Basic FXO Gateway Configuration
|
|
- Aron Powell
- 6 years ago
- Views:
Transcription
1 Mediatrix units with FXO ports Revision
2 Table of Contents Table of Contents Configuring the Mediatrix Unit 3 Getting Started 3 Logging On to the Mediatrix Unit Web Interface 3 Configuring the Default Servers 4 Registering Endpoints to All Gateways 5 Creating a Hunt Group 5 Creating a New Route 6 Configuring Automatic Call Activation on All FXO Ports 7 Configuring Automatic Call Activation on a Specific FXO Port 8 Configuring Country Selection 9 Configuring the Dial Tone Detection 9 Configuring the Answering Delay 10 Configuring the Far End Disconnect Parameters 11 Restarting Services 12 Available Documentation 13 Copyright Notice 14
3 3 Configuring the Mediatrix Unit Getting Started 1) Make sure the WAN network interface (either WAN, ETH1, Ethernet, Network, or ETH5 depending on your model) of your Mediatrix unit is connected to the network. 2) Make sure the second Ethernet connector (either LAN, ETH2, or Computer depending on your model) of your Mediatrix unit is connected to the computer. 3) Log on to the Mediatrix unit Management interface. Note: If you are using your Mediatrix unit for the first time, refer to its Mediatrix unit Quick Start guide. Logging On to the Mediatrix Unit Web Interface For better performances, it is recommended to use the latest available version of Microsoft Internet Explorer, Google Chrome or Mozilla Firefox. Note: You may not be able to log on to the Management Interface if you are using older browser versions. The computer's network card must be on the same subnet as the Mediatrix unit. 1) In your web browser, enter the IP address used by your Mediatrix unit to communicate with the Management Interface. If your computer is connected to the Ethernet port, commonly used to be connected to the Local Area Network (LAN), i.e. ETH2 on most devices, use the IP address. If your Mediatrix unit is configured to use a DHCP with IPv4, use the DHCP- provided IP address. 2) Enter public as your username and leave the password field empty. Note: The public username account has administrator rights. Note: You can also use admin as a username and administrator as password.
4 4 3) Click Login. The page of the Management Interface is displayed. Configuring the Default Servers (p. 4) Configuring the Default Servers Before you start In some instances, the configuration of the default servers may already be completed. Go to SIP>Servers. In the Registrar Host field, indicate the server IP address or FQDN to use for this gateway. In the Proxy Host field, indicate the server IP address or FQDN to use for this gateway. In the Messaging Server Host field, indicate the server IP address or FQDN to use for this gateway, if needed. 5) Leave the Outbound Proxy Host field empty unless specifically instructed to set a value. 1) 2) 3) 4) Note: Setting the address to :0 or leaving the field empty disables the outbound proxy host. 6) Click Apply. 7) Click Restart required services located at the top of the page.
5 5 Registering Endpoints to All Gateways (p. 5) Registering Endpoints to All Gateways 1) 2) 3) 4) 5) Go to SIP > Registrations. For each endpoint requiring authentication, repeat steps 2 and 3. From the Register selection list, select Enable. From the Gateway Name selection list, select All for each endpoint. Click Apply & Refresh. Creating a Hunt Group (p. 5) Creating a Hunt Group 1) Go to Call Router > Route Config.
6 6 2) In the Hunt table, click. 3) In the Name field, type FXO_Hunt. 4) From the dropbox next to the Destinations field, select fxo-fxo1, fxo-fxo2, fxo-fxo3, fxo-fxo4. 5) From the dropbox next to the Causes field, select the causes pertinent to your situation. 6) Click Save. Creating a New Route (p. 6) Creating a New Route Before you start The task Creating a Hunt Group (p. 5) must be completed. 1) 2) 3) 4) 5) 6) Go to Call Router > Route Config. In the Route table, click. From the dropbox next to the Sources field, select sip-default. From the dropbox next to the Destination field, select hunt-fxo_hunt. Click Save. In the Route table, click.
7 7 7) From the dropbox next to the Sources, select all the used FXO port. 8) In the Destination field, set sip-default. 9) Click Save to apply the new configuration. Configuring Automatic Call Activation on All FXO Ports (p. 7) Configuring Automatic Call Activation on All FXO Ports 1) 2) 3) 4) Go to Telephony > Services. Set the Select Endpoint selection list to Default. Set the Automatic Call Activation to Enable. Set the Automatic Call Target to the SIP server IVR or desired extension number.
8 8 Configuring Country Selection (p. 9) Configuring Automatic Call Activation on a Specific FXO Port Go to Telephony > Services. From the Select Endpoint selection list, select the FXO endpoint to configure. In the Automatic Call section, set the Endpoint Specific selection list to Yes. Set the Automatic Call Activation selection list to Enable. Set the Automatic Call Target selection list to the SIP server IVR or desired extension number. 6) Repeat the steps 2 to 5 for each FXO endpoint to configure. 7) Click Apply. 1) 2) 3) 4) 5) Calls form the selected endpoints lines will be sent to the configured destination number in the SIP server.
9 9 Configuring Country Selection 1) Go to Telephony > Misc. 2) In the Country table, select your country from the dropbox. 3) Click Apply. Configuring the Dial Tone Detection (p. 9) Configuring the Dial Tone Detection It allows the Mediatrix unit to wait for a dial tone before initiating the dialing sequence. If no dial tone is detected, the line is considered busy.if you are not familiar with the meaning of the fields, click Show Help, located at the upper right corner of the Web page, to display field description when mousing over the field name. 1) Go to POTS > FXO Configuration. 2) In the FXO Dialing Configuration table, from the Dial Tone Detection Mode dropbox, select CountryTone. Note: Not all PBX manufacturers produce the country dial tone on the extension line. If this is the case, make sure the Dial Tone Detection Mode is disabled, otherwise the Mediatrix unit will not output dialed digits.
10 10 Note: Not all PSTN switches produce the country dial tone on the PSTN line. If this is the case, make sure the Dial Tone Detection Mode is disabled, otherwise the Mediatrix unit will not output dialed digits. Configuring the Answering Delay (p. 10) Configuring the Answering Delay 1) Go to POTS > FXO Configuration. 2) In the FXO Answering Configuration table, complete the fields as required. Note: If the PBX does not pass the caller ID to the Mediatrix unit, you can reduce the Wait Before Answering Delay to 1000 to reduce the time before the Mediatrix unit goes offhook upon ring detection.
11 11 Configuring the Far End Disconnect Parameters (p. 11) Configuring the Far End Disconnect Parameters 1) Go to POTS > FXO Configuration. 2) In the FXO Force End of Call table, from the Force End Of Call On Tone Detection Mode dropbox, select Custom Tone. 3) Set the Tone Detection Custom Frequency field to 350. Note: Verify with your PBX supplier what tone (exact frequency and cadence) the PBX produces on the extension when the far end is disconnected. 4) Complete the other fields as required.
12 12 Restarting Services (p. 12) Restarting Services 1) Go to System > Services. 2) In the Restart required services table, click Restart required services.
13 Available Documentation For more details, refer to the Mediatrix Documentation. 13
14 14 Copyright Notice Copyright 2016 Media5 Corporation. This document contains information that is proprietary to Media5 Corporation. Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents. This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, without written prior approval by Media5 Corporation. Media5 Corporation reserves the right to revise this publication and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes.
15
Basic FXO Gateway Configuration
Mediatrix units with FXO ports v. 2.0.41.762 2017-12-21 Table of Contents Table of Contents Configuring the Mediatrix Unit 3 Getting Started 3 Logging on to the Mediatrix Unit Web Interface 3 Configuring
More informationBasic FXS Gateway Configuration
Mediatrix units with FXS ports Revision 308 2015-06-25 Table of Contents Table of Contents Configuring the Mediatrix Unit 3 Getting Started 3 Logging On to the Mediatrix Unit Web Interface 3 Configuring
More informationBasic SIP Username Registration
For all Mediatrix units with telephony cards v. 2.0.42.768 2018-04-03 Table of Contents Table of Contents Information to Know Before Starting 3 4 Logging on to the Mediatrix Unit Web Interface 4 Configuring
More informationBasic SIP Unit Registration
For all Mediatrix units with telephony cards v. 2.0.40.747 2018-03-29 Table of Contents Table of Contents Information to Know Before Starting 3 4 Logging on to the Mediatrix Unit Web Interface 4 Configuring
More informationBasic SIP Endpoint Registration
For all Mediatrix units with telephony cards v. 43.1.1264 2018-09-26 Table of Contents Table of Contents to Know Before Starting 3 4 Logging on to the Mediatrix Unit Web Interface 4 Configuring the Default
More informationPBX Remote Line Extension
FXO and FXS Mediatrix units v. 43.1.1264 2018-09-26 Table of Contents Table of Contents 4 Information to Know Before Starting 5 Connecting 6 Logging on to the Mediatrix Unit Web Interface 6 Configuring
More informationMediatrix 4400 Digital Gateway VoIP Trunking with a Legacy PBX. Mediatrix 4400
Mediatrix 4400 Digital Gateway VoIP Trunking with a Legacy PBX Mediatrix 4400 Dgw v2.0 Revision 283 - July 31, 2015 Table of Contents Table of Contents Copyright Notice 3 4 Requirements 6 Configuration
More informationMediatrix 4400 Digital Gateway ISDN Telephones
Mediatrix 4400 Revision 285 2011-06-22 Table of Contents Table of Contents 3 Requirements 5 Configuration of the Mediatrix 4400 Digital Gateway 6 Using IPv4 to Connect the Mediatrix unit to a Network with
More informationMediatrix 4400 Digital Gateway VoIP Gateway with the PSTN. Mediatrix 4400 Series
Mediatrix 4400 Series Revision 284 July 7,2015 Table of Contents Table of Contents Requirements 3 4 Configuration of the Mediatrix 4400 Digital Gateway 6 Using IPv4 to Connect the Mediatrix unit to a Network
More informationMediatrix 4400 Digital Gateway VoIP Gateway with the PSTN
Mediatrix 4400 Series v. 2.0.41.762 2017-12-21 Table of Contents Table of Contents Requirements 3 4 Configuration of the Mediatrix 4400 Digital Gateway 6 Connecting the Mediatrix Unit Using a DHCP Server
More informationRemote User - Mediatrix SBC on the Edge
Mediatrix Sentinel and Mediatrix 3000 v. 43.3.1398 2018-12-13 Table of Contents Table of Contents Information to Know Before Starting 4 Remote Users - Mediatrix SBC Located on the Edge 5 Getting Started
More informationRemote User - Mediatrix SBC on the Edge
Mediatrix Sentinel and Mediatrix 3000 v. 2.0.40.747 2018-03-29 Table of Contents Table of Contents to Know Before Starting 4 Remote Users - Mediatrix SBC Located on the Edge 5 Getting Started 5 Logging
More informationUsing a PSTN Mediatrix Gateway (FXO, PRI, BRI) with a 3CX IP PBX
Using a PSTN Mediatrix Gateway (FXO, PRI, BRI) with a 3CX IP PBX For Mediatrix 3000, C730, 4400, and G7 Gateways v. 43.0.1125 2018-08-16 Table of Contents Table of Contents Requirements 3 Information to
More informationSecond SIP Gateway Fallback with Gateway Registration
All Mediatrix units v. 2.0.41.762 2018-03-29 Table of Contents Table of Contents Information to Know Before Starting 3 Requirements 4 Second SIP Gateway Fallback 5 SIP Configuration 6 Adding the Fallback
More informationVLAN Configuration. All Mediatrix Products. Revision
All Mediatrix Products Revision 01 2016-07-19 Table of Contents Table of Contents Information to Know Before Starting 3 Getting Started 4 Logging On to the Mediatrix Unit Web Interface 4 Configuring the
More informationPSTN Survivability - Mediatrix SBC in the LAN with PBX Registering to the Mediatrix SBC
PSTN Survivability - Mediatrix SBC in the LAN with PBX Registering to the Mediatrix SBC For Mediatrix Sentinel and Mediatrix 3000 Revision 03 2016-01-13 Table of Contents Table of Contents to Know Before
More informationInterop- Mediatrix PRI FXO Gateway as a MS Lynx 2010 PSTN Gateway - Medatrix 3000 Series
Interop- Mediatrix PRI FXO Gateway as a MS Lynx 2010 PSTN Gateway - Medatrix 3000 Series Mediatrix 3000 series Revision 308 2015-06-25 Table of Contents Table of Contents Mediatrix as a trunking gateway
More informationPSTN Survivability - Mediatrix SBC in the LAN Registering to the Service Provider
PSTN Survivability - Mediatrix SBC in the LAN Registering to the Service Provider For Sentinel and Mediatrix 3000 units v. 2.0.40.747 2017-09-29 Table of Contents Table of Contents to Know Before Starting
More informationDual Trunk Survivability - Mediatrix SBC in the LAN with Static PBX IP Address
Dual Trunk Survivability - Mediatrix SBC in the LAN with Static PBX IP Address For Mediatrix Sentinel and Mediatrix 3000 Revision 04 2016-02-05 Table of Contents Table of Contents to Know Before Starting
More informationDGW PCM Traces. All Mediatrix Units. v
All Mediatrix Units v. 2.0.40.747 2018-03-29 Table of Contents Table of Contents PCM Traces 3 Requirements 4 Enabling the PCM Traces - DGW 2.0 5 Enabling PCM Traces in the Configuration Script 5 Enabling
More informationUsing a Mediatrix Gateway with a 3CX IP PBX
For the Mediatrix C710, C711, and 4102S Revision 01 2017-03-14 Table of Contents Table of Contents Requirements 3 Information to Know Before Starting 4 Configuration on the 3CX Server Side 5 Installing
More informationBasic FXO Mediatrix Unit Configuration with Asterisk
Mediatrix Unit with FXO Card v. 2.0.40.747 2018-03-29 Table of Contents Table of Contents Mediatrix unit with Asterisk 4 Requirements 5 to Know Before Starting 6 Configuration of the PBX Trunk 7 Configuring
More informationSecond SIP Fallback with Gateway Registration
Second SIP Fallback with Gateway Registration For all Mediatrix units Revision 03-2015-10-28 www.media5corp.com Second SIP Fallback with Gateway Registration Table of Contents Second SIP Gateway Fallback...3
More informationSecond SIP Gateway Fallback with Endpoint Registration
Second SIP Gateway Fallback with Endpoint Registration For Mediatrix C7,Mediatrix 4100, Mediatrix Sentinel, and Mediatrix LP series Revision 3-2015-12-17 www.media5corp.com Second SIP Gateway Fallback
More informationMediatrix FXO Unit with Asterisk
Mediatrix 3000 series, Mediatrix C7 series, and Mediatrix Sentinel Revision 296 2015-06-29 Table of Contents Table of Contents Mediatrix FXO unit with Asterisk 4 Requirements 5 Configuration of the PBX
More informationConfiguring an FXO Mediatrix Gateway as a MS Lync 2010 PSTN Gateway
Configuring an FXO Mediatrix Gateway as a MS Lync 2010 PSTN Gateway Mediatrix units with FXO ports v. 43.1.1264 2018-09-26 Table of Contents Table of Contents to Know Before Starting 3 Mediatrix Gateway
More informationSIP Gateways. For all Mediatrix units. v
SIP Gateways For all Mediatrix units v. 43.3.1398 2018-12-18 Table of Contents Table of Contents SIP Gateways 3 Important Information to Know before Using SIP Gateways 3 Trunk Gateway vs Endpoint Gateway
More informationFirst Aid. For All Mediatrix units. Revision
For All Mediatrix units Revision 01 2015-09-30 Table of Contents Table of Contents Troubleshooting 3 Troubleshooting 3 Mediatrix Profile Default Settings for the Rescue Interface 4 Performing a Factory
More informationQuick Installation Guide
Quick Installation Guide BRI Gateway Version 2.1 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Creating SIP Trunks... 3 Creating BRI Trunks... 4 Call Routing Rules... 4 Hardware Setup
More informationFirst Aid. For All Mediatrix units. v
For All Mediatrix units v. 2.0.40.747 2018-03-29 Table of Contents Table of Contents Troubleshooting 3 Troubleshooting 4 Mediatrix Profile Default Settings for the Rescue Interface 4 Performing a Factory
More informationConfiguration Notes 281
Mediatrix 3000 Digital Gateway Corporate Network June 21, 2011 Proprietary 2011 Media5 Corporation Table of Contents Configuration Notes 281... 1 Introduction... 3 Mediatrix 3000 Digital Gateway Overview...
More informationConfiguring the Grandstream UCM6202 for use with TopView Voice Notification Updated August 2018
Configuring the Grandstream UCM6202 for use with TopView Voice Notification Updated August 2018 Contents Introduction... 2 Voice Notification in TopView... 2 Options for using VOIP in TopView... 2 How
More informationFirst Aid. For All Mediatrix units. v
For All Mediatrix units v. 43.0.1125 2018-08-16 Table of Contents Table of Contents Troubleshooting 3 Troubleshooting 4 Mediatrix Profile Default Settings for the Rescue Interface 4 Performing a Factory
More informationConfiguration Notes 284
Mediatrix 4400 Digital Gateway VoIP Gateway with the PSTN June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Mediatrix 4400 Digital Gateway Overview... 3 Deployment Scenario...
More informationFirst Aid. For All Mediatrix units. v
For All Mediatrix units v. 2.0.41.762 2018-03-29 Table of Contents Table of Contents Troubleshooting 3 Troubleshooting 4 Mediatrix Profile Default Settings for the Rescue Interface 4 Performing a Factory
More informationSbc Service User Guide
For Mediatrix Sentinel and Mediatrix 3000 Revision 04 2016-01-13 Table of Contents Table of Contents Configuration notes 5 Call Agents 6 phone_lines_ca Call Agent 8 trunk_lines_ca Call Agent 9 local_users_ca
More informationMediatrix Sentinel Quick Start. Dgw v January 30,
Dgw v2.0.30.549 January 30, 2015 www.media5corp.com Table of Contents The Mediatrix Sentinel Quick Start...3 Using the Mediatrix Sentinel on the Edge... 4 Using the Mediatrix Sentinel in the LAN without
More informationAnalog Telephone Adapter Setup for Q-SYS Softphone
Analog Telephone Adapter Setup for Q-SYS Softphone This document applies to this Cisco device: SPA232D Introduction This document covers the use of the SPA232D in the role of analog telephone adapter (ATA)
More informationInternet Telephony PBX System IPX Quick Installation Guide
Internet Telephony PBX System IPX-2000 Quick Installation Guide Overview PLANET IPX-2000 is the next generation voice communication platform for the small to medium enterprise. Designed as an open, scalable,
More informationConfiguring the DHCP Server
For all DGW Platforms v. 2.0.42.768 2018-05-17 Table of Contents Table of Contents DHCP Service Starting the DHCP Server Documentation 5 Copyright Notice 6 DHCP Service The DHCP service allows the Mediatrix
More informationGXW410X FXO Gateway (Firmware Revision )
Published on Documentation (https://www.emetrotel.com/tsd) Home > GXW410X FXO Gateway (Firmware Revision 1.4.1.4) GXW410X FXO Gateway (Firmware Revision 1.4.1.4) Gateway Setup Step One: Accessing the Gateway
More informationQuick Installation Guide
Quick Installation Guide IP/PRI/FXS/BRI PBX Version 2.1 Quick Installation Guide v2.1 www.cem-solutions.net 2 Table of Contents Initial Setup of IP/PRI/FXS/BRI PBX... 4 Notification LEDs (On the Front
More informationEP502/EP504 IP PBX 1.1 Overview
1.1 Overview The EP502/EP504 is an embedded Voice over IP (VoIP) Server with Session Initiation Protocol (SIP) to provide IP extension phone connection for global virtual office of small-to-medium business
More informationInternet Telephony PBX System. (30/100/200/500 SIP Users Registrations) IPX-330/IPX-2100/IPX-2200/IPX Quick Installation Guide
Internet Telephony PBX System (30/100/200/500 SIP Users Registrations) IPX-330/IPX-2100/IPX-2200/IPX-2500 Quick Installation Guide Table of Contents 1. Internet Telephony PBX System... 3 1.1. Package Contents...
More informationConfiguring PPP And SIP
Copyright Copyright 2005. All rights reserved. The content of this manual is subject to change without notice. The information and messages contained herein are proprietary to. No part of this manual may
More informationPatton SN4960 and Elastix Server
Patton SN4960 and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Patton SN4960 gateway configuration. We re going to configure a SIP Trunk
More informationSetting up the Grandstream Gateway for use with STAC VIP
Setting up the Grandstream Gateway for use with STAC VIP Introduction The GXW4108 Gateway is a cost-effective way of converting the Comrex STAC VIP to use with POTS (or PSTN) telephone lines. The gateway
More informationInSciTek Microsystems 635 Cross Keys Park Fairport, NY Guide to New Features Release 4.5
InSciTek Microsystems 635 Cross Keys Park Fairport, NY 14450 585-421-3850 Guide to New Features Release 4.5 Table of Contents Defining Resources...1 Adding an Outside Line...1 Adding Direct Inward Dialing...4
More informationCall Router Basic Routes
All Mediatrix Products Revision 01 2016-05-27 Table of Contents Table of Contents Creating Basic Routes 3 Creating a Hunt Group 3 Creating a Route from a Sip Gateway to a Destination 4 Creating a Route
More informationSangoma Vega FXS/2FXO and Elastix Server
Sangoma Vega 5000 24FXS/2FXO and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Vega 5000 analog gateway configuration. We re going to configure
More informationConfiguring Patton SmartNode FXO VoIP Gateway
Source: https://www.3cx.com/voip-gateways/patton-smartnode-sn4112/ Configuring Patton SmartNode FXO VoIP Gateway Supported Models: Patton SmartNode SN4112 / SN4114 FXO After you familiarize yourself with
More informationManual PBX IP Version: 1.0
Manual PBX IP 2008 Version: 1.0 Content CONTACT ATCOM... 3 CHAPTER 1 THE INTRODUCTION OF PBX-IP 2008... 4 CHAPTER 2 ACCESS TO THE PBX-IP 2008... 7 2.1 WEB PAGE ACCESS BY BROWSER... 7 2.2 SSH ACCESS BY
More informationWellGate 2504 ( 4-FXS ) and WellGate 2540 (4-FXO gateway) in Peer to Peer mode with Hotline by port to port application.
WellGate 2504 ( 4-FXS ) and WellGate 2540 (4-FXO gateway) in Peer to Peer mode with Hotline by port to port application. Note : Please use Windows XP IE 6.0 web browser or above version to configure both
More informationDNS SRV Usage. All Mediatrix Units
All Mediatrix Units Revision 663July 23, 2015 Table of Contents Table of Contents 3 DNS SRV ( RFC 2782) 4 Type A Query 5 Type A Query to a SRV Record 7 Type SRV Query 9 The Effects of Priority and Weight
More informationATCOM IPPBX IP01 Product Guide Version: VoIPon Tel: +44 (0) Fax: +44 (0)
Figure: ATCOM IPPBX IP01 ATCOM IPPBX IP01 Product Guide Version: 1.0 2010-05-10 Content CONTACT ATCOM... 3 CHAPTER 1 THE INTRODUCTION OF IP01... 4 CHAPTER 2 ACCESS TO THE IP01... 6 2.1 WEB PAGE ACCESS
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
More informationGrandstream Networks, Inc. Configuring UCM6XXX Series with HT503with
Grandstream Networks, Inc. with Table of Contents OVERVIEW... 4 METHOD 1: REGISTER HT503 TO UCM6XXX... 5 Create Extension on UCM6XXX... 5 Create IVR on UCM6XXX... 6 Configure FXS Port on HT503... 7 Configure
More informationGrandstream IP Phone Configuration Guides
Grandstream IP Phone Configuration Guides Version 1.0 Yeastar Information Technology Co. Ltd. Table of Contents FOR GRANDSTREAM GXP SERIES... 3 Register with MyPBX... 3 Provisioning for MyPBX... 5 Phone
More informationSoLink-Lite IP-PBX. Administrator Guide. (Version 1.0)
SoLink-Lite IP-PBX Administrator Guide (Version 1.0) TABLE OF CONTENT 1.0 Introduction... 1 2.0 Setting Up the IP-PBX... 2 3.0 Logging On... 3 4.0 Configuring Network... 4 5.0 Configuring Hardware... 5
More informationISDN Troubleshooting. All Mediatrix Units with ISDN cards
All Mediatrix Units with ISDN cards Revision 671 July 24, 2015 Table of Contents Table of Contents 4 Protocols and Connection 5 Troubleshooting Tools 6 Troubleshooting 6 Capturing a Trace Using Wireshark
More informationInternet Telephony PBX System. (30/100/500 SIP Users Registrations) IPX-330 / IPX-2100 / IPX Quick Installation Guide
Internet Telephony PBX System (30/100/500 SIP Users Registrations) IPX-330 / IPX-2100 / IPX-2500 Quick Installation Guide Table of Contents 1. IPX-330... 3 1.1. Package Contents... 3 1.2. Hardware Installation...
More informationInternet Telephony Gateway VGW-402 / VGW-400FS / VGW-400FO. Quick Installation Guide
Internet Telephony Gateway VGW-402 / VGW-400FS / VGW-400FO Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Hardware Installation... 4 2.1 Safety Instructions... 4 2.2 Physical Introduction...
More informationAG/SR 2330 Installation Reference
SCS 4.0 AG/SR 2330 Installation Reference Task Based Guide Copyright 2010 Avaya Inc. All Rights Reserved. Notices While reasonable efforts have been made to ensure that the information in this document
More informationCisco Unified Communications UC320W Pre-Installation Site Information
Cisco Unified Communications UC320W Pre-Installation Site Information Use this workbook to gather information from your customer before you install the Cisco Unified Communications UC320W at the site.
More informationFigure: ATCOM IPPBX IP04. ATCOM IPPBX IP04 Product Guide Version:
Figure: ATCOM IPPBX IP04 ATCOM IPPBX IP04 Product Guide Version: 1.0 2010-05-10 Content CONTACT ATCOM... 3 CHAPTER 1 THE INTRODUCTION OF IP04... 4 CHAPTER 2 ACCESS TO THE IP04... 7 2.1 WEB PAGE ACCESS
More informationStep 3 - How to Configure Basic System Settings
Before configuring the IP address and network settings, complete Step 2 - How to Configure IP Address, network Settings, and Firewall. Verify the computer and the are connected to the same network, with
More informationConfiguring Local Firewalls
All Mediatrix Products v. 43.3.1398 2019-01-10 Table of Contents Table of Contents Local Firewall 3 Firewall Rule Order - Important 3 Configuring the Local Firewall 4 Disabling the Local Firewall 5 Configuring
More informationCONFIGURING GRANDSTREAM IP PHONES AND GATEWAYS WITH THE 3CX PHONE SYSTEM
CONFIGURING GRANDSTREAM IP PHONES AND GATEWAYS WITH THE 3CX PHONE SYSTEM CONFIGURING GRANDSTREAM GXP SERIES WITH THE 3CX PHONE SYSTEM 1. Ensure that you have created the extension that you wish to use
More informationGrandstream Networks, Inc. UCM6200 Basic Configuration Guide
Grandstream Networks, Inc. Table of Contents OVERVIEW... 4 SETUP GUIDE SCENARIO... 4 QUICK INSTALLATION... 5 Connecting the UCM6200... 5 Access UCM6200 series Web Interface... 5 CREATE USER EXTENSION...
More informationBroadvox Fusion SIP Trunks Configuration Guide PBX Platform: KX-TDA50
Broadvox Fusion SIP Trunks Configuration Guide PBX Platform: KX-TDA50 3/20/2013 1 Overview This document describes the configuration procedures required for the KX-TDA50 to make full use of the capabilities
More informationISDN Troubleshooting. All Mediatrix Units with ISDN cards. v
All Mediatrix Units with ISDN cards v. 2.0.41.762 2018-03-29 Table of Contents Table of Contents 4 Protocols and Connection 5 Troubleshooting Tools 6 Troubleshooting 6 Capturing a Trace Using Wireshark
More informationHangzhou Synway Information Engineering Co., Ltd
1 2 1. Abstract Elastix is an Open Source Software to establish Unified Communications. About this concept, Elastix goal is to incorporate all the communication alternatives, available at an enterprise
More informationSipura SPA 3000 How To. (c) Bicom Systems
Sipura SPA 3000 How To Sipura SPA 3000 How To All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording,
More informationHtek IP Phone Configuration Guides
Htek IP Phone Configuration Guides Version 1.0 Yeastar Information Technology Co. Ltd. Contents 1. Introduction... 3 2. Register with MyPBX Manually... 4 2.1 Register SIP Extension... 4 2.1 Configuring
More informationWelltech WellGate User Manual
Welltech WellGate 2626 An Easy to Use PBX Gateway User Manual Copyright 2009 Welltech Computer Co., Ltd. All right reserved Table of Contents Introduction...2 WellGate 2626 - An Easy to Use PBX Gateway...2
More informationApplication Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the configuration
More informationSMG1002-2S VOIP Gateway. Installation Manual VER 1.5
SMG1002-2S VOIP Gateway Installation Manual VER 1.5 Sywnay Information Engineering Co.,Ltd www.synway.net CONTENT 1.Appearance Description... 2 1.1 Front Panel... 2 1.2 Rear Panel... 2 2.Hardware Connection...
More informationANSEL FXS / 1 PSTN. VoIP Telephone Adaptor. User Manual V1.10
ANSEL 5518 1 FXS / 1 PSTN VoIP Telephone Adaptor User Manual V1.10 Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections for ANSEL 5518 A. Connect ANSEL 5518 WAN port to ADSL NAT Router as the following
More informationSPA400 Internet Telephony Gateway with 4 FXO Ports
SPA400 Internet Telephony Gateway with 4 FXO Ports Administration and Configuration Guide v1.0 Using the SPA400 The SPA400 features the ability to connect up to four (4) standard analog telephones lines
More information4 Port IP-PBX + SIP Gateway System
4 Port IP-PBX + SIP Gateway System The IPG-40XG is an embedded Voice over IP (VoIP) PBX Server with Session Initiation Protocol (SIP) to provide IP extension phone connections for global virtual office
More informationSangoma Vega 4000 E1/T1
Sangoma Vega 4000 E1/T1 and Elastix Server Setup Guide http://www.elastix.org PaloSantoo Solutions 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Vega 400 gateway configuration. We re going
More informationCCS-UC-1 SIP Endpoint with ShoreTel Connect System Configuration Guide Crestron Electronics, Inc.
CCS-UC-1 SIP Endpoint with ShoreTel Connect System 21.80.7840.0 Configuration Guide Crestron Electronics, Inc. Crestron product development software is licensed to Crestron dealers and Crestron Service
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
Cisco SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationidor Mobile Setup idor Mobile : idor Mobile System Manual V1.1 1
idor Mobile Setup Table of Contents Login into the Web-GUI... 3 Network Settings... 4 Set Static IP Address... 5 Apartments... 7 Add an Apartment... 7 Edit an Apartment... 9 Delete an Apartment... 9 SIP
More informationGrandstream Networks, Inc. Configuring UCM6XXX with GXW410X
Grandstream Networks, Inc. Table of Contents OVERVIEW... 4 CONNECT UCM6XXX TO GXW410X USING PEER SIP TRUNK... 5 Create IVR On UCM6XXX... 5 Create Peer SIP TRUNK On UCM6XXX... 5 Configure Outbound Rule
More informationCbeyond SIP Trunks Configuration Guide PBX Platform: KX-TDA50
Cbeyond SIP Trunks Configuration Guide PBX Platform: KX-TDA50 7/17/2009 1 Overview This document describes the configuration procedures required for the KX-TDA50 to make full use of the capabilities of
More informationSPA 8800 with 3CX PBX Server English Version
SPA 8800 with 3CX PBX Server English Version Avanzada 7, S.L. 1 / 14 ÍNDICE 1. Introduction... 3 2. SPA 8800 FXO configuration at 3CX... 3 3. FXS SPA 8800 configuration in 3CX... 6 3. FXO SPA 8800 registration
More informationTHINKTEL COMMUNICATIONS PATTON SMART NODE 4990 PRI OVER IP SIP TRUNKING
THINKTEL COMMUNICATIONS PATTON SMART NODE 4990 PRI OVER IP SIP TRUNKING TA B L E O F C O N T E N T S 1.1 NETWORK DIAGRAM... 3 1.2 CONNECTING THE SMARTNODE TO YOUR PC... 4 1.3 LOGIN TO THE SMARTNODE BY
More informationHow to Connect MyPBX to NeoGate TA FXS Gateway
How to Connect MyPBX to NeoGate TA FXS Gateway Version: 1.0 Yeastar Technology Co., Ltd. Date: 2014.07.22 http://www.yeastar.com 1/16 Table of Contents: 1. Introduction... 3 2. Preparation... 4 3. VoIP
More informationYealink IP Phone Configuration Guides. Yeastar Technology Co., Ltd.
Yealink IP Phone Configuration Guides Yeastar Technology Co., Ltd. Table of Contents Register with MyPBX manually... 3 Configuring BLF on Yealink... 6 Provisioning for MyPBX... 8 3.1 Phone provisioning
More informationISDN Troubleshooting. All Mediatrix Units with ISDN cards. v
All Mediatrix Units with ISDN cards v. 43.3.1398 2019-01-10 Table of Contents Table of Contents 4 Protocols and Connection 5 Troubleshooting Tools 6 Troubleshooting 6 Capturing a Trace Using Wireshark
More informationApplication Notes for ClearOne MAX IP and MAXAttach IP with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for ClearOne MAX IP and MAXAttach IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required
More information1 Package Contents 2 Hardware Installation 2.1 Safety Precautions 2.2 Physical Connection 2.3 LED Definitions 3 Basic System Configuration 3.
ETH G 1 Package Contents 2 Hardware Installation 2.1 Safety Precautions 2.2 Physical Connection 2.3 LED Definitions 3 Basic System Configuration 3.1 Web Login 3.2 Network Configuration 3.3 Reset to factory
More informationNF3ADV VoIP Setup Guide (for Dodo)
NF3ADV VoIP Setup Guide (for Dodo) Configuring your NF3ADV for Dodo VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already
More informationIPitomy IP PBX Server: Cyberdata VoIP V2 Ceiling Speaker Configuration Guide
IPitomy IP PBX Server: Cyberdata VoIP V2 Ceiling Speaker Configuration Guide Document Part #930337A CyberData Corporation 2555 Garden Road Monterey, CA 93940 (831) 373-2601 www.cyberdata.net 1 1.0 Instructions
More informationWAN. System Networking Lab Table 1
System Networking Lab Table 1 In this diagram each system operates independently to supply network services to the phones on its LAN interface. The phones are powered by a Power over Ethernet switch. The
More informationApplication Notes for Komutel CCS with Avaya IP Office - Issue 1.1
Avaya Solution & Interoperability Test Lab Application Notes for Komutel CCS with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the steps required to integrate Komutel CCS (Call
More informationPlease note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system.
Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please follow these steps to ensure that any changes made by your previous
More informationApplication Note 3Com VCX Connect with SIP Trunking - Configuration Guide
Application Note 3Com VCX Connect with SIP Trunking - Configuration Guide 28 May 2009 3Com VCX Connect Solution SIP Trunking Table of Contents 1 3COM VCX CONNECT AND INGATE... 1 1.1 SIP TRUNKING SUPPORT...
More informationFirst Aid. For all Mediatrix units. Revision
First Aid For all Mediatrix units Revision 01-2015-09-30 www.media5corp.com First Aid Table of Contents Troubleshooting... 3 Troubleshooting... 3 Mediatrix Profile Default Settings for the Rescue Interface...
More information