AQ_G24 GSM Terminal Card Motorola Cellular GSM Engine

Transcription

1 AQ_G24 GSM Terminal Card Motorola Cellular GSM Engine Version: AQ_G24 Terminal Card_HD_V JUL

2 Hardware Interface Description 1. Hardware Features of the AQ_G24 Terminal Card Feature Implementation Incorporates G24 module Frequency bands Power supply Operating temperature Physical RoHS, WEEE Connectors on board SIM on Board The Motorola G24 module handles all GSM processing for, signal and data within the AQ_G24 Terminal Card. Quad band: GSM 850/900/1800/1900MHz Single supply voltage 5V to 16V Or via USB from PC ( Option: need to add resistor ) -20 C to +70 C ambient temperature Dimensions: 50mm x 40m x 10 mm Weight: 50g All hardware components are fully compliant with the EU RoHS and WEEE Directives UART 1 RS232 level UART 2 TTL level + 2 input GPIO USB type mini B SIM with switch detection - 2 -

3 2. Interface Description 2.1 Overview AQ_G24 Terminal provides the following connectors for power supply, Interface and antennas: 1. MMCX connector (female) for GSM antenna 2. 8 pole 2mm connector for power supply, UART_1 RS232, On/Off, IGN 3. SIM card holder 4. 6 pole 2mm connector for output power supply 3.3V, UART_2 TTL 5. Led GSM 6. USB type mini B connector Figure 1: AQ_G24 Terminal Card Top view 1 Figure 2: AQ_G24 Terminal Card Bottom view

4 2.2 Block Diagram Figure 3 shows a block diagram of a sample configuration that incorporates a AQ_G24 Terminal Card and typical accessories. Antenna GSM MMCX Modem On/Off LED G24 Motorola UART 1 Tx Rx CTS RTS SIM Level Shifter RS232 8 pin 2mm J3 UART 1 RS232 Tx Rx CTS RTS Power GND LDO Power Supply 5-16V GND Enable On/Off On/Off 6 pin 2mm J5 UART 2 Tx Rx UART 2 TTL UART 2 TTL Tx UART 2 Rx UART 2 GPIO2 GPIO2 GPIO3 GPIO3 LDO 3.0V Power 3.0v GND 5 pin J6 USB USB mini B Figure 3: Block diagram - 4 -

5 2.3 Connector J3 input Power Supply and RS232 The power supply of the AQ_24G Terminal Card has to be a single voltage source of POWER 5V-16V capable of providing a peak during an active transmission. The AQ_24G Terminal Card is protected from reversal supply voltage. The power supply has to be compliant with the EN60950 guidelines. RS232 serial interface of the AQ_G24 Terminal provide 4pin connection TX, RX, RTS, CTS Pin Signal name Use 1 POWER Input Power supply range 5-16V 2 TX_UART1 RS232 TX 3 RX_UART1 RS232 RX 4 RTS_UART1 RS232 RX 5 CTS_UART1 RS232 RX 6 Ground Ground 7 Enable / 3.0V Enable- turn ON or OFF the card, option resistor replacement 3.0v 8 ONOFF/ IGNITION ON or OFF modem, option resistor replacement input modem IGNITION Table 1: Pin assignment of the plug for power supply and relay 8 J3 1 Figure 4: 8-pole plug for power supply and RS232 output

6 2.3.1 Supply voltage requirements The DC power supply must be connected to the POWER input: Input voltage range 5-16V DC Nominal Voltage 12V DC Power Supply current rating: min. Power Supply ripple: max. 120mV Input current in idle mode: 12V Input average current in communication mode: 12V 2.4 RS-232 Interface The serial interface of the AQ_G24 Terminal is intended for the communication between the GSM module and the host application. This RS-232 interface is a data and control interface for transmitting data, AT commands and providing multiplexed channels. EMC immunity complies with the vehicular environment requirements according to EN The user interface of the AQ_G24 Terminal is accessible from a Data Terminal Equipment DTE connected to the RS232 interface and it is managed by AT commands according to the GSM and specification and the supported commands are listed in the AT Commands Reference Guide. Pin no. Signal name I/O Function of application 1 2 RXD O Receive Data 3 TXD I Transmit Data 4 5 GND - Ground 6 7 RTS I Request To Send 8 CTS O Clear To Send 9 Figure 5: Pin assignment RS-232 (D-Sub 9-pole female) Table 2: D-Sub 9-pole female RS232 Connector type on the terminal is: RS-232 through D9-pin female Baud rate from 300 to bit/s Short circuit (to Ground) protection on all outputs. Input voltage range: -12V to +12V - 6 -

7 2.5 Connector J5 GPIO Interface and UART 2 The internal power supply of 3v 200ma of the AQ_24G Terminal Card can supply power to external unit such as GPS modem. UART_2 serial interface of the AQ_G24 Terminal provide 2pin connection TX, RX GPIO interface provides via 2 pins, GPIO_ 2 and GPIO_3. Pin Signal name Use 1 POWER Output Power supply 3.0v 2 TX_UART2 UART_2 TX 3 RX_UART1 UART_2 RX 4 GPIO_2 GPIO_2 5 GPIO_3 GPIO_3 6 Ground Ground J5 1 6 Figure 6: 6-pole plug for GPIO and UART_2 2.6 Connector J6 USB The USB interface of the AQ_G24 Terminal is intended for the communication between the GSM module and the PC host. The USB interface can provides the power to operate the GSM terminal need to add resistor on board. Connector USB mini B type

8 2.9 Status LED Red LED displays the G24 Modem status. Red LED status permanently on permanently off Device Status Modem ON Modem OFF Table 3: RED LED Status 4. Mechanical Characteristics Weight 50g Dimensions (max) L x W x H 50m x 40 x 10mm Temperature range -20 C to +70 C ambient temperature Mechanical vibrations Amplitude 7.5mm at 5-200Hz sinus Air humidity 5% - 85% Table 5: Mechanical characteristic AQ_G24 Terminal Hardware Interface Description - 8 -

9 5.2 Power Supply This chapter provides specifications for the power supply which serves the Terminal. The power supply we recommended is 12V 1.2A part number EZ12V1.2A. The type of the receptacle assembled on the AQ_G24 Terminal is 6 pin Micro Mate-N-LOK 2mm from MOLEX. Mating headers can be chosen from the MOLEX Micro Mate-N-LOK Series. For latest product information GSM antenna This chapter provides specifications for the GSM antennas which serves the Terminal. We recommended 1 types of GSM antenna with MMCX connector: 900/1800/1900Mhz 1dBm 5 cm for internal assembly part number EZantenna1db3M int. 6. SAFETY RECOMMANDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. Where there is risk of explosion such as gasoline stations, oil refineries, etc It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information s are available on the European Community website: The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: AQ_G24 Terminal Hardware Interface Description - 9 -