CHIRON-4E1. E1 over Ethernet Multiplexer (TDM over IP)

Transcription

1 E1 over Ethernet Multiplexer (TDM over IP) Tranmission of up to 4x E1 PDH, G.703/704/723 E1 2048Mbit/s channels over Ethernet/IP network Built-in 5 port Gigabit Ethernet switch (4x 10/100/1000 Mbit/s RJ45 and 1x 1000Mbit/s SFP) Supports both point-to-point and point-to-multipoint applications, 4 independent E1 interfaces Configurable jitter buffer depth QoS (802.1p and Diffserv) and VLAN (802.1q, 802.1QinQ) support, egress and ingress rate limiting Local and remote software update, both firmware and GUI E1 physical layer alarms Local & remote loopback controls for diagnostics and troubleshooting SNMP, WWW, TELNET management CHIRON-4E1 multiplexer uses TDM over IP technology to transport four E1 2048kbit/s channels over Ethernet / IP network. Each E1 channel, along with it's framing and signaling bits, is encapsulated into IP packets with it's own IP address, VLAN ID, label and packet size. Device realise E1 to packet and packet to E1 conversion mechanism using the SAToP technology. Depending on configuration CHIRON-4E1 can work both as multiplexer in point-to-point applications or as concentrator in point-to-multipoint applications. Using CHIRON-4E1 multiplexer E1 data can be easily transported through the existing Ethernet or IP networks using any devices operating at layer 2 or layer 3 like switch, router, bridge or radio line. CHIRON-4E1 supports priority labeling ( according to IEEE 802.1p ) of encapsulated TDM traffic to ensure highest quality of transmission. An adaptive clock recovery mechanism provides reliable TDM clock recover, even under variable network conditions. Built-in Ethernet switch with four electrical 10/100/1000 Mbit/s ports and one 1000Mbit/s SFP port allow the User to create optical and copper E1 over IP connections with possibilty to assign each E1 port to specific Ethernet port. V4.06, page 1/5

2 Configurable jitter buffer compensates delay variation introduced by PSN network. Clear graphical network performance monitoring and diagnostic simplifies trouble-shooting and maintenance. Embedded HTTP server, TELNET server and SNMP agent allow free configuration of the device's performance by standard Web browser and continuous monitoring from any management platforms equipped with SNMP client. In addition, built-in SMTP service daemon allows to notify the operator in case of system failure. Device management is carried in band using any Ethernet port. Remote software update is supported to allow further functionality improving. Supported standards IEEE Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3u 100Base-FX Fast Ethernet Fiber IEEE 802.3ab 1000Base-T IEEE 802.3z Gigabit Fiber IEEE 802.3x Flow Control and Back-pressure IEEE 802.1p Class of Service (CoS) IEEE 802.1Q VLAN IEEE 802.1ad QinQ ITU-T G.703 ITU-T G.704 transparent channel ITU-T G.723 transparent channel V4.06, page 2/5

3 Supported protocols SNMP v1 NTP, SMTP, RMON, HTTP, Telnet, Syslog, MIB-II Supported standards, recommendations and directives EMC and safety*: EN 55011:2009+A1: Industrial, scientific and medical equipment Radio-frequency disturbance characteristics Limits and methods of measurement, EN 55024:2010+A1:2015 Information technology equipment. Immunity characteristics. Limits and methods, of measurement EN :2006+A2: Information technology equipment. Safety. General requirements, EMC 2004/108/WE Electromagnetic compatibility, LVD 2006/95/WE Low Voltage Directive, EN :2014 Safety of laser products. Equipment classification and requirements. IEC Electromagnetic compatibility (EMC)- Part 4-2: Testing and measurement techniques Electrostatic discharge immunity test, IEC Electromagnetic compatibility (EMC)- Part 4-3: Testing and measurement techniques Radiated, radio-frequency, electromagnetic field immunity test, IEC Electromagnetic compatibility (EMC) Part 4-4: Testing and measurement techniques Electrical fast transient/burst immunity test, IEC Electromagnetic compatibility (EMC) Part 4-5: Testing and measurement techniques Surge immunity test, IEC Electromagnetic compatibility (EMC) Part 4-6: Testing and measurement techniques Immunity to conducted disturbances, induced by radio-frequency fields, IEC Electromagnetic compatibility (EMC) Part 4-8: Testing and measurement techniques Power frequency magnetic field immunity test, IEC Electromagnetic compatibility (EMC) Part 4-11: Testing and measurement techniques Voltage dips, short interruptions and voltage variations immunity tests, IEC Electromagnetic compatibility (EMC) Part 4-12: Testing and measurement techniques Ring wave immunity test, IEC Electromagnetic compatibility (EMC) Part 4-29: Testing and measurement techniques Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests. *The scope and list of supported standards may vary with the development of the device E1 interfaces ITU-T G.703/704/723, 2048 kbit/s Loss of packages 1 % Maximum delay in each direction 100 ms, according to ITU-T G.114 Jitter - Change of delay 100 ms Ethernet interfaces 4x RJ45 10/100/1000 Mbps 1x SFP 1000 Mbps Flow-control autocrossover MDI, MDI-X Support VLAN, IEEE 802.1q MTU: do 9000 B Management HTTP protocol and web browser as a management application, telnet, SNMP SMTP - send an in the event of a failure BER 10-9 Impedance 120 Linear codehdb3 Clock restored from interface E1 or from Ethernet Connector RJ-45 In the band, through any Ethernet port, the ability to dedicate a dedicated management channel. Power supply DC, 6-60V VDC /1-0.15A AC, VDC / VAC / 90-40mA Two power inputs, redundant power supply - option for AC power supply Physical design Metal housing IP-30 Dimensions: 483x170x44 mm V4.06, page 3/5

4 Weight: 1.7 kg Standard operating temperature: 0 to +50 C Standard ambient humidity 0 to 95% (noncondensing) Location Type: Class C according to standard PN-EN sheltered locations view front / aside 19 view front view aside CHIRON-4E1-(x) Available Versions: None - standalone version 19 - device 1U 19 V4.06, page 4/5

5 Additional accessories: BTP-8524-S5CD 1.25G, 850nm, MM, 550m, SFP, LC, 0~70 O C BTP-3124-L2CD 1.25G, 1310nm, MM/SM, 2/20km, SFP, LC, 0~70 O C BTP-3124-L4CD 1.25G, 1310nm, SM, 40km, SFP, LC, 0~70 O C BTP-5524-L4CD 1.25G, 1550nm, SM, 40km, SFP, LC, 0~70 O C BTP-5524-L8CD 1.25G, 1550nm, SM, 80km, SFP, LC, 0~70 O C BTP CD 1.25G, 1550nm, SM, 120km, SFP, LC, 0~70 O C BTPB-3524L-L2CD 1.25G, 1310/1550nm, SM, 20km, SFP, WDM, LC, 0~70 O C BTPB-5324L-L2CD 1.25G, 1550/1310nm, SM, 20km, SFP, WDM, LC, 0~70 O C BTPB-3524S-L2CD 1.25G, 1310/1550nm, SM, 20km, SFP, WDM, SC, 0~70 O C BTPB-5324S-L2CD 1.25G, 1550/1310nm, SM, 20km, SFP, WDM, SC, 0~70 O C BTPB-3524L-L4CD 1.25G, 1310/1550nm, SM, 40km, SFP, WDM, LC, 0~70 O C BTPB-5324L-L4CD 1.25G, 1550/1310nm, SM, 40km, SFP, WDM, LC, 0~70 O C BTPB-3524S-L4CD 1.25G, 1310/1550nm, SM, 40km, SFP, WDM, SC, 0~70 O C, BTPB-5324S-L4CD 1.25G, 1550/1310nm, SM, 40km, SFP, WDM, SC, 0~70 O C BTE-GB-P1RC 10/100/1000M, 100m(UTP-5), Copper SFP, RJ-45, 0~70 O C BTE-GB-P3RC 1000M, 100m(UTP-5), Copper SFP, RJ-45, 0~70 O C ZAS-ANYMUX-01 Power Supply 230V AC(DC) / 48V DC 0.5A, 30W, adapter ZAS-ANYMUX-02 Power Supply 230V AC(DC) / 48V DC 0.5A, 25W, desktop LT "rack mount for 4x Chiron-4E1 V4.06, page 5/5