR1: Camera near to the door surveillance for outside or similar environments -7 -

8 OUTDOOR2: Camera under strong light condition shooting to weak light environments ENGINEER: This function is open for Engineer only FLICKERLESS (NTSC system only, PAL system off): When the function is set to ON, the shutter speed 1/60 sec will become 1/100 sec to Flickerless. (NTSC system) NORMAL mode setting Move cursor to LIGHT CNTL and choose NORMAL then press ENTER key to enter NORNAL mode sub menu NORMAL mode sub menu TYPE Move cursor to TYPE and press LEFT or RIGHT to change Auto Exposure TYPE Mode sequence: AES AUTO IRIS ME Shutter speed of each mode: AES mode: 1/50(1/60) to 1/100,000 sec. AUTO IRIS mode: 1/50(1/60) sec ME mode: 1/50(1/60) to 1/100,00 sec AUTO IRIS mode sub menu Press ENTER key, AUTO IRIS menu will be displayed on screen. Move cursor by UP/DOWN key to select adjustment item. CAMERA ID SENSE UP SETUP MENU LIGHT CNTL WHITE BAL PICTURE MISC NORMAL ATW VIDEO END INIT UNLOCK NORMAL MENU TYPE AES BLC AGC 00 E-ZOOM AUTO IRIS MENU IRIS LEVEL 05 FLICKLESS IRIS LEVEL: Press LEFT or RIGHT to adjust the level for auto-iris Lens (for DC type). Ranging from 0 to 10. FLICKERLESS (NTSC system only, PAL system off): When function is set to ON, the shutter speed 1/60 sec will become 1/100 sec to Flickerless. (NTSC system) ME MENU SHUTSPEED 1/50SEC GAIN

9 ME mode sub menu Press ENTER key to NORMAL menu, MANUAL EXPOSURE menu will be displayed on screen. Move cursor by UP/DOWN key to select adjustment item. PUSH TO LOCK MENU PTL PUSH SHUTTER SPEED: 1/60(1/50), 1/120(1/100), 1/250, 1/500, 1/1,000, 1/2,000, 1/5,000, 1/10,000 sec. Gain: You can increase or decrease the bright level. BLC: Press LEFT or RIGHT key to turn Back Light Compensation function ON/ AGC: You can increase or decrease the bright level low light condition. E-ZOOM Press ENTER key to display E-ZOOM sub menu. NORMAL MENU TYPE AES BLC AGC 00 FLICKERSS E-ZOOM E-ZOOM sub menu Press LEFT or RIGHT key to change 3 type E-ZOOM, press ENTER key back to previous menu. E-ZOOM WHITE BALANCE SETUP MENU Move cursor to WHITE BAL then press ENTER key to enter CAMERA ID sub menu Item sequence: ATW PRESET MANUAL PTL Push To Lock ATW SENSE UP LIGHT CNTL NORMAL WHITE BAL ATW PICTURE VIDEO MISC END INIT UNLOCK PRESET MENU WB FIX INDOOR 3200K -9 -

10 1. ATW Auto tracking white balance 2. Preset fixed color temperature for Indoor Outdoor Fluorescent Indoor 3. PTL Push to lock white balance Press ENTER key the camera will process white balance. Character PTL PUSH will then change to PTL SETTING, during the process. Please wait until the Character change back to PTL PUSH to exit this menu. MENU WHITE BAL MENU R GAIN 15 B GAIN Manual manual white balance Change the value of R or B gain, to adjust desired white balance 6.5 PICTURE CONTROL Menu item: VIDEO GAMMA APERTURE VIDEO VIDEO MENU 1. Brightness level setting Move cursor to BRIGHT position, while observing the color video monitor or waveform monitor / oscilloscope, press LEFT or RIGHT key to adjust the brightness level. VIDEO MENU BRIGHT 07 PEDESTAL 1.0 IRE 2. Pedestal level setting Move cursor to PESESTAL position, while observing the color video monitor or waveform monitor / oscilloscope, press LEFT or RIGHT key to adjust the pedestal level. APERTURE MENU Press LEFT or RIGHT key to adjust aperture correction. GAMMA MENU 1.There are 7-gamma curves, press LEFT or RIGHT key to adjust gamma correction. APERTURE MENU APERTURE 01 GAMMA MENU Y GAMMA

11 6.6 Day /Night Control only applicable for WDS-HDR1527DN Move Cursor to D/N CNTL then press ENTER key to enter D/N MENU CAMERA SENSE UP SETUP MENU LIGHT CNTL WHITE BAL PICTURE D/N CNTL FOCUS ADJ MISC NORMAL ATW VIDEO END INIT UNLOCK Press RIGHT to LEFT key to select item, then Press the ENTER to enter Item sub menu Lux/Delay SCHEDULE EXTERNAL DAY MODE NIGHT MODE ENGINEER ENTER D/N MENU D/N TYPE D N Mode LUX/DELAY Normal D/N Type 1. LUX/ DELAY MENU Press RIGHT or LEFT key to set the item. LUX LEVEL- Sets the color to mono- Chrome switching level. You can select LOW LVL, MID LVL, HI LVL. LUX/ DELAY MUNE LUX LEVEL LOW DELAY TIME 10 SEC DELAY TIME- Sets the detecting time. The color/ monochrome mode switches If the brightness level change specified. You can select 10 sec, 30sec or 60sec 2. SCHEDULE (D.N SWITCH TIME) LUX/ DELAY MUNE This function can set the time to change LUX LEVEL LOW the Day/ Night mode. DELAY TIME 10 SEC CHOICE D/N TYPE: Press ENTER key to Switch D or N mode to conform to your setting Time. If N D time same with other camera will plus 1 minute by itself. 3. EXTERNAL This function allow use external device to Control camera switch to Night mode by HI(+5V) potential or LOW (0V) potential. Function 1~3 will action when back to first menu (SETUP MENU) EXTERNAL D N MENU INPUT SIGNAL HI RETURE -11 -

12 4. DAY MODE Switch to DAY mode. 5. NIGHT MODE Switch to NIGHT mode. 6. ENGINEER MODE This mode for engineer only D N MODE This item will switch to WD mode or Normal Mode when Night Mode. Only applicable for WDS-HDR1527 DN 6.7 FOCUS ADJ Move cursor to FOCUS ADJ then press ENTER key to enter FOCUS ADJ MENU SETUP MENU CAMERA ID SENSE UP LIGHT CNTL WHITE BAL PICTURE D/N CNTL FOCUS ADJ MISC NORMAL ATW VIDEO END INIT UNLOCK Please adj focus Press ENTER to exit This function help user to adjustment suitable position for lens focus. When Completed the focus adjust press the ENTER key back to Setup Menu. 6.8 MISC This function is to adjust the camera s synchronization and lens applications. Move cursor to MISC and press Enter. 1. EXTSYNC ENTER Press LEFT or RIGHT key to select the type of camera s synchronization, then press ENTER key to enter external sync phase adjusting menu. Align sync phase by press LEFT or RIGHT key. 2. AUTO IRIS Press LEFT or RIGHT key to select the type of Auto-iris lens: DC lens / Video lens. 3. H/V MIRROR Press LEFT or RIGHT to Left/right reversal (H) or Top/bottom reversal (V) or rotates the image 180 degrees (H/V). Only applicable for WDS-HDR1527DN MISC MENU EXT SYNC INT AUTO IRIS DC LENS H/V MIRROR MASK SYSTEM HOUR: 08 MIN: OO SYSTEM TIME: DISPLAY WDS-HDR1520 MISC MENU EXT SYNC INT AUTO IRIS DC LENS H/V MIRROR MASK WINKER

13 7. SPECIFICATIONS Image device 1/3 interline transfer Super HAD CCD Signal system PAL or NTSC standard Picture elements PAL: 795(H) x 596(V), NTSC: 811(H) x 508(V) Scanning system PAL: 625 lines, NTSC: 525 lines, 2:1 interlace Sync system DC Internal/ AC Line lock sync Horizontal resolution Color: 520 TV Lines BW: 570 TV-Line WDS-HDR 1527DN Color: 520 TV Lines WDS-HDR1520 Minimum illumination: 0.5Lux at F1.2 (30 IRE, AGC 36dB) Aperture correction V aperture-gain adjustable Gain AGC 0-36dB S/N ratio Better than 50dB Contrast level 400:1 Wide dynamic range 52dB Frame integration 2X~160X Masking 8 areas ON/, color, position, size adjustable. E-ZOOM 3 types E-ZOOM (Normal mode only) Mirror Horizontal, Vertical, 180 Auto exposure system 1. AES mode (auto) : 1/50(1/60) - 1/100,000 sec. 2. Auto iris mode : 1/50(1/60) sec. Manual exposure system Shutter speed: 1/50(1/60), 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 sec. Gain: AGC 0~36dB White balance ATW : Max 2500 K K Push to lock : gain memory PRESET : Indoor mode 3200 K, Outdoor mode 6300 K, fluorescent mode 4200 K Manual mode R gain, B gain adjustable Day & Night Only for 1527 DN Video output signal Gamma correction 1, Auto detect: D/N switch illumination level, Delay times 2, D/N by Schedule: Day to Night to day time 3, D/N by External: Hi (DC 5 V) or Low (DC 0V) switch to night mode 4, Day mode 5, Night Mode Composite (BNC): 1.0 Vp-p at 75Ω loads Y gamma curve selectable OSD presentable function 1. Camera ID: up to 12 characters alphanumeric, position 2. Sense UP: 2X ~160X 3. Light control: WD mode: 6 preset setting NORMAL mode: AES, AUTO IRIS, ME, BLC ON/, AGC 0~15 (36dB), FLICKERLESS (NTSC only), E-ZOOM 4. White balance: ATW, Preset, Manual, PTL 5. Sync system selection, phase adjustment 6. Picture Brightness, gamma, aperture correction 7. Miscellaneous: Lens selects, IRIS Level, Mirror, Mask, Winker 8. OSD menu lock -13 -

14 Auto iris lens Accepts video or DC drive iris lens Lens mount C & CS mount Operating temperature -10 C to 50 C Power source DC 12V AC 24V /DC 12V AC 85 ~ 265 V Power consumption: 5.5 W (DC type) 5.8 W (AC type) WDS-HDR1527DN 4.2(DC type) 4.5(AC type) WDS-HDR1520 Dimensions (W x H x D): 71 x 52 x 128 mm Memorandums -14 -

15