DEFENSE INFORMATION SYSTEMS AGENCY P. O. BOX 549 FORT MEADE, MARYLAND

Transcription

1 DEFENSE INFORMATION SYSTEMS AGENCY P. O. BOX 549 FORT MEADE, MARYLAND IN REPLY REFER TO: Joint Interoperability Test Command (JTE) MEMORANDUM FOR DISTRIBUTION SUBJECT: Extension of the Joint Interoperability Certification of the Cisco Unified Capabilities Collaboration Product (UCCP) 8 References: (a) Department of Defense Instruction , "DoD Unified Capabilities (UC)," 9 December 2010 (b) DoD CIO, Memorandum, "Interim Guidance for Interoperability of Information Technology (IT) and National Security Systems (NSS)," 27 March 2012 (c) through (h), see Enclosure 1. Certification Authority. Reference (a) establishes the Joint Interoperability Test Command (JITC) as the Joint Interoperability Certification Authority for UC products, Reference (b). 2. Conditions of Certification. The Cisco Product 8, hereinafter referred to as the System Under Test (SUT), meets the critical requirements of the Unified Capabilities Requirements (UCR), Reference (c), and is certified for joint use as a Product with the conditions described in Table 1. This certification expires upon changes that affect interoperability, but no later than the expiration date of the UC Approved Products List (APL) memorandum. This extension is for Desktop Review (DTR) 1, which was requested to upgrade the UCCP Cisco Unified Communication Manager (CUCM) and Cisco Unified Presence Server (CUPS) from Release 8.6(1) ( ) to SU3, the Jabber was upgraded from Release to 11.0, the 29xx and 39xx series Media Gateways (MGs) were upgraded from Release Internetwork Operating System (IOS) M2 to 15.6(2) T, and the 29xx and 39xx series Session Border Controllers (SBCs) were upgraded from Release IOS M2 to IOS 15.5(3)M3. See Paragraph 4 for the test details. Table 1. Conditions Condition Operational Impact Remarks UCR Waiver None See note 1. None. The SUT does not support chat room capabilities. Conditions of Fielding Open Test Discrepancies Minor CLOSED See note 2.

2 Table 1. Conditions (continued) 1. The SUT received a waiver from DoD CIO for IPv6 with release Cisco Unified Communication Manager (CUCM) and Cisco Unified Presence Server (CUPS) Release 8.6(1) ( ), and Jabber Release This DTR1 updates the CUCM and CUPS to Release SU3, and Cisco Jabber for Windows to Release 11.0, which were included in the Cisco ESC15 IO certification letter under TN and determined by JITC to be fully IPv6 compliant. Therefore based on JITC analysis the DoD CIO IPv6 is no longer relevant to the SUT. 2. The vendor updated the SUT under DTR1, which includes the following updates that fix this discrepancy: CUCM and CUPS updated to Release SU3, Cisco Jabber for Windows to Release DISA Defense Information Systems Agency DTR Desk Top Review ESC Enterprise Session Controller IPv6 Internet Protocol version 6 JITC Joint Interoperability Test Command OSD Office of the Secretary of Defense POA&M Plan of Action and Milestones UCR Unified Capabilities Requirements 3. Interoperability Status. Table 2 provides the SUT interface interoperability status and Table 3 provides the Capability Requirements (CR) and Functional Requirements (FR) status. Table 4 provides a UC APL product summary. Table 2. Interface Status Interface Threshold CR/FR Requirements Status Remarks (See note 1.) Network Management Interfaces IEEE 802.3i (10BaseT UTP) (C) (See note 2.) 1 Met IEEE 802.3u (100BaseT UTP) (C) (See note 2.) 1 Met IEEE 802.3ab (1000BaseX) (C) (See note 2.) 1 Met UC Network Interfaces IEEE 802.3i (10BaseT UTP) (C) (See note 2.) 1, 2, 3 Partially Met See note 3. IEEE 802.3u (100BaseT UTP) (C) (See note 2.) 1, 2, 3 Partially Met See note 3. IEEE 802.3ab (1000BaseX) (C) (See note 2.) 1, 2, 3 Partially Met See note 3. DISN Legacy Interfaces ISDN T1 PRI NI-2 (C) 1 and 2 Met E1 PRI ITU-T Q.931 (C) 1 and 2 Met 2-wire analog (C) 1 and 2 Not Tested The SUT does not support this conditional interface Client Interfaces IEEE 802.3i (10BaseT UTP) (C) (See note 2.) 1, 2, 3 Met See note 3. IEEE 802.3u (100BaseT UTP) (C) (See note 2.) 1, 2, 3 Met See note The SUT high-level CR and FR ID numbers depicted in the Threshold CRs/FRs column can be cross-referenced in Table 3. These highlevel CR/FR requirements refer to a detailed list of requirements provided in Reference (c), Enclosure The SUT must provide a minimum of one of the listed interfaces. 3. The SUT received a waiver from DoD CIO for IPv6 with release Cisco Unified Communication Manager (CUCM) and Cisco Unified Presence Server (CUPS) Release 8.6(1) ( ), and Jabber Release This DTR1 updates the CUCM and CUPS to Release SU3, and Cisco Jabber for Windows to Release 11.0, which were included in the Cisco ESC15 IO certification letter under TN and determined by JITC to be IPv6 compliant. Therefore, based on JITC analysis the DoD CIO IPv6 is no longer relevant to the SUT. 2

3 Table 2. Interface Status (continued) 802.3ab 1000BaseT Gbps Ethernet over twisted pair at 1 Gbps (125 Mbps) 802.3i 10BaseT Mbps over twisted pair 802.3u Standard for 100 Mbps Ethernet 10BaseT 10 Mbps (Baseband Operation, Twisted Pair) Ethernet 100BaseT 100 Mbps (Baseband Operation, Twisted Pair) Ethernet 1000BaseX 1000 Mbps Ethernet over fiber C Conditional CR Capability Requirement DISN Defense Information Systems Network E1 European Basic Multiplex Rate (2.048 Mbps) FR Functional Requirement Gbps Gigabits per second ID Identification IEEE Institute of Electrical and Electronics Engineers IPv6 Internet Protocol version 6 ISDN Integrated Services Digital Network ITU-T International Telecommunication Union - Telecommunication Standardization Sector Mbps Megabits per second NI-2 National ISDN Standard 2 OSD Office of the Secretary of Defense PRI Primary Rate Interface Q.931 Signaling Standard for ISDN T1 Digital Transmission Link Level 1 (1.544 Mbps) UC Unified Capabilities UTP Unshielded Twisted Pair Table 3. SUT Capability Requirements and Functional Requirements Status CR/FR UCR 2013 UCR Requirement (High-Level) (See note 1.) ID Reference Status 1 Voice and Video Collaboration Product Requirements (R) Met (See notes 2 and 3.) 2 Optional Voice and Video Collaboration Product Requirements (O) Met 3 IM/Chat/Presence Collaboration Product Requirements (R) Met (See note 4.) 1. The annotation of required refers to a high-level requirement category. The applicability of each sub-requirement is provided in Reference (c), Enclosure Security testing is accomplished by DISA-led Information Assurance test teams and the results published in a separate report, Reference (f). 3. The SUT received a waiver from DoD CIO for IPv6 with release Cisco Unified Communication Manager (CUCM) and Cisco Unified Presence Server (CUPS) Release 8.6(1) ( ), and Jabber Release This DTR1 updates the CUCM and CUPS to Release SU3, and Cisco Jabber for Windows to Release 11.0, which were included in the Cisco ESC15 IO certification letter under TN and determined by JITC to be IPv6 compliant. Therefore, based on JITC analysis the DoD CIO IPv6 is no longer relevant to the SUT. 4. The vendor updated the SUT under DTR1, which includes the following updates that fix this discrepancy: CUCM and CUPS updated to Release SU3, Cisco Jabber for Windows to Release CR Capability Requirement DISA Defense Information Systems Agency FR Functional Requirement ID Identification IM Instant Messaging IPv6 Internet Protocol version 6 O Optional OSD Office of the Secretary of Defense POA&M Plan of Action and Milestones R Required UCR Unified Capabilities Requirements 3

4 Product Name Software Release UC Product Type(s) Table 4. UC APL Product Summary Cisco Product Release SU3 Collaboration Product Product Identification Cisco Unified Capabilities Collaboration Product 8 supports collaboration between IP-based end users using Product Description VVoIP sessions, P, IM, and Multiuser Chat sessions. The solution also provides legacy TDM connectivity with T1 ISDN PRI and E1 ISDN PRI interfaces via the CP MG. Product Components (See note 1.) Component Name (See note 2.) Version Remarks Product Server (VVoIP) Product Server (VVoIP) Product Server (Presence/IM/Chat) Product Client Product SBC Product MG Cisco Unified Computing Systems with ESXi 5.1 UCS-B-200M2. A comprehensive list of supported hardware configurations can be found by selecting the "Cisco Unified Communications on the Cisco Unified Computing System" link at the following URL: MCS 7825 H3, MCS 7825 I3, MCS 7825 I4, MCS 7825 H4, MCS 7835 H2, MCS 7835 I2, MCS 7835 I3, MCS 7845 H2, MCS 7845 I2, MCS 7845 I3 UCS-B200-M1, UCS-B230-M2, UCS- B440-M2, UCS-B200-M3, UCS-C260- M2, UCS-C240-M3, UCS-C220-M3 Cisco Jabber for Windows Cisco 2911/2921/2951, 3925, 3925E, 3945, 3945E ISR Cisco 2911/2921/2951, 3925, 3925E, 3945, 3945E ISR CUCM SU3 CUCM SU3 CUPS SU3 Jabber 11.0 Windows 7 IOS 15.5(3)M3 IOS 15.6(2) T Unified Communications Manager solution consisting of multiple servers, voice gateways and IP phones. (See note 3.) IM/P Server to facilitate exchange of IM. (See note 4.) IM/P and VVoIP (See note 5.) Network border element that includes Session Border Control functions to enable end-to-end IP-based transport of voice, video and data between UC networks. (See note 6.) Voice gateway for TDM component connectivity; hosts DSN/PSTN trunk circuits. (See note 7.) 1. The detailed component and subcomponent list is provided in Reference (c), Enclosure Components bolded and underlined were tested by JITC. The other components in the family series were not tested but are also certified for joint use. JITC certifies those additional components because they utilize the same software and similar hardware and JITC analysis determined them to be functionally identical for interoperability certification purposes. 3. The SUT CUCM was upgraded from Release 8.6(1) ( ) to SU3 with DTR The SUT CUPS was upgraded from Release 8.6(5) ( ) to SU3 with DTR The SUT Cisco Jabber was upgraded from Release to 11.0 with DTR The SUT 29xx and 39xx series SBCs were upgraded from Release IOS M3 to IOS 15.5(3)M3 with DTR The SUT 29xx and 39xx series MGs were upgraded from Release IOS M2 to 15.6(2) T with DTR 1. APL Approved Products List CP Collaboration Product CUCM Cisco Unified Communications Manager CUPS Cisco Unified Presence Server DSN Defense Switched Network DTR Desktop Review E1 European Basic Multiplex Rate IM Instant Messaging IP Internet Protocol IOS Internetwork Operating System ISDN Integrated Services Digital Network ISR Integrated Services Router JITC Joint Interoperability Test Command MG Media Gateway P Presence PRI Primary Rate Interface PSTN Public Switched Telephone Network SBC Session Border Controllers SU System Update T1 Digital Transmission Link Level 1 TDM Time Division Multiplexing UC Unified Capabilities URL Uniform Resource Locator VVoIP Voice and Video over Internet Protocol 4

5 4. Test Details. The extension of this certification is based upon DTR 1. The original certification, documented in Reference (c), is based on interoperability testing, review of the vendor s Letters of Compliance (LoC), Defense Information Systems Agency (DISA) adjudication of open test discrepancy reports (TDRs), and DISA Certifying Authority (CA) Recommendation for inclusion on the UC APL. Testing was conducted at JITC s Global Information Grid Network Test Facility at Fort Huachuca, Arizona, from 26 August 2013 through 6 September 2013, using test procedures derived from Reference (e). Review of the vendor s LoC was completed on 16 August DISA adjudication of outstanding TDRs was completed on 1 October Information Assurance (IA) testing was conducted by DISA-led IA test teams and the results are published in a separate report, Reference (f). This DTR 1 was requested to upgrade the UCCP CUCM and CUPS from Release 8.6(1) ( ) to SU3, the Jabber from Release to 11.0, the 29xx and 39xx series MGs from Release IOS M2 to 15.6(2) T, and the 29xx and 39xx series SBCs from Release IOS M2 to IOS 15.5(3)M3. JITC analysis determined these components are the same as the components configured in the Cisco Enterprise Session Controller (ESC) 15, Reference (g), which has successfully completed certification testing. In addition, the SUT received a waiver from DoD CIO for IPv6 with release Cisco Unified Communication Manager (CUCM) and Cisco Unified Presence Server (CUPS) Release 8.6(1) ( ), and Jabber Release This DTR1 updates the CUCM and CUPS to Release SU3, and Cisco Jabber for Windows to Release 11.0, which were included in the Cisco ESC15 IO certification letter, Reference (g) and determined by JITC to be IPv6 compliant. Therefore, based on JITC analysis the DoD CIO IPv6 is no longer relevant to the SUT. Also, the DISA UC Certification Office concurred that no additional IA testing was required on the SUT because the security testing on the updated components was conducted and approved by DISA on the Cisco ESC15, Reference (h), which is functionally the same as the SUT. Therefore, the JITC approves this DTR without any additional IA or interoperability testing. 5. Additional Information. JITC distributes interoperability information via the JITC Electronic Report Distribution (ERD) system, which uses Sensitive but Unclassified IP Data (formerly known as NIPRNet) . Interoperability status information is available via the JITC System Tracking Program (STP). STP is accessible by.mil/.gov users at Test reports, lessons learned, and related testing documents and references are on the JITC Joint Interoperability Tool (JIT) at Due to the sensitivity of the information, the Information Assurance Accreditation Package (IAAP) that contains the approved configuration and deployment guide must be requested directly from the Unified Capabilities Certification Office (UCCO), disa.meade.ie.list.unified-capabilitiescertification-office@mail.mil. All associated information is available on the DISA UCCO website located at 6. Point of Contact (POC). The JITC point of contact is Mr. Joseph Schulte, commercial telephone (520) , DSN telephone , FAX DSN ; address joseph.t.schulte.civ@mail.mil; mailing address Joint Interoperability Test Command, ATTN: 5

6 JTE (Mr. Joseph Schulte) P.O. Box 12798, Fort Huachuca, AZ The UCCO tracking number for the SUT is FOR THE COMMANDER: Enclosures a/s RIC HARRISON Chief Networks/Communications and UC Division Distribution (electronic mail): DoD CIO Joint Staff J-6, JCS USD(AT&L) ISG Secretariat, DISA, JTA U.S. Strategic Command, J665 US Navy, OPNAV N2/N6FP12 US Army, DA-OSA, CIO/G-6 ASA(ALT), SAIS-IOQ US Air Force, A3CNN/A6CNN US Marine Corps, MARCORSYSCOM, SIAT, A&CE Division US Coast Guard, CG-64 DISA/TEMC DIA, Office of the Acquisition Executive NSG Interoperability Assessment Team DOT&E, Netcentric Systems and Naval Warfare Medical Health Systems, JMIS IV&V HQUSAISEC, AMSEL-IE-IS UCCO 6

7 ADDITIONAL REFERENCES (c) Joint Interoperability Test Command, Memo, JTE, Joint Interoperability Certification of the Cisco Unified, 21 January 2014 (d) Office of the Department of Defense Chief Information Officer, Department of Defense Unified Capabilities Requirements 2013, Errata 1, 1 July 2013 (e) Joint Interoperability Test Command, Unified Capabilities Collaboration Product Test Procedures for UCR 2013 (Draft) (f) Joint Interoperability Test Command, Information Assurance (IA) Findings Summary For Cisco Unified Capabilities (UC) Collaboration Product (CP) (UCCP) 8 Tracking Number , September 2016 (g) Joint Interoperability Test Command, Memo, JTE, Joint Interoperability Certification of the Cisco Enterprise Session Controller (ESC) 15 Release , 17 December 2015 (with all Desktop Reviews as of 20 Sept. 2016) (h) Joint Interoperability Test Command, Information Assurance (IA) Findings Summary For Cisco Enterprise Session Controller (ESC) 15 Release 10.5 Tracking Number , August 2016 Enclosure