LA-140. Advanced ATM IAD FEATURES

Transcription

1 Advanced IAD FEATURES Offers voice, data and LAN to small and medium size businesses over single access line On the user side, supports up to 12 modular analog voice channels, 12 ISDN S0, E1/T1 port, a data port and a 10/100BaseT LAN port Offers ADSL, SDSL, SHDSL, or E1/T1 for WAN uplink Ensures reliable services and optimal utilization of the uplink using traffic shaping POTS and ISDN services over as per Loop Emulation Service (LES) standard, including Emulated Loop Control Protocol (ELCP) or CAS Inband or out-of-band (SNMP, Telnet) management and local management via ASCII terminal Comprehensive diagnostics and statistics on all ports Supported by RADview EMS, RAD s client-server, CORBA-based, secure and scaleable management solution

2 Advanced IAD DESCRIPTION is an Integrated Access Device (IAD) that enables service providers to offer transmission of voice, LAN and data to small and medium size businesses over a single access line. modules provide maximum flexibility for service integration, ease of use and scalability. They allow migration from E1/T1 to xdsl transmission mode without replacing the unit. A variety of ports are available: The user port can be a selectable, optional voice user port such as: 12 FXS, 12 ISDN S0, or E1/T1 An optional modular data port A fixed 10/100BaseT LAN port. performs circuit emulation using AAL1 to support voice interfaces. This facilitates the connection of s or other channeled E1/T1 devices. supports FXS and ISDN over AAL2 in accordance with the F LES standard for transport of different voice channels on the same Virtual Channel (VC). Traffic shaping per VC improves QoS and ensures better utilization of the uplink. supports IP routing and MAC bridging. It also supports Network Address Translation (NAT/PAT) and allows sharing of several IP addresses between various LAN users. supports DHCP, and allows sharing of IP address pools between DHCP clients on the LAN. For greater flexibility, supports different service types over : Ethernet and IP, in accordance with RFC The data ports support translation of IP traffic to Frame Relay over the network, in accordance with FRF.5, FRF.8, RFC 2427 and RFC As an IAD, provides QoS and management to ensure reliable services. Various management interfaces are available, including inband and out-of-band (SNMP) management, and local management via ASCII terminal. Comprehensive diagnostics and statistics on all ports and network layers enable network control and fault localization. The unit supports: Application layer statistics layer statistics and control (OAM support) Physical layer diagnostics (loopback tests, statistics). End-to-end QoS is measured using F5 OAM cells, including AIS, RDI, LB, CC and activation cells. is a compact, 1U-high unit, suitable as a desktop unit, can be wall-mounted, or placed in a 19-inch rack. APPLICATIONS IP Internet BAS V.35 E1 SHDSL DSLAM Public Network DSLAM SHDSL V.35 Router E1 Router LAN Figure 1. Leased Lines Application

3 SPECIFICATIONS UPLINK Layer Support AAL1 (CES and DB-CES), AAL2 and AAL5 QoS VC traffic shaping Services CBR, VBR, UBR OAM Cells Support F5 OAM cells as per I.610 E1 INTERFACE Type Network or user Payload Rate N x 64 kbps (N 25) ITU-T Rec. G.703, G.704, G.706, G.732, G.823 Framing 256N (no MF, CCS) 256N (no MF, CCS) with CRC-4 256S (TS16 MF, CAS) 256S (TS16 MF, CAS) with CRC-4 Line Rate Mbps ±32 PPM HDB3 Line Impedance 120Ω, balanced 75Ω, unbalanced Receive Level 0 to -30 db Transmit Level Balanced, ±3V ±10% Unbalanced, ±2.37V ±10% Jitter ITU-T G.823 Echo Cancellation In accordance with G.168 s Balanced, RJ-48C, 8-pin Unbalanced, two BNC SDSL UPLINK ETR-152 2B1Q RJ-48C 272, 400, 584, 768, 1168, 1552, 2320 kbps SHDSL UPLINK ITU-T G.992.1, Annex A, B or ETSI ETR PAM-16 RJ-45 N x 64 kbps, up to Mbps (2-wire) Handshake Protocol G Surge Protection ITU K.21 PSTN ISDN POTS V.5.2 SHDSL Voice Gateway Public Network DSLAM ADSL LAN IP BAS ISDN Internet LAN Figure 2. VoDSL Application

4 ADSL UPLINK ITU-T G Annex A, B Full DMT RJ-45 Up to 8 Mbps downstream, 1 Mbps upstream Surge Protection ITU K.21 T1 INTERFACE Applicable Standards AT&T TR-62411, ANSI T1.403 ITU G.703, G.704, G.706 Line Rate Mbps ±32 ppm B8ZS, B7ZS, AMI Line Impedance 100Ω, balanced Input Signal (Receive Level) Normal sensitivity: 0 to -36 db Low sensitivity: 0 to -30 db Output Signal (Transmit Level) ±3V ±10% CSU Emulation Software-adjustable attenuation of -7.5, -15, or db DSU Emulation Software-adjustable for ranges of 0 through 655 feet Framing ESF or SF, user-selectable Jitter ITU-T G.824 RJ-48C, 8-pin connector ANALOG VOICE Number of Ports Up to three 4-port modules, for a total of 12 channels, including an optional backup voice port for each module Modulation Method PCM (per ITU-T G.711 and AT&T PUB-43801), µ-law or A-Law Fax detection Nominal impedance: 600Ω Return loss: (ERL), better than 20 db Frequency Response (Ref: 1020 Hz) 0 ±0.5 db, 300 to 3000 Hz 0 ±1.1 db, 250 to 3400 Hz Signal to Total Distortion G.712, G.713 method 2: 0 to -30 dbm0: better than 33 db 3 to -45 dbm0: better than 22 db Idle Channel Noise Better than -70 dbm0 (+20 dbrnc) Transformer Isolation 1500 VRMS Echo Cancellation In accordance with G.168 FXS EIA RS-464 Loop start, WINK start (reverse polarity) for direct connection to a 2-wire telephone Advanced IAD DATA PORTS Number of Ports One modular data port supports Frame Relay over AAL5 or transparent over AAL1 N x 64 kbps 64, 128, 192, 256, 384, 448, 512, 576, 640, 704, 768, 832, 896, 960, 1024, 1088, 1152, 1216, 1280, 1344, 1408, 1472, 1536, 1600, 1664, 1728, 1792, 1856, 1920, 1984, 2048 kbps Interface and Connectors V.35: 34-pin, female (via adapter cable) RS-530: 25-pin D-type, female RS-449/V.36: 37-pin D-type female (via adapter cable) X.21: 15-pin D-type, female (via adapter cable) Clock Mode DCE ISDN INTERFACE Number of Ports Up to three 4-port modules, for a maximum of 12 S0 ports ETS , I.430, NTT, 5ESS, DMS-100, NI1 Bit Rate 192 kbps Line Coding Pseudo-ternary Line Termination 100 ±5% RJ-45

5 LAN INTERFACE Port 10/100BaseT Routing and Bridging Static, RIP I, II in compliance with IEEE DHCP Relay/Server NAT/PAT and Single IP PPPoE or PPPoA GENERAL Timing Modes Transmit timing from: Network derived Derived from E1 Adaptive clock NTR Management SNMP, Telnet and ILMI (statistics) Supervisory Ports Interface devices: DCE port: ASCII terminal Interface: V.24/RS-232, async Baud rate: kbps autobaud detection : RJ-45 Standards F: UNI 3.1, CES 2.0 (AF-VTOA-0078), DBCES (AF-VTOA-0085) LES VMOA 0145 ITU-T: I.361, I.362, I.363, I.364, I.365.1, I.413, I.555, I.610 RFC: RFC 2684, RFC 2427 Router RFC: RFC 2364, RFC 2131, RFC 2132, RFC 3022, RFC 1058 Indicators PWR (green) Lights up when power is ON RDY (green) Packets can be transferred LAN (green) Indicates transmission occurs for the LAN port WAN Indicates the operating status of the network port Green Synchronization occurs Red No synchronization Blinking Synchronization in process LINK1 DATA Lights up when a packet is received or transmitted from the user to the network side LINK2 DATA Lights up when a packet is received or transmitted from the user to the network side ALM (red) Lights up when alarm messages are stored in the alarm buffer LAN ERR Lights up when LAN interface indicates an error WAN ERR Lights up when WAN interface indicates an error LINK2 (of I/O1) ERR Lights up when the I/O1 interface indicates an error LINK1 (of I/O2) ERR Lights up when I/O2data interface indicates an error SYNC LOSS Lights up when the WAN/LINK1/LINK2 interfaces in the modules detect remote sync loss Advanced IAD Physical Height: 43.7 mm / 1.7 in Width: 432 mm / 17 in Depth: 243 mm / 9 in Weight: 2.3 kg / 5 lb Power 100 to 240 VAC (±10%) 10 to 15W, 47 to 63 Hz Environment Temperature: 0 50 C / F Humidity: Up to 90%, non-condensing

6 Advanced IAD ORDERING /$/* Modular IAD $ Specify power supply: AC for 100 to 240 VAC * Specify: EC for echo cancellation support /M/#/@ module # Specify interface type: ADSLA for ADSL Annex A ADSLB for ADSL Annex B SHDSL for SHDSL SDSL for SDSL 2B1Q E1 for E1 interface T1 for T1 interface ISDN/NT for four ISDN S0 NT ports module ISDN/TE for four ISDN S0 TE ports module FXS for four FXS ports module FXS/B for four FXS ports module with Specify serial data interface V35 for V.35 interface V36 for V.36 interface X21 for X.21 interface RS530 for RS-530 interface Note: To order a serial data interface, you must also specify an ADSLA, ADSLB, SHDSL, SDSL or E1 interface type. EC can be ordered only when using ISDN. VC includes EC. Data ports are SW selectable, and provided with an adapter cable to the specific connector type (V.35, X.21, etc.). For greater flexibility, the various cables can be ordered separately, to convert the data port to different connector types: CBL-530/V35/F for V.35 female connector CBL-HS2/X/1/F/J for X.21 female connector CBL-530/449/F for V.36 female connector data communications International Headquarters 24 Raoul Wallenberg Street Tel Aviv 69719, Israel Tel: (972) Fax: (972) , rad@rad.com U.S. Headquarters 900 Corporate Drive Mahwah, NJ Tel: (201) Toll free: Fax: (201) market@radusa.com / RAD Data Communications Ltd. Specifications are subject to change without prior notice. All other trademarks are the property of their respective holders.