HPE Moonshot ilo Chassis Management Firmware 1.52 Release Notes

Transcription

1 HPE Moonshot ilo Chassis Management Firmware 1.52 Release Notes Part Number: Published: February 2017 Edition: 1

2 2017 Hewlett Packard Enterprise Development LP Notices The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein. Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR and , Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise website.

3 Release Notes Description The HPE Moonshot ilo Chassis Management Firmware is the gateway for aggregated chassis management on the HPE Moonshot System. As a single point of access to the chassis, Moonshot ilo CM firmware allows you to configure, update, and operate HPE Moonshot via CLI, IPMI, web interface, and remote serial console access. Update recommendation Recommended - Includes major updates. Supersede information Supersedes: Moonshot ilo Chassis Management Firmware 1.50/1.51 Product models This release applies to the HPE Moonshot 1500 Chassis Management module. Devices supported Installation of this release supports the following devices: Moonshot 1500 Chassis HPE ProLiant Moonshot Server HPE ProLiant m300 Server Cartridge HPE ProLiant m400 Server Cartridge HPE ProLiant m510 Server Cartridge HPE ProLiant m700 Server Cartridge HPE ProLiant m710 Server Cartridge HPE ProLiant m710x Server Cartridge HPE ProLiant m800 Server Cartridge HPE Moonshot-45G Switch Module HPE Moonshot-180G Switch Module HPE Moonshot Remote Console Administrator (mrca) Operating systems The release is not OS-dependent. Enhancements made the following CLI enhancements: Added the following commands: Release Notes 3

4 SET NODE ASSET SHOW NODE ASSET SET SNMP TRAPPORT Updated the command output of the following to include additional information: SHOW SNMP Now includes the configured SNMP trap port. SHOW NODE LIST Now includes a column titled Node Asset Tag. SHOW NODE INFO Now includes node asset tag. Modified the access privilege for SET CARTRIDGE ASSET from administrator to operator. Table 1: New and changed commands in Moonshot ilo CM firmware v1.52 New commands SHOW NODE ASSET SET NODE ASSET SET SNMP TRAPPORT Changed commands (change type) SHOW SNMP (output) SHOW NODE LIST (output) SET CARTRIDGE ASSET (access privilege) Fixes added the following features: Added Node Asset tags in the GUI, CLI, IPMI, and RESTful interfaces. Added the ability to configure the SNMP trap port via the CLI and RESTful interfaces. Added a new set of RESTful calls to control the power and the boot device for multiple nodes with a single POST to /rest/v1/systemssummary. Added check at cartridge insertion for no memory DIMMs present. If no DIMM is present, the message Error: Memory error detected by population rules (00) will be added to the IML log. The "00" indicates no DIMMs present. Any other number indicates a DIMM is present but in the wrong connector. Hewlett Packard Enterprise has also to included the following enhancements to the HPE Moonshot ilo Chassis Management in v1.52: The firmware now discovers and shows NVMe drives on ilo-based cartridges in the both web interface and CLI (feature requires ilo Moonshot v2.50 or later.) Shortened the rendering time of the Show Links page in the GUI and added a table of all current links to the page. Enhanced IML log entries to identify the node number in wear level log messages. The cartridge number was identified, but node number was not previously identified. Enhanced the Edit Links page in the GUI. Hovering over the link icon on a cartridge shows a table of all current and all possible links for the cartridge. Selecting a cartridge shows a table with all current links for the cartridge. Modified chassis fan table to meet NEBS compliance. Updated the CLI version reported in the CLI to 2.5. resolved the following: Boot settings and some security settings being lost on ilo CM 1.50 or 1.51 upgrades. The SET CARTRIDGE ASSET command possibly corrupting FRU data on a cartridge if it was used to configure many cartridges with the same tag with one command. 4 Fixes

5 Intermittent invalid reporting of a memory error in the IML log for "Memory error detected by population rules" for m700p cartridges. The CLI command SHOW CARTRIDGE POWER reporting wrong node power states. It was reporting the node power state for the next higher node. Handling of empty SNMP trap targets to avoid long delays. Physical pressing of the UID button on a cartridge cannot result in ilo CM showing the wrong state of the UID light. Updated security to Openssl 1.0.1u. Improvements in the REST call for ColdReset (force power off, followed by queueing of a power on) of a node by allowing longer for the power down transition. Made sure unset Cartridge Asset Tags are never displayed. UUIDs of nodes 2-4 sometimes showing the node 1 UUID. Modified SSH handling so that command output from a CLI RUN command can be obtained in full, keeping the session from sending an EOF after the first command in the script completes. This is applicable when running CLI commands over SSH via automated scripts. Potential problem with SSH connection handling with multiple active users. HPE Moonshot 180GXc switch sometimes showing a temp of 255 degrees for sensor "05-Net Ctrlr 2". Documentation feedback Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page. Documentation feedback 5