DECUS IT-Symposium Spanning Tree Protocol Interoperability Cisco/HP ProCurve

Size: px
Start display at page:

Download "DECUS IT-Symposium Spanning Tree Protocol Interoperability Cisco/HP ProCurve"

Transcription

1 DECUS IT-Symposium 2006 Spanning Tree Protocol Interoperability Cisco/HP ProCurve Juergen Bruns Network Competency Center EMEA HP Services 2003 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice Agenda Protocol refresh IEEE802.1D PVST+ IEEE802.1w IEEE802.1s Cisco STP ProCurve STP Configuration Example page 2 1

2 Requirements for a Layer 2 redundancy protocol Provide a loopfree topology, meaning a packet should never be seen twice in a network Only ONE active path between two hosts Should activate redundant links in case of a failure Convergence time should be as quick as possible Nice to have: Utilize redundant links page 3 Preventing Bridging Loops Neither Switch A or B running STP Station A / /1 Segment A 1/2 3 2/2 4 7 Segment B Station B page 4 2

3 Preventing Bridging Loops Bridging loops can be prevented by disabling the redundant path Station A Segment A 1/1 2/1 1/2 Segment B 2/2 Station B page 5 STP and IEEE Standards The First IEEE standard implementation of STP is IEEE 802.1D. (since 1998) RSTP is Rapid Spanning-Tree Protocol defined by the IEEE 802.1w. (since 2001) MSTP is Multiple Spanning-Tree Protocol defined by the IEEE 802.1s. (since 2002/2003, Standard Compliance on Cisco since 2006) Cisco proprietär PVST is Per VLAN Spanning-tree proprietary implementation of STP on Cisco equipment using a ISL trunk. (Rapid) - PVST+ is the implementation of PVST on 802.1q links. IEEE 802.1s Vlan MST based on a pre-standards draft. page 6 3

4 STP Calculating a loop free network 1. Select the Root bridge => lowest Bridge ID (Bridge Prio + Bridge Mac) 2. Select Root ports, 1 per Bridge => shortest path to root 3. Select Designated port, 1 per Segment => shortest path to root => Lowest Sender Bridge ID used as tie-breaker 4. Use Port ID as tie-breaker => lowest Port ID (Port Prio + System #) page 7 Which port is blocking? Switch A Gbit/s Gbit/s Switch B 0 Mbit/s Brigde MAC (A=x1, B=x2, C=x3) Bridge Prio (default: 32768) Port cost (default: Gbit/s=4, 0Mbit/s=19) Path cost (sum of all port costs to root) Port priority (default = 32) Switch C page 8 4

5 802.1D root bridge election The Bridge/Switch having the lowest Bridge ID is the Root Bridge The Bridge Priority, default to 32768, is configurable. Root Bridge ABCD DE BPDUs 2 bytes 6 bytes AC EF88 Priority Bridge ID MAC Address page D root port election Each bridge retains the lowest cost to reach the Root bridge, on each port. The best port (Root Port) is then elected: Root Port Link Cost page 5

6 802.1D designated port For each segment, only the best path is used towards the Root Bridge. The corresponding port is called the Designated Port (). Redundant Bridges are blocked. Cost=0 A Hub B page D logical topology Topology becomes loopfree Hub A B page 12 6

7 802.1D and 802.1t 802.1D port costs (16 Bit) Port Speed Mbps 0 Mbps 1 Gbps Default Cost Value Default Range 1 to to to t port costs (32 Bit) used for IEEE 802.1w and IEEE 802.1s Port Speed Recommended Value Recommended Range Available Range > 0 kbps to to Mbps to to Mbps to to Mbps to to Gbps to to Gbps to to page 13 Per VLAN Spanning Tree (PVST+) Cisco s implementation of STP Cisco switches run per-vlan Spanning tree Each VLAN builds its own STP instance (<128) Provides loadbalancing No standard, but compatible with 802.1D CST BPDUs are send untagged in VLAN1, even if the native VLAN is not = VLAN 1 Shared Spanning Tree BPDUs are sent tagged for each VLAN (exept for the native VLAN) to MAC: 00.0ccc.cccd page 14 7

8 PVST+ Loadbalancing Sample Topology for VLAN : Hub A B page 15 PVST+ Loadbalancing Sample Topology for VLAN 20: Hub A B page 16 8

9 802.1D protocol states Time 20 Sec 15 Sec 15 Sec Blocking Max-Age Listening Forward Delay Learning Forward Delay Forwarding page 17 Rapid Spanning Tree 802.1w Overview Extension to 802.1D => higher convergence speed. Includes features similar to UplinkFast, Backbone Fast and PortFast. New Port Role Modified BPDU Rapid port state transition. New topology change mechanism D Compatibility IEEE 802.1w - a standard since June Rapid PVST+ has the same architecture as PVST+ except that it uses 802.1W rapid STP protocol instead of 802.1D page 18 9

10 802.1w port roles 4 port roles Root port: shortest path to the root bridge in terms of path costs (Forwarding) Designated port: the port which is sending the best PBDU for a segment (Forwarding) Alternate Port: an port which has an alternative path to the root bridge (Blocking = Discarding) Backup Port: Port which has link to the same segment on the same switch (Blocking = Discarding) page w port roles Port roles RP = Root port = Designated Port AP = Alternate Port BP = Backup Port RP Hub A RP AP AP BP B HUB page 20

11 Multi Instance Spanning Tree IEEE 802.1s Features The latest Spannng Tree standard Fast convergence Can make use of all links in network Makes STP scalable page s Before (802.1D or 802.1w) Before (with PVST) Root of 3 VLANs 1 VLANs 2 VLANs 3 VLANs 1 VLANs 2 VLANs 3 VLANs 1 VLANs 2 VLANs 3 VLANs 1 VLANs 2 VLANs 3 Root VLANs 1 VLANs 2 VLANs 3 Root of 1 Now with 802.1s VLANs 1 Root of 2 VLANs 2 VLANs 3 VLANs 1,2 VLAN 3,4 VLANs 1,2 VLAN 3,4 MSTI-1 Root VLANs 1,2 VLAN 3,4 MSTI-2 Root page 22 11

12 802.1s Terms MST Region: a group of switches running 802.1s under commen set of configuration attributes MST instance: an entity which will calculate his own topology. Each instance can be used for one or more VLANs Common Spanning Tree (CST): An STP or RSTP spanning tree instance to interconnect differrent regions Internal Spanning Tree (IST): RSTP instance interconnecting CST to the region. All ohter VLANs that are not configured manualy to an instance are mapped automatically to the IST = MST Instance 0. page s Terms CST MST Region IST page 24 12

13 MSTP - Configuring Regions - ProCurve MSTP - Configuring Regions for ProCurve To create multiple spanning tree instances, an MST "region" is defined, with 3 parameters that must be identical for each switch in the region: region name ("spanning-tree config-name") revision number ("spanning-tree config-revision") VLAN-to-instance mapping ("span instance <1-16> vlan <VID>") Each VLAN can be a member of only 1 MST instance. Any VLANs not claimed by (not configured in) an MST instance automatically exist in instance 0 (the Internal Spanning Tree, or IST), which always exists when MSTP is enabled. page 25 Summary and Guide-line page 26 13

14 Cisco vs ProCurve STP Protocols Cisco IOS switch can run the following protocols: Common Spanning Tree (IEEE 802.1D) PVST+ Rapid PVST+ (default) MSTP IEEE 802.1s draft MSTP IEEE 802.1s Standard Compliance ProCurve Switch can enable the following protocols: Common Spanning Tree (IEEE 802.1D) PVST+ (only 9300 Series) Rapid STP (IEEE 802.1w) per box (default) MSTP IEEE 802.1s Standard Compliance page 27 Interoperability Cisco & ProCurve Try to use the MSTP IEEE802.1s Standard Compliance Version on Cisco and enable MSTP on ProCurve Try to build at least one region. It will act as a virtual bridge. Between the regions or to other STP Bidges the "Common Spanning Tree" (CST) is the active tree. In IEEE802.1s the CST can use Rapid STP or the older version.1d When connection a MST Region to (rapid) - PVST+ device be aware that the CST is running untagged on VLAN1 regardless of the native vlan. Check the STP cost setting when connecting a IEEE802.1s or. 1w configuration to a Cisco Rapid PVST+ or.1d bridge. You can revert the cost on ProCurve to the legacy settings. page 28 14

15 Cisco MSTP IEEE 802.1s Standard Compliance Device Required IOS Cisco Catalyst 2950, 3550, IOS 12.2(25)SEC 3560, 3750 Cisco Catalyst IOS 12.2(25)SG 4000 No CatOS version Cisco Catalyst IOS 12.2(18)SXF 6000 or CatOS 8.3 Please refer to Cisco Website and select the Software Advisor Tool page 29 Example Configuring MSTP on ProCurve/Cisco Sample topology Parameters for the MSTP are as follows: Config Name: hp-cisco Config Revision #: 1 Instance 1 VLAN 1,,20 Instance 2 VLAN 30,40 Cisco-1 is Root for instances 0 (IST) and 1 Cisco-2 is Root for instance 2 HP ProCurve switches, ProCurve- Edge-1 and 2, are defined as edge switches page 30 15

16 Configuring MSTP on Cisco The Cisco Switch 1 is defined as Root for instances 0 (IST) and 1, and secondary Root for instance 2. Conf t hostname Cisco-1 Spanning-Tree mode mst Spanning-Tree extend system-id! Spanning-Tree mst configuration name hp-cisco revision 1 instance 1 vlan 1,, 20 instance 2 vlan 30, 40 Spanning-Tree mst 0-1 priority 0 Spanning-Tree mst 2 priority 4096 end The Cisco Switch 2 is defined as Root for instances 2 and secondary Root for instance 0 and 1. Conf t hostname Cisco-2 Spanning-Tree mode mst Spanning-Tree extend system-id! Spanning-Tree mst configuration name hp-cisco revision 1 instance 1 vlan 1,, 20 instance 2 vlan 30, 40! Spanning-Tree mst 0-1 priority 4096 Spanning-Tree mst 2 priority 0 page 31 Configuring MSTP on ProCurve ProCurve-Edge-1 and 2 are defined as edge switches. hostname "ProCurve-Edge-1/2" Spanning-Tree Spanning-Tree protocol-version MSTP Spanning-Tree config-name "hp-cisco" Spanning-Tree config-revision 1 Spanning-Tree instance 1 vlan 1 20 Spanning-Tree instance 2 vlan Result Cisco-1#sh span mst configuration Name [hp-cisco] Revision 1 Instance Vlans mapped ,11-19,21-29,31-39, ,, , page 32 16

17 Useful Cisco Troubleshooting Commands CatOS sh spant summary (summary of features / ports) sh spant <vlan> active (STP state for a vlan) sh spant mst [inst] (STP state for MST instance) sh spant <mod/port> (STP state for port) sh spant stat <mod/port> <vlan> IOS sh spann summary sh spann vlan <vlan> detail sh spann mst [inst] sh spann int <int> detail sh span int <int> detail page 33 Summary Create a STP Design, Test and Implementation Plan Try to use the IEEE 802.1s Standard Compliance Version Check the lastest FW or IOS versions Check the Common Spanning Tree settings When using PVST+ take care for VLAN1 If the STP is stable, secure it using BPDU Guard, Root Guard page 34 17

18 HP logo THE END Vielen Dank!!! 18

The multiple spanning-tree (MST) implementation is based on the IEEE 802.1s standard.

The multiple spanning-tree (MST) implementation is based on the IEEE 802.1s standard. CHAPTER 18 This chapter describes how to configure the Cisco implementation of the IEEE 802.1s Multiple STP (MSTP) on the IE 3010 switch. Note The multiple spanning-tree (MST) implementation is based on

More information

Configuring MSTP CHAPTER

Configuring MSTP CHAPTER CHAPTER 16 Configuring MSTP This chapter describes how to configure the Cisco implementation of the IEEE 802.1s Multiple STP (MSTP) on the Catalyst 2960 switch. Note The multiple spanning-tree (MST) implementation

More information

Cisco Exam Interconnecting Cisco Networking Devices Part 2 Version: 10.0 [ Total Questions: 149 ]

Cisco Exam Interconnecting Cisco Networking Devices Part 2 Version: 10.0 [ Total Questions: 149 ] s@lm@n Cisco Exam 200-101 Interconnecting Cisco Networking Devices Part 2 Version: 10.0 [ Total Questions: 149 ] Topic break down Topic No. of Questions Topic 1: LAN Switching Technologies 18 Topic 2:

More information

Spanning-Tree Protocol

Spanning-Tree Protocol Spanning-Tree Protocol Malin Bornhager Halmstad University Session Number 2002, Svenska-CNAP Halmstad University 1 Objectives Redundancy in a converged network Spanning-Tree Protocol (STP) STP Operation

More information

Configuring STP and Prestandard IEEE 802.1s MST

Configuring STP and Prestandard IEEE 802.1s MST 20 CHAPTER This chapter describes how to configure the Spanning Tree Protocol (STP) and prestandard IEEE 802.1s Multiple Spanning Tree (MST) protocol on Catalyst 6500 series switches. Note The IEEE 802.1s

More information

Configuring Spanning Tree Protocol

Configuring Spanning Tree Protocol Finding Feature Information, page 1 Restrictions for STP, page 1 Information About Spanning Tree Protocol, page 2 How to Configure Spanning-Tree Features, page 14 Monitoring Spanning-Tree Status, page

More information

Layer 2 Engineering Spanning Tree

Layer 2 Engineering Spanning Tree Layer 2 Engineering Spanning Tree Campus Network Design & Operations Workshop These materials are licensed under the Creative Commons Attribution-NonCommercial 4.0 International license (http://creativecommons.org/licenses/by-nc/4.0/)

More information

Configuring Spanning Tree Protocol

Configuring Spanning Tree Protocol Restrictions for STP Restrictions for STP, on page 1 Information About Spanning Tree Protocol, on page 1 How to Configure Spanning-Tree Features, on page 13 Monitoring Spanning-Tree Status, on page 25

More information

Configuring STP and RSTP

Configuring STP and RSTP 7 CHAPTER Configuring STP and RSTP This chapter describes the IEEE 802.1D Spanning Tree Protocol (STP) and the ML-Series implementation of the IEEE 802.1W Rapid Spanning Tree Protocol (RSTP). It also explains

More information

Configuring STP. Understanding Spanning-Tree Features CHAPTER

Configuring STP. Understanding Spanning-Tree Features CHAPTER CHAPTER 11 This chapter describes how to configure the Spanning Tree Protocol (STP) on your switch. For information about the Rapid Spanning Tree Protocol (RSTP) and the Multiple Spanning Tree Protocol

More information

Chapter 5: STP. * What is STP? How does STP work?

Chapter 5: STP. * What is STP? How does STP work? Chapter 5: STP * What is STP? How does STP work? * What would be the worst case scenario that could happen to a redundant path switched network with the STP is disabled? When multiple paths exist between

More information

Table of Contents. (Rapid) Spanning Tree Protocol. A simple bridge loop. An even worse bridge loop. Bridge loops Two bridges Three bridges (R)STP

Table of Contents. (Rapid) Spanning Tree Protocol. A simple bridge loop. An even worse bridge loop. Bridge loops Two bridges Three bridges (R)STP Table of Contents (Rapid) Spanning Tree Protocol (R)STP Karst Koymans Informatics Institute University of Amsterdam (version 18.4, 2018/11/16 13:23:04) Friday, November 16, 2018 Bridge loops Two bridges

More information

Spanning-Tree Protocol

Spanning-Tree Protocol Spanning-Tree Protocol Agenda» What Problem is Solved by STP?» Understanding STP Root Bridge Election» BPDU Details and Pathcost» Understanding STP Root and Designated Port Election» Understanding and

More information

Table of Contents 1 MSTP Configuration 1-1

Table of Contents 1 MSTP Configuration 1-1 Table of Contents 1 MSTP Configuration 1-1 Overview 1-1 Introduction to STP 1-1 Why STP 1-1 Protocol Packets of STP 1-1 Basic Concepts in STP 1-2 How STP works 1-3 Introduction to RSTP 1-9 Introduction

More information

PASS4TEST. IT Certification Guaranteed, The Easy Way! We offer free update service for one year

PASS4TEST. IT Certification Guaranteed, The Easy Way!   We offer free update service for one year PASS4TEST IT Certification Guaranteed, The Easy Way! \ http://www.pass4test.com We offer free update service for one year Exam : 351-001 Title : CCIE Cisco Certified InterNetworking Expert Vendors : Cisco

More information

Configuring Rapid PVST+

Configuring Rapid PVST+ This chapter describes how to configure the Rapid per VLAN Spanning Tree (Rapid PVST+) protocol on Cisco NX-OS devices using Cisco Data Center Manager (DCNM) for LAN. For more information about the Cisco

More information

Understanding and Configuring STP

Understanding and Configuring STP CHAPTER 14 This chapter describes how to configure the Spanning Tree Protocol (STP) on a Catalyst 4500 series switch. It also provides guidelines, procedures, and configuration examples. This chapter includes

More information

Configuring Rapid PVST+ Using NX-OS

Configuring Rapid PVST+ Using NX-OS Configuring Rapid PVST+ Using NX-OS This chapter describes how to configure the Rapid per VLAN Spanning Tree (Rapid PVST+) protocol on Cisco NX-OS devices. This chapter includes the following sections:

More information

Campus Networking Workshop. Layer 2 engineering Spanning Tree and VLANs

Campus Networking Workshop. Layer 2 engineering Spanning Tree and VLANs Campus Networking Workshop Layer 2 engineering Spanning Tree and VLANs Switching Loop When there is more than one path between two switches What are the potential problems? Switching Loop If there is more

More information

MSTP Configuration. Page 1 of 24

MSTP Configuration. Page 1 of 24 MSTP Configuration Page 1 of 24 Contents Chapter1 Configuring MSTP... 3 1.1 Brief Introduction to MSTP...3 1.2 BPDU...3 1.2.1 Basic Concepts in MSTP... 4 1.2.2 Roles of Ports... 6 1.3 Algorithm Implementation...9

More information

Table of Contents. (Rapid) Spanning Tree Protocol. A simple bridge loop. An even worse bridge loop. Bridge loops Two bridges Three bridges (R)STP

Table of Contents. (Rapid) Spanning Tree Protocol. A simple bridge loop. An even worse bridge loop. Bridge loops Two bridges Three bridges (R)STP Table of Contents (Rapid) Spanning Tree Protocol (R)STP Karst Koymans Informatics Institute University of Amsterdam (version 34, 2014/02/17 14:41:48) Monday, February 17, 2014 Bridge loops Two bridges

More information

MSTP Configuration. Configuration

MSTP Configuration. Configuration MSTP Configuration Contents 1. Configuring MSTP...2 1.1 Brief Introduction to MSTP... 2 1.2 BPDU... 2 1.2.1 Basic Concepts in MSTP...2 1.2.2 Roles of Ports...4 1.3 Algorithm Implementation... 7 1.3.1 MSTP

More information

Index. Numerics. Index p priority (QoS) definition Q VLAN standard w as a region 5-54

Index. Numerics. Index p priority (QoS) definition Q VLAN standard w as a region 5-54 Index Numerics 802.1p priority (QoS) 802.1Q VLAN standard 5-7 802.1w as a region 5-54 A active path 5-5 address IP 7-8 advertisement 3-3 applicable products 1-ii ARP age setting 7-10 cache 7-4 cache table

More information

Configuring Rapid PVST+

Configuring Rapid PVST+ This chapter contains the following sections: Information About Rapid PVST+, page 1, page 16 Verifying the Rapid PVST+ Configuration, page 24 Information About Rapid PVST+ The Rapid PVST+ protocol is the

More information

CCNA 3 (v v6.0) Chapter 3 Exam Answers % Full

CCNA 3 (v v6.0) Chapter 3 Exam Answers % Full CCNA 3 (v5.0.3 + v6.0) Chapter 3 Exam Answers 2017 100% Full ccnav6.com /ccna-3-v5-0-3-v6-0-chapter-3-exam-answers-2017-100-full.html CCNA Exam Answers 2017 CCNA 3 (v5.0.3 + v6.0) Chapter 3 Exam Answers

More information

Cisco Understanding Multiple Spanning Tree Protocol (802.1

Cisco Understanding Multiple Spanning Tree Protocol (802.1 Cisco Understanding Multiple Spanning Tree Protocol (802.1 Table of Contents Understanding Multiple Spanning Tree Protocol (802.1s)...1 Introduction...1 Where to use MST...2 PVST+ Case...2 Standard 802.1q

More information

Spanning Tree Protocol(STP)

Spanning Tree Protocol(STP) Introduction Spanning Tree Protocol (STP) is a Layer 2 protocol that runs on bridges and switches. The specification for STP is IEEE 802.1D. The main purpose of STP is to ensure that you do not create

More information

Implement Spanning Tree Protocols. LAN Switching and Wireless Chapter 5

Implement Spanning Tree Protocols. LAN Switching and Wireless Chapter 5 Implement Spanning Tree Protocols LAN Switching and Wireless Chapter 5 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Objectives Explain the role of redundancy in a converged

More information

MSTP Technology White Paper

MSTP Technology White Paper MSTP Technology White Paper Key words: STP, RSTP, MSTP, rapid transition, multiple instances, redundancy loop, redundancy link, load sharing Abstract: This article introduces basic MSTP terms, MSTP algorithm

More information

Understanding Multiple Spanning Tree Protocol (802.1s)

Understanding Multiple Spanning Tree Protocol (802.1s) Understanding Multiple Spanning Tree Protocol (802.1s) Document ID: 24248 Introduction Where to Use MST PVST+ Case Standard 802.1q Case MST Case MST Region MST Configuration and MST Region Region Boundary

More information

Configuring Optional Spanning-Tree Features

Configuring Optional Spanning-Tree Features CHAPTER 20 This chapter describes how to configure optional spanning-tree features on the Catalyst 3750-E or 3560-E switch. You can configure all of these features when your switch is running the per-vlan

More information

Table of Contents. (Rapid) Spanning Tree Protocol. An even worse bridge loop. A simple bridge loop. Bridge loops Two bridges Three bridges (R)STP

Table of Contents. (Rapid) Spanning Tree Protocol. An even worse bridge loop. A simple bridge loop. Bridge loops Two bridges Three bridges (R)STP Table of Contents (Rapid) Spanning Tree Protocol (R)STP Karst Koymans Informatics Institute University of Amsterdam (version 44, 2015/02/18 12:55:30) Thursday, February 19, 2015 Bridge loops Two bridges

More information

Configuring MST Using Cisco NX-OS

Configuring MST Using Cisco NX-OS This chapter describes how to configure Multiple Spanning Tree (MST) on Cisco NX-OS devices. This chapter includes the following sections: Finding Feature Information, page 1 Information About MST, page

More information

Copyright 2014 CertificationKits LLC. All Rights Reserved. 2

Copyright 2014 CertificationKits LLC. All Rights Reserved. 2 Copyright 2014 CertificationKits LLC. All Rights Reserved. 2 Spanning Tree Protocol is a bridge protocol that enables a learning bridge to dynamically work around loops in a network topology by creating

More information

HP0-Y12. Building ProCurve Resilient, Adaptive Networks. Download Full Version :

HP0-Y12. Building ProCurve Resilient, Adaptive Networks. Download Full Version : HP HP0-Y12 Building ProCurve Resilient, Adaptive Networks Download Full Version : https://killexams.com/pass4sure/exam-detail/hp0-y12 QUESTION: 106 The output of show ip ospf link-state on a ProCurve Switch

More information

Question No : 1 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

Question No : 1 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.) Volume: 149 Questions Question No : 1 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.) A. 802.1Q native VLAN frames are untagged by default. B. 802.1Q trunking ports

More information

Managing Network Spanning Trees

Managing Network Spanning Trees CHAPTER 8 This chapter describes, the IEEE 802.1d Spanning Tree Protocol (STP), and how to use and configure Cisco s proprietary spanning-tree protocols, Per VLAN Spanning Tree (PVST), Multiple Spanning

More information

Table of Contents Chapter 1 MSTP Configuration

Table of Contents Chapter 1 MSTP Configuration Table of Contents Table of Contents... 1-1 1.1 MSTP Overview... 1-1 1.1.1 MSTP Protocol Data Unit... 1-1 1.1.2 Basic MSTP Terminologies... 1-2 1.1.3 Implementation of MSTP... 1-6 1.1.4 MSTP Implementation

More information

Implementing MST in a Large Campus Environment

Implementing MST in a Large Campus Environment Implementing MST in a Large Campus Environment February 13, 2007 Rich Ingram rni@umn.edu Overview Introduction Multiple Spanning Tree Protocol Our Implementation Introduction U of M Twin Cities Campus

More information

Chapter 5. Spanning Tree Protocol (STP) Part II

Chapter 5. Spanning Tree Protocol (STP) Part II Chapter 5 Spanning Tree Protocol (STP) Part II CCNA3-1 Chapter 5-2 Note for Instructors These presentations are the result of a collaboration among the instructors at St. Clair College in Windsor, Ontario.

More information

BLADE 802.1s Spanning Tree and Interoperability with Cisco

BLADE 802.1s Spanning Tree and Interoperability with Cisco BLADE 802.1s Spanning Tree and Interoperability with Cisco Technical Brief Industry-standard 802.1s Multiple Spanning Tree Protocol with Cisco interoperability for HP GbE2/GbE2c Ethernet Blade Switches

More information

HP0-Y23. Deploying HP ProCurve Products.

HP0-Y23. Deploying HP ProCurve Products. HP HP0-Y23 Deploying HP ProCurve Products http://killexams.com/exam-detail/hp0-y23 QUESTION: 62 You enter the following command at the CLI of an HP ProCurve 3500yl switch: 3500yl (config)# spanning-tree

More information

62HConfiguring port role restriction 131H37. 63HConfiguring TC-BPDU transmission restriction 132H38. 64HEnabling TC-BPDU guard 133H38

62HConfiguring port role restriction 131H37. 63HConfiguring TC-BPDU transmission restriction 132H38. 64HEnabling TC-BPDU guard 133H38 Contents Configuring spanning tree protocols 3 STP 3 STP protocol packets 3 Basic concepts in STP 4 Calculation process of the STP algorithm 5 RSTP 9 MSTP 10 MSTP features 10 MSTP basic concepts 10 How

More information

Layer 2/3 Configuration Guide, Cisco IOS XE Release 3.6E (Catalyst 3850 Switches)

Layer 2/3 Configuration Guide, Cisco IOS XE Release 3.6E (Catalyst 3850 Switches) Layer 2/3 Configuration Guide, Cisco IOS XE Release 3.6E (Catalyst 3850 Switches) First Published: June 27, 2014 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706

More information

Describing the STP. 2003, Cisco Systems, Inc. All rights reserved. 2-1

Describing the STP. 2003, Cisco Systems, Inc. All rights reserved. 2-1 Describing the STP 2003, Cisco Systems, Inc. All rights reserved. 2-1 IEEE Documents IEEE 802.1D IEEE 802.1Q IEEE 802.1w IEEE 802.1s - Media Access Control (MAC) bridges - Virtual Bridged Local Area Networks

More information

Implement Spanning Tree Protocols PART-II. LAN Switching and Wireless Chapter 5 Modified by Tony Chen 07/01/2009

Implement Spanning Tree Protocols PART-II. LAN Switching and Wireless Chapter 5 Modified by Tony Chen 07/01/2009 Implement Spanning Tree Protocols PART-II LAN Switching and Wireless Chapter 5 Modified by Tony Chen 07/01/2009 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Notes: If you

More information

Configuring STP Extensions

Configuring STP Extensions Configuring STP Extensions This chapter describes the configuration of extensions to the Spanning Tree Protocol (STP) on Cisco Nexus 5000 Series switches. It includes the following sections: About STP

More information

STP Optional Characteristic Configuration

STP Optional Characteristic Configuration Table of Contents Table of Contents Chapter 1 Configuring STP Optional Characteristic... 1 1.1 STP Optional Characteristic Introduction... 1 1.1.1 Port Fast... 1 1.1.2 BPDU Guard... 2 1.1.3 BPDU Filter...

More information

Download: PT-Topology-STP2.pkt

Download: PT-Topology-STP2.pkt IEEE Documents Describing the STP IEEE 802.1D IEEE 802.1Q IEEE 802.1w IEEE 802.1s - Media Access Control (MAC) bridges - Virtual Bridged Local Area Networks - Rapid Reconfiguration (Supp. to 802.1D) -

More information

Implementing Multiple Spanning Tree Protocol

Implementing Multiple Spanning Tree Protocol Implementing Multiple Spanning Tree Protocol This module provides conceptual and configuration information for Multiple Spanning Tree Protocol on Cisco ASR 9000 Series Routers. Multiple Spanning Tree Protocol

More information

material. For more information on how to get additional questions, please see

material. For more information on how to get additional questions, please see Review Questions The following questions are designed to test your understanding of this chapter s material. For more information on how to get additional questions, please see www.lammle.com/ccn a. You

More information

Configuring Optional STP Features

Configuring Optional STP Features CHAPTER 29 This chapter describes how to configure optional STP features. For complete syntax and usage information for the commands used in this chapter, see the Cisco IOS Master List, at this URL: http://www.cisco.com/en/us/docs/ios/mcl/allreleasemcl/all_book.html

More information

Introduction to OSPF

Introduction to OSPF Campus Networking Introduction to OSPF Workshop Campus Layer-2 Networking Network Workshop Design These materials are licensed under the Creative Commons Attribution-Noncommercial 3.0 Unported license

More information

CUDN PoP Switch Changes 2018

CUDN PoP Switch Changes 2018 CUDN PoP Switch Changes 2018 Agenda New PoP switch choices Port assignments Recommendations on connecting Spanning Tree now and changes How these will interact with your network DHCP Snooping & ARP Inspection

More information

Maintaining Specific VLAN Identification. Comparing ISL and 802.1Q. VLAN Trunking

Maintaining Specific VLAN Identification. Comparing ISL and 802.1Q. VLAN Trunking Maintaining Specific VLAN Identification Specifically developed for multi-vlan interswitch communications Places a unique identifier in each frame Functions at Layer 2 2003, Cisco Systems, Inc. All rights

More information

Describing the STP. IEEE Documents. Download this file. Enhancements to STP. Download: PT-Topology-STP2.pkt STP

Describing the STP. IEEE Documents. Download this file. Enhancements to STP. Download: PT-Topology-STP2.pkt STP IEEE Documents IEEE 802.1D IEEE 802.1Q IEEE 802.1w IEEE 802.1s - Media Access Control (MAC) bridges - Virtual Bridged Local Area Networks - Rapid Reconfiguration (Supp. to 802.1D) - Multiple Spanning Tree

More information

Index. Numerics. Index 1

Index. Numerics. Index 1 Index Numerics 802.1p priority (QoS) definition 8-6 802.1q VLAN in mesh 7-23 802.1Q VLAN standard 6-6 802.1w as a region 6-54 802.1x, mesh, not supported 7-5 A ABC enabled on edge switch 7-26 in mesh domain

More information

RealCiscoLAB.com. Observe what happens when the default spanning tree behavior is modified.

RealCiscoLAB.com. Observe what happens when the default spanning tree behavior is modified. RealCiscoLAB.com CCNPv6 SWITCH Modifying Default Spanning Tree Behavior Topology Objective Background Observe what happens when the default spanning tree behavior is modified. Four switches have just been

More information

CCNP SWITCH (22 Hours)

CCNP SWITCH (22 Hours) CCNP SWITCH 642-813 (22 Hours) Chapter-1 Enterprise Campus Network Design 1.1 IIN & SONA 1.2 Campus Network 1.3 Enterprise Model 1.4 Nonhierarchical Network Devices Layer-2 Switching, Layer-3 Routing Multilayer

More information

Understanding Rapid Spanning Tree Protocol (802.1w)

Understanding Rapid Spanning Tree Protocol (802.1w) Understanding Rapid Spanning Tree Protocol (802.1w) Contents Introduction Support of RSTP in Catalyst Switches New Port States and Port Roles Port States Port Roles New BPDU Format Full View of the Cisco

More information

Configuring STP Extensions

Configuring STP Extensions This chapter contains the following sections: Overview, page 1 Overview Cisco has added extensions to Spanning Tree Protocol (STP) that make convergence more efficient. In some cases, even though similar

More information

Exam Questions

Exam Questions Exam Questions 200-105 ICND2 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) https://www.2passeasy.com/dumps/200-105/ 1.At which layer of the OSI model is RSTP used to prevent loops? A. physical

More information

Buy full file at

Buy full file at 14 Chapter 2 LAN Redundancy Chapter 2 LAN Redundancy 2.0.1.2 Class Activity Stormy Traffic ( ) Objective Explain the purpose of the Spanning Tree Protocol (STP) in a switched LAN environment with redundant

More information

Document ID: Contents. Introduction. Prerequisites. Requirements. Components Used. Conventions. Background Information.

Document ID: Contents. Introduction. Prerequisites. Requirements. Components Used. Conventions. Background Information. Products & Services Spanning Tree from PVST+ to Rapid-PVST Migration Configuration Example Document ID: 72836 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information

More information

Abstract. GAK; Reviewed: WCH 8/14/2003. Solution & Interoperability Test Lab Application Notes 2003 Avaya Inc. All Rights Reserved.

Abstract. GAK; Reviewed: WCH 8/14/2003. Solution & Interoperability Test Lab Application Notes 2003 Avaya Inc. All Rights Reserved. Rapid Reconfiguration Spanning Tree Protocol (RSTP) 802.1w Sample Configurations for Avaya P882/P580 Gigabit Ethernet Switches with Third Party Vendors including Cisco, HP and Foundry - Issue 1.0 Abstract

More information

Table of Contents. Cisco Spanning Tree Protocol Enhancements using Loop Guard and BPDU Skew Detection Features

Table of Contents. Cisco Spanning Tree Protocol Enhancements using Loop Guard and BPDU Skew Detection Features Table of Contents Spanning Tree Protocol Enhancements using Loop Guard and BPDU Skew Detection Features...1 Document ID: 10596...1 Introduction...1 Feature Availability...1 Brief Summary of STP Port Roles...2

More information

The following graphic shows a single switch VLAN configuration.

The following graphic shows a single switch VLAN configuration. 7.1. VLAN A Virtual LAN (VLAN) can be defined as: Broadcast domains defined by switch port rather than network address. A grouping of devices based on service need, protocol, or other criteria rather than

More information

RSTP Configuration. Page 1 of 26

RSTP Configuration. Page 1 of 26 RSTP Configuration Page 1 of 26 Content Chapter 1 STP Configuration... 1 1.1 STP Overview... 1 1.1.1 Function of STP...1 1.1.2 Protocol Packets of STP...1 1.1.3 Basic Concepts in STP... 1 1.1.4 Spanning-Tree

More information

Spanning-Tree Protocol

Spanning-Tree Protocol Spanning-Tree Protocol Spanning Tree Protocol (IEEE 802.1D 1998), Rapid STP (IEEE 802.1D 2004), Cisco PVST+, MSTP Page 07-1 Agenda Spanning Tree Protocol (STP) Introduction Details Convergence Some more

More information

2.2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp ifindex clear. This command has no arguments or keywords.

2.2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp ifindex clear. This command has no arguments or keywords. Chapter 2 2.2 snmp ifindex clear snmp ifindex clear To clear any previously configured snmp ifindex commands that were entered for a specific interface, use the snmp ifindex clear command. snmp ifindex

More information

Improving network convergence with Multiple Spanning Tree Protocol

Improving network convergence with Multiple Spanning Tree Protocol CEAI, Vol.15, No.1 pp. 79-87, 2013 Printed in Romania Improving network convergence with Multiple Spanning Tree Protocol Roxana Stănică SC Civitas Systems S.R.L., Craiova, Romania (e-mail: roxana_batm@yahoo.com)

More information

Table of Contents. Cisco Understanding Rapid Spanning Tree Protocol (802.1w)

Table of Contents. Cisco Understanding Rapid Spanning Tree Protocol (802.1w) Table of Contents Understanding Rapid Spanning Tree Protocol (802.1w)...1 Introduction...1 Support of RSTP in Catalyst Switches...2 New Port States and Port Roles...2 Port States...2 Port Roles...3 New

More information

itexamdump 최고이자최신인 IT 인증시험덤프 일년무료업데이트서비스제공

itexamdump 최고이자최신인 IT 인증시험덤프   일년무료업데이트서비스제공 itexamdump 최고이자최신인 IT 인증시험덤프 http://www.itexamdump.com 일년무료업데이트서비스제공 Exam : 642-813 Title : Implementing Cisco IP Switched Networks Vendor : Cisco Version : DEMO Get Latest & Valid 642-813 Exam's Question

More information

Describing the STP. Enhancements to STP. Configuring PortFast. Describing PortFast. Configuring. Verifying

Describing the STP. Enhancements to STP. Configuring PortFast. Describing PortFast. Configuring. Verifying Enhancements to STP Describing the STP PortFast Per VLAN Spanning Tree+ (PVST+) Rapid Spanning Tree Protocol (RSTP) Multiple Spanning Tree Protocol (MSTP) MSTP is also known as Multi-Instance Spanning

More information

Question No: 1 On the MSTP network as shown in the figure, what is the role of the switch in MSTI 1 according to the configuration?

Question No: 1 On the MSTP network as shown in the figure, what is the role of the switch in MSTI 1 according to the configuration? Volume: 629 Questions Question No: 1 On the MSTP network as shown in the figure, what is the role of the switch in MSTI 1 according to the configuration? A. Root switch B. Slave switch C. Non-root switch

More information

Communication Redundancy User s Manual

Communication Redundancy User s Manual User s Manual Fifth Edition, June 2015 www.moxa.com/product 2015 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used

More information

MSTP Compatibility. Introduction. Topology. Autunm 2014

MSTP Compatibility. Introduction. Topology. Autunm 2014 MSTP Compatibility Autunm 2014 Topology Introduction As long as networks has been handled by hubs and switches according to the 802.1D standardization a magical protocol called Spanning-tree has been in

More information

Agenda. Spanning-Tree Protocol. Spanning Tree Protocol (STP) Introduction Details Convergence Some more details

Agenda. Spanning-Tree Protocol. Spanning Tree Protocol (STP) Introduction Details Convergence Some more details Agenda Spanning-Tree Protocol Spanning Tree Protocol (STP) Introduction Details Convergence Some more details Rapid Spanning Tree Protocol (RSTP) Cisco PVST, PVST+ Multiple Spanning Tree Protocol (MSTP)

More information

Configuring Optional STP Features

Configuring Optional STP Features CHAPTER 16 This chapter describes how to configure optional STP features. Note For complete syntax and usage information for the commands used in this chapter, refer to the Catalyst 6500 Series Switch

More information

2V] Chapter 2 Catalyst 3560 Switch Cisco IOS Commands shutdown. This command has no arguments or keywords.

2V] Chapter 2 Catalyst 3560 Switch Cisco IOS Commands shutdown. This command has no arguments or keywords. 2V] Chapter 2 Catalyst 3560 Switch Cisco IOS Commands shutdown shutdown Use the shutdown interface configuration command to disable an interface. Use the no form of this command to restart a disabled interface.

More information

Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Configuration Guide for Cisco 4000 Series ISR

Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Configuration Guide for Cisco 4000 Series ISR Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Configuration Guide for Cisco 4000 Series First Published: 2015-04-06 Last Modified: 2017-12-21 Cisco 4-Port and 8-Port Layer

More information

Configuring Spanning Tree Protocol

Configuring Spanning Tree Protocol CHAPTER 7 This chapter descibes how to configure Spanning Tree Protocol (STP) on the Cisco wireless mobile interface card (WMIC). Note For complete syntax and usage information for the commands used in

More information

CCNA Routing and Switching Study Guide Chapters 1 & 15: Enhanced Switching

CCNA Routing and Switching Study Guide Chapters 1 & 15: Enhanced Switching CCNA Routing and Switching Study Guide Chapters 1 & 15: Enhanced Switching Instructor & Todd Lammle Chapter 15 Objectives The ICND2 topics covered in this chapter include: 2 Chapter 15 Objectives (con

More information

Configuring Spanning Tree

Configuring Spanning Tree CHAPTER 8 Configuring Spanning Tree This chapter describes how to configure spanning tree on the Catalyst enterprise LAN switches. Note For information on configuring the PortFast, UplinkFast, and BackboneFast

More information

802.1w Rapid Spanning Tree Protocol (RSTP) 802.1d Spanning Tree Protocol (STP)

802.1w Rapid Spanning Tree Protocol (RSTP) 802.1d Spanning Tree Protocol (STP) 13 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1d Spanning Tree Protocol (STP) Contents Overview.................................................... 13-2 How Spanning Tree Operates.................................

More information

3. INTERCONNECTING NETWORKS WITH SWITCHES. THE SPANNING TREE PROTOCOL (STP)

3. INTERCONNECTING NETWORKS WITH SWITCHES. THE SPANNING TREE PROTOCOL (STP) 3. INTERCONNECTING NETWORKS WITH SWITCHES. THE SPANNING TREE PROTOCOL (STP) 3.1. STP Operation In an extended Ethernet network (a large network, including many switches) multipath propagation may exist

More information

Spanning Tree Protocol

Spanning Tree Protocol For conceptual information about, see the Using the with the EtherSwitch Network Module section of the EtherSwitch Network feature module. Finding Feature Information, page 1 Information About, page 1

More information

Configuring STP Extensions Using Cisco NX-OS

Configuring STP Extensions Using Cisco NX-OS This chapter describes how to configure Spanning Tree Protocol (STP) extensions on Cisco NX-OS devices. This chapter includes the following sections: Finding Feature Information, page 1 Information About

More information

Top-Down Network Design

Top-Down Network Design Top-Down Network Design Chapter Five Designing a Network Topology Original slides copyright by Cisco Press & Priscilla Oppenheimer Network Topology Design Issues Hierarchy Redundancy Modularity Well-defined

More information

STP (Spanning Tree Protocol) - Step by Step Configuration Tutorial

STP (Spanning Tree Protocol) - Step by Step Configuration Tutorial STP (Spanning Tree Protocol) - Step by Step Configuration Tutorial Introduction: Spanning Tree Protocol (STP) is a Layer 2 protocol that runs on switches. It was first introduced as CST (Common Spanning

More information

PrepKing. PrepKing

PrepKing. PrepKing PrepKing Number: 350-001 Passing Score: 800 Time Limit: 180 min File Version: 9.3 http://www.gratisexam.com/ PrepKing 350-001 Sections 1. Section 1.00 - Implement Layer 2 2. Section 2.00 - Implement IPv4

More information

Chapter 3 Lab 3-1, Spanning Tree Protocol (STP) Default Behavior

Chapter 3 Lab 3-1, Spanning Tree Protocol (STP) Default Behavior Chapter 3 Lab 3-1, Spanning Tree Protocol (STP) Default Behavior Topology Objective Background Observe the default behavior of STP. Four switches have just been installed. The distribution layer switches

More information

Chapter 5. Spanning Tree Protocol (STP) Part I

Chapter 5. Spanning Tree Protocol (STP) Part I Chapter 5 Spanning Tree Protocol (STP) Part I CCNA3-1 Chapter 5-1 Note for Instructors These presentations are the result of a collaboration among the instructors at St. Clair College in Windsor, Ontario.

More information

Chapter 4 Configuring Switching

Chapter 4 Configuring Switching Chapter 4 Configuring Switching Using the Switching Tab The navigation tabs on the top of the home page include a Switching tab that lets you manage your GS108T Gigabit Smart Switch using features under

More information

RSTP Configuration. RSTP Configuration

RSTP Configuration. RSTP Configuration RSTP Configuration Contents 16. STP Configuration...1 1.1 STP Overview...1 1.1.1 Function of STP... 1 1.1.2 Protocol Packets of STP... 1 1.1.3 Basic Concepts in STP... 1 1.1.4 Spanning-Tree Interface States...

More information

: Building Cisco Multilayer Switched Networks

: Building Cisco Multilayer Switched Networks Exam : Cisco 642-812 Title : Building Cisco Multilayer Switched Networks Version : Demo Cheat-Test,help you pass any IT exam! Q: 1 Which three statements about the Multiple Spanning Tree (MST) protocol

More information

CCNA Semester 3 labs. Labs for chapters 2 10

CCNA Semester 3 labs. Labs for chapters 2 10 CCNA Semester 3 labs Labs for chapters 2 10 2.1.4.5 Lab - Configure Extended VLANs, VTP, and DTP 2.2.2.5 Lab - Troubleshooting Inter-VLAN Routing 3.1.2.12 Lab - Building a Switched Network with Redundant

More information

CCNA Cisco Certified Network Associate CCNA (v3.0)

CCNA Cisco Certified Network Associate CCNA (v3.0) 200-125 - CCNA Cisco Certified Network Associate CCNA (v3.0) 1.What is one benefit of PVST+? A. PVST+ supports Layer 3 load balancing without loops. B. PVST+ reduces the CPU cycles for all the switches

More information

Routing Between VLANs Overview

Routing Between VLANs Overview Routing Between VLANs Overview This chapter provides an overview of VLANs. It describes the encapsulation protocols used for routing between VLANs and provides some basic information about designing VLANs.

More information

Implement Spanning Tree Protocols-PART-I. LAN Switching and Wireless Chapter 5 Modified by Tony Chen 05/01/2008

Implement Spanning Tree Protocols-PART-I. LAN Switching and Wireless Chapter 5 Modified by Tony Chen 05/01/2008 Implement Spanning Tree Protocols-PART-I LAN Switching and Wireless Chapter 5 Modified by Tony Chen 05/01/2008 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Notes: If you

More information