QUICK START GUIDE. Wi-Fi Router with

Transcription

1 QUICK START GUIDE Wi-Fi Router with

2 What s in the Box A 2

3 QUICK START GUIDE C Wi-Fi Router with B D A: SBR-AC3200P Wi-Fi Router B: Power Cable C: Ethernet Cable D: Quick Start Guide 3

4 Front Panel Primary LED 4

5 Rear Panel LED Status Indicators 5

6 The SBR-AC3200P is more than just a Wi-Fi Router. It is the start of a new home network experience. You can set it up as a stand-alone Router. And with the optional RipCurrent Extenders, you can set up a high-speed whole-home Wi-Fi network that uses your existing AC electrical wiring and outlets. For Internet connections, you must have a cable, DSL, or satellite Internet Service Provider (ISP) service connection to the Internet. For a video guide to setting up your Router, visit youtu.be/arfv2auypli. 6

7 Introduction Set Up Your Router 8 1 Add RipCurrent Wired or Wi-Fi Extenders 14 2 Personalize Your Network 22 3 Connect Devices to Your Wi-Fi Network 28 4 Troubleshooting

8 1 Set Up Your Router 8

9 9

10 A Reset your Internet modem by unplugging its power supply, waiting 30 seconds, and then plugging it back in. It will take a few moments for it to re-register with your service provider. 10

11 B Connect the SBR-AC3200P to an electrical outlet. The front LED will flash green. 11

12 C Connect the included Ethernet cable between the blue WAN port on the Router and an Ethernet port on your Internet modem. The front LED will turn solid green, indicating that the Router has connected to the Internet. This may take 2-3 minutes to complete. 12

13 D After the Wi-Fi LED on the back panel turns green, verify Router connectivity by accessing the Internet. Connect to the Router with a PC or other device using the SSID and passcode found on the bottom of the Router. You can also connect with an Ethernet cable (not provided). 13

14 2 Add Wired or Wi-Fi Extenders (sold separately) 14

15 15

16 A Plug in your RipCurrent Extender, into an AC outlet close to the SBR-AC3200P Router. If you have more than one Extender to install, finish installing one before you move on to the next one. SBX-AC1200P Wi-Fi Extender SBX-1000P Wired Extender 16

17 The RipCurrent network will connect automatically in a non-encrypted mode, indicated by a red status LED (located on the back of your Router or the side of your Extender). This may take 2-3 minutes to complete. 17

18 B Relocate the Extender to the room where you want to extend your network. Use the SBX-AC1200P Wi-Fi Extender anywhere you need to improve the Wi-Fi signal. The LAN port can be used to connect an Ethernet device such as a TV or gaming console to the network. 18

19 Use the SBX-1000P Wired Extender anywhere you need to connect an Ethernet device such as a TV or gaming console to the network. 19

20 C Check your RipCurrent signal strength. Rear panel LEDs on the Router and on the side of RipCurrent Extenders will indicate the signal strength. Red = Fair signal Amber = Good signal Green = Excellent signal 20

21 If the LED is red or amber, consider adjusting the location to find a better signal. Once you re satisfied with the connection quality, you can begin installing the next Extender, if you have more than one to install. 21

22 3 Personalize Your Network 22

23 23

24 A Manage your SBR-AC3200P by opening a browser (such as Internet Explorer, Chrome, etc.) and access The default credentials are case sensitive. Log in: admin Password: password 24

25 B Change your Web Manager password, found under the Status Tab Security settings. 25

26 C Change your SSID name and passphrase, found under the Primary Network Settings. 26

27 To encrypt your RipCurrent network and adjust other advanced Router settings, see the SBR-AC3200P User Guide at the ARRIS Support website, 27

28 4 Connect Devices to Your Wi-Fi Network 28

29 29

30 A On the device that you want to connect to your network, open the software utility that manages your Wi-Fi connections. 30

31 B Select the Wi Fi network that you set up when you personalized your Wi-Fi network. Enter the password that you set up when you personalized your network. The device should connect to your Wi-Fi network. 31

32 5 Troubleshooting 32

33 33

34 34 No Internet Connection

35 Check the status of your Internet modem and the connecting Ethernet cable. 35

36 36 No Wireless Connectivity

37 Is the LED status indicator on the front panel amber? If so, press the standby button to activate wireless capabilities. Access the Web Manager for more information on your wireless network. 37

38 38

39 2017 ARRIS Enterprises LLC. All Rights Reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS Enterprises LLC. ( ARRIS ). ARRIS reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of ARRIS to provide notification of such revision or change. ARRIS and the ARRIS logo are all trademarks of ARRIS Enterprises LLC. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks or the names of their products. ARRIS disclaims proprietary interest in the marks and names of others. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google Play and the Google Play logo are trademarks of Google Inc. 39

40 For additional assistance with your SURFboard Router, ARRIS is here to help. Visit for self help, FAQs, product manuals, and live chat with support staff. Send us an via our consumer web site or give a call to ARSVD01750-B 10/17