Micrometers. Micrometer Heads

Transcription

1 B Small Tool Instruments Micrometers Micrometers Heads Micrometers Micrometer Heads MDC Micrometer MDH Micrometer QuantuMike Digimatic Outside Micrometer Micrometer Head with spindle clamp INDEX Micrometers Coolant Proof Micrometer B-2,3 Digimatic Micrometer B-4 Digimatic Micrometer- MDC- Lite B-4 MDH Micrometer B-5 QuantuMike B-6 ABSOLUTE Digimatic Micrometers B-7 Quickmike B-8 Outside Micrometers B-9 Ratchet Thimble Micrometer B-1 Outside Micrometers B Spline Micrometers B-2 Point Micrometers B-21 Crimp Height Micrometers B-22 V-Anvil Micrometers B-23,24 Limit Micrometers B-25 Pana Micrometers B-26 Spherical Face Micrometers B-27 Tube Micrometers B-28 Uni-Mike B-29 Sheet Metal Micrometers B-3 Blade Micrometers B-31 Disk Micrometers B-32 Paper Thickness Micrometers B-33 Disk Micrometers B-34,35 Gear Tooth Micrometers B-36 Screw Thread Micrometers B-37 Screw Thread Micrometers B-38 3-Wire Thread Measuring System B-39 Can Seam Micrometers B-4 Hub Micrometers B-41 Wire Micrometers B-41 Digit Outside Micrometers B-42 Indicating Micrometers B-43 Snap Meters B-43 Dial Snap Meters B-44 Caliper Type Micrometers B-45 Groove Micrometers B-46 Small Hole Gage Set B-47 Telescoping Gage Set B-47 Micrometer Stands B-48 Color Ratchet & Color Speeder B-49 Spindle Attachment Tip B-49 Micrometer Oil B-49 Optical Parallels B-5 Optical Flats B-5 Micrometer Standards B-51 Standards for Screw Thread Micrometers B-52 Standards for V-Anvil Micrometers B-52 Tool Kits B-53,54 Micrometer Heads Micrometer Head Selection Guide B-55 Digimatic Micrometer Heads B-56 Digimatic Micrometer Heads B-57 Micrometer Heads B Digital Micrometer Heads B-72 Micrometer Heads B-73 Micro Jack B-73 Precision Lead Screw B-74 Fixtures for Micrometer Heads B-75,76 B-1

2 Coolant Proof Micrometer SERIES 293 with Dust/Water Protection Conforming to IP65 Level IP65 protection level, enabling use in environments exposed to cutting oil, etc*. *Anti-corrosion treatment is required after use. Measurement data output function is available with a water-resistant connection cable. Auto power ON/OFF function. A nonslip surface with raised dots is employed for the frame cover and surface panel to achieve stable handheld measurement. Certificate of inspection* is included. (2 /5mm or less range models) *It is not the type used to obtain calibration certificates. With a standard bar except for -1"/-25mm model. Supplied in fitted case. Plastic case up to 6"/15mm, wooden box over 6"/15mm Employed nonslip surface with raised dots Certificate of inspection Accuracy: Refer to the list of specifications. Resolution:.5"/.1mm or.1mm (up to 4 models).1 /.1mm (over 4 models) Flatness:.12 /.3µm Parallelism:.4 /1µm for models up to 2 /5mm.8 /2µm for models up to 4 /1mm.12 /3µm for models up to 7 /175mm.16 /4µm for models up to 11 /275mm.2 /5µm for models over 12 /3mm Measuring faces: Carbide tipped Display: LCD Battery: SR44 (1 pc.), Battery life: Approx. 2.4 years under normal use (8 months: over 4 /1mm models) Dust/Water protection level: IP65 Function Origin-set, Zero / ABS, Hold, Auto power on/off, Data output (output models), inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories 5CZA662: SPC cable with data switch (4 /1m) 5CZA663: SPC cable with data switch (8 /2m) USB Input Tool Direct USB-ITN-B (2m): 6ADV38B Oil-resistance materials are used in all plastic components. B-2 Measurement data output function is available with a water-resistant connection cable. SPC cable with data switch Connecting cable for U-Wave-T (16mm) 2AZD79B Refer to page A-13.

3 Range Resolution Order No. Accuracy - 25mm.1mm / * ±1µm 25-5mm.1mm / * ±1µm 5-75mm.1mm / * ±1µm 75-1mm.1mm / * ±2µm 1-125mm.1mm ±2µm mm.1mm ±2µm mm.1mm ±3µm 175-2mm.1mm ±3µm 2-225mm.1mm ±3µm mm.1mm ±4µm mm.1mm ±4µm 275-3mm.1mm ±4µm *without SPC data output Range Resolution Order No. Accuracy - 25mm.1mm / * ±1µm 25-5mm.1mm / * ±1µm 5-75mm.1mm / * ±1µm 75-1mm.1mm / * ±2µm *without SPC data output With ratchet stop With ratchet thimble Micrometer Set Range Order No. Included in set -5mm (2pcs. Set) , , 25mm CERA block, plastic case -75mm (3pcs. Set) , , , 2 standard bars, plastic case -1mm , , b (4pcs. Set) , , 3 standard bars, wooden box Ratchet stop type (up to 1mm/4 ) c DIMENSIONS AND MASS a / Range Resolution Order No. Accuracy - 1" / mm.5 /.1mm / * ±.5" 1" - 2 / mm.5 /.1mm / * ±.5" 2" - 3" / mm.5 /.1mm / * ±.5" 3" - 4" / mm.5 /.1mm / * ±.1" 4" - 5" / mm.1 /.1mm ±.1" 5" - 6" / mm.1 /.1mm ±.1" 6" - 7" / mm.1 /.1mm ±.15" 7" - 8" / mm.1 /.1mm ±.15" 8" - 9" / mm.1 /.1mm ±.15" 9" - 1" / mm.1 /.1mm ±.2" 1" - 11" / mm.1 /.1mm ±.2" 11" - 12" / mm.1 /.1mm ±.2" *without SPC data output / Range Resolution Order No. Accuracy - 1 / mm.5 /.1mm / * ±.5" - 1" / mm.1 /.1mm * ±.1 1" - 2"/ mm.5 /.1mm * ±.5" 2" - 3" / mm.5 /.1mm * ±.5" 3" - 4" / mm.5 /.1mm * ±.1" *without SPC data output With ratchet stop With ratchet thimble / Range With friction thimble Resolution Order No. Accuracy - 1" / mm.5 /.1mm / * ±.5" 1" - 2"/ mm.5 /.1mm ±.5" *without SPC data output L / Micrometer Set.5" /.1mm graduation model Range Order No. Included in set - 3 / mm , , , (3 pcs. set) 2 standard bars, plastic case - 4" / mm , , (4 pcs. set) , , 3 standard bars, wooden box Ratchet thimble type and friction thimble type 1.8 b L c a ø b L a 27.5 C ø19.3 Ratchet stop type (over 1mm/4 to 3mm/12 ) Range ( / ) L a b c Mass (g) - 25mm / (25) mm / (32.5) mm / (47) mm / (6) mm / (76.5) mm / (91) mm / (13.1) mm / (115.3) mm / (126.8) mm / (139.8) mm / 1-11" (152.3) mm / 11-12" (166) 154 B-3

4 Digimatic Micrometer SERIES 293 DIMENSIONS 28 ф12 L a Digimatic Micrometer SERIES 293 MDC-Lite Provided only with a zero set and in/mm (inch/metric models only) keys. A ratchet stop or friction thimble for a constant measuring force. Measurement readout with large characters on the LCD screen. No spindle clamp. No data output Supplied in fitted plastic case ф8 With ratchet stop Range Resolution Order No. Accuracy - 25mm.1mm ±2µm DIMENSIONS AND MASS ф21 33 Range L a Mass(g) 3-325mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ Ratchet stop With ratchet stop Range Resolution Order No. Accuracy 3-325mm.1mm ±6µm mm.1mm ±6µm mm.1mm ±6µm 375-4mm.1mm ±7µm 4-425mm.1mm ±7µm mm.1mm ±7µm mm.1mm ±8µm 475-5mm.1mm ±8µm / Range With ratchet stop Resolution Order No. Accuracy 12" - 13" / mm.1" /.1mm ±.3" 13" - 14" / mm.1" /.1mm ±.3" 14" - 15" / mm.1" /.1mm ±.3" 15" - 16" / mm.1" /.1mm ±.35" 16" - 17" / mm.1" /.1mm ±.35" 17" - 18" / mm.1" /.1mm ±.35" 18" - 19" / mm.1" /.1mm ±.4" 19" - 2" / mm.1" /.1mm ±.4" / Range With ratchet stop Resolution Order No. Accuracy - 1" / mm.5" /.1mm ±.1" / With friction thimble Range Resolution Order No. Accuracy - 1" / mm.5" /.1mm ±.1" 1.8 Friction thimble Accuracy: Refer to the list of specifications. Resolution:.1"/.1mm or.1mm Flatness:.24 /.6µm Parallelism:.2 / 5µm for models up to 15 / 375mm.24 / 6µm for models up to 19 / 475mm.28 / 7µm for models over 2 / 5mm Measuring faces: Carbide tipped Display: LCD Battery: SR44 (2 pcs.), Battery life: Approx. 1.8 years under normal use Function Preset, Zero-setting, Power ON/OFF, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories : SPC cable (4 /1m) Straight type 95915: SPC cable (8 /2m) Straight type 4AZB512: SPC cable L-type (4 /1m) 4AZB513: SPC cable L-type (8 /2m) Accuracy: Refer to the list of specifications. Resolution:.5"/.1mm or.1mm Flatness:.12 /.3µm Parallelism:.8 / 2µm Measuring faces: Carbide tipped Display: LCD Battery: SR44 (1 pc.), Battery life: Approx. 2.4 years under normal use Function Origin-set, Automatic power on/off, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error MASS: 27g B-4

5 Flatness:.3µm/.12 Parallelism:.6µm/.24 Measuring force: 7 to 9N Power supply: Lithium battery 5SAA217 (CR232) x 1 Battery life: Approx. two years when used under normal conditions Functions Preset (ABS measurement system) Zero-setting (INC measurement system) Hold, Resolution switching, Function lock, On/off, Auto power off, Measurement data output, Error alarm Optional Accessories 5CZA662: SPC cable with data switch (1m/4 ) 5CZA663: SPC cable with data switch (2m/8 ) MDH Micrometer SERIES 293 High-Accuracy Sub-Micron Digimatic Micrometer Enabling.5 /.1μm resolution measurement, this micrometer is ideal for customers who need to make highly accurate measurements with a hand-held tool. A highly rigid frame and high-performance constant-force mechanism* enable more stable measurement, while the clicks emitted while the workpiece is being measured assure the operator that measurement is proceeding normally. * Patent pending in Japan, the United States of America, the European Union, and China. Body heat transferred to the instrument is reduced by a (removable) heat shield, minimizing the error caused by thermal expansion of the frame when performing handheld measurements. The ABS (absolute) rotary sensor also eliminates the need to perform origin setting each time the power is turned on, letting you start measuring straight away. With no possibility of overspeed errors, the High-Accuracy Digimatic Micrometer also delivers a higher level of reliability Function lock Heat shield Order No. Range Resolution Accuracy Measuring surface Mass mm.1mm/.5mm (switchable) ±.5μm ø3.2mm 4g (44g w/heat shield) / Order No. Range Resolution Accuracy Measuring surface Mass "/.2" - 1" mm.1mm/.5mm (switchable) ±.2" ø3.2mm 4g (44g w/heat shield) DIMENSIONS ø ø Dimensions shown without heat shield B-5

6 QuantuMike SERIES 293 Coolant Proof Micrometer Faster measurement with 2mm per revolution instead of the standard.5mm. A patented ratchet thimble mechanism helps ensure repeatability. A function lock helps prevent error. IP-65 protection level. Certificate of inspection provided. With a standard bar except for -25mm/-1" model. Supplied in fitted plastic case Certificate of inspection Accuracy: Refer to the list of specifications. Resolution:.1mm or.5"/.1mm Flatness:.3µm/.12 Parallelism: 1µm/.4 for models up to 5mm/2 2µm/.8 for models up to 1mm/4 Measuring force: 7-12N Measuring faces: Carbide tipped Display: LCD Battery: SR44 (1 pc.), Battery life: Approx. 1.2 years under normal use (8 months: over 1mm models) Dust/Water protection level: IP65 specifications Range Resolution Order No. Accuracy -25mm.1mm um -25mm.1mm * 1um 25-5mm.1mm um 25-5mm.1mm * 1um 5-75mm.1mm um 5-75mm.1mm * 2um 75-1mm.1mm um 75-1mm.1mm * 2um * without SPC data output / Range Resolution Order No. Accuracy -1 / mm.5 /.1mm / mm.5 /.1mm * / mm.5 /.1mm / mm.5 /.1mm * / mm.5 /.1mm / mm.5 /.1mm * / mm.5 /.1mm / mm.5 /.1mm *.1 * without SPC data output Function Origin-set, Zero / ABS, Hold, Function locks, Auto power on/off, Data output (output models), inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories 5CZA662: SPC cable with data switch (1m/4 ) 5CZA663: SPC cable with data switch (2m/8 ) USB Input Tool Direct USB-ITN-B (2m): 6ADV38B Connecting cable for U-Wave-T (16mm) 2AZD79B SPC cable with data switch Inspection Gage Block Set Rectangular Steel Gage Block 1 pc. blocks and 1 pc. optical parallel Inspection Gage Block Set Rectangular Cera Gage Block 1 pc. blocks and 1 pc. optical parallel DIMENSIONS AND MASS a L b ø19.3 Model=25-5mm/1-2 B Range L a b Mass(g) -25mm/-1" mm/1-2" mm/2-3" mm/3-4" Time [s] Ratchet on thimble Ratchet on speeder Ratchet-induced microvibrations along the spindle help ensure repeatable measurements Significant reduction in positioning time Time needed to measure a multi-stepped cylindrical workpiece (with one hand) 53 sec. 41 sec. 12 sec. Conventional model Positioning time Measuring time 22 sec. 1 sec. 12 sec. QuantuMike

7 ABSOLUTE Digimatic Micrometers SERIES 227 with Adjustable Measuring Force Accuracy: Refer to the list of specifications. Resolution:.5"/.1mm or.1mm Flatness:.12 /.3µm Parallelism:.8 / 2µm Accuracy of selected measuring force: ± (.1+selected measuring force/1)n for.5-2.5n models ± (.4+selected measuring force/1)n for 2-1N models Measuring faces: Carbide tipped Display: LCD Battery: SR44 (1 pc.), Battery life: Approx. 3 years under normal use (1 year for / 15-3mm, / 1-2mm, /2-3mm range model) Constant and low measuring force mechanism in the thimble. Adjustable measuring force* accommodates various kind of work materials. *.5-2.5N or 2-1N The measurement-value hold function automatically retains the data at a specified measuring force, ensuring accuracy. Non-rotating spindle and the new ratchet friction thimble. Speedy spindle feed by.4 /rev and 1mm/rev for inch/metric model. With absolute linear scale. With SPC data output. With a standard bar to set the origin point (except for -15mm, -1mm, -.6, and -.4 models). Supplied in fitted plastic case Function Origin, Hold / Data, ON/OFF, Zero / ABS, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories : SPC cable (4 / 1m) 96513: SPC cable (8 / 2m) Order No. Range Resolution Accuracy Measuring Force Mass(g) mm.1mm ±2µm (.5, 1., 1.5, 2, 2.5) N mm.1mm ±2µm (.5, 1., 1.5, 2, 2.5) N mm.1mm ±2µm 2-1 (2, 4, 6, 8, 1) N mm.1mm ±2µm 2-1 (2, 4, 6, 8, 1) N mm.1mm ±2µm 2-1 (2, 4, 6, 8, 1) N 415 / Order No. Range Resolution Accuracy Measuring Force Mass(g) ".5"/.1mm ±.1" (.5, 1., 1.5, 2, 2.5) N ".5"/.1mm ±.1" (.5, 1., 1.5, 2, 2.5) N ".5"/.1mm ±.1" 2-1 (2, 4, 6, 8, 1) N ".5"/.1mm ±.1" 2-1 (2, 4, 6, 8, 1) N ".5"/.1mm ±.1" 2-1 (2, 4, 6, 8, 1) N 415 DIMENSIONS AND MASS a L b 4 ø24.5 N N N N Range L a b - 15mm mm Stroke-limiting bush Measuring force control 8.5 a 63.8 L b ø Range L a b 15-3mm mm mm Measuring force control Stroke-limiting bush B-7

8 c Quickmike SERIES 293 IP-54 ABSOLUTE Digimatic Micrometers The Quickmike provides a speedy spindle feed of 1mm /.4 per thimble rotation as compared to the conventional micrometer with.5mm /.25 per rotation. Its wide 3mm / 1.2 measuring range allows various workpieces with different shapes to be measured quickly Non-rotating spindle and the new ratchet friction thimble. Speedy spindle feed by 1mm/rev and.4 /rev for inch/metric models. With absolute linear scale. IP54 dust/water protection (when not connected with data output cable). With SPC data output. With a standard bar to set the origin point (for models with a range over 3mm / 1.2 ). Supplied in fitted plastic case Accuracy: Refer to the list of specifications. Resolution:.1mm or.5"/.1mm Flatness:.3µm /.12 Parallelism: 2µm /.8 for models up to 8mm / 3.2 3µm /.12 for models up to 15mm / 4.2 Measuring force: 5-1N Measuring faces: Carbide tipped Display: LCD Battery: SR44 (1 pc.), Battery life: Approx. 3 years under normal use (1 year for models over 3mm / 1.2 ) Dust/Water protection level: IP Range Resolution Order No. Accuracy - 3mm.1mm ±2µm 25-55mm.1mm ±2µm 5-8mm.1mm ±3µm 75-15mm.1mm ±3µm DIMENSIONS AND MASS / Range Resolution Order No. Accuracy - 1.2" /.5" / ±.1" mm.1mm 1" - 2.2" /.5" / ±.1" mm.1mm 2" - 3.2" /.5" / ±.15" mm.1mm 3" - 4.2" / mm.5" /.1mm ±.15" Function Origin, Hold / Data, ON/OFF, Zero / ABS, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error ABSOLUTE scale with origin point Scale Detector Quick feeding mechanism Lead screw 1mm/rev. b L a ø24.9 Range L a b c Mass - 3mm / - 1.2" mm / 1-2.2" mm / 2-3.2" mm / 3-4.2" Optional Accessories : SPC cable (1m / 4 ) 96513: SPC cable (2m / 8 ) USB Input Tool Direct USB-ITN-E (2m): 6ADV38E Connecting cable for U-Wave-T (16mm) 2AZD79E Refer to page A-13. B-8

9 Outside Micrometers SERIES 11 Graduation:.1" Flatness:.24" Parallelism:.8" for models up to 3".12" for models over 3" Measuring faces: Carbide tipped Satin-chrome-finished frame, tapered (on the anvil side) for hard-to-reach places. With a standard bar except for - 1" models. Supplied in fitted plastic case With friction thimble Range Graduation Order No. Accuracy Mass (g) - 1".1" * ±.1" ".1" * ±.1" 245 *.1" reading is obtained with vernier. DIMENSIONS With ratchet stop Range Graduation Order No. Accuracy Mass (g) - 1".1" * ±.1" ".1" * ±.1" ".1" * ±.1" ".1" 11-12* ±.15" 55 *.1" reading is obtained with vernier. b a L 1.8 c ø ø Unit: inch Range L a b c - 1" " " " Note: The shape of the thimble changes on the model with friction thimble. B-9

10 Ratchet Thimble Micrometer SERIES 11, 12 New smoother action Ratchet Thimble Ratchet function works both from the thimble and the speeder, allowing easy one-handed operation. Clearly audible ratchet operation for reassurance that measurement is being performed at constant, preset force. Provided with a Certificate of Inspection. With a standard bar except for - 25mm and - 1 models. Supplied in fitted plastic case. Thimble sleeve Speeder sleeve Graduation:.1mm,.1mm,.1" or.1" Flatness:.6µm /.24 Parallelism: 2µm /.8 Measuring faces: Carbide tipped Measuring force: 5-1N Rotating the thimble/speeder sleeve when the workpiece is between the anvil and spindle causes the ratchet mechanism to tap the spindle and apply a constant measuring force to the workpiece. Thimble sleeve Speeder sleeve Range Graduation Order No. Accuracy - 25mm.1mm ±2µm - 25mm.1mm 12-77* ±2µm 25-5mm.1mm ±2µm 25-5mm.1mm 12-78* ±2µm *.1mm reading is obtained with vernier. Range Graduation Order No. Accuracy - 1".1" ±.1".1" * ±.1".1" * ±.1" 1-2".1" * ±.1" *.1" reading is obtained with vernier. Ratchet mechanism DIMENSIONS AND MASS mm model / 1-2 model ø mm / - 1 : 18g 25-5mm / 1-2 : 27g 3 11 B-1

11 Outside Micrometers SERIES 12 Graduation:.1mm Flatness:.3µm Parallelism: 1µm for 25mm model 3µm for models up to 1mm Measuring faces: Carbide tipped Heat-insulated frame, tapered (on the anvil side) for hard-to-reach places. With a standard bar except for - 25mm model. A ratchet stop for a constant measuring force. Supplied in a fitted plastic case. Ratchet stop type With ratchet stop Range Graduation Order No. Accuracy - 25mm.1mm ±2µm 25-5mm.1mm ±2µm 5-75mm.1mm ±2µm 75-1mm.1mm ±3µm Micrometer set.1mm Graduation model Range Order No. Included in set - 1mm (4 pcs/set) micrometer standards DIMENSIONS AND MASS b a L ød c Range L a b c d Mass (g) - 25mm mm mm mm B-11

12 Outside Micrometers SERIES 13 Hammertone, baked-enamel-finished frame. Ratchet Stop for exact repetitive readings. With a standard bar except for -25mm model Graduation:.1mm,.1mm Flatness:.6 µm for models up to 3mm/12" 1µm for models over 3mm/12" Parallelism: (2+R/1)µm, R=max, range (mm) Measuring faces: Carbide tipped With ratchet stop Range Order No. Accuracy Mass (g) - 25mm ±2µm * ±2µm mm ±2µm * ±2µm mm ±2µm mm ±3µm mm ±3µm mm ±3µm mm ±4µm mm ±4µm mm ±4µm mm ±5µm mm ±5µm mm ±5µm mm ±6µm mm ±6µm mm ±6µm mm ±7µm mm ±7µm mm ±7µm mm ±8µm mm ±8µm 345 (Models with a range up to 1mm are available.) *.1mm reading is obtained with vernier. DIMENSIONS AND MASS b a Up to 3mm / 12" Over 3mm / 12" c L Range L a b c - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" mm / 4-5" mm / 5-6" mm / 6-7" mm / 7-8" mm / 8-9" mm / 9-1" mm / 1-11" mm / 11-12" b ø12 L a 35 5 c ø ø21 Range L a b c 3-325mm / 12-13" mm / 13-14" mm / 14-15" mm / 15-16" mm / 16-17" mm / 17-18" mm / 18-19" mm / 19-2" Range Micrometer set Order No. Included in set Mass (g) - 75mm (3 pc. set) , , , 2 micrometer 75 standards - 15mm , , , , (6 pc. set) 141-1, , 5 micrometer standards 15-3mm (6 pc. set) , , , , , , 6 micrometer standards mm (12 pc. set) All micrometers of and in one 93 set, 11 micrometer standards B-12

13 Outside Micrometers SERIES 13 Models Hammertone, baked-enamel-finished frame. Ratchet Stop or Friction Thimble for exact repetitive readings. With a standard bar except for -1 model ( Model) Accuracy: Refer to the list of specifications. Graduation:.1" or.1" Flatness:.24 for models up to 12.4 for models over 12 Parallelism: [ (L/4)] L= max range (inch) Measuring faces: Carbide tipped With ratchet stop Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.1" * 2 ±.1" ".1" ±.1" ".1" ±.1" ".1" ±.15" ".1" ±.15" ".1" ±.15" ".1" ±.2" ".1" ±.2" ".1" ±.2" ".1" ±.25" ".1" ±.25" ".1" ±.25" ".1" ±.3" ".1" ±.3" ".1" ±.3" ".1" ±.35" ".1" ±.35" ".1" ±.35" ".1" ±.4" ".1" ±.4" ".1" ±.4" ".1" ±.45" ".1" ±.45" ".1" 13-2 ±.45" ".1" ± ".1" ±.5" ".1" ±.5" ".1" ±.55" ".1" ±.55" ".1" ±.55" ".1" ±.6" ".1" ±.6" ".1" ±.6" ".1" ±.65" ".1" ±.65" ".1" ±.65" ".1" ±.7" ".1" ±.7" ".1" ±.7" ".1" ±.75" 888 ** Tapered Frame With friction thimble Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.1" 175.1" ±.1" ".1" ±.1" 215.1" ±.1" 215 With ratchet stop Range Graduation Order No. Accuracy Mass (g) - 1".1" 13-26* 1, 2 ±.1" 175-1".1" * 1 ±.1" ".1" * 1 ±.1" ".1" * 1 ±.1" ".1" * 1 ±.1" ".1" * 1 ±.15" ".1" * 1 ±.15" ".1" 13-22* 1 ±.15" ".1" * 1 ±.2" ".1" * 1 ±.2" ".1" * 1 ±.2" ".1" * 1 ±.25" ".1" * 1 ±.25" ".1" * 1 ±.25" 1565 * 1.1"Reading is obtained with vernier * 2 Tapered Frame B-13

14 Outside Micrometers SERIES 13 model set Micrometer Set.1 Graduation Model Range Order No. Included in set Mass (g) - 3" (3pcs./set) , , , 2 Micrometer Standards 75-4" (4pcs./set) , , , 13-18, 3 Micrometer Standards 16-6" (6pcs./set) , , , 13-18, , , 22 5 Micrometer Standards - 12" (12pcs./set) , , , 13-18, , , , , , , , , 11 Micrometer Standards 6-12" (6pcs./set) , , , , , , 6 Micrometer Standards Micrometer Set.1 Graduation Model Range Order No. Included in set Mass (g) - 3" (3pcs./set) , , , 2pcs. Micrometer Standards 75-4" (4pcs./set) , , , , 3pcs. Micrometer Standards 16-6" (6pcs./set) , , , , , 13-22, 5 Micrometer Standards 22-12" (12pcs./set) , , , , , 13-22, , , , , , , 11pcs. Micrometer Standards 6-12" (6pcs./set) , , , , , , 6pcs. Micrometer Standards B-14

15 Outside Micrometers SERIES 34, 14 with Interchangeable Anvils, model IP65 water/dust protection (Series 34*). *Models with a range up to12 / 3mm. Wide measuring range with interchangeable anvils. With a Ratchet Stop for constant force. Supplied with zero-setting standards bar for each range. With SPC output (Series 34). Supplied in fitted wooden case Accuracy: ±[ (L/3) ] L = Max Range () Resolution*:.1"/.1mm ( :.5"/.1mm) Graduation**:.1 (14-165: is.1 ) Flatness:.24 for models up to 12.4 for models over 12 Parallelism:.8 for models up to 3.12 for models up to 6 ±[ (L/4) ] L= Max range (inch) Measuring faces: Carbide tipped (spindle only) Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 (up to 12 / 3mm) *Digital models **Analog models Function of Digital Model Zero / ABS, Data hold, Preset, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Function Lock*** 2 Presets*** *** 4-12 / 1-3mm Models Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) / Digital model Range Resolution Order No. Mass (kg) Remarks -6" /.5" / with 6 anvils & 5 standards mm.1mm 6-12" /.1" / with 6 anvils & 6 standards mm.1mm 12-18" /.1" / with 6 anvils & 6 standards mm.1mm 18-24" /.1" / with 6 anvils & 6 standards mm.1mm 24-3" /.1" / with 6 anvils & 6 standards mm.1mm 3-36" / mm.1" /.1mm with 6 anvils & 6 standards Range Graduation Order No. Mass(kg) Remarks *.32 with 1 anvil & 1 standard with 6 anvils & 5 standards with 6 anvils & 6 standards with 4 anvils & 4 standards with 6 anvils & 6 standards with 4 anvils & 4 standards with 6 anvils & 6 standards with 4 anvils & 4 standards with 4 anvils & 4 standards with 6 anvils & 6 standards with 4 anvils & 4 standards with 6 anvils & 6 standards with 4 anvils & 4 standards with 4 anvils & 4 standards with 6 anvils & 6 standards *.1" reading is obtained with vernier. B-15

16 Outside Micrometers SERIES 34, 14 with Interchangeable Anvils, Model IP65 water/dust protection (Series 34*). *Models with a range up to 3mm. Wide measuring range with interchangeable anvils. With a Ratchet Stop for constant force. Digital model Supplied with zero-setting standards bar for each range. With SPC output (Series 34). Supplied in fitted wooden case A Digital model Range Resolution Order No. Mass (kg) Remarks - 15mm.1mm with 6 anvils & 5 standards 15-3mm.1mm with 6 anvils & 6 standards 3-4mm.1mm with 4 anvils & 4 standards 4-5mm.1mm with 4 anvils & 4 standards 5-6mm.1mm with 4 anvils & 4 standards 6-7mm.1mm with 4 anvils & 4 standards 7-8mm.1mm with 4 anvils & 4 standards 8-9mm.1mm with 4 anvils & 4 standards 9-1mm.1mm with 4 anvils & 4 standards Accuracy: ±(4+R/75)µm, R=max. range (mm) Resolution*:.1mm Graduation**:.1mm Flatness:.6µm for models up to 3mm 1µm for models over 3mm Parallelism: 2µm for models up to 75mm 3µm for models up to 15mm (2+R/1)µm for models over 15mm, R=max. range (mm) Measuring faces: Carbide tipped (spindle only) Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 (up to 3mm) *Digital models **Analog models Function of Digital Model Zero / ABS, Data hold, Preset, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Function Lock*** 2 Presets*** ***4-12 / 1-3mm Models Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) Range Graduation Order No. Mass (kg) Remarks - 5mm.1mm *.32 with 2 anvils & 1 standards - 1mm.1mm A.79 with 4 anvils & 3 standards - 15mm.1mm A 1.35 with 6 anvils & 5 standards 5-15mm.1mm A 1.35 with 4 anvils & 4 standards 1-2mm.1mm 14-14A 1.38 with 4 anvils & 4 standards 15-3mm.1mm A 2.65 with 6 anvils & 6 standards 2-3mm.1mm A 2.22 with 4 anvils & 4 standards 3-4mm.1mm A 3.31 with 4 anvils & 4 standards 4-5mm.1mm A 4.81 with 4 anvils & 4 standards 5-6mm.1mm A 6.35 with 4 anvils & 4 standards 6-7mm.1mm A 7.72 with 4 anvils & 4 standards 7-8mm.1mm A 9.8 with 4 anvils & 4 standards 8-9mm.1mm A 1.41 with 4 anvils & 4 standards 9-1mm.1mm A with 4 anvils & 4 standards *The frame is in a heat insulated cover DIMENSIONS a L φ18 φ9.7 φ A ø8 ø Interchangeable anvil L a M1 135 M M M M M B-16

17 Outside Micrometers SERIES 15 with Extension Anvil Collars Accuracy: ±(6+R/75)µm, R=max. range (mm) Graduation:.1 /.1mm Flatness:.52 / 1.3µm Parallelism: [ (L/4) ] L=max. range (inch) (2+R/1)µm, R=max. range (mm) Measuring faces: Carbide tipped Extension anvil collar Wide measuring range with extension anvil collars. 5mm spindle stroke. With Ratchet Stop for constant force. Supplied with zero-setting standards bar for each range. Square and round pipes are combined for light weight and rigid frame (for models over 1mm range). Workpiece stopper (for models over 1mm range). Supplied in a fitted wooden case Range under 1mm model model and over 1mm model Range Order No. Extension collars Mass (kg) 5-6mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm, 1mm mm mm mm mm mm mm, 1mm mm mm mm mm mm mm, 1mm mm mm mm mm mm mm, 1mm mm mm mm mm mm mm, 1mm Range Order No. Extension Mass (kg) collars 4-44" " " " " " " " " " " " " " " " " " " " 16.7 B-17

18 Outside Micrometers SERIES 46 Non-Rotating Spindle Type With a standard bar except for -1 / - 25mm model. With SPC output. Supplied in a fitted plastic case. Digital model with ratchet stop Range Resolution Order No. Accuracy - 25mm.1mm ±3µm 25-5mm.1mm ±3µm 5-75mm.1mm ±3µm 75-1mm.1mm ±4µm Accuracy: Refer to the list of specifications. Resolution:.5 /.1mm or.1mm Flatness:.3µm /.12 Parallelism:.12 / 3µm for models up to 3 / 75mm*.16 / 4µm for models over 3 / 75mm*.63 / 1.6µm for models up to 2 / 5mm** 2µm for models over 5mm** Measuring faces: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) / Digital model with ratchet stop Range Resolution Order No. Accuracy - 1"/ mm.5"/.1mm ±.15" 1-2"/ mm.5"/.1mm ±.15" 2-3"/ mm.5"/.1mm ±.15" 3-4"/ mm.5"/.1mm ±.2" DIMENSIONS AND MASS Analog models Unit: (up mm to 5mm) b L b L a a 27.5 Digital models (up to 75mm) b L a 27.5 b L a c ø8 ø21 c c ø14 c ø8 ø21 Analog models (over 5mm) Digital models (over 75mm) B-18

19 Outside Micrometers SERIES 17 Graduation:.1mm (thimble) Flatness:.6µm Parallelism: (2+R/1)µm, R=max. range (mm) Measuring faces: Carbide tipped Uses dial indicator for direct GO/NG-GO judgment for mass-produced parts. Anvil retracting trigger for quick measurement. Anvil retracting range: 3mm With a standard bar except for - 25mm models. Supplied in fitted plastic case. Dial indicator is an option Range Graduation Order No. Accuracy - 25mm.1mm ±2µm 25-5mm.1mm ±2µm 5-75mm.1mm ±2µm 75-1mm.1mm ±3µm 1-125mm.1mm ±3µm mm.1mm ±3µm mm.1mm ±4µm 175-2mm.1mm ±4µm DIMENSIONS AND MASS Dial indicator 28.5 L Lever a Range L a MASS (g) - 25mm mm mm mm mm mm mm mm B-19

20 Spline Micrometers SERIES 331, 111 IP65 water/dust protection (Series 331). The anvil and spindle have a small diameter for measuring splined shafts, slots, and keyways. With Ratchet Stop for constant force. With SPC output (Series 331). With a standard bar except -1 and -25mm model. Supplied in fitted plastic case Accuracy: Refer to the list of specifications. Resolution*:.5 /.1mm or.1mm Graduation**:.1 or.1mm,.1" Flatness:.12 /.3µm Parallelism: (2+R/1)µm, R=max. range (mm) [ (L/4 )] L = max. range (inch) Measuring faces: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Origin-set, Zero-setting, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Digital model Range Resolution Order No. Accuracy Remarks Mass (g) - 25mm.1mm ±2µm Type A ±2µm Type B mm.1mm ±2µm Type A ±2µm Type B mm.1mm ±2µm Type A ±2µm Type B mm ±3µm Type A 565 1mm ±3µm Type B 565 Range Graduation Order No. Accuracy Remarks Mass (g) - 25mm.1mm ±3µm Type A ±3µm Type B mm.1mm ±3µm Type A mm.1mm ±3µm Type A mm.1mm ±4µm Type A mm.1mm ±4µm Type A mm.1mm ±4µm Type A mm.1mm ±5µm Type A mm.1mm ±5µm Type A 14 / Digital model Range Resolution Order No. Accuracy Remarks Mass (g) - 1"/.5" / ±.1" Type A mm.1mm ±.1" Type B "/.5" / ±.1" Type A mm.1mm ±.1" Type B " /.5" / ±.1" Type A mm.1mm ±.1" Type B " /.5" / ±.15" Type A mm.1mm ±.15" Type B 565 Range Graduation Order No. Accuracy Remarks Mass (g) - 1".1" * ±.15" Type A 25 *.1" reading is obtained with vernier. Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) Type A (ø3mm) 1 1 ø3 Type B (ø2mm) 5 5 ø2 Models up to 75mm Models over 75mm b L a ø9.7 c b L a 37.5 ø9.7 C DIMENSIONS Digital model Digital model Range L a b c - 25mm 58.2 (55.3) 17.5 (17.8) 7.3 (1) 32 (38) 25-5mm 83.2 (8.3) 17.5 (17.8) 1.1 (12) 47 (49) 5-75mm 18.2 (15.3) 2.3 (17.8) 11.5 (14) 6 (6) 75-1mm (132.8) 2.3 (2.3) 16.7 (17) 76.5 (79) B-2

21 Point Micrometers SERIES 342, 142, 112 Accuracy: Refer to the list of specifications. Resolution*:.5"/.1mm or.1mm Graduation**:.1 or.1mm Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS, Data hold, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) IP65 water/dust protection (Series 342). Pointed spindle and anvil for measuring the web thickness of drills, small grooves, keyways, and other hard-to-reach dimensions. 15 degree and 3 degree measuring points are available. The measuring points have approximately.3mm /.12 radius. With Ratchet Stop for constant force. With SPC output (Series 342). With digit counter (Series 142). With a standard bar except - 1 and - 25mm model. Supplied in fitted plastic case Tip angle: 15 (R.3mm) Digital model (with carbide tip) Range Resolution Order No. Accuracy Point Mass (g) - 25mm.1mm ±2µm ±2µm mm.1mm ±2µm ±2µm mm.1mm ±2µm ±2µm mm.1mm ±3µm ±3µm / Digital model (with carbide tip) Range Resolution Order No. Accuracy Point Mass (g) - 1"/.5 / ±.1" mm.1mm ±.1" " - 2" /.5 / ±.1" mm.1mm ±.1" " - 3" /.5 / ±.1" mm.1mm ±.1" " - 4" /.5 / ±.15" mm.1mm ±.15" Tip angle: 3 (R.3mm) Mechanical Counter Model Range Graduation Order No. Accuracy Point Mass (g) - 25mm.1mm * ±3µm * ±3µm 3 26 *The points don't have carbide tips. Range Graduation Order No. Accuracy Point Mass (g) ±3µm mm.1mm * ±3µm ±3µm * ±3µm ±3µm mm.1mm * ±3µm ±3µm * ±3µm ±3µm mm.1mm * ±3µm ±3µm * ±3µm ±4µm mm.1mm * ±4µm ±4µm * ±4µm 3 5 *The points don't have carbide tips. Mechanical Counter Model Range Graduation Order No. Accuracy Point Mass (g) - 1".1" * ±.15" * ±.15" 3 26 *The points don't have carbide tips. Range Graduation Order No. Accuracy Point Mass (g) ±.15" ".1" * ±.15" ±.15" * ±.15" ±.15" ".1" * ±.15" ±.15" * ±.15" ".1" ±.15" *The points don't have carbide tips. B-21

22 DIMENSIONS Models up to 75mm b L a 45.7 c ø9.7 Models over 75mm b L a 42.5 ø c 15 3 Digital model Range L a b c d - 1 / - 25mm 58.2 (55.3) 12.5 (12.8) 7.3 (1) 32 (38) / 25-5mm 83.2 (8.3) 12.5 (12.8) 1.1 (12) 47 (49) / 5-75mm 18.2 (15.3) 12.5 (15.3) 11.5 (14) 6 (6) / 75-1mm (132.8) 15.3 (15.3) 16.7 (17) 76.5 (79) 6.35 ( ): Analog model Crimp Height Micrometers SERIES 342, 142, 112 Point Spindle and Blade Anvil Digital model IP54/65 water/dust protection (Series 342). Measures the height of crimp contacts. With Ratchet Stop for constant force. With SPC output (Series 342). With digit counter (Series 142). Supplied in fitted plastic case Quickmike type Accuracy: Refer to the list of specifications. Resolution*:.5" /.1mm or.1mm Graduation**:.1mm Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use (3 years: Quickmike type) Dust/Water protection level*: IP65 / IP54 *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS ( ), Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Digital model Range Resolution Order No. Accuracy Mass (g) - 2mm.1mm ±3µm 27 Quickmike type Range Resolution Order No. Accuracy Mass (g) - 15mm.1mm ±3µm 275 Mechanical counter model Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±3µm 2-25mm.1mm * ±3µm 2 *.1mm reading is obtained with vernier. / Digital model Range Resolution Order No. Accuracy Mass (g) -.8" / - 2mm.5.1mm / ±.15" 27 Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±3µm 165 Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m ) : SPC cable for Quickmike type (4 / 1m) 96513: SPC cable for Quickmike type (8 / 2m).5 (1) 6 (27 ) ø.5 (ø.6) ( ): for Series 142 B-22

23 V-Anvil Micrometers SERIES 314, Flutes and 5 Flutes Accuracy: Refer to the list of specifications. Resolution*:.5" /.1mm or.1mm Graduation**:.1" or.1",.1mm Flatness (spindle/anvil): Analog model:.24 /.6µm,.5 / 1.3µm Digital Model:.12" /.3µm,.4" / 1µm Spindle face: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use *Digital models **Analog models Function of Digital Model Zero / ABS, Data hold, Data output, Preset, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Function lock 2 Presets Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) Measures the outside diameter of cutting tools (such as taps, reamers, end mills) with an odd number of flutes. With Ratchet Stop for constant force. Supplied with setting standard. V-anvils with a centerline groove are available. They are useful for measuring pitch diameters of taps which have a small diameter by using single-wire method. With SPC output (Series 314). Supplied in fitted plastic case Pitch Diameter Measurement of Tap by Single-wire Method / Anvil Tap Wire Spindle Digital model for 3 flutes cutting head Range Resolution Order No. Accuracy Remarks Setting Standard Mass (g) 1-15mm.1mm ±4µm w/groove ø5mm ±4µm ø5mm mm.1mm ±4µm w/groove ø1mm ±4µm ø1mm mm.1mm ±5µm ø25mm 465 / Digital model for 3 flutes cutting head Range Resolution Order No. Accuracy Remarks Setting Standard Mass (g).5 -.6"/.5 / ±.2" w/groove ø.2" mm.1mm ±.2" ø.2" 275.4" - 1"/.5 / ±.2" w/groove ø.4" mm.1mm ±.2" ø.4" 41 1" - 1.6"/ mm.5 /.1mm ±.25" ø 1" 465 B-23

24 For 3 flutes cutting head Range Graduation Order No. Accuracy Setting Remarks Mass (g) Standard 1-15mm.1mm ±4µm ø5mm w/groove ±4µm ø5mm mm.1mm ±4µm ø1mm w/groove ±4µm ø1mm mm.1mm * ±4µm ø5mm mm.1mm ±5µm ø25mm mm.1mm ±6µm ø4mm mm.1mm ±6µm ø55mm mm.1mm ±7µm ø7mm 91 *Carbide-tipped anvil For 5 flutes cutting head Range Graduation Order No. Accuracy Setting Remarks Mass (g) Standard 5-25mm.1mm ±4µm ø5mm w/groove ±4µm ø5mm mm.1mm * ±4µm ø5mm mm.1mm ±5µm ø25mm mm.1mm ±6µm ø55mm mm.1mm ±7µm ø7mm 76 *Carbide-tipped anvil For 3 flutes cutting head Range Graduation Order No. Accuracy Setting Mass (g) Standard.5 -.6" ±.2" ø " * ±.2" ø " ±.25" ø " ±.3" ø *Carbide-tipped anvil and.1" reading is obtained with vernier For 5 flutes cutting head Range Graduation Order No. Accuracy Setting Standard Mass (g).9-1" ±.2" ø DIMENSIONS 8 (14.7) (a) ø1.5 w/o groove model 8 ø1.5 w/ groove model (14.5) (23.46) Range a / 1-25mm / 25-4mm / 4-55mm mm mm B-24

25 Limit Micrometers SERIES 113 Can be used as a GO/±NG gage by setting the upper and lower limits. Provided with a standard bar for 25mm - 5mm model. Supplied in fitted plastic case Graduation:.1mm Flatness:.6µm Parallelism: (3+R/1)µm, R=max. range (mm) Measuring faces: Carbide tipped Range Graduation Order No. Accuracy - 25mm.1mm ±3µm 25-5mm.1mm ±3µm DIMENSIONS AND MASS a L c C.5 (each spindle & anvil) Range L a c Mass (G) - 25mm mm B-25

26 Pana Micrometers SERIES 116 Interchangeable Anvil Type Non-rotating spindle with optional seven interchangeable anvils (flat, spline, spherical, point, knife-edge, disk, and blade) for a wide range of applications. Interchangeable anvils (pair) are optional. With a standard bar except -1 and - 25 mm model. V-anvils and conical spindle tips (matching pair) for screw thread measurement are also available. With Ratchet Stop for constant force. Graduation:.1 or.1mm Spindle feed error:.12 / 3µm Optional Accessories Interchangeable V-anvil and conical spindle tip set: For /Unified screw Order No. Assortment of anvils and tips mm/64-48TPI ( ).6 -.9mm/44-28TPI ( ) mm/24-14TPI ( ) 2-3mm/13-9TPI ( ) 3.5-5mm/8-5TPI ( ) 5.5-7mm/ TPI ( ) ø Interchangeable anvils set Order No. Assortment of anvils Flat anvils (116-81) Spline anvils (116-82) Spherical anvils (116-83) Point anvils (116-84) Knife-edge anvils (116-85) Disk anvils (116-86) Blade anvils (116-87) Shown with optional anvils Flat Spherical Knife-edge SR4 ø6 ø6.75 ø3.5 Spline Point Disk ø.3 ø2.4 ø11.1 ø4 ø6 Range Graduation Order No. Accuracy - 25mm.1mm ±4µm 25-5mm.1mm ±4µm Range Graduation Order No. Accuracy - 1".1" ±.2" 1" - 2".1" ±.2" Blade B-26

27 Spherical Face Micrometers SERIES 395, 295, 115 Accuracy: Refer to the list of specifications. Flatness:.24 /.6µm Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) IP65 water/dust protection (Series 395). Designed to measure the wall thickness of various tubing. With Ratchet Stop for constant force. With SPC output (Series 395). With digit counter (Series 295). With a standard bar except -1 and - 25mm model. Supplied in fitted plastic case Spherical anvil-spindle type SR4 ød SR4 Measuring faces: Carbide tipped ød: Mini. inside dia. of tubing Digital model with spherical anvil Range Resolution Order No. Accuracy Remarks Mass (g) - 25mm.1mm S-F ±2µm D: 15mm S-S ±2µm D: 15mm mm.1mm S-F ±2µm D: 15mm S-S ±2µm D: 15mm mm.1mm S-F ±2µm D: 19mm S-S ±2µm D: 19mm mm.1mm S-F ±3µm D: 2mm S-S ±3µm D: 2mm 625 S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle Mechanical counter model with spherical anvil Range Graduation Order No. Accuracy Remarks Mass (g) - 25mm.1mm S-F ±3µm D: 1mm S-S ±3µm D: 1mm 22 Digital model with / spherical anvil Range Resolution Order No. Accuracy Remarks Mass (g) - 1"/.5" / S-F ±.1" D:.59" mm.1mm S-S ±.1" D:.59" 27 1" - 2"/.5" / S-F ±.1" D:.59" mm.1mm S-S ±.1" D: " - 3"/ mm 3" - 4"/ mm.5" / S-F ±.1" D:.75" 47.1mm S-S ±.1" D:.75" 47.5" / S-F ±.15" D:.79" 625.1mm S-S ±.15" D:.79" 625 S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle Mechanical counter model with spherical anvil Range Graduation Order No. Accuracy Remarks Mass (g) - 1".1" S-F * ±.15" D:.4" S-S * ±.15" D:.4" 22 S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle *.1" reading is obtained with vernier. With spherical anvil Range Graduation Order No. Accuracy Remarks Mass (g) - 25mm.1mm S-F ±3µm D: 1mm S-S ±3µm D: 1mm mm.1mm S-F ±3µm D: 11mm S-S ±3µm D: 11mm mm.1mm S-F ±3µm D: 17mm S-S ±3µm D: 17mm mm.1mm S-F ±4µm D: 18mm S-S ±4µm D: 18mm 375 With spherical anvil Range Graduation Order No. Accuracy Remarks Mass (g) - 1".1" S-F * ±.15" D:.4" 18-1".1" S-S * ±.15" D:.4" ".1" S-S ±.15" D:.44" ".1" S-S ±.15" D:.67" 315 S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle *.1" reading is obtained with vernier. S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle B-27

28 Tube Micrometers SERIES 395, 295, 115 Spherical and Cylindrical Anvils IP65 water/dust protection (Series 395). Designed to measure the wall thickness of various tubing. The Tube Micrometers have two combinations of measuring faces (carbidetipped): spherical-flat type. Pin Anvil Type With Ratchet Stop for constant force. With SPC output (Series 395). With digit counter (Series 295). With a standard bar except -1" and - 25mm model. Supplied in fitted plastic case. Accuracy: Refer to the list of specifications. Flatness:.24 /.6µm Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) Type A Type B Digital model with cylindrical anvil Range Resolution Order No. Accuracy Remarks Mass (g) ±3µm Type A ±3µm Type B 27-25mm.1mm ±3µm Type C ±3µm Type D 31 Mechanical counter model Range Graduation Order No. Accuracy Remarks Mass (g) - 25mm.1mm ±3µm Type A 21 / Digital model with cylindrical anvil Range Resolution Order No. Accuracy Remarks Mass (g) - 1" / mm.5".1mm / ±.15" Type B ±.15" Type C ±.15" Type D 31 Mechanical counter model Range Graduation Order No. Accuracy Remarks Mass (g) ±.15" Type C 21-1".1" ±.15" Type D 21 Type C Type D With cylindrical anvil Range Graduation Order No. Accuracy Remarks Mass (g) ±3µm Type A 18-25mm.1mm ±3µm Type B ±3µm Type C ±3µm Type D mm.1mm ±3µm Type A ±3µm Type B 24 ø1.8 8 Type A (Pin) Sø3.5 6 Type B (Spherical) 12.7 Sø4.7 ø4 ø6.9 Type C (Spherical) 9 ø8 1.4 ø6.9 Type D (Cylindrical) L With cylindrical anvil Range Graduation Order No. Accuracy Remarks Mass (g).1" ±.15" Type A 18-1".1" * ±.15" Type C 18.1" * ±.15" Type D 18 *.1" reading is obtained with vernier. ød ød: Mini. inside dia. of tubing Spindle face: Carbide tipped Anvil D L Type A 2 4 Type B Type C Type D B-28

29 "Uni-Mike" SERIES 317, 117 Interchangeable Anvil Type Accuracy: Refer to the list of specifications. Resolution*:.5"/.1mm or.1mm Graduation**:.1 or.1mm Spindle face: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error IP65 water/dust protection (Series 317). Measures tubing thickness, shoulderedge distance, rivet head height, etc. with interchangeable anvils (flat anvil, rod anvil, V-anvil). Supplied with Flat Anvil (21216) and Rod Anvil:.118 /ø3mm dia. rod anvil (21217) for -1 /-25mm models,.197 /ø5mm (21379) for 1-2 / 25-5mm model. With special Disk Anvils. The Uni-Mike is used as a height micrometer. The disks have a lapped, mirror surface. With a standard bar except -1 and -25mm model. Supplied in fitted plastic case Optional Accessories 5CZA662: SPC cable with data switch (4 / 1m)* 5CZA663: SPC cable with data switch (8 / 2m)* 21218: V-anvil 95758: Disc. anvil for 1 / 25m models 95759: Disc. anvil for 2 / 5m models *Only for digital models Applications Digital model with ratchet stop Range Resolution Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm 36 Excluding quantizing error / Digital model with friction thimble Range Resolution Order No. Accuracy Mass (g) - 1" / mm.5" /.1mm ±.2" " / mm.5" /.1mm ±.2" 365 Excluding quantizing error Using flat anvil (21216) With ratchet stop Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm 32 DIMENSIONS (27.5) 25 () 27.5 With friction thimble Range Graduation Order No. Accuracy Mass (g) - 1".1" * ±.2" ".1" * ±.2" 32 *.1" reading is obtained with vernier ( ): for -25mm / -1 model 8.5 ø3 (21217) ø5 (21379) With the disc. anvil (95758) Shown above, the Uni-Mike is used as a height micrometer 25 Rod anvil (Standard accessory) V-anvil (Optional) (21218) Flat anvil (Standard accessory) (21216) B-29

30 Sheet Metal Micrometers SERIES 389, 119, 118 Measures thickness of sheet metal, paper, plastic, and rubber parts. With Ratchet Stop for constant force With a standard bar except for - 1 / - 25mm model. IP65 water/dust protection (Series 389*). *Except for / Supplied in fitted plastic case. DIMENSIONS a b Accuracy: Refer to the list of specifications. Resolution*:.5"/.1mm or.1mm Graduation**:.1mm,.1" or.1" Flatness:.24 /.6µm for models with 6 / 15mm throat.4 / 1µm for models with 12 / 3mm throat Parallelism:.12 / 3µm Measuring faces: Carbide tipped Display*: LCD Battery*: SR44 [1 pc. (2 pcs.: and )], Battery life*: Approx. 1.2 years under normal use (1.8 years: and ) Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Origin-set, Zero-setting, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m ) 5CZA663: SPC cable with data switch (8 / 2m) : SPC cable for / (4 / 1m) 96513: SPC cable for / (8 / 2m) Digital model Range Resolution Order No. Accuracy a/b - 25mm.1mm ±4µm 16/27.5mm - 25mm.1mm S-F ±4µm 16/27.5mm - 25mm.1mm S-S ±4µm 16/27.5mm - 25mm.1mm ±5µm 33/35mm 25-5mm.1mm ±4µm 165/27.5mm 25-5mm.1mm S-F ±4µm 165/27.5mm 25-5mm.1mm S-S ±4µm 165/27.5mm S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle / Digital model Range Resolution Order No. Accuracy a/b - 1" /.5" / ±.2" 6.3"/1.8" mm.1mm S-F ±.2" 6.3"/1.8" S-S ±.2" 6.3"/1.8" ±.25" 13"/1.38" 1-2" / mm.5" /.1mm S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle ±.2" 6.5"/1.8" S-F ±.2" 6.5"/1.8" S-S ±.2" 6.5"/1.8" Anvil-Spindle Combinations Standard, Flat-Flat Range Graduation Order No. Accuracy a/b - 25mm.1mm ±4µm 11/27.5mm - 25mm.1mm ±4µm 16/27.5mm - 25mm.1mm S-F ±4µm 16/27.5mm - 25mm.1mm S-S ±4µm 16/27.5mm - 25mm.1mm ±5µm 33/35mm 25-5mm.1mm ±4µm 165/27.5mm S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle Dial reading model Range Graduation Order No. Accuracy Throat - 25mm.1mm S-F ±4µm 5mm S-F: Spherical anvil and flat spindle Range Graduation Order No. Accuracy a/b - 1".1" ±.2" 6.3"/1.8" S-F ±.2" 6.3"/1.8" S-S ±.2" 6.3"/1.8".1" ±.25" 13"/1.38" 1" - 2".1" ±.2" 6.5"/1.8" S-F: Spherical anvil and flat spindle S-S: Spherical anvil and spherical spindle *.1" reading is obtained with vernier. DIMENSIONS AND MASS ø6.39 SR2 (Anvil) ø6 ø19 Spherical-Flat (S-F) Spherical-Spherical (S-S) The Series 119 is provided with a dial for making easy and quick reading B-3

31 Accuracy: Refer to the list of specifications. Resolution*:.5"/.1mm or.1mm Graduation**:.1" or.1mm Parallelism:.12 / 3µm for models up to 3 / 75mm (3+R/1)µm for models over 75mm, R=max. range (mm).16 for 4 models Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (1m / 4 ) 5CZA663: SPC cable with data switch (2m / 8 ) : SPC cable for Quickmike type (1m / 4 ) 96513: SPC cable for Quickmike type (2m / 8 ) Blade Micrometers SERIES 422,122 Non-Rotating Spindle Type The anvil and the spindle have a blade for measuring the groove diameter of shafts, keyways, and other hard-to-reach areas. With Ratchet Stop for constant force. Quickmike type Speedy spindle feed of.4 /1mm /rev. (Quickmike type). With a standard bar except - 1 and -25mm model. Supplied in fitted plastic case. TYPE AND DIMENSIONS ø6 R8.75 R ø ø6 Type A Type B ø6.75 ø Type C (carbide-tipped) Type D (carbide-tipped) Digital model Range Resolution Order No. Accuracy Remarks Mass (g) ±3µm Type A mm.1mm ±3µm Type B ±3µm Type C ±3µm Type D mm.1mm ±3µm Type A ±3µm Type B mm.1mm ±3µm Type A mm.1mm ±4µm Type A 58 Quickmike type Range Resolution Order No. Accuracy Mass (g) - 3mm.1mm ±3µm mm.1mm ±3µm 49 Range Graduation Order No. Accuracy Remarks Mass (g) ±3µm Type A 26-25mm.1mm ±3µm Type B ±3µm Type C ±3µm Type D ±3µm Type A mm.1mm ±3µm Type B ±3µm Type C ±3µm Type D mm.1mm ±3µm Type A mm.1mm ±4µm Type A mm.1mm ±4µm Type A mm.1mm ±4µm Type A mm.1mm ±5µm Type A mm.1mm ±5µm Type A 114 / Digital model Range Resolution Order Accuracy Remarks Mass (g) No ±.15" Type A 365-1" /.5" / ±.15" Type B mm.1mm ±.15" Type C ±.15" Type D " / mm 2-3" / mm 3-4" / mm.5" /.1mm.5" /.1mm.5" /.1mm ±.15" Type A ±.15" Type B ±.15" Type A ±.2" Type A 58 / Quickmike type Range Resolution Order No. Accuracy Remarks Mass (g) - 1.2" /.5" / ±.15" Type A mm.1mm 1-2.2" / mm.5" /.1mm ±.15" Type A 49 Range Graduation Order No. Accuracy Remarks Mass (g) ±.15" Type A 26-1".1" ±.15" Type B ±.15" Type D ".1" ±.15" Type A 3 2-3".1" ±.15" Type A ".1" ±.2" Type A 525 B-31

32 Disk Micrometers SERIES 323, 223, Rotating Spindle Diameter of measuring disk:.787 / 2mm.28 /.7mm (1mm: models over 1mm) edge thickness to enter narrow recesses. With Ratchet Stop for constant force With a standard bar except for - 1 / - 25mm model. With SPC output (Series 323). The Series 223 is provided with a mechanical digit counter for quick reading of measurements. Supplied in fitted plastic case. (Over 1mm models supplied wooden cases) Accuracy: Refer to the list of specifications. Resolution*:.5 /.1mm or.1mm Graduation**:.1 or.1mm Flatness:.4 / 1µm for models up to.4 /1mm.63 / 1.6µm for models over 4 / 1mm Parallelism:.16 / 4µm for models up to 2 / 5mm.24 for models up to 4 (4+R/5)µm for models up to 1mm (5+R/75)µm for models over 1mm, R=max. range (mm) Measurable module:.5-6 (.7-11: models over 1mm) Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use *Digital models **Analog models Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) Digital model Range Resolution Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±6µm mm.1mm ±6µm 61 Mechanical counter model Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm 29 Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm * ±4µm mm.1mm ±4µm * ±4µm mm.1mm ±6µm * ±6µm mm.1mm ±6µm * ±6µm mm.1mm ±7µm mm.1mm ±7µm mm.1mm ±8µm mm.1mm ±8µm mm.1mm ±8µm mm.1mm ±9µm mm.1mm ±9µm mm.1mm ±9µm 168 *The measuring disks have carbide tips. Note: The disk diameter of models over 1mm is 3mm. / Range Digital model Resolution Order No. Accuracy Mass (g) - 1"/ mm.5"/.1mm ±.2" "/ mm.5"/.1mm ±.2" "/5-76.2mm.5"/.1mm ±.3" "/ mm.5"/.1mm ±.3" 61 Mechanical counter model Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.2" 26 Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.2" 2 1-2".1" ±.2" ".1" ±.3" 3 3-4".1" ±.3" 375 Root tangent length of gear (En) En Note: Root tangent length measurement is not available for some types of gears. B-32

33 DIMENSIONS Digital models up to 75mm b L Analog models up to 5mm b L a 35.2 a 31.5 Digital models up to 75mm b L Analog over 5mm b L a 32 a ø14.3 c c c c Range L a b c ød øe t - 1" / - 25mm 37.5 (39.7) 6 (4.5) 14 (9.2) 25 (25.4) 2 8 (9.8).7 1-2" / 25-5mm 62.5 (65.6) 6 (5.4) 14 (11) 32 (31.9) 2 8 (9.8).7 2-3" / 5-75mm 87 (9.7) 5.5 (5.5) 11 (12.2) 49 (5) 2 8 (9.8).7 3-4" / 75-1mm 112 (112.5) 5.5 (5.5) 11 (13.5) 63 (6.5) 2 8 (9.8).7 4-5" / 1-125mm " / mm " / mm " / 175-2mm " / 2-225mm " / mm " / mm " / 275-3mm Data in ( ) applies to those with carbide tipped disks. t ød øe Center concavity Graduation:.1 or.1mm Flatness:.4 / 1µm Parallelism:.12 / 3µm Measuring Force: 8.2 ±.8N 53.9KPa ±4.9 KPa Paper Thickness Micrometers SERIES 169 Non-Rotating Spindle Type Designed for Paper Thickness Measurement Non-rotating spindle. With Ratchet Stop for constant force. Supplied in fitted plastic case. DIMENSIONS ø8.4 ø14.3 (ø.44 ) ( ): model Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm 23g Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.2" 23g B-33

34 Disk Micrometers SERIES 369, 227, 169 Non-Rotating Spindle Type The Disk Micrometer is designed to easily measure root tangent length of spur gears and helical gears. Non-rotating spindle eliminates torque on workpiece. With standard bar except - 15mm, mm, - 1, - 3mm & model Speedy spindle feed of 1mm/rev. (Quickmike type). Diameter of measuring disk:.787 / 2mm With Ratchet Stop for constant force. With SPC output (Series 369). Supplied in fitted plastic case Quickmike type Accuracy: Refer to the list of specifications. Resolution*:.5"/.1mm or.1mm Graduation**:.1 or.1mm Flatness:.4 / 1µm Parallelism: 4µm /.16 for models up to 2 / 5mm 6µm /.24 for models over 2 / 5mm Measurable module:.5-6 Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use (1 year: Quickmike type, 3 years: Quickmike type with fine-loading) Series 227: Refer to page B-6 for more information. *Digital models **Analog models Quickmike type with adjustable measuring force Function of Digital Model Origin-set, Zero / ABS, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (4 / 1m) 5CZA663: SPC cable with data switch (8 / 2m) : SPC cable for Quickmike type (4 / 1m) 96513: SPC cable for Quickmike type (8 / 2m) Digital model Range Resolution Order No. Accuracy - 25mm.1mm ±4µm 25-5mm.1mm ±4µm 5-75mm.1mm ±6µm 75-1mm.1mm ±6µm Quickmike type Range Resolution Order No. Accuracy - 3mm.1mm ±4µm 25-55mm.1mm ±4µm / Range Digital model Resolution Order No. Accuracy - 1" / mm.5" /.1mm ±.2" 1-2" / mm.5" /.1mm ±.2" 2-3" / mm.5" /.1mm ±.3" 3-4" / mm.5" /.1mm ±.3" / Range Quickmike type Resolution Order No. Accuracy - 1.2" / mm.5" /.1mm ±.2" 1-2.2" / mm.5" /.1mm ±.2" Quickmike type with adjustable measuring force Range Resolution Order No. Accuracy Measuring force - 1mm.1mm ±4µm 2N - 1N - 15mm.1mm ±4µm.5N - 2.5N Range Graduation Order No. Accuracy - 25mm.1mm ±4µm 25-5mm.1mm ±4µm 5-75mm.1mm ±6µm 75-1mm.1mm ±6µm Range Graduation Order No. Accuracy - 1".1" ±.2" 1-2".1" ±.2" 2-3".1" ±.3" 3-4".1" ±.3" B-34

35 DIMENSIONS AND MASS Digital models up to 75mm b L a c ø Adjustable measuring force type ø14.3 ø24.9 ø Digital models over 75mm b L 14.5 a Analog models up to 5mm b L b 31.5 Quickmike type b a L Analog models over 5mm c c c c ø24.9 ø8 ø b a 31.5 L (.4) ø2 (ø14.3) ø8 ( ): Adjustable measuring force type Digital model Range L a b c Mass (g) - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" mm* / - 1.2" mm* / 1-2.2" *Quickmike type Analog model Range L a b c Mass (g) - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" B-35

36 Gear Tooth Micrometers SERIES 324, 124 Interchangeable Ball Anvil-Spindle Tip Type IP65 water/dust protection (Series 324). Measures over-pin diameter of gears with precision steel (carbide) ball-tipped measuring faces. With a standard bar except - 25mm and - 1 model Interchangeable ball anvil-spindle tips for various gear modules ( ) are optional. With Ratchet Stop for constant force. With SPC output (Series 324). Supplied in fitted plastic case (Models over 15mm have wooden case) Shown with optional ball anvils Accuracy: Refer to the list of specifications. Resolution*:.1mm or.5"/.1mm Graduation**:.1mm Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Zero / ABS, Data hold, Data output, Preset, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Function Lock 2 Presets Optional Accessories 5CZA662: SPC cable with data switch (1m / 4 )* 5CZA663: SPC cable with data switch (2m / 8 )* *Only for digital models Shown with optional ball anvils Digital model Range Resolution Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±5µm 6 / Range Digital model Resolution Order No. Accuracy Mass (g) - 1"/ - 25mm.5 /.1mm ±.2" 4 1-2"/25-5mm.5 /.1mm ±.2" "/5-75mm.5 /.1mm ±.2" "/75-1mm.5 /.1mm ±.25" 6 Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±5µm mm.1mm ±5µm mm.1mm ±5µm mm.1mm ±6µm mm.1mm ±6µm mm.1mm ±6µm mm.1mm ±7µm mm.1mm ±7µm mm.1mm ±7µm 27 DIMENSIONS AND MASS Range L a Mass (g) 18 L mm (28) 27.5 (35) (28) (5) 25-5mm 5-75mm mm mm mm mm mm mm mm mm ( ): 275-3mm model 275-3mm a (ø8) (ø21) Interchangeable ball anvil-spindle tip set: Diameter of ball anvil Order No. Gear module Diametral pitch.8mm * mm * mm (3/64") * mm * mm (1/16") * mm * mm (3/32") mm mm mm (1/8") mm mm (5/32") mm mm mm (3/16") mm mm (7/32") mm mm (1/4") mm mm (9/32") mm (5/16") mm mm (11/32") *Carbide-tipped type B-36

37 Screw Thread Micrometers SERIES 125 Provided with a 6 degree V-anvil and conical spindle for easily measuring pitch diameters of metric or unified screw threads. With Ratchet Stop for constant force. With a standard bar for zero point adjustment except - 25mm model. Supplied in fitted plastic case Accuracy: ±(2+R/75)µm, R=max. range (mm) Graduation:.1mm Spindle feed error: 3µm Range Graduation Order No. Screw to be measured (/Unified) - 25mm.1mm mm/64-48TPI mm/44-28TPI mm/24-14TPI mm/13-9TPI mm/8-5TPI 25-5mm.1mm mm/64-48TPI mm/44-28TPI mm/24-14TPI mm/13-9TPI mm/8-5TPI 5-75mm.1mm mm/44-28TPI mm/24-14TPI mm/13-9TPI mm/8-5TPI mm/ TPI 75-1mm.1mm mm/44-28TPI mm/24-14TPI mm/13-9TPI mm/8-5TPI mm/ TPI DIMENSIONS AND MASS 18 L a L a Range L a Mass (g) - 25mm mm mm mm B-37

38 Screw Thread Micrometers SERIES 326, 126 Interchangeable Anvil-Spindle Tip Type IP65 water/dust protection (Series 326). 6 degree or 55 degree V-anvil and conical spindle (interchangeable) are optional, which are made of high-grade steel, hardened and precision ground. With Ratchet Stop for constant force. With SPC output (Series 326). With a standard bar except - 25mm and - 1 model. Supplied in fitted plastic case Shown with optional anvils Resolution*:.1mm or.5"/.1mm Graduation**:.1mm or.1" Spindle feed error: 3µm /.12 Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use Dust/Water protection level*: IP65 *Digital models **Analog models Function of Digital Model Zero / ABS, Data hold, Data output, 2 Presets, Function Lock. inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Digital model Range Resolution Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±5µm / Range Digital model Resolution Order No. Accuracy Mass (g) - 1" / mm.5" /.1mm ±.2" " / mm.5" /.1mm ±.2" " / mm.5" /.1mm ±.2" " / mm.5" /.1mm ±.25" 51 Optional Accessories 5CZA662: SPC cable with data switch (1m / 4 )* 5CZA663: SPC cable with data switch (2m / 8 )* *Only for digital models (See page B-51.): Standard for screw thread micrometer Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±4µm mm.1mm ±5µm mm.1mm ±5µm mm.1mm ±5µm mm.1mm ±6µm mm.1mm ±6µm mm.1mm ±6µm 1, mm.1mm ±7µm 1, mm.1mm ±7µm 1, mm.1mm ±7µm 1,54 DIMENSIONS 18 L Throat depth a B-38 Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.2" ".1" ±.2" ".1" ±.2" ".1" ±.25" ".1" ±.25" ".1" ±.25" ".1" ±.3" 73 With anvil set (126-8) Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.2" ".1" ±.2" ".1" ±.2" ".1" ±.25" ".1" ±.25" ".1" ±.25" 62 Range L a - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" mm / 4-5" mm / 5-6" mm / 6-7" mm / 7-8" mm / 8-9" mm / 9-1" mm / 1-11" mm / 11-12" Anvil-spindle tip set: Applications Screw, Unified screw (6 threads) Whitworth Screw (55 threads) Set Order No Tip Information Threads Per Individual Pitch (mm) Order No (M1) (M2) (M3) (M4) (M5) (M6) Features: 6 degree or 55 degree V-anvil and conical spindle (interchangeable) are optional, which are made of high-grade special steel, hardened and precision ground Storage Box Included

39 3-Wire Thread Measuring System Individual Holder and Wire Set Fast and accurate method of thread measuring available for use with Micrometer Wire holders and 3 thread measuring wires assembled for each thread pitch PD M Vertically, Adjustable Platform for positioning and supporting threaded parts and plug gages between anvil of micrometer Micrometer with a graduation of.5" P.D. = Pitch Diameter M = Measurement over wires W = Wire diameter C = Constant C =.8663 x Pitch (inches) -3W P.D. = M-C W = x P Applications Measure set of thread plug gages and working thread plug gages Monitor the wear on working thread plug gages Monitor and control pitch diameter variation during thread fabrication Reduce measurement time to a fraction of the time normally taken using the traditional three wire method Use in conjunction with Go and No Go thread ring gages to control thread size to the most demanding specifications Determine out of roundness and taper that may exist in threaded parts Applications for preplating and post plating thread measurement Tolerance of Wires: Diameter +/-.1 Roundness +/-.1 Surface finish 2 micro inches AA, lapped. Hardness HRC Certification of accuracy included. Traceable to NIST. Meets or exceeds all ANSI and ISO specs. W Order No. Base Assembly INCH STANDARD HOLDERS AND WIRES SETS Threads Per 64AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA AAA Thread Measuring Wire Diameter Compatible with Micrometers with.25 Anvils & Spindles Stand Assembly Order No Locking clamp holds micrometer securely in place METRIC HOLDERS AND WIRES SETS Order No. Pitch mm Diameter Diameter 64AAA251.2mm AAA mm AAA253.25mm AAA254.3mm AAA255.35mm AAA256.4mm AAA257.45mm AAA258.5mm AAA259.55mm AAA26.6mm AAA261.7mm AAA262.75mm AAA263.8mm AAA264.85mm AAA265.9mm AAA266 1.mm AAA mm AAA mm AAA mm AAA27 2.mm AAA mm AAA272 3.mm AAA mm AAA274 4.mm B-39

40 Can Seam Micrometers SERIES 147 Measures the width, height, and depth of can seams. Three types of micrometers are available for: steel cans, aluminum cans, and sprayer cans. Supplied in fitted carton. Accuracy: ±.12 / ±3µm Graduation:.1 /.1mm Range Graduation Order No. Remarks for steel cans - 13mm.1mm for aluminum cans for sprayer cans Range Graduation Order No. Remarks -.5".1" for steel cans for aluminum cans for sprayer cans for cans (for depth measurements up to 5mm) DIMENSIONS AND MASS for aluminium cans ø2 ø15 MASS: 65g ø ø15 MASS: 65g for sprayer cans ø ø MASS: 65g B-4

41 Accuracy: Refer to the list of specifications. Graduation:.1mm /.1 Flatness:.6µm /.24 Parallelism: (2+R/1)µm, R=max. range (mm) [ (L/4)], L = Max. range (inch). Measuring faces: Carbide tipped Hub Micrometers SERIES 147 Measures hub thickness and shoulders inside a bore. With Ratchet Stop for constant force. With a standard bar except for - 1 / - 25mm model. Supplied in fitted plastic case h H h1 Range Graduation Order No. Accuracy - 25mm.1mm ±2µm 25-5mm.1mm ±2µm 5-75mm.1mm ±2µm 75-1mm.1mm ±3µm Wire Micrometers SERIES 147 Designed for measuring wire thickness. Also used to measure the diameter of a small ball. Supplied in fitted plastic case. Range Graduation Order No. Accuracy - 1".1" ±.1" 1-2".1" ±.1" 2-3".1" ±.1" 3-4".1" ±.15" Range Graduation Order No. Accuracy Mass (g) - 1mm.1mm ±3µm Range Graduation Order No. Accuracy Mass (g) -.4".1" * ±.15" 65 *.1 reading is obtained with vernier ø ø15 h2 Range h1 h2 h3 H Mass (g) - 1" / - 25mm " / 25-5mm " / 5-75mm " / 75-1mm Graduation:.1 or.1mm Flatness:.24 /.6µm Parallelism:.5 / 1.3µm Measuring faces: Carbide tipped DIMENSIONS AND MASS MASS = 65g B-41

42 Digital Outside Micrometers SERIES 193 Mechanical digit counter with.1mm or.1" reading for quick and error-free reading. With a standard bar except for -25mm / -1 model. Supplied in fitted plastic case. Counter reading:.1mm or.1" Graduation:.1mm,.1mm,.1" or.1" Flatness:.6µm /.24 Parallelism: (2+R/1)µm, R=max. range (mm) [ (L/4)], L= max. range (inch) Measuring faces: Carbide tipped With ratchet stop Range Graduation Order No. Accuracy - 25mm.1mm ±2µm.1mm * ±2µm 25-5mm.1mm ±2µm.1mm * ±2µm 5-75mm.1mm ±2µm.1mm * ±2µm 75-1mm.1mm ±3µm.1mm * ±3µm *.1mm reading is obtained with vernier. Micrometer sets Range Order No. Included in set - 75mm (3 pcs./set) , , micrometer standards - 75mm (3 pcs./set) , , , 2 micrometer standards - 1mm (4 pcs./set) , , , micrometer standards - 1mm (4 pcs./set) , , , micrometer standards With friction thimble Range Graduation Order No. Accuracy.1" ±.1" - 1".1" * ±.1" 1-2".1" * ±.1" *.1" reading is obtained with vernier. With ratchet stop Range Graduation Order No. Accuracy 2-3".1" * ±.1" 3-4".1" * ±.15" *.1" reading is obtained with vernier. Micrometer sets Range Order No. Included in set - 3" (3 pcs./set) , , micrometer standards DIMENSIONS AND MASS Models up to 1mm / 4 b L a 27.5 c Range L a b c Mass (g) - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" Note: The shape of the thimble changes on the model with Friction Thimble. B-42

43 Spindle feed error: 3µm /.12 Dial indication accuracy: 1µm /.4 Dispersion of indication:.4µm /.2 Graduation:.1mm or.1" Dial reading:.1mm or.5" Flatness:.3µm /.12 Parallelism:.6µm /.24 for models up to 5mm / 2 1µm /.4 for models over 5mm / 2 Measuring force: 5-1N (5-1gf) Measuring faces: Carbide tipped Optional Accessories 4AZA124: ø16mm / ø.63 workpiece stopper (not available for 25mm / 1 model) 4AZA125: ø14mm / ø.55" workpiece stopper 4AZA126: ø14mm / ø.55" workpiece stopper a Indicating Micrometers SERIES 51 Retractable anvil with indicator for threewire measurements of pitch diameter of precision screws and parallelism measurements. With a standard bar except for - 25mm / - 1 model. IP protection level: 54 Supplied in fitted plastic case b 4 DIMENSIONS AND MASS L a b 4AZA AZA AZA Range Graduation Order No. Indicating range - 25mm.1mm * ±.6mm mm.1mm ±.6mm 5-75mm.1mm ±.6mm 75-1mm.1mm ±.6mm *Retractable anvil button on the right side. Range Graduation Order No. Indicating range - 1".5" * ±.23" ".5" ±.23" 2-3".5" ±.23" 3-4".5" ±.23" *Retractable anvil button on the right side mm.1 6 d ø8 ø21 Snap Meters SERIES 523 Various types of indicators, LVDT s and Linear Gages can be selected according to the measurement applications. Supplied in fitted plastic case. Indicator is optional L ø16 Retractable anvil button Workpiece stopper (optional) Range L d Mass (g) - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" Flatness:.3µm /.12 Parallelism:.6µm /.24 for models up to 5mm / 2 1µm /.4 for models over 5mm / 2 Measuring force: 5-1N (5-1gf) Measuring faces: Carbide tipped DIMENSIONS AND MASS ø1.8 d Range d L Mass (g) - 25mm / - 1" mm / 1-2" mm / 2-3" mm / 3-4" Gage stem dia 8mm Gage stem dia 3/8" Range Order No. Anvil movement Range Order No. Anvil movement - 25mm mm - 1" " 25-5mm mm 1-2" " 5-75mm mm 2-3" " 75-1mm mm 3-4" " B-43

44 Dial Snap Meters SERIES 523 Direct GO/NO-GO judgment for mass-produced parts. Spindle diameter:.425 / 1.8mm IP protection level: 54 Supplied in fitted plastic case. Dial indication accuracy:.5 / 1µm Indication repeatability:.2 /.4µm Dial reading:.5 or.1mm Flatness: Parallelism:.12 /.3µm.24 /.6µm for models up to 2 / 5mm.4 / 1µm for models over 2 / 5mm Measuring force: 5-1N (5-1gf) Measuring faces: Carbide tipped Range Graduation Order No. Indicating range - 25mm.1mm ±.6mm 25-5mm.1mm ±.6mm 5-75mm.1mm ±.6mm 75-1mm.1mm ±.6mm Range Graduation Order No. Indicating range - 1".5" ±.23" 1-2".5" ±.23" 2-3".5" ±.23" 3-4".5" ±.23" DIMENSIONS AND MASS 89.5 L ø1.8 d Range ( / ) d L Mass (g) - 1" / - 25mm " / 25-5mm " / 5-75mm " / 75-1mm B-44

45 Accuracy: Refer to the list of specifications. Resolution*:.1mm or.5"/.1mm Graduation**:.1mm /.1 Flatness:.3µm /.12 Parallelism: (3+R/75)µm, R=max. range (mm) [ (L/8)] L = Max, range (inch) Measuring faces: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), Battery life*: Approx. 1.2 years under normal use *Digital models **Analog models Function of Digital Model Origin-set, Zero-setting, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories for Digital Model 5CZA662: SPC cable with data switch (1m / 4 ) 5CZA663: SPC cable with data switch (2m / 8 ) Caliper Type Micrometers SERIES 343, 143 With Ratchet Stop for constant force. With SPC output (Series 343). With a standard bar except - 25mm and - 1 model. Supplied in fitted plastic case Digital model Range Resolution Order No. Accuracy Mass (g) - 25mm.1mm ±5µm mm.1mm ±6µm mm.1mm ±7µm mm.1mm ±8µm 19 / Range Digital model Resolution Order No. Accuracy Mass (g) - 1" / mm.5" /.1mm ±.25" " / mm.5" /.1mm ±.3" " / mm.5" /.1mm ±.35" " / mm.5" /.1mm ±.4" 19 Range Graduation Order No. Accuracy Mass (g) - 25mm.1mm ±5µm mm.1mm ±6µm mm.1mm ±7µm mm.1mm ±8µm 33 Models with a range up to 3mm are available. Range Graduation Order No. Accuracy Mass (g) - 1".1" ±.25" ".1" ±.3" ".1" ±.35" 28 DIMENSIONS Unit = mm L 14 a Thickness 3 b L b a Thickness φ 13 φ φ 8 φ φ 4 φ φ 6.35 φ 18 B-45

46 Groove Micrometers SERIES 146 Flanged spindle for measuring width, depth, and location of grooves inside/ outside bores, and tubes. Provided with two types of graduations for inside and outside measurements. Non-rotating spindle type has twodirectional ratchet stop. (Measuring force:.7-1.2n) Rotating spindle type Range Outside Range Inside Graduation Order No. Flange Mass (g) - 25mm mm.1mm mm ø12.7mm mm mm.1mm ø12.7mm mm mm.1mm ø12.7mm mm mm.1mm ø12.7mm 16 Rotating spindle type Range Outside Range Inside Graduation Order No. Flange Mass (g) - 1".55" - 1.5".1" ø.25" ø.5" 185 1" - 2" 1.5" - 2.5".1" ø.5" 175 2" - 3" 2.5" - 3.5".1" ø.5" 165 3" - 4" 3.5" - 4.5".1" ø.5" 16 Non-rotating spindle type Range Outside Range Inside Graduation Order No. Flange Mass (g) - 25mm mm.1mm mm ø12.7mm mm mm.1mm ø12.7mm mm mm.1mm ø12.7mm mm mm.1mm ø12.7mm 16 Non-rotating spindle type Range Outside Range Inside Graduation Order No. Flange Mass (g) - 1".55" - 1.5".1" ø.25" ø.5" 185 1" - 2" 1.5" - 2.5".1" ø.5" 175 2" - 3" 2.5" - 3.5".1" ø.5" 165 3" - 4" 3.5" - 4.5".1" ø.5" 16 DIMENSIONS ø3.5 ø5 ø1 ø (35) (.25 )*.75 (.25 )* (17) Anvil Thickness of Model (.25 *) Accuracy: ±.4 / ±1µm Parallelism:.4 / 1µm ø12.7 ø12.7 ø1 ø (13.3) (.25 )*.75 (.25 )* (228.8) ø3.5 ø5 ø1 ø (34.5) (.25 )*.75 (.25 )* (179.5) ø12.7 ø12.7 ø1 ø (115) (.25 )*.75 (.25 )* (24.5) B-46

47 Small Hole Gage Set SERIES 154 Used with an outside micrometer for measuring inside diameter of bores. 4 sizes of gages are supplied in a fitted pouch. Extra long for gaging deep and shallow holes, slots, and similar workpieces. Gaging surface is fully hardened to insure long tool life. DIMENSIONS b Clamp L b L 67 a DIMENSIONS c Order No. L a b / / / / Clamp a Order No. L a b c / / / / / / Total range Set Order No. Assortment of gages ø3-13mm (4-gage set) ø3-5mm gage (154-11) ø5-7.5mm gage (154-12) ø7.5-1mm gage (154-13) ø1-13mm gage (154-14) Telescoping Gage Set SERIES 155 Spring-loaded plunger expands within the bore (or groove), allowing determination of the internal diameter (or groove width). With a knurled clamp. Supplied in a fitted pouch. Total range Set Order No. Included in set 8-15mm (6-gage set) mm gage ( ) mm gage ( ) 19-32mm gage ( ) 32-54mm gage (155-13) 54-9mm gage ( ) 9-15mm gage ( ) Total range Set Order No. Assortment of gages " " -.2" DIA. gage (154-15) DIA..2" -.3" DIA. gage (154-16) (4-gage set).3" -.4" DIA. gage (154-17).4" -.5" DIA. gage (154-18) Total range.313-6" (6-gage set).5-6" (5-gage set) " (4-gage set) Set Order No. Included in set " -.5" gage ( ).5" -.75" gage ( ).75" " gage ( ) 1.25" " gage ( ) 2.125" - 3.5" gage ( ) 3.5" - 6" gage ( ) , , , , , , , B-47

48 Micrometer Stands SERIES 156 These stands are designed to allow benchtop use with hand micrometers or other gages Micrometer ranges Order No. Remarks -1 / -25mm, Fixed angle type 1-2 / 25-5mm Up to 4 / 1mm Adjustable angle type 5-12 / 125-3mm Vertical type 12-4 / 3-1mm Vertical type -1 / -25mm 1-2 / 25-5mm Fixed angle with platform DIMENSIONS 4 to 12 ø ø to to B-48

49 Color Ratchet & Color Speeder Color ratchet Color speeder for Ratchet Thimble Micrometer Tip length: metric type: 1mm ±5µm inch type:.5" ±.2" Spindle Dia: *1.25 / 6.35mm *1 Spindle diameter for (.25" ball) is.315"/ 8mm Order No. Color Black Red Blue Yellow Green Brown 4GZA241* Gray 4GZA239** Gray 4GZA243*** Gray *for Series 293 digital model ** up to 3mm / 12 ** over 3mm / 12 Order No. 4GAA899 4GAA9 4GAA91 4GAA92 4GAA93 4AAB28 Spindle Attachment Tip Color Black Red Yellow Green Blue Gray Ball Spline Comparator Blade Knife-edge Disk (.2" ball dia.) (.25" ball dia.) 2862* * * * * 2812 DIMENSIONS Order No. Dimension Order No. Dimension To measure odd workpieces, several convenient anvil attachments are prepared by MITUTOYO. Among them the most often used one is the ball attachment. The ball attachments are hardened steel balls with.2 and.25 diameters which are placed on the.25 and.315 diameter anvils, respectively, by rubber caps. With these attachments, regular micrometers can measure cylindrical wall thickness, but,.2 or.25 must be subtracted from the readings. Other attachments shown here are either.5 or 1mm in length. The added amount must be subtracted from the reading * * * ø ø2 ø * * * metric type 3.5 ø12.7 Micrometer Oil 27 (3ml) B-49

50 Optical Parallels SERIES 157 Designed to inspect parallelism and flatness of measuring faces of micrometers. Each set consists of 4 thicknesses. Supplied in fitted wooden case. Flatness:.4 /.1µm Parallelism:.8 /.2µm Diameter: 1.18 / 3mm Parallelism Check between Measuring Faces by Means of Interference Fringe Produced by an Optical Parallel The parallelism between the measuring faces can be determined as follows; place the optical parallel to the anvil and observe the number of interference fringes produced on the spindle side under the measuring force of the micrometers. The parallelism is about 1µm (.32µm x 3 =.96µm). Fringe on the anvil side must not be more than one. Viewing direction of the spindle Viewing direction of the anvil Spindle Optical parallel Anvil Range of micrometer to be checked Order No. Assortment of parallels (Thickness of parallel) -25mm mm (157-11) 12.12mm (157-12) 12.25mm (157-13) 12.37mm (157-14) 25-5mm mm (157-15) 25.12mm (157-16) 25.25mm (157-17) 25.37mm (157-18) Optical Flats SERIES 158 Used for inspecting the flatness of micrometer's or gage block's measuring faces with high accuracy. Range of micrometer to be checked Order No. Assortment of parallels (Thickness of parallel) -1" " (157-19).562" (157-11).5125" ( ).5187" ( ) 1-2" " ( ) 1.62" ( ) 1.125" ( ) 1.187" ( ) Supplied in fitted wooden case. Flatness Check of Measuring Faces Using Interference Fringe Pattern Produced by an Optical Flat Viewing direction Optical flat Anvil Optical flat Anvil Flatness Order No. Diameter/Thickness.2µm mm/12mm mm/15mm.1µm mm/12mm mm/15mm Flatness Order No. Diameter/Thickness.4" "/.5" "/.6" B-5

51 Flatness:.3µm /.12 Parallelism: 2µm /.8 Micrometer Standards SERIES 167 Used for the zero point setting of outside micrometers. Flat and lapped measuring faces. Heat insulating handle to prevent expansion due to body temperature. Supplied in fitted carton up to 5mm / 2 and wooden case for over 525mm / 21, length Length (L) Order No. Diameter (D) Accuracy Micrometer Standards Set Order No. Size Remarks * pcs. Set ( , 142, 143, 144, 145) * pcs. Set ( , 142, 143, 144,145, 146, 147, 148, 149, 15, 151) Order No. Size Remarks * mm 5 pcs. Set (167-11, 12, 13, 14, 15) * mm 11 pcs. Set (167-11, 12, 13, 14, 15, 16, 17, 18, 19, 11, 111) *Supplied with fitted carrying case DIMENSION D 12.7 D ø13 25mm - 75mm / 1-3 2mm - 475mm / 8-19 Length (L) Order No. Diameter (D) Accuracy 25mm mm ±1.5µm 5mm mm ±2.µm 75mm mm ±2.5µm 1mm mm ±3µm 125mm mm ±3.5µm 15mm mm ±4µm 175mm mm ±4.5µm 2mm mm ±5.µm 225mm mm ±5.5µm 25mm mm ±6.µm 275mm mm ±6.5µm 3mm mm ±7µm 325mm mm ±7.5µm 35mm mm ±8µm 375mm mm ±8.5µm 4mm mm ±9µm 425mm mm ±9.5µm 45mm mm ±1.µm 475mm mm ±1.5µm 5mm mm ±11µm 525mm mm ±11.5µm 55mm mm ±12µm 575mm mm ±12.5µm 6mm mm ±13µm 625mm mm ±13.5µm 65mm mm ±14µm 675mm mm ±14.5µm 7mm mm ±15µm 725mm mm ±15.5µm 75mm mm ±16µm 775mm mm ±16.5µm 8mm mm ±17µm 825mm mm ±17.5µm 85mm mm ±18µm 875mm mm ±18.5µm 9mm mm ±19µm 925mm mm ±19.5µm 95mm mm ±2µm 975mm mm ±2.5µm 1mm mm ±21µm L L 11 D 1mm - 175mm / 4-7 5mm - 1mm / 2-4 D ø14 ø17 L L Length (L) Order No. Diameter (D) Accuracy 1" " ±.5 2" " ±.1 3" " ±.1 4" " ±.1 5" " ±.15 6" " ±.15 7" " ±.15 8" " ±.15 9" " ±.2 1" " ±.2 11" " ±.2 12" " ±.25 13" " ±.25 14" " ±.25 15" " ±.25 16" " ±.25 17" " ±.25 18" " ±.25 19" " ±.3 2" " ±.3 21" " ±.3 22" " ±.3 23" " ±.3 24" " ±.3 25" " ±.35 26" " ±.35 27" " ±.35 28" " ±.35 29" " ±.35 3" " ±.35 31" " ±.35 32" " ±.35 33" " ±.35 34" " ±.35 35" " ±.35 36" " ±.35 37" " ±.4 38" " ±.4 39" " ±.4 4" " ±.4 B-51

52 Standards for Screw Thread Micrometers SERIES degree and 55 degree Specially designed for the zero point setting of screw thread micrometers. Supplied in fitted carton. Thread angle: 55 or 6 Angle Accuracy: ± (6 ) Length Order No. Thread angle Accuracy 25mm ±4µm ±4µm 5mm ±5µm ±5µm 75mm ±6µm ±6µm 1mm ±7µm ±7µm 125mm ±8µm ±8µm 15mm ±9µm ±9µm 175mm ±1µm ±1µm 2mm ±11µm ±11µm 225mm ±12µm ±12µm 25mm ±13µm ±13µm 275mm ±14µm ±14µm (6 ) Length Order No. Thread angle Accuracy 1" ± ±.15 2" ± ±.2 3" ± ±.25 4" ± ± ±.35" ±.35" ±.4" ±.4" Standards for V-Anvil Micrometers SERIES 167 Specially designed for the zero point setting of V-anvil micrometers. Supplied in fitted carton. ø25mm Diameter Order No. Type Accuracy 5mm Plug ±2µm 1mm Plug ±2µm 25mm Plug ±2µm 4mm Ring ±3µm 55mm Ring ±3µm 7mm Ring ±3µm 85mm Ring ±3µm Diameter Order No. Type Accuracy.2" Plug ±.1.4" Plug ±.1 1" Plug ±.1 1.6" Ring ± " Ring ± " Ring ± " Ring ±.15 B-52

53 Tool Kits The Digimatic Tool Kits include Mitutoyo s highly popular 1 / 25mm Digimatic Micrometer (choose ratchet or friction type) and 6 / 15mm Digimatic Caliper with Absolute Encoder. The case is made of handsome, solid mahogany and has space for gage batteries. The micrometer spanner is a supplied accessory. Order No. 64PKA68 ( Tool Kit) Item No. Description Outside Micrometer (Friction Thimble Type) (Range: 1, Graduation:.1 ) Dial Caliper (Range: 6, Dial Graduation:.1 ) Full-Flexible Rule (3R) 64PPP932 Mahogany Case 64PKA68 Order No. 64PKA69 ( Tool Kit) Item No. Description Outside Micrometer (Friction Thimble Type) (Range: 1, Graduation:.1 ) Full-Flexible Rule (16R) T Test Indicator Set (Range:.4, Graduation:.1 ) Dial Caliper (Range: 6, Dial Graduation:.1 ) 551 Mahogany Case The very basic measuring instruments recommended for vocational students and machinist apprentices are supplied in this kit. 64PKA69 Order No. 64PKA7 ( Tool Kit) Item No. Description Outside Micrometer (Friction Thimble Type) (Range: 1, Graduation:.1 ) Depth Micrometer (with 6 pcs Rods) (Range: 6, Graduation:.1 ) Full-Flexible Rule (16R) Dial Caliper (Range: 6, Graduation:.1 ) 553 Mahogany Case For operations where depth measurements are a primary concern, this kit is ideal for measuring depths to 6, in addition to providing the tools for regular precision measurements. Order No. 64PKA71A ( Tool Kit) Item No. Description Outside Micrometer Set (3 pcs) (Range: 3, Graduation:.1 ) Inside Micrometer (with 6 pcs Rods) 18-95B Combination Set (4R) Full-Flexible Rule (16R) T Test Indicator Set (Range:.4, Graduation:.1 ) Dial Caliper (Range: 6, Dial Graduation:.1 ) 2416S Dial Indicator (Range: 1., Graduation:.1 ) 71S Magnetic Stand 554 Mahogany Case Most every routine inspection assignment can be completed with the eight high-quality MITUTOYO Precision Measuring Instruments provided in this deluxe kit. 64PKA7 64PKA71A B-53

54 Tool Kits Order No. 64PKA8A ( Tool Kit) Item No. Description " Steel Rule (16R) Micrometer (Ratchet Thimble) (Range -1, Graduation.1 ) Dial Caliper (Range: 6, Dial Graduation:.1 ) 64PPP932 Mahogany Case 64PKA8A Order No. 64PKA73B (Tool Kit Lite) Item No. Description " Steel Rule (16R) " / - 15mm MyCal Lite (Resolution:.1" /.1mm) " / mm MDC Lite (Ratchet Stop) (Resolution:.5" /.1mm) 64PPP932 Mahogany Case 64PKA73B Order No. 64PKA76B (Digimatic Tool Kit) Item No. Description Digimatic Micrometer (Ratchet Stop Type) (Range: - 1" / mm, LCD Resolution:.5" /.1mm) Digimatic Caliper with Absolute Encoder (Range: - 6" / - 15mm, LCD Resolution:.5" /.1mm) 64PPP932 Mahogany Case 64PKA76B Order No.64PKA77B (Digimatic Tool Kit) Item No. Description Digimatic Micrometer (Friction Thimble Type) (Range: - 1" / mm, LCD Resolution:.5" /.1mm) Digimatic Caliper with Absolute Encoder (Range: - 6" / - 15mm, LCD Resolution:.5" /.1mm) 64PPP932 Mahogany Case 64PKA77B B-54

55 Micrometer Head Selection Guide Variety of Specifications With clamp nut Spindle lock Spherical face type Reverse reading type The table below provides an outline of Mitutoyo micrometer heads for each series so you can locate the pages to refer to select the micrometer head most appropriate to your specific application. When selecting consider the following points: Dimensions Graduation/resolution and accuracy With or without spindle lock With or without clamping nut Normal or reverse reading With or without Ratchet Stop SELECTION TABLE Range Series Remarks Page - 1mm 11 Differential screw translator (extra-fine feeding) type B mm 11 Differential screw translator (extra-fine feeding) type B-69-5mm 148 Ultra small type B-6-6.5mm 148 Fine spindle feeding of.1mm/rev. B Fine spindle feeding of.25mm/rev. B Small type B Large thimble diameter for easy reading B-61-1mm 152 Fine feeding type B-68-13mm 148 Common type in small size B Spindle feeding of.25mm/rev. B Zero-adjustable thimble type B Large thimble diameter for easy reading B Differential screw translator (extra-fine feeding) type B-69-15mm 149 with carbide-tipped spindle type B Non-rotating spindle type B Quick spindle feeding of 1mm/rev. B-68-25mm 164 Digital type B Compact digital type B Common type in middle size B Non-rotating spindle type B Fine graduation type B Heavy duty type (ø8mm spindle) B Quick spindle feeding of 1mm/rev. B Fine feeding type B for XY-stage B High resolution and high accuracy type B with digit counter type B-73-5mm 164 Digital type B Heavy duty type (ø8mm spindle) B Quick spindle feeding of 1mm/rev. B Fine feeding type B Non-rotating spindle and large thimble B-71 B-55

56 Digimatic Micrometer Heads SERIES 164 The Digimatic Micrometer Heads... The display can be rotated up to 33 for easy reading in any position. Accuracy: Refer to the list of specifications. Range Order No. Accuracy Mass (g) - 5mm ±3µm / Range Order No. Accuracy Mass (g) - 2" / - 5.8mm ±.15" 49 Resolution:.1mm or.5"/.1mm Display: LCD Battery: SR44 (2 pcs.), Battery life: 1.8 years: Function Zero-setting, Data hold, Data output, Preset, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories : SPC cable (1m / 4 ) 95915: SPC cable (2m / 8 ) DIMENSIONS 2 (29) ф8 ф11 ф49 ф PRESET / B-56

57 Non-rotating device , The non-rotating device provides no radial torsion on the workpiece surface so that workpiece wear and deformation are minimized. ø8 ø11 5CZA662: SPC cable with data switch (29) (1m / 4") 42 (17) 15 ø49 / Range Order No. Stem Spindle face Stem dia. Remarks - 1" / -25.4mm Plain Flat (carbide tip).375" M12x " / -25.4mm w/ clamp nut Flat (carbide tip).375" - 1" / -25.4mm Plain Spherical (SR4).375" 4-1" / -25.4mm w/ clamp nut Spherical (SR4) " " / -25.4mm Plain (17) (139.5) Flat (carbide tip).5" IP65 (139.5) M9.5x " / -25.4mm w/ clamp nut Flat (carbide tip).5" IP65-1" / -25.4mm Plain Spherical (SR4).5" IP , " / -25.4mm w/ clamp nut Spherical (SR4).5" IP , " / -25.4mm * Plain Flat.5" IP *with non-rotating device and 18mm stem bushing. 42 (17) 15 Stem Dia (139.5) , , B Digimatic Micrometer Heads SERIES 35 Equipped With Digital display and output. 35 series IP65 models: the Digimatic output port enables inclusion in a statistical process control or networked measurement system. Measuring force: 5-1N Accuracy* ±2µm model ±.1" / model Resolution:.1mm or.5"/.1mm Display: LCD Battery: SR44 (1 pc) Battery life: Approx. 3 years under normal use Dust/Water protection level: IP , , , , , , , , SR4 SR4 ø16 M12x Function Preset, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Function Lock 2 Presets Optional Accessories 5CZA663: SPC cable with data switch (2m / 8") 64PPP35: Stem Bushing (.375" ID/.79" OD) DIMENSIONS AND MASS M12x ø12 (58) ø8 ø (16) / ø (29) Range Order No. Stem Spindle face Stem dia. Remarks - 25mm Plain Flat (carbide tip) 1mm - 25mm w/ clamp nut Flat (carbide tip) 1mm - 25mm Plain Spherical (SR4) 1mm - 25mm w/ clamp nut Spherical (SR4) 1mm / mm Plain Flat (carbide tip) 12mm IP65-25mm w/ clamp nut Flat (carbide tip) 12mm IP65-25mm Plain Spherical (SR4) 12mm IP65-25mm w/ clamp nut Spherical (SR4) 4212mm IP65-25mm * Plain (17) (139.5) Flat 12mm IP65 M12x.5 15 *with non-rotating device and 18mm stem bushing. SR4 SR4 SR4 SR4 ø16 (58) ø , , ø12 Stem Dia. A ø49 (58) (58) , , Mass: 23g SR4 SR4 ø14 M9.5x , , , , Mass: 23g 14 ø (1.5) 1 ø , (11) (27.7) (126) 14 ø (58) Mass: 235g ø

58 Micrometer Heads SERIES 148 Fine Spindle Feeding of.1mm/rev Fine spindle feeding of just.1mm/rev for extra-fine adjustment and positioning. External dimensions are compatible with conventional.5mm pitch heads. Graduations:.2mm Spindle pitch:.1mm Spindle face: Spherical of SKS3 (more than HRC6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm ( : 4mm) Spindle pitch Screw Thread pitch=.1mm Screw Thread pitch=.5mm Range Order No mm mm mm mm mm mm DIMENSIONS AND MASS Accuracy Stem dia. Stem Spindle face Remarks ±2µm 9.5mm Plain Spherical (SR4) ±2µm 9.5mm w/clamp nut Spherical (SR4) ±2µm 9.5mm Plain Spherical (SR4) Thicker & shorter thimble ±2µm 9.5mm w/clamp nut Spherical (SR4) Thicker & shorter thimble ±5µm 6mm Plain Spherical (SR3) Small thimble diameter ±5µm 6mm w/clamp nut Spherical (SR3) Small thimble diameter Applications Semiconductor wafer positioning machinery and optical component alignment units, etc. Precision X-Y table positioning Precision adjustment of mirror in holder SR4 ø SR4 ø14 4 ø ø5 ø3.5 SR4 SR3 9.5 (17) 23.5 ø (38) (17) Mass: 31g Mass: 34g (12) (3) Mass: 29g Mass: 31g ø6 ø ø9.3 ø15 6 M6x (8.5) 21.9 (8.5) (28.4) 15 (28.4) Mass: 1g Mass: 1g ø5 M9.5x.5 M9.5x.5 8 ø3.5 SR4 SR3 ø ø9.5 ø ø9.3 ø (12) (3) (38) ø15 ( ): when retracting the spindle until its stroke end. Comparison of mounting dimensions between a standard fine-pitch head and a standard conventional pitch head at the mid-range travel position (55) 2.5 Scale: 3mm position (Operating range) Fine-pitch head (spindle pitch:.1mm) 13 (Operating range) Scale: 6.5mm position (58.5) Conventional pitch head (spindle pitch:.5mm) While the fine-pitch micrometer head has a measuring range of 6.5mm, the conventional head has a larger range of 13mm. When replacing a conventional head, the fine-pitch type can use the common range in the middle of the spindle travel. The standard and compact types of fine-pitch head are completely interchangeable. B-58

59 Micrometer Heads SERIES 148 Fine Spindle Feeding of.25 mm / rev Graduations:.1mm Spindle pitch:.25mm Spindle face: Spherical of SKS3 (more than HRC6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm Fine spindle feeding of just.25mm/rev for fine adjustment and positioning Range Order No. - 13mm mm mm mm Accuracy Stem dia. Stem Spindle face 2µm 9.5mm Plain Spherical (SR4) 2µm 9.5mm w/clamp nut Spherical (SR4) 2µm 9.5mm Plain Spherical (SR4) 2µm 9.5mm w/ clamp nut Spherical (SR4) DIMENSIONS AND MASS ø5 SR4 ø SR4 ø ø13 ø (14) (44.5) g (12) (3) g ø5 SR4 ø14 4 ø SR4 ø14 4 ø ø13 ø15 M9.5x (14) (44.5) g M9.5x.5 (12) (3) g ( ): when retracting the spindle until its stroke end. B-59

60 Micrometer Heads SERIES 148 Ultra-Small/Small Type Miniature micrometer heads for ease of incorporating into machines. Graduations:.2mm ( , ),.1mm or.1" Spindle pitch:.5mm Spindle face: Flat or spherical of SKS3 (more than HRC6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 3mm ( , ), 4mm Range Order No. - 5mm mm mm mm mm mm mm mm Accuracy Stem dia. Stem Spindle face Remarks ±5µm 3.5mm Plain Spherical (SR1.5) ±5µm 3.5mm w/clamp nut Spherical (SR1.5) ±5µm 6mm Plain Flat ±5µm 6mm w/clamp nut Flat ±5µm 6mm Plain Spherical (SR3) ±5µm 6mm w/clamp nut Spherical (SR3) ±5µm 6mm Plain Flat Reverse reading ±5µm 6mm w/ clamp nut Flat Reverse reading Shown actual size Range Order No. Accuracy Stem dia. Stem Spindle face Remarks -.2" ±5µm.156" Plain Spherical (SR1.5) -.2" ±5µm.156" w/clamp nut Spherical (SR1.5) -.25" ±5µm.25" Plain Flat -.25" ±5µm.25" w/clamp nut Flat -.25" ±5µm.25" Plain Spherical (SR3) -.25" ±5µm.25" w/clamp nut Spherical (SR3).25 - " ±5µm.25" Plain Flat Reverse reading.25 - " ±5µm.25" w/ clamp nut Flat Reverse reading DIMENSIONS AND MASS SR ( Model) ø ( Model) SR M4.x.5 ( Model) M3.5x.5 ( Model) ø2 ø6 5 (6.5) (25.5) ø3.5 3 ø9.3 ø2 ø6 5 (6.5) (25.5) / Mass: 4g / Mass: 4g ø ( Model) ø6 -.8 ( Model).25 ( Model) ø6 -.8 ( Model) ø (8.5) 22 (28.5) / Mass: 1g 7.5 M6x.5 (8.5) (28.5) / Mass: 1g ( ): when retracting the spindle until its stroke end. B-6

61 ø14 Micrometer Heads SERIES 148 Large Thimble Diameter for Easy Reading Easy reading due to the large thimble diameter. (Three types of thimble diameters can be selected.) Range Order No. Accuracy Stem dia. Stem Spindle face Thimble Dia mm ±2µm 9.5mm Plain Flat 15mm - 6.5mm ±2µm 9.5mm w/clamp nut Flat 15mm - 6.5mm ±2µm 9.5mm Plain Flat 2mm - 6.5mm ±2µm 9.5mm w/clamp nut Flat 2mm - 6.5mm ±2µm 9.5mm Plain Flat 29mm - 6.5mm ±2µm 9.5mm w/clamp nut Flat 29mm - 13mm ±2µm 9.5mm Plain Flat 15mm - 13mm ±2µm 9.5mm w/clamp nut Flat 15mm - 13mm ±2µm 9.5mm Plain Flat 2mm - 13mm ±2µm 9.5mm w/clamp nut Flat 2mm - 13mm ±2µm 9.5mm Plain Flat 29mm - 13mm ±2µm 9.5mm w/ clamp nut Flat 29mm Range Order No. Accuracy Stem dia. Stem Spindle face Thimble Dia. -.25" ±.1".375" Plain Flat.59" -.25" ±.1".375" w/clamp nut Flat.59" -.25" ±.1".375" Plain Flat.79" -.25" ±.1".375" w/clamp nut Flat.79" -.25" ±.1".375" Plain Flat 1.14" -.25" ±.1".375" w/clamp nut Flat 1.14" -.5" ±.1".375" Plain Flat.59" -.5" ±.1".375" w/clamp nut Flat.59" -.5" ±.1".375" Plain Flat.79" -.5" ±.1".375" w/clamp nut Flat.79" -.5" ±.1".375" Plain Flat 1.14" -.5" ±.1".375" w/ clamp nut Flat 1.14" DIMENSIONS AND MASS Graduations:.1mm or.1 Spindle pitch:.5mm or.25 Spindle face: Flat of SKS3 (more than HRC6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm (12) ø12 ø (3) M9.5.5 ø (12) ø12 ø (3) ø2 ø () () ø / g.375 () () ø / g.375 () ø ().375 () ø () 9.5 (12) (3) / g M9.5x (12) 3 25 (43) / g ( ): when retracting the spindle until its stroke end. B-61

62 Micrometer Heads SERIES 148 Common Type in Small Size Range Order No. Accuracy Stem dia. - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm - 13mm ±2µm 9.5mm 13mm ±2µm 9.5mm 13mm ±2µm 9.5mm 13mm ±2µm 9.5mm 13mm ±2µm 9.5mm *with spindle lock Stem Spindle face Remarks Plain Flat w/clamp nut Flat Plain* Flat w/clamp nut* Flat Plain Spherical (SR4) w/clamp nut Spherical (SR4) Plain* Spherical (SR4) w/clamp nut* Spherical (SR4) Plain Flat Reverse reading w/clamp nut Flat Reverse reading Plain* Flat Reverse reading w/ clamp nut* Flat Reverse reading Range Order No. Accuracy Stem dia. Stem Spindle face Remarks -.5" ±.1".375" Plain Flat -.5" ±.1".375" w/clamp nut Flat -.5" ±.1".375" Plain* Flat -.5" ±.1".375" w/clamp nut* Flat -.5" ±.1".375" Plain Spherical (SR4) -.5" ±.1".375" w/clamp nut Spherical (SR4) -.5" ±.1".375" Plain* Spherical (SR4) -.5" ±.1".375" w/clamp nut* Spherical (SR4).5" ±.1".375" Plain Flat Reverse reading.5" ±.1".375" w/clamp nut Flat Reverse reading.5" ±.1".375" Plain* Flat Reverse reading.5" ±.1".375" w/ clamp nut* Flat Reverse reading *with spindle lock DIMENSIONS AND MASS () () ø ø5 ø (14) (44.5) / g ø5 ø13 ø () ø () ø5 ø M9.5x.5 (14) (44.5) / g Graduations:.1mm or.1" Spindle pitch:.5mm Spindle face: Flat or spherical of SKS3 (more than HR6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm.375 () ø () ø15 4 ø5 ø () ø () ø15 ø (14) (53.1) / g M9.5x.5 (14) (53.1) / g ( ): when retracting the spindle until its stroke end. B-62

63 Micrometer Heads SERIES 148 Common Type in Small Size with Zero-Adjustable Thimble The thimble can be set to zero at any position by loosening the setscrew Range Order No. - 13mm mm mm mm mm mm mm mm mm *with spindle lock Accuracy Stem dia. Stem Spindle face Remarks ±2µm 9.5mm Plain Flat ±2µm 9.5mm Plain Flat Stainless steel throughout ±2µm 9.5mm w/clamp nut Flat ±2µm 9.5mm Plain* Flat ±2µm 9.5mm w/clamp nut* Flat ±2µm 9.5mm Plain Spherical (SR4) ±2µm 9.5mm w/clamp nut* Spherical (SR4) ±2µm 9.5mm Plain Flat Reverse reading ±2µm 9.5mm w/ clamp nut* Flat Reverse reading Graduations:.1mm or.1" Spindle pitch:.5mm Spindle face: Flat or spherical of SKS3 (more than HRC6), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm Range Order No. Accuracy Stem dia. Stem Spindle face Remarks -.5" ±.1".375" Plain Flat -.5" ±.1".375" Plain Flat Stainless steel throughout -.5" ±.1".375" w/clamp nut Flat -.5" ±.1".375" Plain* Flat -.5" ±.1".375" w/clamp nut* Flat -.5" ±.1".375" Plain Spherical (SR4) -.5" ±.1".375" w/clamp nut* Spherical (SR4).5" ±.1".375" Plain Flat Reverse reading.5" ±.1".375" w/ clamp nut* Flat Reverse reading *with spindle lock DIMENSIONS AND MASS.375 () () ø () ø () ø14 ø5 ø13 ø5 ø (12) (5) / g 9.5 M9.5x.5 (12) (5) / g.375 () ø () ø15 4 ø5 ø13 ø () () ø15 ø ø5 ø (12) 45.6 M9.5x (12) (58.6) 25 (58.6) / g / g ( ): when retracting the spindle until its stroke end. B-63

64 Micrometer Heads SERIES 149 Common Type in Small Size with Carbide-Tipped Spindle Carbide tipped measuring face. Range Order No. - 15mm mm mm mm mm mm mm mm *with spindle lock. Accuracy Stem dia. Stem Spindle face Remarks ±2µm 9.5mm Plain Flat (carbide tip) ±2µm 9.5mm w/clamp nut Flat (carbide tip) ±2µm 9.5mm Plain* Flat (carbide tip) With spindle lock ±2µm 9.5mm w/clamp nut* Flat (carbide tip) With spindle lock ±2µm 9.5mm Plain Spherical (SR4) ±2µm 9.5mm w/clamp nut Spherical (SR4) ±2µm 9.5mm Plain Flat (carbide tip) Reverse reading ±2µm 9.5mm w/ clamp nut Flat (carbide tip) Reverse reading Range Order No. Accuracy Stem dia. Stem Spindle face Remarks -.5" ±.1".375" Plain Flat (carbide tip) -.5" ±.1".375" w/clamp nut Flat (carbide tip) -.5" ±.1".375" Plain* Flat (carbide tip) With spindle lock -.5" ±.1".375" w/clamp nut* Flat (carbide tip) With spindle lock -.5" ±.1".375" Plain Spherical (SR4) -.5" ±.1".375" w/clamp nut Spherical (SR4).5" ±.1".375" Plain Flat (carbide tip) Reverse reading.5" ±.1".375" w/ clamp nut Flat (carbide tip) Reverse reading *with spindle lock DIMENSIONS AND MASS (17).375 () ø () ø (58.5) / g M9.5x.5 ø (17).375 () () ø ø ø15 ø15 ø15 (58.5) / g Graduations:.1mm or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip (more than HRA9) or spherical, lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 6mm ( , : 11.5mm).375 () () ø ø15 ø () () ø (11.5) (64) 3.5 M9.5x (11.5) (64) / g / g ( ): when retracting the spindle until its stroke end. B-64

65 Graduations:.1mm,.1mm,.1" or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip* (more than HRA9) or spherical, lapped surface *Long spindle type: SKS3 (more than HRC6) Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 11.5mm Micrometer Heads SERIES 15 Common Type in Middle Size Ratchet stop for constant force. Long spindle type is available for a variety of applications. Carbide tipped measuring face. Range Order No. - 25mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm *with spindle lock Accuracy Stem dia. Stem Spindle face Remarks ±2µm 1mm Plain Flat (carbide tip) ±2µm 1mm w/clamp nut Flat (carbide tip) ±2µm 1mm Plain* Flat (carbide tip) ±2µm 1mm w/clamp nut* Flat (carbide tip) ±2µm 1mm Plain Spherical (SR4) ±2µm 1mm w/clamp nut Spherical (SR4) ±2µm 1mm Plain Flat (carbide tip) Reverse reading ±2µm 1mm w/clamp nut Flat (carbide tip) Reverse reading ±2µm 1mm Plain Flat (carbide tip) w/ vernier (.1mm) ±2µm 1mm w/clamp nut Flat (carbide tip) w/ vernier (.1mm) ±2µm 1mm Plain* Flat (carbide tip) w/ vernier (.1mm) ±2µm 1mm w/clamp nut* Flat (carbide tip) w/ vernier (.1mm) ±2µm 1mm Plain* Flat (carbide tip) w/o ratchet stop ±2µm 1mm w/clamp nut* Flat (carbide tip) w/o ratchet stop ±2µm 1mm Plain Flat Long spindle ±2µm 1mm w/ clamp nut Flat Long spindle Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 1" ±.1".375" Plain Flat (carbide tip) - 1" ±.1".375" Plain Flat (carbide tip) w/o ratchet stop - 1" ±.1".375" w/clamp nut Flat (carbide tip) - 1" ±.1".375" w/clamp nut Flat (carbide tip) w/o ratchet stop - 1" ±.1".375" Plain* Flat (carbide tip) - 1" ±.1".375" w/clamp nut* Flat (carbide tip) - 1" ±.1".375" Plain Spherical (SR4) - 1" ±.1".375" w/clamp nut Spherical (SR4) - 1" ±.1".375" Plain Flat (carbide tip) Reverse reading - 1" ±.1".375" w/clamp nut Flat (carbide tip) Reverse reading - 1" ±.1".375" Plain Flat (carbide tip) w/ vernier (.1") - 1" ±.1".375" w/clamp nut Flat (carbide tip) w/ vernier (.1") - 1" ±.1".375" Plain* Flat (carbide tip) w/ vernier (.1") - 1" ±.1".375" w/clamp nut* Flat (carbide tip) w/ vernier (.1") - 1" ±.1".375" Plain* Flat (carbide tip) w/o ratchet stop - 1" ±.1".375" w/clamp nut* Flat (carbide tip) w/o ratchet stop - 1" ±.1".375" Plain Flat Long spindle - 1" ±.1".375" w/ clamp nut Flat Long spindle *with spindle lock DIMENSIONS AND MASS.375 () ø1 -.9 () 4 15 (17) (92) ø2 ø () ø1 -.9 () M9.5x.5 (17) (92) / g / g.375 () ø1 -.9 () ø () ø1 -.9 () ø (17) (13.5) / g M9.5x (17) (13.5) / g ( ): when retracting the spindle until its stroke end. B-65

66 Micrometer Heads SERIES 151 Common Type in Middle Size with 8mm Diameter Spindle 8mm diameter spindle for heavy duty use. Ratchet stop for constant force. Carbide tipped measuring face. Range Order No. - 25mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm *with spindle lock Accuracy Stem dia. Stem Spindle face Remarks ±2µm 12mm Plain Flat (carbide tip) ±2µm 12mm w/clamp nut Flat (carbide tip) ±2µm 12mm Plain* Flat (carbide tip) ±2µm 12mm w/clamp nut* Flat (carbide tip) ±2µm 12mm Plain Flat (carbide tip) w/ vernier (.1mm) ±2µm 12mm w/clamp nut Flat (carbide tip) w/ vernier (.1mm) ±2µm 12mm Plain* Flat (carbide tip) w/ vernier (.1mm) ±2µm 12mm w/clamp nut* Flat (carbide tip) w/ vernier (.1mm) ±2µm 12mm Plain Flat (carbide tip) w/o ratchet stop ±2µm 12mm w/clamp nut Flat (carbide tip) w/o ratchet stop ±2µm 12mm Plain* Flat (carbide tip) w/o ratchet stop ±2µm 12mm w/clamp nut* Flat (carbide tip) w/o ratchet stop ±4µm 12mm Plain Flat (carbide tip) ±4µm 12mm w/clamp nut Flat (carbide tip) ±4µm 12mm Plain Flat (carbide tip) w/o ratchet stop ±4µm 12mm w/ clamp nut Flat (carbide tip) w/o ratchet stop Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 1" ±.1".5" Plain Flat (carbide tip) - 1" ±.1".5" w/clamp nut Flat (carbide tip) - 1" ±.1".5" Plain Flat (carbide tip) w/ vernier (.1") - 1" ±.1".5" w/clamp nut Flat (carbide tip) w/ vernier (.1") - 1" ** ±.1".5" Plain* Flat (carbide tip) w/ vernier (.1") - 1" ** ±.1".5" w/clamp nut* Flat (carbide tip) w/ vernier (.1") - 1" ±.1".5" Plain* Flat (carbide tip) w/o ratchet stop - 1" ±.1".5" w/clamp nut* Flat (carbide tip) w/o ratchet stop - 2" ±.2".5" Plain Flat (carbide tip) - 2" ±.2".5" w/clamp nut Flat (carbide tip) *with spindle lock **with ratchet stop DIMENSIONS AND MASS Graduations:.1mm,.1mm,.1" or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 25.5mm ø8.5 () ø () ø8.5 () () ø ø8.5 () () ø ø21 ø21 ø22 ø21 29 (38) (38) (28.6) (95) 88 (153) 53.6 (9.9) / g / g / g ø8 ø16 ø21 4 ø21 ø8 ø () () ø () () ø ø22 ø21 ø8 ø () () ø M12x M12x.5 (38) 7 (38) (95) 88 (153) M12x (28.6) (9.9) / g / g / g ( ): when retracting the spindle until its stroke end. B-66

67 Micrometer Heads SERIES 153 Non-Rotating Spindle Type Carbide tipped measuring face. Non-rotating spindle Range Order No. - 15mm mm * - 25mm * - 25mm mm *with ratchet stop Accuracy Stem dia. Stem Spindle face Remarks ±3µm 9.5mm Plain Flat (carbide tip) w/ vernier (.1mm) ±3µm 12mm Plain Flat (carbide tip) ±3µm 12mm Plain Flat (carbide tip) w/ vernier (.1mm) ±3µm 12mm Plain Flat (carbide tip) ±3µm 12mm Plain Flat (carbide tip) w/ vernier (.1mm) Range Order No. Accuracy Stem dia. Stem Spindle face Remarks -.5" ±.15".375" Plain Flat (carbide tip) w/ vernier (.1") - 1" * ±.15".5" Plain Flat (carbide tip) - 1" * ±.15".5" Plain Flat (carbide tip) w/ vernier (.1") - 1" ±.15".5" Plain Flat (carbide tip) - 1" ±.15".5" Plain Flat (carbide tip) w/ vernier (.1") *with ratchet stop Graduations:.1mm,.1mm,.1" or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: Hard-chrome plating DIMENSIONS AND MASS.375 () () ø15.3 ø ø14.8 ø8 ø (12).5 ().5 () ø () () ø (12) ø14.8 ø (73.5) / g Ratchet stop 87.5 (112.5) / g 37 1 (12) 7.5 (95.5) / g ( ): when retracting the spindle until its stroke end. B-67

68 Micrometer Heads SERIES 152 Quick Spindle Feeding of 1mm/rev. Quick spindle feeding of 1mm/rev. Carbide tipped measuring face. Graduations:.1mm Spindle pitch: 1mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: Hard-chrome plating Range Order No. - 15mm mm mm Accuracy Stem dia. Stem Spindle face Remarks ±2µm 12mm Plain Flat (carbide tip) ±2µm 12mm Plain Flat (carbide tip) ±4µm 12mm Plain Flat (carbide tip) DIMENSIONS AND MASS ø8.5 () A () ø (19) B ø3 ( ): when retracting the spindle until its stroke end. C Micrometer Heads SERIES 152 Large Thimble Type for Fine Feeding The large diameter thimble for fine adjustment and positioning. Carbide tipped measuring face. Range Order No. - 1mm mm mm mm DIMENSIONS AND MASS Range A B C Mass (g) - 15mm mm mm Accuracy Stem dia. Stem Spindle face Remarks ±2µm 12mm w/clamp nut Flat (carbide tip) ±2µm 12mm Plain Flat (carbide tip) ±2µm 12mm Plain Flat (carbide tip) Bidirectional graduation ±4µm 12mm Plain Flat (carbide tip) Bidirectional graduation Graduations:.2mm or.1" Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 1" ±.1".5" Plain Flat (carbide tip) Bidirectional graduation - 2" ±.2".5" Plain Flat (carbide tip) Bidirectional graduation Spindle pitch: 1mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: White anodized aluminum Fixture thickness for clamp nut: 22.5mm ø16.5 () () ø ø8 ø49 ø49.5 () () ø M12x (35) (63) (38) 66 (91) / / B-68

69 Micrometer Heads SERIES 11 Differential Screw Translator (Extra-Fine Feeding) Type Differential movements of spindle threads and units allow fine spindle feeding (.5mm/rev*), resulting in high resolution measurements. *11-52, 11-54:.25mm/rev /.1 /rev (fine feeding) Carbide tipped measuring face. Non-rotating spindle Graduations:.1mm,.5mm,.1mm,.5" or.2",.5" Spindle pitch:.5mm or.25mm Spindle face: Flat with carbide tip (more than HRA9) or spherical, lapped surface Scale surface: Hard-chrome plating Fixture thickness for clamp nut: 9.5mm (11.5mm*) *11-52, Range Order No. - 1mm mm mm mm mm mm mm 11-52* * Narrow range (within 1 rev.):.2mm Graduation Accuracy* Stem dia. Stem Spindle face.1mm ±3 / ±1.5µm 12mm w/clamp nut Flat (carbide tip).1mm ±3 / ±1.5µm 12mm w/clamp nut Flat (carbide tip).1mm ±3 / ±1.5µm 12mm w/clamp nut Flat (carbide tip).1mm ±3 / ±1.5µm 12mm w/clamp nut Flat (carbide tip).1mm ±3 / ±1.5µm 12mm w/clamp nut Spherical (SR8).1mm ±3 / ±1.5µm 12mm w/clamp nut Spherical (SR8).5mm.1mm ±3 / ±1.5µm 9.5mm w/clamp nut Spherical (SR3) Range Order No. Graduation Accuracy* Stem dia. Stem Spindle face -.2" " ±.15" / ±.6".5" w/clamp nut Flat (carbide tip) -.2" " ±.15" / ±.6".5" w/clamp nut Flat (carbide tip) -.2" " ±.15" / ±.6".5" w/clamp nut Flat (carbide tip) -.2" " ±.15" / ±.6".5" w/clamp nut Flat (carbide tip) -.5" " ±.2" / ±.6".5" w/clamp nut Spherical (SR8) -.5" " ±.2" / ±.6".5" w/clamp nut Spherical (SR8) -.5" 11-54*.2".1" ±.15" / ±.6".375" w/clamp nut Spherical (SR3) * Narrow range (within 1 rev.):.6" DIMENSIONS AND MASS ø8 ø () () ø ø ø8 ø () ().6 ø21.6 ø21 M12x (35.2) (95) / / g M12x (36.2) (72.5) / / g SR3 ø () ø () Fine-feed thimble Coarse-feed thimble ø5 ø21 ø13 M9.5x.5 15 (17) (8.5) / g ( ): when retracting the spindle until its stroke end. B-69

70 Micrometer Heads SERIES 152 for XY-Stage , , , Non-rotating device is attached to the spindle tip. Floating thimble allows easy zero setting at any spindle position. Bidirectional graduation for easy reading in both directions , Adjustable spindle can be moved with the thimble held at any position, allowing easy zero-setting. Range Order No. - 25mm mm mm * - 25mm * *.1mm reading is obtained with vernier Accuracy Stem dia. Stem Spindle face Remarks ±2µm 18mm Plain Flat (hardened) with for X-axis, Bidirectional grad. ±2µm 18mm Plain non-rotating device for Y-axis, Bidirectional grad. ±2µm 18mm Plain Spherical with carbide for X-axis, with vernier ±2µm 18mm Plain tip (SR1) for Y-axis, with vernier Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 1" ±.1".79" Plain Flat (hardened) with for X-axis, Bidirectional grad. - 1" ±.1".79" Plain non-rotating device for Y-axis, Bidirectional grad Graduations:.5mm,.1mm* *vernier reading Spindle pitch: 1mm Spindle face: Flat (hardened) or spherical with carbide tip (more than HRA9), lapped surface Scale surface: White anodized aluminum DIMENSIONS AND MASS ø49 ø11 ø ø (27.7) (91) / g ø SR (3.7) A 14 ø51 ø (19.2) g ( ): when retracting the spindle until its stroke end. B-7

71 Micrometer Heads SERIES 197 Non-Rotating Spindle and Large Thimble Graduations:.5mm or.2" Spindle pitch: 1mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: White anodized aluminum Large thimble micrometer head with non-rotating spindle. Floating thimble allows easy zero setting at any spindle position. Bidirectional graduation for easy reading in both directions. Dual-spindle mechanism for quick feeding of 1mm/rev. Carbide tipped measuring face. Range Order No. - 5mm DIMENSION AND MASS Accuracy Stem dia. Stem Spindle face Remarks ±5µm 18mm Plain Flat (carbide tip) Bidirectional graduation Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 2" ±.2".79" Plain Flat (carbide tip) Bidirectional graduation ø ø (29) 64 (89) / g ( ): when retracting the spindle until its stroke end Graduations:.5mm or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: White anodized aluminum Micrometer Heads SERIES 153 Fine Graduation and High Accuracy Fine graduation and high resolution model. Large thimble micrometer head with non-rotating spindle. Bidirectional graduation for easy reading in both directions. Carbide tipped measuring face. Range Order No. - 25mm *Wide range / narrow range Accuracy * Stem dia. Stem Spindle face Remarks ±1 / ±.5µm 18mm Plain Flat (carbide tip) Bidirectional graduation Range Order No. Accuracy * Stem dia. Stem Spindle face Remarks - 1" ±.4" / ±.2".79" Plain Flat (carbide tip) Bidirectional graduation *Wide range / narrow range DIMENSIONS AND MASS A ø8 -.2 ø38.1 ø M4X.7 PCD28 View from A (35.4) (1) / g ( ): when retracting the spindle until its stroke end. B-71

72 Digital Micrometer Heads SERIES 164 High Resolution and High Accuracy Connecting with an external display unit, the Electronic Micrometer Head provides the most efficient means of obtaining precision measurement on XY-stages and similar applications. External display units (KA Counter) are optional. Stem diameter: 18mm Resolution:.1mm When using the external KA counter (must purchase adapter: 9AAA27) A Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 25mm ±.1mm / ±.5mm* 38mm Plain Flat (carbide tip) High accuracy model *Wide range / narrow range DIMENSIONS AND MASS 3 6 (35) 85 (11) ø38 (1) ø88 ø ( ): when retracting the spindle until its stroke end. : KA counter DIMENSIONS Order No A Resolution.1mm,.5mm,.1,.5 (selectable) Mass 1.1kg 9AAA27: Adapter (must purchase) Mounting stud x2 (M5) B-72

73 Micrometer Heads SERIES 25 with Digit Counter Digit counter for easy reading of spindle movement. Carbide tipped measuring face. Ratchet Stop for constant force. Range Order No. - 25mm Accuracy Stem dia. Stem Spindle face Remarks ±2µm 1mm Plain Flat (carbide tip) Range Order No. Accuracy Stem dia. Stem Spindle face Remarks - 1" ±.1".375" Plain Flat (carbide tip) w / vernier (.1") DIMENSIONS AND MASS Graduations:.1mm or.1" Spindle pitch:.5mm Spindle face: Flat with carbide tip (more than HRA9), lapped surface Scale surface: Hard-chrome plating 42 ø (17) (118.8) / Mass: 165g ( ): when retracting the spindle with adjustable handle Micro Jack SERIES 7 Used for accurate leveling of machines, surface plates, and other precision instruments. Easy adjustment under heavy load. 785 Graduations:.1mm Range Order No. Graduation Max. Load Remarks 6-75mm 785.1mm 4kg adjustable handle DIMENSIONS AND MASS SR1 9 (85) 15 ø ø4 ø Mass: 4g ( ): when retracting the spindle with adjustable handle B-73

74 Precision Lead Screw Mitutoyo manufactures simple and less expensive precision lead screws for precise positioning mechanisms and fine feed mechanisms, in addition to the conventional micrometer heads. Mitutoyo also manufactures screws with special specifications, such as.25 mm pitch, as well as those with the standard.5 mm feed pitch and with dimensions and forms that meet customer's requirements. Durability: 1, cycles are guaranteed (use condition: 4 kg load; 2 kg for AS-6.5 and BS-6.5) Main applications Precision feed stages Fine adjustment of optical elements (mirrors, prisms) Fiber optic centering devices Various assembly and adjustment jigs 4AZA164 4AZA162 4AZA16 Micrometer Head Precision lead screw Pinion Drive motor Order No. Model Stroke (mm) Feed pitch (mm) Feed accuracy (µm) Stem diameter (mm) Tip diameter (mm) Tail diameter (mm) Screw nominal diameter Sleeve diameter (mm) Measuring face 4AZA16 AS-6.5 1g 6.5 ±5 ø6 ø3.5 ø3 M4.5 x.5 ø7 4AZA161 BS g Hardened 4AZA162 AS-13 27g 13.5 ø9.5 ø5 ø5 ø1.5 4AZA163 BS g ±2 M7.35 x.5 4AZA164 AS-25 61g 25 ø1 ø6 ø12 Carbide 4AZA165 BS g Mass Others Example Application AS type: Flat spindle tip without nut BS type: Spherical spindle tip with nut DIMENSIONS Type A: Straight type Spindle (material: SKS hardening steel) Diameter of top tip L3 L1 Stem diameter L Sleeve (material: free-cutting steel, black oxide finish) Nominal diameter of screw L2 L4 Diameter of bottom tip External diameter of sleeve Type B: Stem with nut Clamp-down nut Spindle (material: SKS hardening steel) Diameter of top tip L3 L5 L1 Stem diameter L Sleeve (material: free-cutting steel, black oxide finish) Nominal diameter of screw L2 L4 Diameter of bottom tip External diameter of sleeve Order No. L L1 L2 L3 L4 L5 4AZA AZA AZA AZA AZA AZA B-74

75 B D J M K K B I 2-L A C D A C F H E G I F G H 2-J E D I J Fixtures for Micrometer Heads Workstage Fixture Micrometer head The act of fabricating brackets to mount micrometer heads for each particular application can be laborious and costly. Mitutoyo offers various types of fixtures for micrometer heads to meet a wide range of applications. These fixtures are made of nickel-plated cast iron. There are two types of fixtures for micrometer heads with or without clamping nut on the stem. DIMENSIONS: Fixtures for plain stem type micrometer heads Note: Supplied with a socket head screw (M3x.5x12mm) for the fixtures to be used with a micrometer head without clamp nut (plain stem type micrometer head). Order No A ø9.5 ø9.5 ø1 B C D E F G H I J K L ø3.4 ø4.5 ø4.5 M M3x.5 M3x.5 M3x.5 Order No A ø9.5 ø9.5 ø1 B C D E F G H I J ø3.4 ø4.5 ø4.5 K M3x.5 M3x.5 M3x.5 B E G M C 2-L A B K A D H F J C 2-I F H E G Order No A ø9.5 ø9.5 ø1 B C D E F G H I ø3.4 ø4.5 ø4.5 J M3x.5 M3x.5 M3x.5 Order No A ø9.5 ø9.5 ø1 B C D E F G H I J K L ø3.4 ø4.5 ø4.5 M M3x.5 M3x.5 M3x.5 B-75

76 B D J B 2-K A F A F C D H G C E I G H 2-I E C D I J Fixtures for Micrometer Heads DIMENSIONS: Fixtures for micrometer heads with clamp nut Order No A ø9.5 ø9.5 ø1 B C D E F G H I J K ø3.4 ø4.5 ø4.5 Order No A ø9.5 ø9.5 ø1 B C D E F G H I ø3.4 ø4.5 ø4.5 B C E 2-K A B A F D 2-G H G F E L Order No A ø9.5 ø9.5 ø1 B C D E F G ø3.4 ø4.5 ø4.5 Order No A ø9.5 ø9.5 ø1 B C ø15 ø15 ø15 D E F G H I J K ø3.4 ø4.5 ø4.5 L B-76