X-Beam Waterproof Action Camera Light USER GUIDE

Transcription

1 X-Beam Waterproof Action Camera Light USER GUIDE

2

3

4 EN Join the social movement and follow us on #ChallengeYourself Share your footage with us on our social media Need help? To view the entire Kaiser Baas product range and accessories visit: 4

5 EN Languages English 1-18 Français Espaná

6 EN Table of Contents Languages 3 Safety Precautions 5 What s in the Box 6 Product Diagram 7 Setup Your X-BEAM 8 Battery Operation 8 Recharging the Battery: 9 Operating Guide 10 Modes of Use 11 To cycle between the different modes: 11 LED Indicators 12 Attaching Your X-BEAM 13 Waterproof Seal Care 14 Specifications 15 Contact Us 16 6

7 Safety Precautions EN Before operating the X-Beam Action Camera Light, please ensure you have read and understood the safety precautions. The X-Beam Action Camera Light is a high powered LED light that will get hot after extended periods of use. Exercise caution when operating the X-Beam Action Camera Light to avoid injury. WARNING: DO NOT stare directly into the light source. DO NOT use optical instruments to look into the light source. DO NOT point the X-Beam Action Camera Light into people s eyes. DO NOT expose the X-Beam Action Camera Light to fire or extreme heat. DO NOT attempt to modify or disassemble the product. This will void your warranty. DO NOT use the X-Beam Action Camera Light if the housing has been cracked or damaged. 7

8 EN What s in the Box Please ensure the product package has the following contents: A X-Beam Action Camera Light B Rechargeable 2200mAh Battery C Dual Mount D Screw Bolt E Short Screw F USB Cable G Quick Release Mount H Replacement Rubber Seal A B C D E F G H 8

9 Product Diagram A ON/OFF/MODE Button EN B LED MODE Indicator A B Front Back 9

10 EN Setup Your X-BEAM Ensure that your X-Beam Action Camera Light is fully charged before use. Battery Operation Removing the battery: 1. Lift the clip on the top of the X-Beam Action Camera Light to reveal the battery housing. (fig.01) 2. Slide the battery out of the housing. (fig.02) Fig.01 Fig.02 10

11 Model: BP-01 Great Power IEC: 1ICP7/26/41-4 Rechargeable Li-ion battery 3.7VDC 2200mAh 8.14Wh LI-ION Input: 5VDC 2.1A CHARGE IN PROGRESS CHARGE COMPLETE CAUTION:DO NOT SHORT CIRCUIT, DISASSEMBLE OR EXPOSE THE BATTERY TO FIRE OR WATER. RISK OF FIRE AND BURNS. DO NOT OPEN, CRUSH, HEAT ABOVE 60 C OR INCINERATE. FOLLOW MANUFACTURER S INSTRUCTIONS. Manufacturer: GREAT POWER BATTERY(ZHUHAI)CO.,LTD. DATE: Recharging the Battery: 1. To charge your X-Beam Action Camera Light, connect the provided Micro USB cable. 2. Connect the USB cable to an electronic device with a USB port. 3. A full charge cycle will take approx. 3 hours by 1A/2.1A charger. 4. A red light indicates the battery is charging. 5. A green light indicates the battery is fully charged. EN LED INDICATOR: Charging Charged Note: If using a wall charger, ensure that it is a certified product for your region. AC Input: VAC 50/60Hz. DC Output: 5VDC 1A/2.1A. Only use a USB charger with suitable approval and certification. Do not charge in conditions outside of the 10 C-45 C range. 11

12 EN Operating Guide Insert the battery into the light, close the housing and snap the clip closed. Refer to Fig. 01 and Fig. 02 Fig.01 Fig.02 The On/Off switch is located on the top of the X-Beam Action Camera Light and is used to power on the device and to change the light modes. Press and hold the power button for 2 seconds to turn the X-Beam on. Hold the power button for 6 seconds to turn the X- Beam off. 12

13 Modes of Use EN There are 3 modes of operation for the X-Beam Action Camera Light. Each mode has a High and Low light setting. They cycle through in the following order: Wide Angle High, Wide Angle Low, Ambient High, Ambient low, Target High, Target Low, Off. To cycle between the different modes: Whilst the light is on click the power button. Continue to click the button to cycle through. The light will turn off after a cycle. LIGHTING MODE SPECIFICATIONS MODES WIDE AMBIENT TARGET LUMENS 1000/ / /150 BATTERY 0.5/1 hr 0.75/1.5 hr 1.5/3.5 hr CREE LEDS 6 LED 4 LED 2 LED 13

14 EN LED Indicators Low Voltage Indicator- The red battery icon will switch on when the battery voltage reaches approximately 3.35V 2. Target Mode 3. Ambient Mode 4. Wide Mode 5. Overheat Indicator This icon will switch on when the temperature of the light reaches approximately 55 C. Please switch off the light and let it cool when this light is on. 14

15 Attaching Your X-BEAM EN Attach the X-Beam Action Camera Light to your Action Camera by using the dual mount included. You can alternatively attach the X-Beam using any GoPro Mount for a wide range of situations. It pairs perfectly with a bike mount or float grip. 15

16 EN Waterproof Seal Care To maintain your X-Beam Action Camera Light, it is recommended that you clean the light and waterproof seal after every use. The waterproof seal, located on the door, can be cleaned by gently wiping away any dirt, dust or debris with a clean, dry and soft cloth. Ensure the seal is clean to maintain the seal integrity. If the seal becomes damaged or lost, please replace with the included replacement part. Always check the seal for any dirt, dust or debris prior to use. After use in salt water, rinse the X-Beam Action Camera Light in fresh water to prevent corrosion. 16

17 Specifications Number of LED s 6 Type of LED s XT-E CREE Color Temperature 5000K Light Modes 3 Mode Wide Ambient Target Lumens 1000/ / /150 Battery 0.5/1 hr 0.75/1.5 hr 1.5/3.5 hr LED Angle Battery 3.7VDC 2200mAh 8.14Wh Li-Ion Charge Time 3 Hours with 5V 2.1A USB Adaptor Waterproof 40m IP68 Dimensions 70x77x42 mm Weight 215g EN 17

18 EN Contact Us Need further assistance? Please visit: Or For the full Kaiser Baas accesories range visit 18

19