SANGFOR WANO POC Guideline

Size: px
Start display at page:

Download "SANGFOR WANO POC Guideline"

Transcription

1 SANGFOR WANO POC Guideline 1. The preparation before the testing and deployment The network environment checklist URL: cklist_v xlsx High end device testing procedure: For M5500 above, please follow this guideline. Hardware Inspection 1. Please make sure that we use the original box to store the box when we directly go to customer site for testing/deployment. Do not recommend to bring device without boxes to customer site. 2. Please check device appearance, any part fall off inside the device, any water stains was on the device. 3. Please check the interface port connection is in good condition. 4. If the deployment needs fiber port, please confirm the type of the fiber module and

2 prepare the fiber module or fiber to electrical module converter. 5. If we need hardware bypass feature, please confirm the bypass port working status By default, eth0 and eth2 is a pair of hardware bypass port. After deployed IAM in bridge mode, turn off the power, if PC from eth0 can ping to front end interface or public IP, the bypass feature is working normal. Attention: Only M5500-AC above can support bypass feature. Do not connect a pair of bypass interface to a same switch, it will cause the looping. In bypass mode, do not connect same pair of bypass interface as mirror port in switch, it will cause the looping too. Software Inspection 1 Verify the latest official firmware version, if have customization patch, please prepare it before the testing/deployment. 2 Check whether device is upgraded with latest gateway patch. 3 Factory reset the device before the testing/deployment. 4 Verify that device is accessible via web console and gateway updater Verify the device date and time, please change it if found the value is different. 6 Verify the Serial Number (SN) of the device. If we need to exchange the interface, please apply license early. 7 Verify the device multifunction license, whether the required license was opened? 8 Verify the system log, any abnormality log? 9 Verify the internal data center is accessible? Any log inside the internal data center? If yes, please clear all those logs. 10 Verify the internal rules database is up-to-date? If not, please update the database. Obtain customer contact detail Include: Company name, mailing address, contact person, telephone.

3 Compare our test result with other vendor products. Before the testing, it is recommended to know thatwhether customer has tested the similar product from other vendor, any problem encountered during the usage. According to the required product features, we can analysis whether our device will be encountered similar problems, thus it is advisable to do the preparation to avoid problems. Implementation of the solution and project acceptance consideration Before we propose the solution, we must communicate with customer to make sure the implementation contents and method is follow the customer requirement. The project acceptance needs the mutual agreement with customer, and acceptance documentation must submit in accordance with customer expectations. On-site appointment Confirm the data and time with customer to ensure we have the customer s assistance support that familiar with their internal network. Installation material Prepare the device material, Exp: notebook, cross cable, common software and etc. Device installation standard (1)Site installation preparation Requirements Standard working temperature/humidity Input voltage requirements Immunity requirements grounding system Rack Actual content 0~45, 5~90% humidity, non-condensing V Away from high power radio transmitters, radar transmitters, high frequency and high current devices. Grounding requirements are the basis for stable and reliable operation of the equipment. Recommended grounding resistance value should be less than 5 ohms. Ventilation, strong load-bearing, well grounded.

4 Power supply Please refer to the product hardware parameters document. (2)Attention Attention Power supply Tool Before install on the rack Actual contents 1:Verify the working area isa potential danger,such aspower supply no grounding, grounding power is not unreliable, ground moisture. 2:Before installation, please make sure the emergency switch location to turn off it during emergency. 3:Please do not place the device in a humid place, and do not let liquid into the chassis. Prepare some locksmith tools. (Screwdriver, Crystal head crimping tools 1:Login device via management interface or DMZ interface and verify the configuration before install on the rack. 2:Do not connect desktop, laptop and Sangfor device directly to customer network during the configuration. If needed, please request the IP address allocation from the administrator to avoid IP conflict. Device Installation Requirement Moving equipment Installation of equipment Power cord Labeling Checklist Disconnect all power cords and external cables before move out the equipment. 1:Model M5500 above must install system tray. 2:In case users do not have the standard rack, you can install the device on a clean work surface. And ensure the installation is firm enough, enough to bear the weight of equipment and cables, 10cm distance around the device for heat dissipation. 3:Can t place heavy objects on the device. 4:Pay attention to other devices in the same cabinet, avoiding the installation process knocked the other devices, cable interface If device with redundant power supplies, it must connect the redundant power supply. Cables must be labeled and marked 1: Power cord Tags: Content is the cable position information, fill in the label located on the cable side of the end devices, control cabinets, junction box or outlet location information. 2:Signal line labels: label identifies the port connection of both cable ends. 3:Write/print the text content in the label sticker before paste the

5 Grounding label. When the device with DC power supply, it is necessary to install grounding for the device. The ground wire connected to the equipment s grounding screw while the other end connected above the rack. It is recommended to do the grounding for AC power supply scenario. Device safety Inspection Item Before power on device Power on device After power on device Checklist 1:Network equipment is mounted steadily. 2:All communication cables, optical fibers and power cable and ground cable are in good connections 3:Power supply voltage is consistent with the requirements of network equipment. 1:Turn on power supply 2:Turn on device power supply switch 1:After device powered on, ventilation system is working, wecan hear the sound of the fan rotation and air discharge from vents. 2:View various indicators of the device panel systems are normal. Bypass Function Testing All bypass supported devices, when deployed in bridge mode must test this function is effective or not to avoid hardware failure caused the customer business interruption. Recommended test method is as follows: bypass interface defaults is LAN port and WAN port, deployed device, turn off the power. From a computer connected to the LAN port and ping the front device interface or ping public IP, if you can ping, which means bypass function effective. Standard Configuration of every deployment Purpose By go through basic configuration, can guarantee SANGFOR working normally after deployed in customer network. IPSEC VPN tunnel or accelerating channel can be

6 established, customer's business systems can operate normally. Standard Configuration of Route mode Deployment Route Mode Internet + Single network segment Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN interface and connect ISP device with WAN interface. 3 Verify LED state is normal or not( Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Service Mode select Gateway, configure WAN IP, default gateway, LAN IP, Subnet Mask and DNS. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary

7 Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password. 7 Click on [Status]-[VPN] to check VPN connection. 8 Test VPN connection. 9 Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 11 If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 12 Click on [Status] to check acceleration status. 13 Test Acceleration effect.

8 Route Mode Internet + Multiple Network Segment Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN interface and connect ISP device with WAN interface. 3 Verify LED state is normal or not( Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Service Mode select Gateway, configure WAN IP, default gateway, LAN IP, Subnet Mask and DNS. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary

9 Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password. 7 Go to[sangfor VPN] [Advanced] [VPN Local Subnet], click NEW add in others VLAN info. 8 Go to [System] [Routing] [Static Route], add in all VLAN and gateway point to Core Switch. 9 Make sure in Core Switch have route peer network all subnet to WANO. 10 Click on [Status]-[VPN] to check VPN connection. 11, Test VPN connection. 12, Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 14, If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure Transfer Protocol. peer device name, Username, Password, IP Address, Listening Port, 15, Click on [Status] to check acceleration status. 16, Test Acceleration effect.

10 Route Mode Lease Line + Single Network Segment Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN interface and connect ISP device with WAN interface. 3 Verify LED state is normal or not( Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Service Mode select Gateway, configure WAN IP, default gateway, LAN IP, Subnet Mask and DNS. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User

11 Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password. 7 Click on [Status]-[VPN] to check VPN connection. 8 Test VPN connection. 9 Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 11 If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 12 Click on [Status] to check acceleration status. 13 Test Acceleration effect Route Mode Leased Line + Multiple Network Segment Network Topology

12 Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN interface and connect ISP device with WAN interface. 3 Verify LED state is normal or not( Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Service Mode select Gateway, configure WAN IP, default gateway, LAN IP, Subnet Mask and DNS. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password. 7 Go to[sangfor VPN] [Advanced] [VPN Local Subnet], click NEW add in others VLAN info. 8 Go to [System] [Routing] [Static Route], add in all VLAN and gateway point to Core Switch. 9 Make sure in Core Switch have route peer network all subnet to WANO. 10 Click on [Status]-[VPN] to check VPN connection. 11, Test VPN connection. 12, Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 14, If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW,

13 configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 15, Click on [Status] to check acceleration status. 16, Test Acceleration effect. Bridge Mode Deployment Standard Configuration Bridge Mode Single Segment Configuration Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN interface. 3 Verify LED state is normal or not( Link LED stayed on and Act LED blinking means interface working fine)

14 Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Deployment Mode select bridge, configure Bridge IP, default gateway, Subnet Mask, DNS Server and DMZ IP address. 4, Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to [WAN Optimization]-[Server], define acceleration policy, policy group & acceleration user. 6,If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 7, Click on [Status] to check acceleration status. 8, Test Acceleration effect.

15 Bridge Mode Multiple Segment Configuration Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN interface. 3 Verify LED state is normal or not (Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Deployment Mode select bridge,

16 configure Bridge IP, default gateway, Subnet Mask, DNS Server and DMZ IP address. 4, Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to [WAN Optimization]-[Server], define acceleration policy, policy group & acceleration user. 6,If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 7, Click on [Status] to check acceleration status. 8, Test Acceleration effect Double Bridge Mode Standard Configuration Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN1 & WAN2 interface. 3 Verify LED state is normal or not (Link LED stayed on and Act LED blinking means interface working fine)

17 Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Deployment Mode select Double Bridge, configure Both Bridge IP, default gateway, Subnet Mask, DNS Server and DMZ IP address. 4, Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerating. Go to [WAN Optimization]-[Server], define acceleration policy, policy group & acceleration user. 6,If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address(any bridge IP of double bridge deployment), Listening Port, Transfer Protocol. 7, Click on [Status] to check acceleration status. 8, Test Acceleration effect.

18 Single Arm + Single network segment Single Arm + Single network Segment Standard Configuration Network Topology Internet Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN1 & WAN2 interface. 3 Verify LED state is normal or not (Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin

19 3 Open [System]-[Network]-[Deployment],Deployment Mode select Single Arm, configure IP, default gateway, Subnet Mask, DNS Server and DMZ IP address. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password 7 Configure front-end device ( Firewall or Router) mapping TCP & UDP port to WANO LAN interface IP. 8 Configure static route from Firewall or Core switch, route peer network segment to WANO LAN IP as a gateway. 9 Click on [Status]-[VPN] to check VPN connection 10 Test VPN connection 11 Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 13 If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 14 Click on [Status] to check acceleration status. 15 Test Acceleration effect Single Arm + Multi network segment

20 Single Arm + Multi network segment configuration standard Network Topology Internet Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN1 & WAN2 interface. 3 Verify LED state is normal or not (Link LED stayed on and Act LED blinking means interface working fine) Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Deployment Mode select Single Arm,

21 configure Bridge IP, default gateway, Subnet Mask, DNS Server and DMZ IP address. 4 If Device deploy as VPN server, open [Sangfor VPN]-[Server], configure Primary Web agent address and VPN listening port (default is 4009) 5 If there is mobile VPN user, open [Sangfor VPN]-[Server]-[Virtual IP Pool], configure available IP as Virtual IP pool for mobile VPN user. After that open [Sangfor VPN]-[Server]-[VPN User], add New user, configure Username, Password and select User Type either Branch or Mobile user. 6 If Device deploy as Branch VPN, go to [Sangfor VPN]-[Client], Click New, fill in Primary WebAgent address, Transfer protocol, Username & Password 7 Open [Sangfor VPN] [Advanced] [VPN Local Subnet], add all VLAN segment in this site except WANO LAN segment. 8, Open [System] [Network] [Local Subnet], add all VLAN segment in this site except WANO LAN segment. 9, Configure static route from Firewall or Core switch, route peer network segment to WANO LAN IP as a gateway. 10 Configure front-end device ( Firewall or Router) mapping TCP & UDP port to WANO LAN interface IP. 11 Click on [Status]-[VPN] to check VPN connection 12 Test VPN connection 13 Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerate. Go to[wan Optimization]-[Server], define acceleration policy, policy group & acceleration user. 15 If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, IP Address, Listening Port, Transfer Protocol. 16 Click on [Status] to check acceleration status. 17 Test Acceleration effect

22 Double Arm Deployment Leased line Double Arm Deployment Configuration Standard Network Topology Wiring Standard 1 Connect power cord and power on device. 2 Connect switch with LAN & DMZ interface and connect front-end device with WAN1 & WAN2 interface. 3 Verify LED state is normal or not (Link LED stayed on and Act LED blinking means interface working fine)

23 Basic Configuration Standard 1 PC IP configure same segment with WANO LAN IP, LAN IP default is: /24, use cross-over cable to connect WANO. 2 Open IE browser and enter: to login,username:admin Password:Admin 3 Open [System]-[Network]-[Deployment],Deployment Mode select Double Arm, configure IP, default gateway, Subnet Mask, DNS Server both arm and DMZ IP address. 4 Go to [System]-[System]-[Advanced] configure WAN Optimization listening port, default is , If Device is WANO Server, go to [System]-[Object], define IP group and application for server that need to be accelerating. Go to [WAN Optimization]-[Server], define acceleration policy, policy group & acceleration user. Configure WCCP or PBR for destination IP is peer devive network route to WANO as a gateway. 6,If Device is WANO Client, go to [WAN Optimization]-[Client], click NEW, configure peer device name, Username, Password, Peer IP Address (If peer device is double arm too then need to fill working IP), Listening Port, Transfer Protocol. Configure WCCP or PBR for destination IP is peer devive network route to WANO as a gateway. 7, Click on [Status] to check acceleration status. 8, Test Acceleration effect. Emergency handling practices If after deploy, network having problem and we can t locate the problem in 5 minutes of time then we have to disable WAN Optimization and see. If the issue still persist then we need to hardware bypass. After Deployment Round-off Work Standard Job Equipment checks Description 1: Verify all function is operating normally, working LED are operating properly. Make sure cable is plugged in tightly. 2: Backup configuration and submitted to the customer 3: Check label is marked correctly. 4: Verify device is operating properly after restart.

24 Environmental clean-up Change Admin password Clean up garbage left behind, try to restore the customer's original environment. After the installation was complete box collated on the customer specified location. If it is Test equipment, please do not throw away packing box, in order to avoid equipment damage. After deploy make sure not using default admin password and after change admin password make sure have backup the configuration file in case password forgot can restore with current configuration) Frequently Faced Issues handling Sangfor VPN 1 Check Local Device: a Verify Local device can access internet normally. b Verify VPN version was same or not. 2 Verify connection between local and HQ: a Confirm HQ public IP is correct b Verify connection between HQ public IP 1st Exp:HQ Public IP is Tesing Way:telnet If unable to connect host means Local network can t connect with HQ public IP on port 4009, after verify local network was no problem, can t verify HQ network. 1 Access to web console check logs and VPN status 1) Check VPN connection status and logs..

25 4 Verify on routing configuration If VPN establish normally, but still can t access to server via VPN, you may verify on routing table on both device. WAN Optimization 1 Can t establish acceleration tunnel a Test from WANO Client can connect to port 5400 on LAN IP of WANO Server. b Verify VPN connection d Verify default gateway was correct e Verify peer IP address is LAN IP of peer device, make sure username & password was correct. 2 No Optimization Effect a Make sure acceleration tunnel connected b Confirm acceleration policy was correct( Try enable all IP and all application default policy) c Make sure Both site of WANO can communicate with Local Subnet d Make sure traffic pass through both WANO e Enable/Disabled SNAT option in acceleration policy f Verify server got limitation on per IP per connections or not g Verify got encryption or not 3 Optimization effect not obvious a Verfiy bandwidth enough for this application or not b Verify WANO can support this application or not. c Verify from logs, make sure byte cache was running with no error. d Try change VPN use UDP as transfer protocol or change WANO transfer protocol to HTP (UDP) e No packet loss network user High speed TCP as transfer protocol f Application like FTP, need accelerate all port instead of just port 21 g Bandwidth occupied by non-acceleration traffic h Make sure in between no other WAN Optimizer product i Make sure Internal network/sever no issue j Make sure in between no BM/QOS device 5 After enable WAN Optimization some server can t access a Try enable SNAT option in acceleration policy. b Make sure return packet traffic don t go to backup line and bypass WANO c Make sure server not in High CPU usage or out of memory

UTM Content Security Gateway CS-2001

UTM Content Security Gateway CS-2001 UTM Content Security Gateway CS-2001 Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Setup the UTM Content Security Gateway... 4 3. Hardware Installation... 5 4. Basic System Configuration...

More information

Barracuda Link Balancer

Barracuda Link Balancer Barracuda Networks Technical Documentation Barracuda Link Balancer Administrator s Guide Version 2.3 RECLAIM YOUR NETWORK Copyright Notice Copyright 2004-2011, Barracuda Networks www.barracuda.com v2.3-111215-01-1215

More information

NeoGate TG Series Installation Guide

NeoGate TG Series Installation Guide NeoGate TG Series Installation Guide Version: V1.0 Yeastar Technology Co., Ltd. Date: Oct. 7, 2013 http://www.yeastar.com 1/14 Contents NeoGate TG Series Installation Guide 1. PREPARATION BEFORE INSTALLATION...

More information

NeoGate TA410/810 User Manual

NeoGate TA410/810 User Manual NeoGate TA410/810 User Manual Version 1.1 Date: Sept. 2, 2014 Yeastar Information Technology Co. Ltd 1. Preparation before Installation... 4 2. Hardware Specifications... 6 2.1 Overview... 6 2.2 LED Indicators

More information

XL-PB350CA. EoC bridge slave. User manual

XL-PB350CA. EoC bridge slave. User manual XL-PB350CA EoC bridge slave User manual Content 1. Equipment Connection... 6 2. Set Accessed PC... 6 3.WIFI WEB Configuration... 8 3.1 Login WEB Interface... 8 3.2 WAN Configuration... 10 3.2.1 PPPO E

More information

RX3041. User's Manual

RX3041. User's Manual RX3041 User's Manual Table of Contents 1 Introduction... 2 1.1 Features and Benefits... 3 1.2 Package Contents... 3 1.3 Finding Your Way Around... 4 1.4 System Requirements... 6 1.5 Installation Instruction...

More information

VPN2S. Handbook VPN VPN2S. Default Login Details. Firmware V1.12(ABLN.0)b9 Edition 1, 5/ LAN Port IP Address

VPN2S. Handbook VPN VPN2S. Default Login Details. Firmware V1.12(ABLN.0)b9 Edition 1, 5/ LAN Port IP Address VPN2S VPN2S VPN Firmware V1.12(ABLN.0)b9 Edition 1, 5/2018 Handbook Default Login Details LAN Port IP Address https://192.168.1.1 User Name admin Password 1234 Copyright 2018 ZyXEL Communications Corporation

More information

Broadband Router DC-202. User's Guide

Broadband Router DC-202. User's Guide Broadband Router DC-202 User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Broadband Router Features... 1 Package Contents... 3 Physical Details...3 CHAPTER 2 INSTALLATION... 5 Requirements...

More information

N150 WiFi DSL Modem Router Essentials Edition. N300 WiFi DSL Modem Router Essentials Edition

N150 WiFi DSL Modem Router Essentials Edition. N300 WiFi DSL Modem Router Essentials Edition N150 WiFi DSL Modem Router Essentials Edition Model D500 N300 WiFi DSL Modem Router Essentials Edition Model D1500 User Manual May 2018 202-11390-02 350 East Plumeria Drive San Jose, CA 95134 USA Support

More information

Wireless LAN Device Series. ZW-2000-IA User Manual

Wireless LAN Device Series. ZW-2000-IA User Manual Wireless LAN Device Series WLAN Outdoor Bridge ZW-2000-IA User Manual Version. TABLE OF CONTENTS PREFACE...3 CH 1. ZW-2000 INSTALLATION...4 PACKING LIST...4 HARDWARE INSTALLATION...5 CH 2. FIRST TIME CONFIGURATION...8

More information

User Manual. Rev:

User Manual.   Rev: Default Login Details Login Address: www.mykasda.com Login Password: Set up by users Default Wi-Fi SSID: Kasda xxxx KW6516 (Printed on product label) Default Wi-Fi Password: 12345678 www.kasdanet.com Rev:

More information

Installation. ProSAFE Wireless Controller Model WC7500 and Model WC7600

Installation. ProSAFE Wireless Controller Model WC7500 and Model WC7600 Installation ProSAFE Wireless Controller Model WC7500 and Model WC7600 Hardware Overview Before you install your wireless controller, familiarize yourself with its LEDs, buttons, and ports. Digital access

More information

Configuration Guide. For Managing EAPs via EAP Controller

Configuration Guide. For Managing EAPs via EAP Controller Guide For Managing EAPs via EAP Controller 1910012313 REV1.0.0 December 2017 CONTENTS 1 Overview... 1 2 Configuration... 2 2.1 Managing EAPs in the Same Subnet... 2 2.2 Managing EAPs in Different Subnets...

More information

SonicWALL Security Appliances. SonicWALL SSL-VPN 200 Getting Started Guide

SonicWALL Security Appliances. SonicWALL SSL-VPN 200 Getting Started Guide SonicWALL Security Appliances SonicWALL SSL-VPN 200 Getting Started Guide SonicWALL SSL-VPN 200 Appliance Getting Started Guide This Getting Started Guide contains installation procedures and configuration

More information

MANUAL NWAC7000. Wireless Management Platform

MANUAL NWAC7000. Wireless Management Platform MANUAL NWAC7000 Wireless Management Platform Contents Chapter 1 Manual Introduction... 4 Chapter 2:Product Introduction... 4 2.1 Products description... 4 2.2 Products Properties... 4 2.2.1Hardware Property...

More information

Installation and Configuration Quick Guide R3000. Industrial Dual SIM Cellular VPN Router 2 Eth + 1 RS RS USB Host.

Installation and Configuration Quick Guide R3000. Industrial Dual SIM Cellular VPN Router 2 Eth + 1 RS RS USB Host. Package Contents Installation and Configuration Quick Guide Before installing your R3000 Router, verify the kit contents as following. 1 x Robustel R3000 Industrial Dual SIM Cellular VPN Router (GPS/WiFi

More information

Configuration Guide TL-ER5120/TL-ER6020/TL-ER REV3.0.0

Configuration Guide TL-ER5120/TL-ER6020/TL-ER REV3.0.0 Configuration Guide TL-ER5120/TL-ER6020/TL-ER6120 1910012186 REV3.0.0 June 2017 CONTENTS About This Guide Intended Readers... 1 Conventions... 1 More Information... 1 Viewing Status Information... 2 System

More information

Installation and Configuration Quick Guide

Installation and Configuration Quick Guide Installation and Configuration Quick Guide R2000--Industrial Cellular VPN Router This document is written for the user which in order to let the user more easily install the router and also know the way

More information

Example - Configuring a Site-to-Site IPsec VPN Tunnel

Example - Configuring a Site-to-Site IPsec VPN Tunnel Example - Configuring a Site-to-Site IPsec VPN Tunnel To configure a Site-to-Site VPN connection between two Barracuda NextGen X-Series Firewalls, in which one unit (Location 1) has a dynamic Internet

More information

Security SSID Selection: Broadcast SSID:

Security SSID Selection: Broadcast SSID: 69 Security SSID Selection: Broadcast SSID: WMM: Encryption: Select the SSID that the security settings will apply to. If Disabled, then the device will not be broadcasting the SSID. Therefore it will

More information

CLEAR MODEM (SERIES G) USER GUIDE

CLEAR MODEM (SERIES G) USER GUIDE CLEAR MODEM (SERIES G) USER GUIDE GET TO KNOW YOUR CLEAR MODEM (SERIES G) 3 WHAT S IN THE BOX? 3 INFORMATIVE LED INDICATORS 3 USE WITH CARE 3 SET UP THE MODEM 4 PLACE THE MODEM ON A FLAT, STABLE SURFACE

More information

FD111HZ-EPON User Manual. Version:V1.1

FD111HZ-EPON User Manual. Version:V1.1 FD111HZ-EPON User Manual Version:V1.1 Contents 1 Attention... 2 1.1 Install Caution... 2 1.2 Precautions For Use... 2 2 Introduce... 3 2.1 Feature... 4 2.2 Environmental Parameter... 4 2.3 Interface...

More information

UIP1869V User Interface Guide

UIP1869V User Interface Guide UIP1869V User Interface Guide (Firmware version 0.1.8 and later) Table of Contents Opening the UIP1869V's Configuration Utility... 3 Connecting to Your Broadband Modem... 5 Setting up with DHCP... 5 Updating

More information

Unified Office Gateway UMG Quick Installation Guide. Version: 1.0

Unified Office Gateway UMG Quick Installation Guide. Version: 1.0 Unified ice Gateway UMG-2000 Quick Installation Guide Version: 1.0 Table of Contents 1. Package Contents... 3 2. Overview... 4 3. Hardware Installation... 6 3.1 Unpack the UMG-2000... 6 3.2 Choosing a

More information

Installation and Configuration Quick Guide R2000. Industrial Dual SIM Cellular VPN Router (2 Eth + 2 SIM) Package Contents

Installation and Configuration Quick Guide R2000. Industrial Dual SIM Cellular VPN Router (2 Eth + 2 SIM) Package Contents Package Contents Before installing your R2000 Router, please verify the kit contents as following. 1 x Robustel R2000 Industrial Dual SIM Cellular VPN Router 1 x 3-pin 3.5 mm male terminal block for power

More information

UTM Content Security Gigabit Gateway CS-950

UTM Content Security Gigabit Gateway CS-950 UTM Content Security Gigabit Gateway CS-950 Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Hardware Introduction... 4 2.1 Hardware Interface... 4 2.2 Hardware Installation... 6

More information

Wireless-G Router User s Guide

Wireless-G Router User s Guide Wireless-G Router User s Guide 1 Table of Contents Chapter 1: Introduction Installing Your Router System Requirements Installation Instructions Chapter 2: Preparing Your Network Preparing Your Network

More information

TA Series Analog VoIP Gateway Installation Guide

TA Series Analog VoIP Gateway Installation Guide TA Series Analog VoIP Gateway Installation Guide Version 1.5 Date: November 17, 2016 Yeastar Information Technology Co. Ltd. Contents About TA Series Analog VoIP Gateway... 3 1. Preparation before Installation...

More information

Table of Contents. CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line. Quick Installation Guide. CRA-200 Quick Installation Guide

Table of Contents. CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line. Quick Installation Guide. CRA-200 Quick Installation Guide CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line Quick Installation Guide Table of Contents VoIP ATA Package Contents... 2 Checklist... 2 IMPORTANT SAFETY INSTRUCTIONS... 3 Connecting

More information

Gigabit SSL VPN Security Router

Gigabit SSL VPN Security Router As Internet becomes essential for business, the crucial solution to prevent your Internet connection from failure is to have more than one connection. PLANET is the ideal to help the SMBs increase the

More information

A specific IP with specific Ports and Protocols uses a dedicated WAN (Load Balance Policy).

A specific IP with specific Ports and Protocols uses a dedicated WAN (Load Balance Policy). 21. Multiple WAN Vigor 3300Bplus has three WAN interfaces, while Vigor 3300 and Vigor 3300V both have four WAN interfaces. With the Load Balance feature, you can use multiple WAN links simultaneously.

More information

JT4100P LTE Outdoor CPE Administrator User Manual V1.0

JT4100P LTE Outdoor CPE Administrator User Manual V1.0 JT4100P LTE Outdoor CPE Administrator User Manual V1.0 Page 1 PLEASE READ THESE SAFETY PRECAUTIONS! RF Energy Health Hazard The radio equipment described in this guide uses radio frequency transmitters.

More information

User Guide TL-R470T+/TL-R480T REV9.0.2

User Guide TL-R470T+/TL-R480T REV9.0.2 User Guide TL-R470T+/TL-R480T+ 1910012468 REV9.0.2 September 2018 CONTENTS About This Guide Intended Readers... 1 Conventions... 1 More Information... 1 Accessing the Router Overview... 3 Web Interface

More information

Gigabit SSL VPN Security Router SG-4800

Gigabit SSL VPN Security Router SG-4800 Gigabit SSL VPN Security Router SG-4800 Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Hardware Installation... 4 2.1 Safety Instruction... 4 2.2 Front panel... 4 2.3 LED & Button

More information

Hardened Web-Smart High Power PoE Ethernet Switch

Hardened Web-Smart High Power PoE Ethernet Switch Quick Start Guide This quick start guide describes how to install and use the Hardened Web-Smart High Power PoE (Power over Ethernet) Ethernet Switch. This is the switch of choice for harsh environments

More information

AplombTech Smart Router Manual

AplombTech Smart Router Manual AplombTech Smart Router Manual (Version: 1.0) 1 Version & Purpose Version Manual version V 1.0 Explanation Corresponds to the initial version of device Purpose This manual describes the function features

More information

LevelOne GES GE with 1 Combo SFP Web Smart Switch User Manual

LevelOne GES GE with 1 Combo SFP Web Smart Switch User Manual LevelOne GES-0852 8 GE with 1 Combo SFP Web Smart Switch User Manual Version 1.0-1109 1 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device,

More information

F3123 GPRS ROUTER USER MANUAL

F3123 GPRS ROUTER USER MANUAL F3123 GPRS ROUTER USER MANUAL Add:J1-J2,3rd Floor,No.44,GuanRi Road,SoftWare Park,XiaMen,China 1 Zip Code:361008 Contents Chapter 1 Brief Introduction of Product... 3 1.1 General... 3 1.2 Product Features...

More information

N412 Installation Guide

N412 Installation Guide N412 Installation Guide Version 1.0 Date: March 29, 2016 Yeastar Information Technology Co. Ltd. i Contents About N412...1 1. Preparation before Installation...2 1.1 Packing List...2 1.2 Specifications

More information

Yamaha Router Configuration Training ~ Web GUI ~

Yamaha Router Configuration Training ~ Web GUI ~ Yamaha Router Configuration Training ~ Web GUI ~ Equipment RTX810 Gigabit VPN Router SWX2200-8G/24G Smart L2 Switch GbE 5, USB 3G modem 1Gbps throughput All GbE Cooperation with RTX810 200Mbps VPN throughput

More information

Broadband Router DC 202

Broadband Router DC 202 Broadband Router DC 202 Full Manual Table of Contents DC-202 xdsl/cable Broadband router REQUIREMENTS...4 INTRODUCTION...4 DC-202 Features...4 Internet Access Features...4 Advanced Internet Functions...5

More information

LKR Port Broadband Router. User's Manual. Revision C

LKR Port Broadband Router. User's Manual. Revision C LKR-604 4-Port Broadband Router User's Manual Revision C 1 Contents 1 Introduction... 4 1.1 Features... 4 1.2 Package Contents... 4 1.3 Finding Your Way Around... 5 1.3.1 Front Panel... 5 1.3.2 Rear Panel

More information

User Manual. AC ac Wireless Access Point/Router. Model WAC124. NETGEAR, Inc.

User Manual. AC ac Wireless Access Point/Router. Model WAC124. NETGEAR, Inc. AC2000 802.11ac Wireless Access Point/Router Model WAC124 December 2018 202-11885-02 NETGEAR, Inc. 350 E. Plumeria Drive San Jose, CA 95134, USA AC2000 802.11ac Support Thank you for purchasing this NETGEAR

More information

TEW-211BRP. Wireless AP Router. User s Manual

TEW-211BRP. Wireless AP Router. User s Manual TEW-211BRP Wireless AP Router User s Manual Version 1.4 - Jan 2002 CONTENTS Introduction...3 Hardware Installation...5 General Wireless AP Router System Connection...6 Wireless AP Router Default Settings

More information

Note: Because of the major firmware structure change, please make sure to press the reset button for more

Note: Because of the major firmware structure change, please make sure to press the reset button for more WMU-9000VPN Firmware Upgrade Guide Note: Because of the major firmware structure change, please make sure to press the reset button for more than 5 seconds before and after the firmware upgrade (before

More information

F5 WANJet 200. Quick Start Guide. Quick Start Overview

F5 WANJet 200. Quick Start Guide. Quick Start Overview F5 WANJet 200 Quick Start Guide Quick Start Overview Following is a high level overview of the steps required to successfully install and configure your F5 WANJet 200 appliance. For detailed instructions

More information

DC-228. ADSL2+ Modem/Router. User Manual. -Annex A- Version: 1.0

DC-228. ADSL2+ Modem/Router. User Manual. -Annex A- Version: 1.0 DC-228 ADSL2+ Modem/Router -Annex A- User Manual Version: 1.0 TABLE OF CONTENTS 1 PACKAGE CONTENTS...3 2 PRODUCT LAYOUT...4 3 NETWORK + SYSTEM REQUIREMENTS...6 4 DC-228 PLACEMENT...6 5 SETUP LAN, WAN...7

More information

R520 Quick Setup Guide

R520 Quick Setup Guide R520 Quick Setup Guide FCC ID: 2AQ5T-R520 1. Introduction Thanks for purchasing R520 broadband router. This router, equipped with the latest 4G and Wireless-N technology, is a full function network equipment.

More information

Yealink VCS Network Deployment Solution

Yealink VCS Network Deployment Solution Yealink VCS Network Deployment Solution Oct. 2015 V10.6 Yealink Network Deployment Solution Table of Contents Table of Contents... iii Network Requirements... 1 Bandwidth Requirements... 1 Calculating

More information

Chapter1: Overview. 1.1 Product Description. 1.2Application Chart. Model:-FS-2LAN+1POTS+WiFi Dual Mode. HGU User Manual V1.0

Chapter1: Overview. 1.1 Product Description. 1.2Application Chart. Model:-FS-2LAN+1POTS+WiFi Dual Mode. HGU User Manual V1.0 Chapter1: Overview 1.1 Product Description Thanks for choosing the 2LAN+1POTS+WiFi Home Gateway Unit. The terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network

More information

Smart Machine Smart Decision. R700_User Guide_V1.05 1

Smart Machine Smart Decision. R700_User Guide_V1.05 1 R700_User Guide_V1.05 R700_User Guide_V1.05 1 Document Title R700_User Guide Version 1.05 Date Status Document Control ID Released R700_User Guide_V1.05 General Notes SIMCom offers this information as

More information

F.A.Q for TW100-S4W1CA

F.A.Q for TW100-S4W1CA F.A.Q for TW100-S4W1CA Q: How do I configure the TW100-S4W1CA for a DSL, PPPoE connection? A: Step 1 Open your web browser and type the IP address of the TW100-S4W1CA in the address bar. The default IP

More information

DTX SERIES. DTX RG 301W Operations Manual (Software Release 3.0)

DTX SERIES. DTX RG 301W Operations Manual (Software Release 3.0) DTX RG 301W Operations Manual (Software Release 3.0) DTX SERIES 2010 Federal Signal Corporation 2645 Federal Signal Drive, University Park, IL 60484 3167 708 534 3400 255395A REV. A 1010 Printed in U.S.A.

More information

User Guide. 450Mbps/300Mbps Wireless N Access Point TL-WA901ND/TL-WA801ND REV

User Guide. 450Mbps/300Mbps Wireless N Access Point TL-WA901ND/TL-WA801ND REV User Guide 450Mbps/300Mbps Wireless N Access Point TL-WA901ND/TL-WA801ND REV4.0.0 1910011930 Contents About This Guide...1 Chapter 1. Get to Know About Your Access Point.................... 2 1. 1. Product

More information

300M Wireless-N Broadband Router User Manual

300M Wireless-N Broadband Router User Manual 300M Wireless-N Broadband Router Model No.: ib-wrb314n User Manual Ver.: 1.0.0 Contents...Error! Bookmark not defined. Chapter 1 Product Overview... 3 Package Contents 3 Conventions....4 Panel Overview...

More information

High Speed. Internet BroadBand Router. User Guide

High Speed. Internet BroadBand Router. User Guide High Speed Internet BroadBand Router User Guide FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

More information

Installation and Configuration Guide

Installation and Configuration Guide CYBERSECURITY, EVOLVED EdgeWave iprism Web Security Installation and Configuration Guide V8.0 15333 Avenue of Science, Suite 100 San Diego, CA 92128 Give us a call 1-855-881-2004 Send us an email: info@edgewave.com

More information

Peplink Balance Multi-WAN Routers

Peplink Balance Multi-WAN Routers Peplink Balance Multi-WAN Routers Model 20/30/210/310/380/390/580/710/1350 User Manual Firmware 5.1 September 10 Copyright & Trademarks Specifications are subject to change without prior notice. Copyright

More information

Gigaset Router / en / A31008-E105-B / cover_front_router.fm / s Be inspired

Gigaset Router / en / A31008-E105-B / cover_front_router.fm / s Be inspired s Be inspired Table of Contents Table of Contents Safety precautions........................... 3 The Gigaset Router........................... 3 Features and Benefits..................................................

More information

BiPAC 8501 R3/ 8521 R3

BiPAC 8501 R3/ 8521 R3 BiPAC 8501 R3/ 851 R3 SHDSL.bis Firewall Bridge/ Router Quick Start Guide Quick Start Guide Billion BiPAC 8501 R3/ 851 R3 SHDSL.bis Firewall Bridge/Router For more detailed instructions on configuring

More information

Dual WAN VPN Firewall VPN 3000 User s Guide. Version 1.0 Date : 1 July 2005 Please check for the latest version

Dual WAN VPN Firewall VPN 3000 User s Guide. Version 1.0 Date : 1 July 2005 Please check  for the latest version Dual WAN VPN Firewall VPN 3000 User s Guide Version 1.0 Date : 1 July 2005 Please check www.basewall.com for the latest version Basewall 2005 TABLE OF CONTENTS 1: INTRODUCTION... 4 Internet Features...

More information

CE APPROVED.4 INTRODUCTION.5 PACKAGE CONTENTS. 6 PRE - INSTALLATION CHECKLIST. 6 SYSTEM REQUIREMENTS. 6 FEATURES AND BENEFITS.11 SETUP WIZARD.

CE APPROVED.4 INTRODUCTION.5 PACKAGE CONTENTS. 6 PRE - INSTALLATION CHECKLIST. 6 SYSTEM REQUIREMENTS. 6 FEATURES AND BENEFITS.11 SETUP WIZARD. Web Edition Dec. 2002 Contents CE APPROVED...4 INTRODUCTION...5 PACKAGE CONTENTS... 6 PRE - INSTALLATION CHECKLIST... 6 SYSTEM REQUIREMENTS... 6 FEATURES AND BENEFITS... 7 4 - PORT CABLE/XDSL ROUTER...9

More information

On the left hand side of the screen, click on Setup Wizard and go through the Wizard.

On the left hand side of the screen, click on Setup Wizard and go through the Wizard. Q: How do I configure the TEW-435/504BRM (b1) to a DSL, PPPoE connection? A: Step 1 Open your web browser and type the IP address of the TEW-435/504BRM in the address bar. The default IP address is 192.168.0.1.

More information

CHAPTER 7 ADVANCED ADMINISTRATION PC

CHAPTER 7 ADVANCED ADMINISTRATION PC ii Table of Contents CHAPTER 1 INTRODUCTION... 1 Broadband ADSL Router Features... 1 Package Contents... 3 Physical Details... 4 CHAPTER 2 INSTALLATION... 6 Requirements... 6 Procedure... 6 CHAPTER 3 SETUP...

More information

FX Series Quick Start Guide - Version 6.0 Rev 1

FX Series Quick Start Guide - Version 6.0 Rev 1 This Quick Start Guide provides the 1.1 Unpacking 1.1.1 Packing List Inspect shipping containers for damage. If shipping containers are damaged, keep them until the contents of the shipment have been carefully

More information

How to open ports in the DSL router firmware version 2.xx and above

How to open ports in the DSL router firmware version 2.xx and above How to open ports in the DSL router firmware version 2.xx and above This example shows how to open port 3389 (which is used by Remote Desktop service) in the DSL router running firmware version 2.xx or

More information

AirCruiser G Wireless Router GN-BR01G

AirCruiser G Wireless Router GN-BR01G AirCruiser G Wireless Router GN-BR01G User s Guide i Contents Chapter 1 Introduction... 1 Overview...1 Features...1 Package Contents...2 AirCruiser G Wireless Router Rear Panel...2 AirCruiser G Wireless

More information

Quick Installation Guide

Quick Installation Guide Quick Installation Guide DL-200 Cellular Data logger V1.2_201610 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION... 4 1.1 CONTENTS LIST... 5 1.2 HARDWARE INSTALLATION... 6 1.2.1 WARNING... 6 1.2.2 SYSTEM REQUIREMENTS...

More information

Virtual Communications Express VCE over LTE User Guide

Virtual Communications Express VCE over LTE User Guide Version 1.17 Last Updated: May 2017 2017 Verizon. All Rights Reserved. The Verizon name and logo and all other names, logos, and slogans identifying Verizon s products and services are trademarks and service

More information

FWRIII-2105 SERIES. 4 ports 10/100Mbps RJ-45; built-in IEEE802.11n WiFi and 1 port 100Mbps SFP slot uplink Residential Gateway. Residential Gateway

FWRIII-2105 SERIES. 4 ports 10/100Mbps RJ-45; built-in IEEE802.11n WiFi and 1 port 100Mbps SFP slot uplink Residential Gateway. Residential Gateway FWRIII-2105 SERIES 4 ports 10/100Mbps RJ-45; built-in IEEE802.11n WiFi and 1 port 100Mbps SFP slot uplink Residential Gateway 4 ports 10/100Mbps RJ-45; built-in IEEE802.11n WiFi and 1 port 100Mbps SFP

More information

User Manual of RCS1~AP10

User Manual of RCS1~AP10 User Manual of RCS1~AP10 This manual is subject to tell users how to use this CAPWAP Broad Band Router with WLAN Controller and PoE Switch function, suit for those familiar with basic networking knowledge

More information

Content 1 OVERVIEW HARDWARE DESCRIPTION HARDWARE INSTALLATION PC CONFIGURATION GUIDE... 5 WEB-BASED MANAGEMENT GUIDE...

Content 1 OVERVIEW HARDWARE DESCRIPTION HARDWARE INSTALLATION PC CONFIGURATION GUIDE... 5 WEB-BASED MANAGEMENT GUIDE... Content 1 OVERVIEW...1 1.1FEATURES...1 1.2 PACKETCONTENTS...3 1.3 SYSTEM REQUIREMENTS... 1.4 FACTORY DEFAULTS...4 1.5 WARNINGS AND CAUTIONS...4 2 HARDWARE DESCRIPTION... 6 3 HARDWARE INSTALLATION...8 4

More information

APPLICATION NOTE AN0004 CHANGING THE IP ADDRESS ON AN EWSi PORTAL PLUS CONTROLLER WITH WINDOWS 7

APPLICATION NOTE AN0004 CHANGING THE IP ADDRESS ON AN EWSi PORTAL PLUS CONTROLLER WITH WINDOWS 7 INTRODUCTION Before installing an EWSi Portal Plus Controller on a network it is necessary to change the default IP address of the unit to one supplied by the network administrator. The following screen

More information

Version: V1.0. Yeastar Technology Co., Ltd. Date: 25 th, July, 2012

Version: V1.0. Yeastar Technology Co., Ltd. Date: 25 th, July, 2012 MyPBX U500 Installation Guide Version: V1.0 Yeastar Technology Co., Ltd Date: 25 th, July, 2012 http://www.yeastar.com 1/13 Contents MyPBX U500 Installation Guide 1. PREPARATION BEFORE INSTALLATION...

More information

The Administration Tab - Diagnostics

The Administration Tab - Diagnostics The Administration Tab - Diagnostics The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components. Ping Test. The Ping test will check the status of a connection.

More information

BEC 8920AC Ultimum The Ultimate Residential Gateway with ac VDSL2/ADSL2+/Bonded/FTTH Quick Start Guide

BEC 8920AC Ultimum The Ultimate Residential Gateway with ac VDSL2/ADSL2+/Bonded/FTTH Quick Start Guide BEC 8920AC Ultimum The Ultimate Residential Gateway with 802.11ac VDSL2/ADSL2+/Bonded/FTTH Quick Start Guide BEC 8920AC The Ultimate Residential Gateway w/ 802.11ac PLEASE READ THE QUICK START GUIDE AND

More information

SonicWALL TZ 150 Getting Started Guide

SonicWALL TZ 150 Getting Started Guide SonicWALL TZ 150 Getting Started Guide SonicWALL TZ 150 Security Appliance Getting Started Guide The SonicWALL TZ 150 is a total security platform delivering true layered security by integrating gateway

More information

Chapter 15: Advanced Networks

Chapter 15: Advanced Networks Chapter 15: Advanced Networks IT Essentials: PC Hardware and Software v4.1 1 Chapter 15 Objectives 15.1 Identify potential safety hazards and implement proper safety procedures related to networks 15.2

More information

1. Short description. 2. Features. 3. Technical parameters

1. Short description. 2. Features. 3. Technical parameters 1. Short description TCW122B-RR is a remote relay control module with embedded WEB server for set up. The device has two digital inputs and two relays, with normally open and normally closed contacts.

More information

AC1200 WiFi Router User Manual

AC1200 WiFi Router User Manual AC1200 WiFi Router User Manual Model R6120 September 2017 202-11753-03 350 E. Plumeria Drive San Jose, CA 95134 USA Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support

More information

Contents Summary... 3 Introduction... 5 User-define Terminal Parameters... 6 Fault Exclude... 14

Contents Summary... 3 Introduction... 5 User-define Terminal Parameters... 6 Fault Exclude... 14 Contents Summary... 3 Safety Precaution... 3 Product Introduction... 4 Interface Description... 4 Introduction... 5 Packing List... 5 Wiring... 5 User-define Terminal Parameters... 6 Login Webpage... 6

More information

WL5041 Router User Manual

WL5041 Router User Manual TECOM WL5041 Router User Manual TECOM CO., LTD. March 2003 2003 by TECOM CO., LTD. All rights reserved. Printed in Taiwan Table of contents Package Contents--------------------------------------- 2 Installing

More information

4-Ethernet Ports Router & WLAN (802.11n 1x1)ADSL2/2+

4-Ethernet Ports Router & WLAN (802.11n 1x1)ADSL2/2+ IFICATION PRODUCT: 4-Ethernet Ports Router & WLAN (802.11n 1x1)ADSL2/2+ MODEL NO: i1-4pwifi-01 Copyright by i1. All rights reserved. 1 Contents 1 PRODUCT OVERVIEW... 3 1.1 INTRODUCTION... 3 1.2 PRODUCT

More information

Gigabit Ethernet Switch. Quick Installation Guide MS400834M

Gigabit Ethernet Switch. Quick Installation Guide MS400834M Gigabit Ethernet Switch Quick Installation Guide MS400834M Version 1.0 Gigabit Ethernet Switch Quick Installation Guide II Table of Contents Table of Contents... ii 1. Introduction... 1 1.1 Overview...

More information

MARQUE: NETGEAR REFERENCE: R8000P-100EUS CODIC:

MARQUE: NETGEAR REFERENCE: R8000P-100EUS CODIC: MARQUE: NETGEAR REFERENCE: R8000P-100EUS CODIC: 4387546 NOTICE Nighthawk X6S AC4000 Tri-Band WiFi Router User Manual Model R8000P July 2017 202-11714-01 350 E. Plumeria Drive San Jose, CA 95134 USA Support

More information

4-Port Cable/DSL Router DX-E401. Product Name [French] Product Name [Spanish] USER GUIDE GUIDE DE L UTILISATEUR GUÍA DEL USUARIO

4-Port Cable/DSL Router DX-E401. Product Name [French] Product Name [Spanish] USER GUIDE GUIDE DE L UTILISATEUR GUÍA DEL USUARIO 4-Port Cable/DSL Router Product Name [French] Product Name [Spanish] DX-E401 USER GUIDE GUIDE DE L UTILISATEUR GUÍA DEL USUARIO 2 Introduction Dynex 4-Port Cable/DSL Router Introduction This router enables

More information

Table of Contents. Page ii

Table of Contents. Page ii Table of Contents Chapter 1 Introduction 1 Features... 1 Safety Instructions... 1 Package Contents... 2 Physical Details... 3 Chapter 2 Setup 5 Overview... 5 Using the Windows Wizard... 5 Chapter 3 Web-Based

More information

G806+H3C WSR realize VPN networking

G806+H3C WSR realize VPN networking G806+H3C WSR800-10 realize VPN networking File Version: V1.0.0 1 1.Configure H3C WSR 800-10 1.1.Enter H3C WSR 800-10 Web Server Power the H3C WSR 800-10 and connect PC Ethernet interface to H3C WSR 800-10

More information

Installation and Configuration Quick Guide. R3000 Quad. Industrial Cellular VPN Router with 4 Ethernet Ports (4 Eth + 1 RS-232/1 RS USB Host)

Installation and Configuration Quick Guide. R3000 Quad. Industrial Cellular VPN Router with 4 Ethernet Ports (4 Eth + 1 RS-232/1 RS USB Host) Package Contents Before installing your R3000 Quad Router, please verify the kit contents as following. 1 x Robustel GoRugged R3000 Quad Industrial Dual SIM Cellular VPN Router with 4 Ethernet Ports 1

More information

Contents. 2 NB750 Load Balancing Router User Guide YML817 Rev1

Contents. 2 NB750 Load Balancing Router User Guide YML817 Rev1 Contents CHAPTER 1. INTRODUCTION... 4 1.1 Overview... 4 1.2 Hardware... 6 1.2.1 Front Panel View... 6 1.2.2 Rear Panel View... 7 1.2.3 Hardware Load Default... 7 1.3 Features... 8 1.3.1 Software Feature...

More information

TZ 170 Quick Start Guide

TZ 170 Quick Start Guide COMPREHENSIVE INTERNET SECURITY S o n i c WALL Internet Security Ap p l i a n c e s TZ 170 Quick Start Guide Quick Start Installation Thank you for purchasing a SonicWALL Internet security appliance. The

More information

Quick Installation Guide DAP N300 Wi-Fi Range Extender

Quick Installation Guide DAP N300 Wi-Fi Range Extender N300 Wi-Fi Range Extender BEFORE YOU BEGIN Delivery Package Extender (brochure). If any of the items are missing, please contact your reseller. The User Manual and documents are available on D-Link website

More information

Deployment Guide: Routing Mode with No DMZ

Deployment Guide: Routing Mode with No DMZ Deployment Guide: Routing Mode with No DMZ March 15, 2007 Deployment and Task Overview Description Follow the tasks in this guide to deploy the appliance as a router-firewall device on your network with

More information

Hardware overview. Package contents MSM710, documentation, power supply, self-adhesive rubber feet.

Hardware overview. Package contents MSM710, documentation, power supply, self-adhesive rubber feet. In MSM710 Controller Quickstart This Quickstart applies to both the MSM710 Access Controller (J9328A) and the MSM710 Mobility Controller (J9325A). This Quickstart introduces the HP ProCurve Networking

More information

Installation and Configuration Quick Guide. R3000 Lite. Industrial Dual SIM Cellular VPN Router (1 Eth + 1 RS RS USB Host)

Installation and Configuration Quick Guide. R3000 Lite. Industrial Dual SIM Cellular VPN Router (1 Eth + 1 RS RS USB Host) Package Contents Before installing your R3000 Lite Router, please verify the kit contents as following. 1 x Robustel R3000 Lite Industrial Dual SIM Cellular VPN Router 1 x 3-pin pluggable terminal block

More information

Manual of Wireless Access Point

Manual of Wireless Access Point Manual of Wireless Access Point This is the manual of outdoor CPE, which will approximate guide you how to set and apply the outdoor CPE, it provide a convenient graphical interface for network construction

More information

User Manual. Nighthawk AC2400 Smart WiFi Router. Model AC2400. NETGEAR, Inc.

User Manual. Nighthawk AC2400 Smart WiFi Router. Model AC2400. NETGEAR, Inc. Nighthawk AC2400 Smart WiFi Router Model AC2400 December 2018 202-11909-02 NETGEAR, Inc. 350 E. Plumeria Drive San Jose, CA 95134, USA Nighthawk AC2400 Smart WiFi Router Support Thank you for purchasing

More information

Citrix CloudBridge CB User Manual

Citrix CloudBridge CB User Manual Citrix CloudBridge CB 504-2 User Manual 1 P a g e Chapter 1 CloudBridge Hardware Platform Topics: Citrix CloudBridge CB 504-2 Summary of Hardware Specifications The Citrix CloudBridge CB 504-2 hardware

More information

WISNETWORKS. WisOS 11ac V /3/21. Software version WisOS 11ac

WISNETWORKS. WisOS 11ac V /3/21. Software version WisOS 11ac WISNETWORKS User Manual V1.1 2016/3/21 Software version 1.0.0021 Table of contents 1. Setup& WMI... 3 1.1 Hardware Setup... 3 1.2 Web Management Interface... 3 2. Status... 4 2.1 Overview... 4 2.1.1 System...

More information

Viewing System Status, page 404. Backing Up and Restoring a Configuration, page 416. Managing Certificates for Authentication, page 418

Viewing System Status, page 404. Backing Up and Restoring a Configuration, page 416. Managing Certificates for Authentication, page 418 This chapter describes how to maintain the configuration and firmware, reboot or reset the security appliance, manage the security license and digital certificates, and configure other features to help

More information