deview electronics VDP20 Series Vandal Dome

Size: px

Start display at page:

Download "deview electronics VDP20 Series Vandal Dome"

Erin Justina Fisher
5 years ago
Views:

2 VDP20 Series Vandal Dome

3 Model: VDP20W Vandal Resistant Dome Features Tough Impact Vandal Resistant Polycarbonate Construction Indoor/Outdoor Use Surface or Recessed Mount

4 Model: VDP20W Vandal Resistant Dome Features IP66 Rated 12VDC or 24VAC Operation for camera modules Service and Programming Jack

5 Model: VDP20W Vandal Resistant Dome Features Captive Lid Screws Threaded Conduit plugs Snap on liner

6 Features Compatible with all GC series camera/lens modules. Multiple camera modules available Day/Night True Day/Night Wide Dynamic Range All feature 180 Tilt, 360 pan

7 VDP Series Vandal Dome Features Captive screws on lid No loose screws to drop

8 VDP Series Vandal Dome Features Notches in base and lid so unit will assemble easier Lowers Installation time

9 VDP Series Vandal Dome Features Surface or recessed mount in one unit Carry less inventory

10 VDP Series Vandal Dome Features Fold out wings for installations in drop ceilings or sheetrock Lowers Installation time

11 VDP Series Vandal Dome Features Multiple mounting options Surface Ring Lowers inventory cost

12 VDP Series Vandal Dome Features Mounting holes allows for prethreading of mounting screws Lowers Installation time

13 VDP Series Vandal Dome Features ½ threaded conduit opening on side ¾ threaded conduit opening on bottom Better fit for conduit fittings Lowers Installation time

14 VDP Series Vandal Dome Features Supplied with rubber cable entry sealing plugs Helps keep debris and bugs out the dome Lowers service calls needed for general cleaning

15 VDP Series Vandal Dome Features Service Jack and programming jack Used for local setup Lowers Installation time

16 VDP Series Vandal Dome Features Service Jack and programming jack Used for local setup WDR programmer Must install white lead wires with red strip from camera to middle connector on service jack to make the jack active.

17 VDP Series Vandal Dome Features Accessory package shipped with dome

18 VDP Series Vandal Dome Compatible with all GC Camera Modules Total Axis Gimble 3 Axis Gimble design 90 Straight down 90 Tilt 360 Rotation

19 GC Camera Modules Models GCDNH25V6 High Resolution 540 Color 570 Black/White Day/Night mode 2.5-6mm Vari focal Auto Iris Lens F1.3 12VDC/24VAC

20 GC Camera Modules Models GCDNH38V95 High Resolution 540 Color 570 Black/White Day/Night mode mm Vari focal Auto Iris Lens F1.2 12VDC/24VAC

21 GC Camera Modules Models GCDNH9V22 High Resolution 540TVL Color 570TVL Black/White Day/Night mode 9-22mm Vari focal Auto Iris Lens F1.8 12VDC/24VAC

22 GC Camera Modules Models GCDNH38V95WD Wide Dynamic High Resolution 504+TVL Day/Night mode mm Vari focal Auto Iris Lens F1.2 12VDC/24VAC

23 GC Camera Modules Models GCDNH9V22WD Wide Dynamic High Resolution 504+TVL Day/Night mode 9-22mm Vari focal Auto Iris Lens F1.8 12VDC/24VAC

24 GC Camera Modules Models GCTDNH29V10 High Resolution 540TVL Color 570TVL Black/White True Day/Night mode mm Vari focal Auto Iris Lens F1.2 12VDC/24VAC

25 GC Camera Modules Models GCTDNH29V10WD Wide Dynamic High Resolution 504+TVL Color 570TVL Black/White True Day/Night mode mm Vari focal Auto Iris Lens F1.2 12VDC/24VAC

26 VDP Series Vandal Dome Features GC Camera Modules Simple installation Secure with three screws

27 VDP Series Vandal Dome Features Snap on camera liner Lowers Installation time

Day/Night Vandal Camera Adjustments (GCDNHxxx) Focus & field of view adjustment Turn the levers on the side of the varifocal camera to adjust the focus

28 Day/Night Vandal Camera Adjustments (GCDNHxxx) Focus & field of view adjustment Turn the levers on the side of the varifocal camera to adjust the focus and field of view settings. TIP: If necessary, perform the final focus through the dome cover, holding it to the lens reversed to confirm the final results.

29 True Day/Night Vandal Camera Adjustments (GCTNHxxx) Focus & field of view adjustment Turn the levers on the side of the varifocal camera to adjust the focus and field of view settings. TIP: If necessary, perform the final focus through the dome cover, holding it to the lens reversed to confirm the final results.

30 Day/Night Vandal Camera Adjustments (GCDNHxxx) DIP switch settings SDN mode When this switch is set to "ON" the camera will produce color images under normal lighting conditions. In reduced lighting the camera will switch to monochrome mode. Auto White Balance AWB: The camera operates in the normal Auto White Balance range 2700K~11000K. AWB EX: The camera operates in the extended Auto White Balance range 2000K~18000K. SYNC In LL mode the V-Phase may be adjusted to compensate for connected supply phase differences. Only applicable for 24VAC supply - otherwise the camera operates with INT(internal) sync. Flickerless mode When this switch is set to ON, the camera reduces flicker in the image under fluorescent lighting. Back Light Compensation When this switch is ON, this option improves the camera s response to strong, unwanted lighting effects behind the required subject. AGC mode Setting to TURBO will automatically increase the sensitivity in low light. Selecting NORMAL will remove noise from the image, but it will also limit the camera s sensitivity. Vertical phase adjustment Use this adjustment when using an AC supply to align the camera phase with that of the supply. Sync must be switched to "LL". DC-IRIS adjustment This is factory set and should not normally require adjustment except to compensate for excessive image blooming.

31 True Day/Night Vandal Camera Adjustments (GCTNHxxx) DIP switch settings TDN mode When this switch is set to "ON" the camera will produce color images under normal lighting conditions. In reduced lighting the camera will switch to monochrome mode. Auto White Balance AWB: The camera operates in the normal Auto White Balance range 2700K~11000K. AWB EX: The camera operates in the extended Auto White Balance range 2000K~18000K. SYNC In LL mode the V-Phase may be adjusted to compensate for connected supply phase differences. Only applicable for 24VAC supply - otherwise the camera operates with INT(internal) sync. Flickerless mode When this switch is set to ON, the camera reduces flicker in the image under fluorescent lighting. Back Light Compensation When this switch is ON, this option improves the camera s response to strong, unwanted lighting effects behind the required subject. AGC mode Setting to TURBO will automatically increase the sensitivity in low light. Selecting NORMAL will remove noise from the image, but it will also limit the camera s sensitivity. SHARP When this switch is set to "ON" the camera enhances the sharpness of the image. Day & Night (D&N) The D&N mode can be activated only when TDN is set to ON. When set HI, the camera will switch to Night (Monochrome) mode at a lower light level. Vertical phase adjustment Use this adjustment when using an AC supply to align the camera phase with that of the supply. Sync must be switched to "LL". DC-IRIS adjustment This is factory set and should not normally require adjustment except to compensate for excessive image blooming.

WDR Vandal Camera Programming Camera Adjustments and Programming With the exception of the focus and field of view adjustments (made using levers A and B) all settings for the WDR series camera are

32 WDR Vandal Camera Programming Camera Adjustments and Programming With the exception of the focus and field of view adjustments (made using levers A and B) all settings for the WDR series camera are made using its on screen menu display. A working video monitor and a separate plug-in control board (C) are required to view and select options. 1. Within the dome enclosure, attach the Control Board connector to the socket (D) at the top of the service jack interface board. Ensure that the OSD lead (F) is connected between the middle socket of the smaller circuit board and the camera. 2. With power applied to the camera and a video monitor connected, press and hold the ENTER key for three seconds to access the top level menu. A map of the menu options are shown below. 3. To navigate through the menus, use the arrow keys on the control board and use the ENTER key the SAVE SETTINGS option in the SAVE/RESTORE menu. Otherwise any changes made will be lost when the camera is next reset or has its power cycled. See instruction manual to view programming menu tree

33 VDP Series Vandal Dome Features Optional Accessories SVC-CABLE Service Jack Cable Used for Local Set up

34 VDP Series Vandal Dome Features Optional Accessories Electrical box adaptor plate VP-4S

35 VDP Series Vandal Dome Features Optional Accessories Pendant Cap VP-PC Connect directly to a ¾ threaded conduit/pipe Can be used with a ceiling flange or wall mount

36 VDP Series Vandal Dome Features Optional Accessories Wall Mount BKPCWM Used in conjunction with the pendant cap VP-PC

37 VDP Series Vandal Dome Features Optional Accessories Corner Mount VP-CM

38 For complete product details please visit or For additional information call our office at

deview electronics MD4 Series Indoor Mini Domes

deview electronics MD4 Series Indoor Mini Domes MD4 Series Indoor Mini Domes 4 Indoor Mini Dome Six version available MD4DN22H25V6 MD4DN22H39 MD4DN22H39T MD4DN22H39WD MD4DN22H9V22 MD4DN22H9V22WD Model: MD4DN22H25V6 4 Indoor Mini Dome Features High Resolution