ALI-IPU3130R, ALI-IPU3230R IP Bullet Camera Quick Installation Guide

Transcription

1 ALI-IPU3130R, ALI-IPU3230R IP Bullet Quick Installation Guide What s in the box Your camera includes the items shown below. Security L-wrench CD-ROM with manuals and software This document guides you through the basic steps to install and configure the ALI-IPU3130R and ALI-IPU3230R cameras. These cameras feature: 3 MP high resolution sensor IR range 100 ft (ALI-IPU3130R) and 260 ft (ALI-IPU3230R) Full 1080P HD real-time video with H.264 compression 3D-DNR noise reduction, Wide Dynamic Range (WDR), Backlight compensation Dual power capable - Power over Ethernet (PoE) or 12 Vdc Weatherproof - IP66 rated For more information about the software features of this camera, please refer to the ALI-IP Software User Manual. Adapter plate Surface mount drill template Weatherproof LAN coupling Mounting hardware Junction box (top view) Junction box assembly (see detail below) Step 1. Install the camera mounting base Sun Shield The camera includes hardware to install it directly to the Junction box provided, to a mounting surface (without the junction box), or to a double-gang electrical box using the adapter plate provided. When using the junction box, camera LAN and power drop cables can attach to extension cables inside the box. The camera with or without the junction box can be installed on a ceiling (horizontal surface) or wall (vertical surface). To install the camera, do one of the following: To mount the camera using the Junction box 1. Determine the best fasteners for securing the Junction box to mounting surface. The mounting hardware provided is suitable for most surfaces. 2. Remove the junction box from the camera assembly by loosing the four captive screws. 3. Attach the drill template to the surface. Mark the location of the Junction box mounting screw holes. If routing extension cables for the LAN, power, alarm devices, etc. through the mounting surface, mark the location for that hole too. NOTE: If installing the box onto a wall, observe the orientation for TOP and BOTTOM orientation markings inside the box and on the camera mounting base, and orient the drill template properly. Articulated mounting bracket body ALI-IPU3130R, ALI-IPU3230R camera Lens Mounting surface base locator pins Top (up) Bottom (down) Mounting screw hole (4) Hole for camera mounting screw (4) Cable access through mounting surface Junction box Safety cable Drill template Junction box mounting screws (4) Orientation mark Conduit port (2) Junction box detail Ethernet connector - PoE capable Mounting base screws (4) 4. Drill holes in the mounting surface for the mounting screws and extension cables (if necessary). 5. Secure the Junction box to the mounting surface using appropriate fasteners. 6. Route the network LAN and power extension cables between the junction box and the devices they connect to. Do not apply power to the extension cables at this time. 7. Attach the camera safety cable to the safety hook inside the junction box. drop cables 12 Vdc Power connector To mount the camera onto a surface without the junction box For this mounting option, the drop cables can be routed through the mounting surface, or through the cable channel in the mounting base. 1 ALI-IPU3130R-3230R_CQ 4/23/15

2 Mounting surface 2. Secure the camera to the mounting surface or Junction box using appropriate screws. 3. Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured. Step 3. Install the Alibi Discover Tool Cable channel The Alibi Discover Tool is a software utility used to discover Alibi cameras and NVRs/DVRs installed on the LAN and change their network settings. The tool is provided on the CD with your camera. To use the tool: Mounting base screws (4) 1. Insert the software CD provided with your camera into an optical drive on the Microsoft Windows computer you will use to access your camera on the LAN. 2. On the CD, find the folder that contains the Alibi Discover Tool. 3. Copy the files in the folder to a new directory on your computer. The files should appear as shown in the directory shown below. 1. Determine the best fasteners for securing the camera mounting base to mounting surface. The mounting hardware provided may be suitable for some surfaces. 2. Remove the junction box from the camera assembly by removing the four mounting base captive screws. 3. Using the camera mounting base as a template, mark the locations of the holes for the mounting screws. Also mark the location of a hole for the camera drop cables if needed. 4. Route extension cables from the power source and LAN switch (or LAN with PoE) to the mounting location. To mount the camera onto an electrical box 1. Install a double-gang electrical box at the location where the camera will be installed. 2. Attach the adapter plate provided to the electrical box using four (4) screws. Double-gang box 4. To open the Alibi Discover Tool, double click the file Alibi Discover Tool.exe. The tool will automatically discover Alibi cameras and recorders installed on the network. Adapter plate Orientation mark Adapter plate mounting screws (4) Mounting base screws (4) 3. Remove the junction box from the camera assembly by loosing the four mounting base captive screws. 4. Attach the adapter plate to the double-gang box using at least two (2) screws. 5. Route extension cables from the power source and LAN switch (or LAN with PoE) into the electrical box, and then up through the cable opening in the adapter plate. Step 2. Connect camera drop cables to LAN and power 1. Connect the network LAN and power extension cables to the camera drop cables: a. Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from moisture and other contamination, if necessary. A weatherproof fitting is provided. b. If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc power cable to the camera drop cable. The polarity of the drop cable connector is shown below. In the screen shown above, an ALI-IPU3230RV camera was discovered. This camera, although installed on a subnet other than the one implied by its IP address is shown, is still found by the tool. 5. To change the network settings of the camera to be compatible with the subnet where it is installed, do the following: a. Click the device to highlight it. Notice that the network parameters are populated in the frame on the right. CAUTION Do not apply power to the camera at this time. Before applying power to the camera, ensure that the polarity is correct. An incorrect connection may cause a malfunction and can damage the camera Observint Technologies. All rights reserved.

3 2. In the login window, enter your User Name and Password in the appropriate fields, then click Login. The default User Name and Password for Alibi cameras is admin and If this is the first time you are logging into a camera at this IP address AND you are using Internet Explorer 10 or newer, you must configure it for Compatibility mode: a. In Internet Explorer, click the Tools icon (located to the right of the tabs), then select Compatibility View settings from the drop-down menu. Tools icon b. Modify the network settings to values compatible with the subnet where it is installed. c. Enter the admin password for the device in the password field. By default, the admin user password for Alibi cameras is d. Click the Save button. The new IP address, port, and other settings will appear in the list with the device you modified. b. In the Compatibility View Settings window, ensure that the IP address of your camera is in the Add this website field, then click Add. 6. Close the Alibi Discover Tool by clicking the Close icon ( T ) in the upper-right corner of the screen. Step 4. Remote login c. After clicking Add, the IP address will appear in the Websites list. Click Close. 4. If this login is the first login to an Alibi camera from your computer and browser, continue with the following sub-steps to install WebComponents: a. After a successful login to the NVR, a message will appear in the middle of the Live View window requiring you to load a plug-in. Click on the message to continue, then click Run in the pop-up block at the bottom of the screen. To access the camera from a computer on the LAN: 1. Open your Microsoft Internet Explorer browser on your compute and enter the IP address of the camera in the URL field. In the example below, the IP address of the camera is Observint Technologies. All rights reserved.

4 Some computer security software may attempt to block you from running WebComponents.exe. If necessary, open the Internet Explorer downloads list, right click on the WebComponents.exe file name, then click Run Anyway. Step 5. Adjust the camera for your surveillance target 1. While observing live video from your camera, unscrew the Pan, Tilt and Rotation lock screws at least two turns using the security L-wrench provided, then move the camera to point at the center of your surveillance target. Tighten the lock screws to hold the camera in position. NOTE Pan lock screw - Pan: 0 ~ 360 b. In the Setup - WebComponents window opens, click Next to continue. Tilt lock screw Tilt: 0 ~ 100 Step 6. Rotation lock screw Rotation: 0 ~ 360 Setup the video image The video Display Settings menu includes the image-related configurable parameters for the camera. It contains several sub-menus such as Image Adjustment, Exposure Settings, Day/Night Switch, etc. that can be opened or closed for compactness. Additionally, several adjustments can be seen in the Live View image on the menu. To open the Display Settings menu, go to Setup tab Image Display Settings Installing the WebComponents plugin may require that you close the browser. Follow the on-screen instructions, then restart your browser after the installation is finished. c. Allow the plug-in installation to complete. When the following window appears, click Finish. After logging into the camera, the Live View - Main stream window will appear. Live View options Screen select tabs Live View image Logout button Configurable parameters include: Switch Day and Night: Select either Auto-Switch or Scheduled-Switch. If using Auto-Switch, open the Day/Night Switch submenu to select the Sensitivity, Filtering Time, and Smart IR feature ON or OFF. If using Scheduled Switch, set the Start Time and End Time of the switch, then open the Day/Night Switch submenu to select the Smart IR feature ON or OFF. Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness, Contrast and Sharpness for Day and for Night modes. Capture, Record, Enable e-ptz icons Observint Technologies. All rights reserved.

5 Image Adjustment submenu: Open the Image adjustment submenu to set the Saturation, Hue, Brightness, Contrast and Sharpness of the video image. Each parameter can be set to a level of 0 ~ 100 either by moving the slider or entering the value in the box on the right. The effect of the adjustment will appear in the Live View image in the menu. Exposure Settings submenu: In this submenu, set the following for the best performance: Iris Mode: Select Auto or Manual. Some cameras may not offer both options. Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150. Adjust it according to the lightening condition. Gain: Set the gain to show the optimal brightness level. Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or Schedule. The option you select determines the submenu options. Day or Night: These options both have one parameter: Smart IR. Auto: If you select Auto switch, you can set the sensitivity (0.. 7), filtering time and Smart IR. Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart IR is also selectable. Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right Center), the area to control, and WDR (Wide Dynamic Range) ON or OFF. White Balance: White Balance selection is used to correct colors in the image depending on the lighting source. You can also set the white balance manually (MWB), using Automatic White Balance (AWB1), and lock the white balance setting (Locked WB). Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR) ON or OFF. If ON, yo can also adjust the level of noise reduction. Video Adjustment: Video Adjustment includes: Mirror: Mirror adjustment enables you to flip the image (Up/Down), flip Left/Right (reflect or Center). Rotate: Rotate rotates the image +90 degrees. Rotate and Mirror can be used to adjust the image in any orientation. Video Standard: Select 60 Hz for NTSC format. Capture Mode: To make a complete use of the 16:9 aspect ratio, you can enable the capture mode when you use the camera in a narrow view scene. Specifications Product ALI-IPU3130R ALI-IPU3230R Image Sensor 1/3 CMOS Scanning Mode Progressive Scan Resolution Up to 2048 x 1536 Effective Pixels Approx. 3.0 Megapixel Minimum Illumination Color: 0.07 Lux (F2.0, AGC On) B/W: 0 Lux (IR ON) Day/Night True Day/Night ICR) Electronic Shutter (sec) 1/3 ~ 1/100,000 (Auto/Manual) Wide Dynamic Range Digital WDR Gain Control Auto White Balance Mode Auto Noise Reduction 3D DNR IR Illuminators Smart IR Array, 850 nm IR Array Range 100 ft 260 ft IR Sensitivity nm Lens Lens Type Fixed Focal Length 4 mm 6 mm Iris Fixed Focus Manual Horizontal Viewing Angle F-number F2.0 Video Video Compression Format H.264 (Main Profile), MJPEG CODEC Streaming Capability Dual Streaming Maximum Frame Rate x 1536, p Bit Rate 32 kbps ~ 16 Mbps Product ALI-IPU3130R ALI-IPU3230R Bit Rate Mode CBR, VBR Features Motion Detection Backlight Compensation Event Notification Alarm Output, , FTP Privacy Mask Video Analytics Tamper Detection, Line Crossing, Intrusion Detection Interface Ethernet RJ-45 10/100 BASE-T Network Protocols TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour, ONVIF, PSIA Security Password Protection, IP address filtering Number of Connections Up to 10 General Power Requirements PoE (IEEE802.3af) / 12 Vdc Power Consumption 6 W max (IR ON) 10.5 W max (IR ON) Weight 2.65 bs Dimensions 3.4 H x 3.35 W x 11.8 L operating Temperature -22 F ~ 140 F Operating Humidity 0% ~ 95% RH, Non-condensing Ingress Protection IP66 Color White Material Aluminum (body) / Plastic (Sunshield) Approvals CE, FCC, RoHS System Requirements Operating System Microsoft Windows XP Professional, Windows VISTA, Windows 7, Window 8 Processor Intel Pentium GHz or later Memory 1 GB or above RAM Display 1024 x 768 resolution or higher Web Browser Microsoft Internet Explorer 6.0 or above, Apple Safari 5.02 or above, Mozilla Firefox 3.5 or above, Google Chrome 8 or above Supplied Accessories CD ROM (User s Guide, Installation Tools) Quickstart Guide Mounting Hardware and Template Junction box, Gang box adaptor plate Observint Technologies. All rights reserved..