BR411AP n Wireless Access Point and Bridge

Transcription

1 BR411AP n Wireless Access Point and Bridge

2 The BR411AP provides connectivity between Ethernet wired networks and radio-equipped wireless devices. It is an easy, web-based setup for installation and management. Even though you may not be familiar with the AP, this guide will make configuring the AP easy. Before installing the AP, please look through this guide to get to know all the AP s functions. Features: Supports 64/128-bit WEP, complies with 128 bit WPA standard(tkip/aes) Supports 135/121.5/108/81/54/40.5/27/13.5/65/58.5/52/39/26/19.5/13/6.5/54/48/ 36/24/18/12/9/6/11/5.5/2/1Mbps wireless LAN data transfer rates Provides Bridge(AP/Client) mode Wireless speed up to 150Mbps when connected to 11n device Wireless security encryption easily at a push of WPS button Seamlessly compatible with b and g devices 2dBi Fixed Antenna Specifications: Software Specification Standards IEEE n, IEEE g, IEEE b Wireless Signal Rates 11n: Up to 150Mbps (Dynamic) With Automatic Fallback 11g: Up to 54Mbps (Dynamic) 11b: Up to 11Mbps (Dynamic) Frequency Range GHz Wireless Transmit Power 20dBm(MAX) Modulation Type DBPSK,DQPSK,CCK, OFDM 135M: -68dBm@10% PER Receiver Sensitivity 54M: -68dBm@10% PER 11M: -85dBm@8% PER Wireless Range Indoors up to 100m, Outdoors up to 300m Wireless Security 64/128 bit WEP WPA/WPA2, WPA-PSK/WPA2-PSK (TKIP/AES) Hardware Specification Interface 1 10/100M Ethernet Ports Antenna Type Detachable Omni-directional Antenna Power supply Input AC100~240V,output DC9 V/1A Operating Temperature0 C~40 C (32~104) Storage Temperature -40 C~70 C (-40~158) Relative Humidity 10% ~ 90%, non condensation Storage Humidity 5%~95% non-condensing Weight 110.6g Dimensions 88mm 88mm 30 mm

3 1. Hardware installation: 1-1 Connect one end of power adapter to power port on Wireless Access Point and connect the other end into an available electrical outlet. 1-2 Connect Ethernet cable between computer and Access Point s Ethernet port when you want to set the Access Point. After finishing settings, connect the Ethernet cable between the wired network(router or Switch) and the Access Point s Ethernet port. 2. Software installation: 2-1 IP address assignment You must assign your computer a static IP address within the same range as the IP address of the Access Point. The Access Point s default IP address is with a Subnet mask of Please see the detailed information below: Windows 2000/XP IP address assignment Click the Start button (it should be located at the lower-left corner of your monitor), then click Control Panel. Double-click Network Connections, then right-click Local Area Connection, Select Properties, Local Area Connection status window will appear. Select Internet Protocol(TCP/IP), Click Properties,

4 In the IP address field, enter the address x (x should be replaced by a number between 2 and 253, such as 101). In the Subnet mask field, enter Windows Vista IP address assignment Click the Start button (it should be located at the lower-left corner of your monitor), then click Control Panel. Click View network status and tasks (under Network and Internet).

5 Click Manage network connections Right-click Local Area Connection, Select Properties, Local Area Connection status window will appear.

6 Select Internet Protocol Version 4 (TCP/IPv4), Click Properties, In the IP address field, enter the address x (x should be replaced by a number between 2 and 253, such as 101). In the Subnet mask field, enter NOTE: If numbers are already present in the IP address, Subnet Mask and/or Default gateway fields, be sure to write them down as you will need to re-enter them so your PC can access the Internet once Access Point configuration is complete.

7 2-2 Access Point Configuration Login Typing in the address field of web browser. After a moment, a login window will appear, Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key. After your successful login, you can configure and manage the AP LAN Settings You may enable/disable networking functions and configure their parameters as your wish. for example, you can change the IP address and enable/disable the DHCP server, if there exist another DHCP server within your network, you must disable this AP s DHCP server. As below: Click Internet Settings LAN Click Apply save the settings Wireless Settings Basic Wireless Settings You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Channel. The Access Point can be set simply with only the minimum setting items. As below: Click Wireless Settings Basic

8 Wireless Security/Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring. As below: Click Wireless Settings Security Click Apply save settings Wi-Fi Protected Setup You could setup security easily by choosing PIN or PBC method to do Wi-Fi Protected Setup. As below: Click Wireless Setting WPS

9 Click Apply save settings Finish above settings, you can connect this AP to your wired network(router or switch) and setup your pc s wireless LAN adapter and select the AP s SSID to join it. Then you can communicate wirelessly with other client within wired network.