MAC Address Configuration Commands
|
|
|
- Marilyn Pierce
- 5 years ago
- Views:
Transcription
1
2 Table of Contents Table of Contents Chapter mac address-table static mac address-table aging-time show mac address-table clear mac address-table I -
3 Chapter 1 MAC Address Configuration Commands mac address-table static [no] mac address-table static mac-addr vlan vlan-id interface interface-id To add a static MAC address, run mac address-table static mac-addr vlan vlan-id interface interface-id. To cancel the static MAC address, run no mac address-table static mac-addr vlan vlan-id interface interface-id. mac-addr Means an MAC address. Value range: H.H.H vlan-id A VLAN that the MAC address belongs to Value range: interface-id Physical port that the MAC address belongs to N/A Explanation This command is configured in global configuration mode. The following example shows how to bind MAC address ab to port G0/2 of VLAN1. Switch_config# mac address-table static ab vlan 1 interface g0/ mac address-table aging-time mac address-table aging-time [ ] - 1 -
4 To configure the aging time of the MAC address table, run the previous command. 0 Means that the MAC address never ages Aging time of the MAC address whose unit is second 300s. Explanation This command is configured in global configuration mode. The following example shows how to set the aging time of the MAC address to 100 seconds. Switch_config# mac address-table aging-time show mac address-table show mac address-table [dynamic [interface interface-id vlan vlan-id] static brief multicast interface interface-id vlan vlan-id H.H.H] To display the MAC address table of the switch, run show mac address-table {dynamic [interface interface-id vlan vlan-id] static brief multicast interface interface-id vlan vlan-id H.H.H]. dynamic interface-id Dynamically-learned MAC address table Name of an interface vlan-id VLAN ID Value range: static brief multicast Interface Vlan Static MAC address table Brief information about the MAC address Multicast MAC address table Port s MAC address table Vlan mac address table - 2 -
5 H.H.H Specific address N/A Explanation This command is used to display the MAC address table. The following example shows how to display all dynamic MAC address tables. Switch_config#show mac address-table Mac Address Table (Total 2) Vlan Mac Address Type Ports a7c.fad3 DYNAMIC g0/ DYNAMIC g0/ clear mac address-table clear mac address-table dynamic vlan vlan-id] [address mac-addr interface interface-id To delete a dynamic MAC address, run the above-mentioned command: address mac-addr interface-id Means an MAC address. Value range: H.H.H Means a name of a L2 interface. vlan-id VLAN ID Value range: N/A - 3 -
6 Remarks This command is used in EXEC mode. The following example shows how to clear all dynamically learned MAC addresses on interface g0/2. Switch# clear mac address-table dynamic interface g0/2-4 -
Web Configuration Commands
Web Configuration Commands Table of Contents Table of Contents Chapter 1 STP Configuration Commands...1 1.1 ip http language...1 1.2 ip http port...1 1.3 ip http secure-port...2 1.4 ip http server...2
Basic Port Configuration
Basic Port Configuration Page 1 of 8 Contents Contents...2 Chapter 1 Port Security... 3 1.1 Port Security Description...3 1.1 Port Security Configuration...4 1.2 Configuration example...5 Page 2 of 8 Chapter
MAC Learning Command Reference
MAC Learning Reference This chapter describes commands to configure MAC learning. clear mac-address-table, page 2, page 3 mac limit maximum addresses, page 5 mac static address, page 6 show mac-address-table,
This chapter describes MAC learning, MAC address limiting, and static MAC address. This chapter also describes the configuration procedures.
This chapter describes MAC learning, MAC address limiting, and static MAC address. This chapter also describes the configuration procedures. Understanding, page 1 Understanding MAC Address Limiting, page
Command Manual MAC Address Table Management H3C S5500-EI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 MAC Address Table Management... 1-1 1.1.1 display mac-address... 1-1 1.1.2 display mac-address aging-time... 1-2 1.1.3 mac-address (Ethernet port view)...
Configuring MAC Address Tables
This chapter contains the following sections: Information About MAC Addresses, page 1 Configuring MAC Addresses, page 2 Configuring MAC Move Loop Detection, page 4 Verifying the MAC Address Configuration,
IGMP Snooping Configuration
IGMP Snooping Configuration Page 1 of 14 Contents Chapter 1 IGMP Snooping...3 1.1 Brief Introduction to IGMP Snooping... 3 1.2 IGMP Snooping Configuration... 3 1.2.1 Brief Configuration to IGMP Snooping...
Cisco IOS Commands. abort CHAPTER
CHAPTER 2 abort Use the abort VLAN database command to abandon the proposed new VLAN database, exit VLAN database mode, and return to privileged EXEC mode. abort This command has no arguments or keywords.
Configuring DHCP Features
CHAPTER 19 This chapter describes how to configure Dynamic Host Configuration Protocol (DHCP) snooping and the option-82 data insertion features on the Catalyst 3750 switch. Unless otherwise noted, the
Configuring Protocol VLAN
CHAPTERS 1. Overview 2. Protocol VLAN Configuration 3. 4. Appendix: Default Parameters Overview This guide applies to: T1500G-10PS v2 or above, T1500G-8T v2 or above, T1500G-10MPS v2 or above, T1500-28PCT
Link Aggregation Configuration Commands
Link Aggregation Configuration Commands Table of Contents Table of Contents Chapter 1...1 1.1...1 1.1.1 aggregator-group...1 1.1.2 aggregator-group load-balance...2 1.1.3 show aggregator-port...3 1.1.4
Configuring Port-Based Traffic Control
CHAPTER 18 This chapter describes how to configure port-based traffic control features on the Catalyst 3750 Metro switch. For complete syntax and usage information for the commands used in this chapter,
Configuring MAC Address Tables
This chapter contains the following sections: Information About MAC Addresses, page 1 Configuring MAC Addresses, page 1 Verifying the MAC Address Configuration, page 4 Information About MAC Addresses To
ACL Configuration FSOS
FSOS ACL Configuration 1 Contents 1. ACL Configuring...3 1.1 Brief Introduction to ACL... 3 1.1.1 Configuring Match Order... 3 1.1.2 Switch Support ACL... 4 1.2 Configuring Time Range...4 1.2.1 Configuration
Configuring Command Macros
CHAPTER 10 This chapter describes how to configure and apply command macros on the Cisco ME 3400 switch. Note For complete syntax and usage information for the commands used in this chapter, see the command
Configuring MAC Address Tables
This chapter contains the following sections: Information About MAC Addresses, page 1 Guidelines for Configuring the MAC Address Tables, page 2 MAC Address Movement, page 2 Configuring MAC Addresses, page
Cisco IOS Commands. abort CHAPTER
CHAPTER 2 abort Use the abort VLAN database command to abandon the proposed new VLAN database, exit VLAN database mode, and return to privileged EXEC mode. abort This command has no arguments or keywords.
MAC Address Management
D MAC Address Management Contents Overview.................................................... D-2.................................. D-3 Menu: Viewing the Switch s MAC Addresses.................... D-4
Configuring EtherChannels
27 CHAPTER This chapter describes how to configure EtherChannel on Layer 2 interfaces. EtherChannel provides fault-tolerant high-speed links between switches, routers, and servers. You can use it to increase
Configuring Smartports Macros
CHAPTER 11 This chapter describes how to configure and apply Smartports macros on the Catalyst 2960 switch. Note For complete syntax and usage information for the commands used in this chapter, see the
Configuring Multicast VLAN Registration
Finding Feature Information, page 1 Restrictions for MVR, page 1 Information About Multicast VLAN Registration, page 2 How to Configure MVR, page 5 Monitoring MVR, page 10 Configuration Examples for MVR,
FiberstoreOS. VPN Command Line Reference
FiberstoreOS VPN Command Line Reference Contents 1 VRF Commands...3 1.1 ip vrf...3 1.2 show ip vrf...3 1.3 ip vrf forwarding...4 1.4 ip route vrf...5 1.5 arp vrf... 5 1.6 show ip arp vrf... 6 1.7 clear
Configuring BPDU tunneling
Contents Configuring BPDU tunneling 1 Introduction to BPDU tunneling 1 Background 1 BPDU Tunneling implementation 2 Configuring BPDU tunneling 3 Configuration prerequisites 3 Enabling BPDU tunneling for
Configuring Layer 2 Switching
This chapter describes how to configure Layer 2 switching using Cisco NX-OS. This chapter includes the following sections: Finding Feature Information, page 1 Information About Layer 2 Switching, page
FiberstoreOS. VPN Command Line Reference
FiberstoreOS VPN Command Line Reference Contents 1 VRF Commands...1 1.1 ip vrf...1 1.2 show ip vrf...1 1.3 ip vrf forwarding...2 1.4 ip route vrf...3 1.5 arp vrf... 3 1.6 show ip arp vrf...4 1.7 clear
Configuring Layer 2 Switching
Configuring Layer 2 Switching This chapter describes how to configure Layer 2 switching using Cisco NX-OS. This chapter includes the following sections: Information About Layer 2 Switching, page 1 Licensing
Configuring MAC Address Tables
This chapter contains the following sections: Information About MAC Addresses, page 1 Configuring MAC Addresses, page 2 Verifying the MAC Address Configuration, page 4 Verifying RMAC Learning Feature,
Configuring Ethernet CFM and E-LMI
36 CHAPTER Metro Ethernet service providers in particular require certain management capability within the context of the overall Ethernet infrastructure (EI). Ethernet operation, administration, and maintenance
Configuring SDM Templates
CHAPTER 8 This chapter describes how to configure the Switch Database Management (SDM) templates on the Catalyst 3750 switch. Unless otherwise noted, the term switch refers to a standalone switch and a
Syslog Function Configuration
Syslog Function Configuration Page 1 of 11 Contents Contents... 2 Chapter 1 Syslog Function Configuration...3 1.1 Syslog Introduction...3 1.1 Syslog Function Configuration...3 1.1.1 Syslog Function Configuration
Configuring VLAN-VPN CHAPTERS
CHAPTERS 1. VLAN-VPN 2. Basic VLAN-VPN Configuration 3. Flexible VLAN-VPN Configuration 4. Configuration Example 5. Appendix: Default Parameters VLAN-VPN This guide applies to: T2600G-28TS v3 or above,
FSOS VPN Command Line Reference
FSOS VPN Command Line Reference Contents 1 VRF Commands...3 1.1 ip vrf...3 1.2 show ip vrf... 4 1.3 ip vrf forwarding... 5 1.4 ip route vrf...6 1.5 arp vrf...7 1.6 show ip arp vrf... 9 1.7 clear ip arp
VxLAN and HW-VTEP configuration example
VxLAN and HW-VTEP configuration example VxLAN and HW-VTEP configuration example Table of Contents 1. VxLAN configuration... 1 1.1. Configuration example... 2 1.1.1. Configure VTEP 1:... 2 1.1.2. Configure
IPv6 Configuration Commands
IPv6 Configuration Commands Table of Contents Table of Contents Chapter 1 IPv6 Configuration Commands...1 1.1 IPv6 Configuration Commands...1 1.1.1 ipv6 address...1 1.1.2 ipv6 address anycast...2 1.1.3
Configuring Access Point Groups
Finding Feature Information, page 1 Prerequisites for Configuring AP Groups, page 1 Restrictions for, page 2 Information About Access Point Groups, page 2 How to Configure Access Point Groups, page 4 Additional
Configuring SDM Templates
CHAPTER 8 This chapter describes how to configure the Switch Database Management (SDM) templates on the Catalyst 3750 switch. Unless otherwise noted, the term switch refers to a standalone switch and a
FiberstoreOS IP Service Configuration Guide
FiberstoreOS IP Service Configuration Guide Contents 1 Configuring ARP...4 1.1 Overview...4 1.2 Configuring ARP... 4 1.3 Validation commands...5 2 Configuring Proxy ARP... 7 2.1 Overview...7 2.2 Configuring
Configuring SmartPort Macros
CHAPTER 10 This chapter describes how to configure and apply SmartPort macros on your switch. Note For complete syntax and usage information for the switch commands used in this chapter, look at the Cisco
Configuring Layer 3 Interfaces
This chapter contains the following sections: Information About Layer 3 Interfaces, page 1 Licensing Requirements for Layer 3 Interfaces, page 4 Guidelines and Limitations for Layer 3 Interfaces, page
Recommendations for Upgrading a Catalyst 2950 Switch to a Catalyst 2960 Switch
APPENDIXC Recommendations for Upgrading a Catalyst 2950 Switch to a Catalyst 2960 Switch This appendix describes the configuration compatibility issues and the feature behavior differences that you might
Configuring SDM Templates
CHAPTER 8 The Catalyst 3750 switch command reference has command syntax and usage information. Unless otherwise noted, the term switch refers to a standalone switch and a switch stack. Understanding the
Radius Configuration FSOS
FSOS Radius Configuration Contents 1. RADIUS Configuration... 1 1.1 Radius Overview...1 1.1.1 AAA Overview...1 1.1.2 AAA Realization...1 1.1.3 RADIUS Overview...2 1.2 RADIUS Configuration... 3 1.2.1 RADIUS
Configuring PTP. Information About PTP. This chapter contains the following sections:
This chapter contains the following sections: Information About PTP Information About PTP, on page 1 PTP Device Types, on page 2 PTP Process, on page 3 High Availability for PTP, on page 3 Licensing Requirements
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 9 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094). It includes information about VLAN membership modes, VLAN configuration
Configuring Access and Trunk Interfaces
Configuring Access and Trunk Interfaces Ethernet interfaces can be configured either as access ports or trunk ports. Trunks carry the traffic of multiple VLANs over a single link and allow you to extend
Attack Protection. FSOS Attack Protection Configuration
FSOS Attack Protection Configuration Contents 2. Attack Protection... 1 1.1 Anti-DDOS Attack Function... 1 1.1.1 Anti-TTL Attack... 1 1.1.2 Configure Anti-IP Fragment Attack...1 1.1.3 Configuration Example...
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 14 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094). It includes information about VLAN modes and the VLAN Membership
Configuring Port-Based Traffic Control
CHAPTER 22 This chapter describes how to configure the port-based traffic control features on the Cisco ME 3400 Ethernet Access switch. For complete syntax and usage information for the commands used in
Configuring 802.1x CHAPTERS. 1. Overview x Configuration 3. Configuration Example 4. Appendix: Default Parameters
CHAPTERS 1. Overview 2. 3. Configuration Example 4. Appendix: Default Parameters Overview This guide applies to: T1500G-10PS v2 or above, T1500G-8T v2 or above, T1500G-10MPS v2 or above, T1500-28PCT v3
Configuring HSRP. Understanding HSRP CHAPTER
CHAPTER 40 This chapter describes how to use Hot Standby Router Protocol (HSRP) on the Cisco ME 3400E Ethernet Access switch to provide routing redundancy for routing IP traffic without being dependent
Configuring MLD Snooping
This module contains details of configuring MLD snooping Finding Feature Information, page 1 Information About Configuring IPv6 MLD Snooping, page 1 How to Configure IPv6 MLD Snooping, page 6 Displaying
Lab Viewing Network Device MAC Addresses
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.1 255.255.255.0 N/A PC-A NIC 192.168.1.3 255.255.255.0 192.168.1.1 Part 1: Configure Devices
Command Manual Network Protocol. Table of Contents
Table of Contents Table of Contents Chapter 1 IP Address Configuration Commands... 1-1 1.1 IP Address Configuration Commands... 1-1 1.1.1 display ip host... 1-1 1.1.2 display ip interface... 1-1 1.1.3
Shutdown-Control FSOS. Shutdown-Control Configuration
FSOS Shutdown-Control Configuration Contents 1. Shutdown-Control...1 1.1 Overview... 1 1.1.1 Enable/disable Shutdown-Control... 1 1.1.2 Configure Recovery Mode...1 1.1.3 Manually Restore Shutdown Port...
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 10 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the switch. It includes information about VLAN membership
Converged Access: Enabling Wireless
This chapter describes how to deploy a converged access switch, connect it as a mobility member in your converged topology, activate access point licenses, and have the access points ready for physical
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 11 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on your Catalyst 3550 switch. It includes information about VLAN
Configuring SDM Templates
CHAPTER 8 This chapter describes how to configure the Switch Database Management (SDM) templates on the Catalyst 3750 switch. Unless otherwise noted, the term switch refers to a standalone switch and a
Configuring Port-Based Traffic Control
CHAPTER 17 This chapter describes how to configure the port-based traffic control features on your switch. For complete syntax and usage information for the commands used in this chapter, refer to the
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide. Figure 9-1 Port Security Global Settings window
9. Security DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Security 802.1X AAA RADIUS TACACS IMPB DHCP Server Screening ARP Spoofing Prevention MAC Authentication Web-based
IEEE 802.1X Multiple Authentication
The feature provides a means of authenticating multiple hosts on a single port. With both 802.1X and non-802.1x devices, multiple hosts can be authenticated using different methods. Each host is individually
Using the Command-Line Interface
CHAPTER 1 The Catalyst 3750 switch is supported by Cisco IOS software. This chapter describes how to use the switch command-line interface (CLI) to configure software features. For a complete description
Configuring NTP. Information About NTP. Information About the NTP Server. This chapter contains the following sections:
This chapter contains the following sections: Information About NTP Information About NTP, on page 1 Licensing Requirements, on page 3 Prerequisites for NTP, on page 3 Guidelines and Limitations for NTP,
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 16 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on your Catalyst 2950 or Catalyst 2955 switch. It includes information
Configuring PIM snooping
Contents Configuring snooping 1 snooping overview 1 Configuring snooping 2 Displaying and maintaining snooping 2 snooping configuration example 3 Troubleshooting snooping 6 snooping does not work 6 Some
FSOS. Ethernet Configuration Guide
FSOS Ethernet Configuration Guide Contents 1 Configuring Interface... 1 1.1 Overview...1 1.2 Configuring Interface State...1 1.2.1 Configurations...1 1.2.2 Validation...1 1.3 Configuring Interface Speed...
Configuring LLDP and LLDP-MED
CHAPTER 26 Note This chapter describes how to configure the Link Layer Discovery Protocol (LLDP) and LLDP Media Endpoint Discovery (LLDP-MED) on the Catalyst 3560 switch.for complete syntax and usage information
Configuring SPAN and RSPAN
34 CHAPTER This chapter describes how to configure the Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) on the Catalyst 4500 series switches. SPAN selects network traffic for analysis by a network
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 12 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the switch. It includes information about VLAN membership
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 14 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Catalyst 3750 switch. It includes information about VLAN
Configuring DLDP CHAPTERS. 1. Overview 2. DLDP Configuration 3. Appendix: Default Parameters
CHAPTERS 1. Overview 2. 3. Appendix: Default Parameters Overview This guide applies to: T1500G-10PS v2 or above, T1500G-8T v2 or above, T1500G-10MPS v2 or above, T1500-28PCT v3 or above, T1600G-52TS v3
Configuring LLDP and LLDP-MED
CHAPTER 24 This chapter describes how to configure the Link Layer Discovery Protocol (LLDP) and LLDP Media Endpoint Discovery (LLDP-MED) on the Cisco ME 3400 switch. Note For complete syntax and usage
Loop detection commands 1
Contents Loop detection commands 1 display loopback-detection 1 loopback-detection action 1 loopback-detection enable 2 loopback-detection global action 3 loopback-detection global enable 4 loopback-detection
Using the Command-Line Interface
CHAPTER 1 The Cisco Metro Ethernet (ME) 3400E Series Ethernet Access switch is supported by Cisco IOS software. This chapter describes how to use the switch command-line interface (CLI) to configure software
Configuring SDM Templates
Finding Feature Information, page 1 Information About, page 1 How to Configure SDM Templates, page 4 Configuration Examples for SDM Templates, page 5 Additional References for SDM Templates, page 7 Feature
Configuring EtherChannels and Layer 2 Trunk Failover
28 CHAPTER Configuring EtherChannels and Layer 2 Trunk Failover This chapter describes how to configure EtherChannels on Layer 2 ports on the switch. EtherChannel provides fault-tolerant high-speed links
Configuring the MAC Address-Table Move Update Feature
Configuring the MAC Address-Table Move Update Feature Finding Feature Information, page 1 Information About MAC Address-Table Move Update, page 1 How to Configure MAC Address-Table Move Update, page 3
Operation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
Configuring the MAC Address Table
CHAPTER 2 For information about creating interfaces, see the document, Cisco Nexus 1000V Interface Configuration Guide, Release 4.0(4)SV1(3). This chapter includes the following topics: Information About
Configuring Dynamic VLAN Membership
CHAPTER 11 This chapter describes how to configure dynamic port VLAN membership by using the VLAN Membership Policy Server (VMPS). This chapter includes the following major sections: Understanding VMPS,
Configuring EtherChannels and Link-State Tracking
30 CHAPTER Configuring EtherChannels and Link-State Tracking This chapter describes how to configure EtherChannels on Layer 2 ports on the Catalyst 2960 switch. EtherChannel provides fault-tolerant high-speed
Data Center Configuration. 1. Configuring VXLAN
Data Center Configuration 1. 1 1.1 Overview Virtual Extensible Local Area Network (VXLAN) is a virtual Ethernet based on the physical IP (overlay) network. It is a technology that encapsulates layer 2
26 CHAPTER Virtual Private Networks (VPNs) provide a secure way for customers to share bandwidth over an ISP backbone network. A VPN is a collection of sites sharing a common routing table. A customer
Configuring VLANs. Understanding VLANs CHAPTER
CHAPTER 11 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Cisco ME 3400 Ethernet Access switch. It includes information
Configuring Layer 3 Interfaces
This chapter contains the following sections: Information About Layer 3 Interfaces, page 1 Licensing Requirements for Layer 3 Interfaces, page 4 Guidelines and Limitations for Layer 3 Interfaces, page
Using the Command-Line Interface
CHAPTER 1 The Cisco IE 3000 switch is supported by Cisco IOS software. This chapter describes how to use the switch command-line interface (CLI) to configure software features. For a complete description
Web and MAC Authentication
3 Web and MAC Authentication Contents Overview..................................................... 3-2 Client Options.............................................. 3-3 General Features............................................
Configuring EtherChannels and Layer 2 Trunk Failover
35 CHAPTER Configuring EtherChannels and Layer 2 Trunk Failover This chapter describes how to configure EtherChannels on Layer 2 and Layer 3 ports on the switch. EtherChannel provides fault-tolerant high-speed
Configuring SPAN and RSPAN
41 CHAPTER This chapter describes how to configure the Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) on the Catalyst 4500 series switches. SPAN selects network traffic for analysis by a network
Configuring IGMP Snooping and MVR
CHAPTER 21 This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on the Cisco ME 3400 Ethernet Access switch, including an application of local IGMP snooping, Multicast
IP SLA Service Performance Testing
This module describes how to configure the ITU-T Y.1564 Ethernet service performance test methodology that measures the ability of a network device to enable movement of traffic at the configured data
Auto Identity. Auto Identity. Finding Feature Information. Information About Auto Identity. Auto Identity Overview. Auto Identity, page 1
, page 1 The feature provides a set of built-in policies at global configuration and interface configuration modes. This feature is available only in Class-Based Policy Language (CPL) control policy-equivalent
Configuring EtherChannels and Link-State Tracking
CHAPTER 37 Configuring EtherChannels and Link-State Tracking This chapter describes how to configure EtherChannels on Layer 2 and Layer 3 ports on the switch. EtherChannel provides fault-tolerant high-speed
Configuring IGMP Snooping
This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on a Cisco NX-OS device. About IGMP Snooping, page 1 Licensing Requirements for IGMP Snooping, page 4 Prerequisites
FiberstoreOS. IP Service Configuration Guide
FiberstoreOS IP Service Configuration Guide Contents 1 Configuring ARP... 1 1.1 Overview... 1 1.2 Configuring ARP... 1 1.3 Validation commands...2 2 Configuring Proxy ARP...4 2.1 Overview... 4 2.2 Configuring
Configuring VM-FEX. Information About VM-FEX. VM-FEX Overview. VM-FEX Components. This chapter contains the following sections:
This chapter contains the following sections: Information About VM-FEX, page 1 Licensing Requirements for VM-FEX, page 3 Default Settings for VM-FEX, page 3, page 4 Verifying the VM-FEX Configuration,
FSOS IP Service Configuration Guide
FSOS IP Service Configuration Guide Contents 1 Configuring ARP... 5 1.1 Overview... 5 1.2 Configuring ARP... 5 1.3 Validation commands...6 2 Configuring Proxy ARP...8 2.1 Overview... 8 2.2 Configuring
Configuring Virtual Port Channels
This chapter contains the following sections: Information About vpcs, page 1 Guidelines and Limitations for vpcs, page 10 Configuring vpcs, page 11 Verifying the vpc Configuration, page 25 vpc Default
Figure 7-1 Unicast Static FDB window
7. Layer 2 Features FDB VLAN Spanning Tree Loopback Detection Link Aggregation L2 Multicast Control LLDP FDB Static FDB Unicast Static FDB This window is used to view and configure the static unicast forwarding
Chapter 3 Lab 3-1, Spanning Tree Protocol (STP) Default Behavior
Chapter 3 Lab 3-1, Spanning Tree Protocol (STP) Default Behavior Topology Objective Background Observe the default behavior of STP. Four switches have just been installed. The distribution layer switches