DVALT User Manual. Please read this manual carefully before using this device, and please keep it properly for future use.

Transcription

1 DVALT User Manual Please read this manual carefully before using this device, and please keep it properly for future use.

2

3 WARNING: This device is a driver assistant (or driver aid). The driver ultimately is responsible for ensuring the safe operation of the vehicle. This device does not communicate with the vehicle and is only a supplemental warning measure. Road conditions, installation, weather conditions, visibility, and other factors may affect the accuracy of this device. You should keep your eyes on the road at all times, be alert and look to your left and right before changing lanes. Look ahead to make sure you have enough distance between your car and car ahead and make sure you don't depart your lane inadvertently. Use of this product does not relieve the driver from making sure that the vehicle is being driven in a safe and legal manner, and the manufacturer does not accept any liability for its use. Please do calibration when you rst time using this camcorder. For your safety,please park the car at a safe place to do the calibration.

4 DVALT User Manual Catalogue I. Introduction-----Page 5 II. Notes on Installation-----Page 5 III. Battery warning-----page 6 IV. Caution-----Page 6 V. Product Overview----Page 7 VI. Package Contents -----Page 8 VII. Installation-----Page 8 VIII. Buttons Function-----Page 10 IX. Power ON/OFF-----Page 10 X. Using the Camcorder-----Page 11 XI. LDWS Calibration-----Page 14 Long Press Menu/Mode button to Settings-----Page 17 XII. Main speci cations and parameters-----page 19

5 I.Introduction Thank you for purchasing this advanced camcorder. This camcorder is speci cally designed for real time video and audio recording when driving. II.Notes on Installation 1. Do NOT setup the camcorder while driving or while the vehicle is in motion.please stop at a safe place before adjusting or installing. 2. This camcorder should be installed in a proper manner, without interfering with the driver's eyesight or Driver's eyesight,airbags or any other safety restraint system. Install the camcorder above the rear-view mirror to obtain the best open- eld view. Do NOT install the camcorder in a location that will obstruct your required driving view. 3. Make sure that the lens is within the wiping range of the windscreen wiper to ensure a clear view even when it rains. 4. Do not touch the lens with your ngers. Finger grease may be left on the lens and will result in unclear videos or snapshots. Clean the lens on a regular basis. 5. Keep the product away from strong magnetic elds, which may cause damage to this product. 6. During formatting and use, do not disconnect the power supply, or insert/remove the TF card, otherwise it is likely to damage the TF card or cause program error. 7. TF card in this product is not intended to store any other les. Before it is used, format the TF card, and promptly back up important videos and images. 8. To prevent electric shock, do not insert or remove the power plug with wet hands. 5

6 9. Do not use this product in places with high humidity or temperature above 70 or below Only use the dedicated charger and related accessories compatible with this product. 11. Use TF memory card of Class10 and 8G, or above. III.Battery warning Never dismantle, crush, or pierce the battery, or allow the battery to short-circuit. Do not expose battery being placed in high temperature environment, if battery leaks or bulges, stop continue to use. Always charge using the system. Risk of explosion if battery is replaced by an incorrect type. Keep the battery out of reach of children. Batteries may explode if exposed to naked re. Never dispose of batteries in a re. Never replace the battery on your own; have the dealer do it for you. Disposed of used batteries observing local regulations. IV.Caution Never disassemble or attempt repair of this product. Doing so may damage the camcorder, cause electric shock and void your product warranty. Set up time and date accurately before you use this camcorder. Exposing the camcorder to open ames can cause explosion. Due to local laws and vehicles safety considerations, do not manually operate the camcorder while driving. The values displayed in this system, such as speed, position, and the distance warning to the speed camera set points, may be Inaccurate due to the in uence of surrounding environment. They are for your reference only. 6

7 Power acoustik Company is NOT responsible for the loss of any data/content during operation. V.Product Overview RESET Button Menu/MODE Button OK Button Indicator Light TF Card Slot UP Button DOWN Button MIC Bracket Slot POWER Button USB connector

8 VI. Package Contents The package contains the following items. If there are any missing or damaged items, contact your dealer immediately. Car Camcorder Bracket Car Charger USB Cable Warranty Card User Manua VII.Installation 8

9 1.Use a lint-free cloth to wipe off dust on the location of the windshieldwhere you want to install the product. 2.Please remove the protective lm of bracket suction cup, and attach the camcorder to windshield as picture Fix the bracket well and ensure the camcorder doesn't remove, as picture It is recommended to run the wire along the top of the headliner, down the passenger A-Pillar* and toward the power input. DO NOT POWER ON yet. 5.Plug the other end of the car charger to the cigarette lighter socket of your vehicle. Once the vehicle engine is started, the camcorderautomatically powers on. 6.Ensure all the adjustments on the bracket are right and secure before the vehicle is moved. Note: If the vehicle is equipped with an airbag(s) on the A- Pillar, carefully placethe wire where it will NOT prohibit the airbags from in ating. If you are uncertain or uncomfortable with continuing the install, seek a professional installer. 9

10 VIII.Buttons Function Mode POWER Button UP Button DOWNButton OK Button MENU/MODE Button Video recording mode Camera Mode Long Short press press Power-off Emergen cy Recordin g Power-off Take Photo Long press Short press Long press Short press Long Short press press ON/OFF Play/ recordi Pause ng recordi ng Long press Call up the setup menu Call up the menu Short press Enter the selection mode Enter the selection mode List mode Power -off Select last le, Select next le, Delete the text. Play the Call up selecte the d le. menu Enter the selection mode Play mode Power-off Play Menu mode Mode selection Power-off Power-off last le. Slow play Switch to last menu. Switch to last mode icon, Play next le. Switch to fast IX.Power ON/OFF 1. Automatic power-on/off A) The unit will automatically turn on and record after detecting the external power supply (car start). B) When the external power supply is stopped, the data will be automatically saved and the DVR will be poweroffautomatically. 2. Manually power-on/off Press the POWER button shortly to enter the power on, press and hold for seconds will be power off. Note: 1 First insert the TF card and then boot, if the boot and then insert the card is incorrect; play speed. Switch to next menu, Switch to next mode icon, Play/Pa use Con rm Back to Con rm Previous mode/ exit mode. Back to List Exit to the selection mode. 10

11 2 Please con rm the DVR has power supply by car charger, and the DVR are used in conventional vehicle environment. 3. Indicator light A) Power on: the machine boot indicator light. B) Video: The machine video indicator is ashing continuously. X.Using the Camcorder 1. Record Record interface as below: REC FHD M 2017/05/23 12:26:52 0:00:00 1 Record status 2 Record resolution 3 TF card status(inserted) 4 Battery status 5 GPS status 6 Recording length 7 Recording time and date 8 The distance of front car 7 1. The system will record automatically when start it up eachtime. 2. Loop recording:default loop recording,default record time is3 minutes. Note: the device will enter record interface automatically when start it up. 6 11

12 1) Emergency recording a. Manual Emergency recording: In the recording mode, short press the POWER button,the current video and the previous video of the current video and the next video of the current video are locked into emergency video. (Note: the length of the current video is the length of loop recording) b. Automatic emergency recording: Upon vehicle impact or when G-sensor sensor value reaches the G-sensor setting value, the device will enter emergency recording, the current video and the current video of the previous video and the current video of the next video are locked as emergency video. (Note: Note: the length of the current video is the length of loop recording) 2. Take pictures Take pictures as below: TF card status (inserted) Battery status The rest number of photos Photo time and date 12

13 1) Press the MODE key to switch mode in the recording mode interface or the playback mode interface. Press OK to enter the camera interface, press the POWER button brie y to take pictures. 2) Adjust the focal length of the camera by pressing the UP / DOWN button. 3. Playback In video MODE interface & photographed interface press MODE key switch MODE them press OK button to enter lm list/emergency/photo list interface, to view has been lmed video or photos, etc. For example, lm list interface as the following gure: The list interface: OK button: Play/Pause; UP button:last le; DOWN button:next le; Video playback interface: OK button: Play/Pause; MENU button: Quit playing; Photo list interface: OK button: Play UP button: Last le; Down button:next le; MENU/MODE button: Quit playing 13

14 XI:LDWS Calibration Long Press Menu/Mode button to Settings. 1. Movie Clip Time The time of loop video recording: Click the UP or DOWN button to move up or down to set the recording time: 5min,3min or 1min for choosing.and then short press OK button to con rm. 2. Sound Record Sound recording, click the UP/DOWN button to move up or down to set either ON or OFF. And then short press OK button to con rm. 3. ADAS including auxiliary driving lane deviation warning and collision warning before the car,open the corresponding function,the system starts monitoring,such as:if the detected lane drifting too close to or away from the car,the voice will be sent a Di-Di-Di reminder. 1) LDWS (Lane Departure Warning System):Warning prompts assist the driver by way or reducing vehicle traf c accidents due to lane off set.when the system detects the vehicle lane deviation, will issue a shiftlane the voice prompts. 2)FCWS (Forward Collision Warning System): The distance between vehicles detected. Distance 15 meters ahead of the vehicle automatically detects and issued with the vehicle in front of less than 15 meters away from the Di-Di-Di from voice prompt,safe driving;when the vehicle distance greater than 15 meters,the warning is automatically released. Note: Lane Departure Warning System minimum trigger speed of 30km/h,such as trigger not meet the minimum speed,will not start lane drifting warning. 4.Volume Click the UP/DOWN button to move up or down to adjust volume. 14

15 Optional volume is from 1 to 10 and then short press OK button to con rm. 5. Delete Click the UP/DOWN button to move up or down to delete single le or all les, and then short press OK button to con rm. 1. Protect Click the UP/DOWN button to move up or down to protect/release les, and then short press OK button to con rm. 2. Beep Press UP/DOWN button to select click status: open / close, shortly press OK button to nish selecting. 3. Clock Setting Press UP/DOWN button to select time and shortly press OK button to nish time setting,shortly press OK button to exit setting. 4. Date Format Press Menu/Mode button to select date format: Year/month/date, month/date/year or date/month/year; Shortly press Ok button to nish setting. 5. Language Selection Press UP/DOWN button to select Language: English /Spanish, shortly press OK button to nish selecting. 6. Flicker Press UP/DOWN button to select frequency:50hz/60hz;shortly press OK button to nish selecting. 7. LCD Power Save Press UP/DOWN button to select when the screen goes to sleeping mode:1 min/3 min; Shortly press OK button to nish setting. 15

16 8. Beep Press UP/DOWN button to select click status: open / close, shortly press OK button to nish selecting. 9. Clock Setting Press UP/DOWN button to select time and shortly press OK button to nish time setting,shortly press OK button to exit setting. 10. Date Format Press Menu/Mode button to select date format: Year/month/date, month/date/year or date/month/year; Shortly press Ok button to nish setting. 11. Language Selection Press UP/DOWN button to select Language: English /Spanish, shortly press OK button to nish selecting. 12. Flicker Press UP/DOWN button to select frequency:50hz/60hz;shortly press OK button to nish selecting. 13. G-sensor Press UP/DOWN button to select protect level (G-sensor sensitivity level): OFF/ High/ Middle/Low. Shortly press OK button to nish selecting. 14. Parking Monitoring Press UP/DOWN button to set Parking Monitoring ON & OFF. Shortly press OK button to nish selecting. 15. GPS Status: Display GPS signal status 16. Time Zone Select Press UP/DOWN button to set time zone; Shortly press OK button to nished selecting. 16

17 17. Reset Setup Return the unit back to factory default setting. Press UP/DOWN button to select reset status: Yes / No; Shortly press OK button to nished selecting. 18. Format SD Card. Press UP/DOWN button set format SD card status: Yes / No, Shortly press OK button to nished selecting. 19. LDWS Calibration. Please do calibration when you rst time using this camcorder. For your safety,please park the car at a safe place to do the calibration. Go to Setting and click on LDWS Calibration into the driveway calibration interface. There are the three steps: 1.Set Red Line to Horizon. Adjust the DVR position till match the horizon line,press the DVR up and down'' buttons,till the lines match. Press O button to con rm when nish. Red line to Honzon. Adjust Menu Exit OK Next 17

18 2.Set Green Line to Car Hood. Set Green Line to Car Hood Adjust Menu Exit OK Next Adjust the DVR position till match the horizon line,press the DVR up and down'' buttons,till the lines match. Press O button to con rm when nish,will go to next calibration. 3.DVR Height from road surface. HEIGHT FROM ROAD SUV CAR 100 Maximal Height:220cm. Minimum Height:100cm. Default Setting: Sedan Car Set at 120. SUV Car Set at 140. Adjust Menu Exit OK Next Note:The calibration is very important.it may cause the ADAS work unproperly if calibration hasn't set well. 18

19 XII.Main speci cations and parameters LCD Panel 1.5 inch TFT Lens 143 A+HD wide Angle lens Language selection English/Spanish Video resolution 1920*1080p/30fps Video format MOV Photo format JEPG Memory card Micro SD Max 64GB TF card Microphone /Speaker Support G-Sensor Support Frequency 50HZ/60HZ USB interface USB2.0 Power input 5V 1.5A Battery Polymer battery 160mAh Default Setting 1. Movie Clip Time 3min 2. Sound Record ON 3. LDWS ON 4. FCWS ON 5. Volume 5 6. Delete Delete One 7. Protect Protect One 8. Beep On 9. Clock Settings 10. Date Format YYYY MM DD 11. Language English 12. Flicker 50Hz 13. LCD Power Saver Off 14. G-sensor ---Middle 15. Parking Monitoring Off 16. GPS Status 17. Time Zone Select GMT-08: Reset Setup 19. Format SD-Card 20. FW Version 19

20