BigIron Patch Release v

Transcription

1 Software Requirements for v The tables below list the boot and flash images required for proper operation of this patch release. BigIron 4000, 8000, JetCore M2B07605.bin or Layer 2 Switch code: IronCore M4 M2B07605.bin or Layer 2 Switch code: IronCore VM1 M2B07605.bin (all MP images) VSB07100.bin (VSM code) Layer 2 Switch MP code: VM1S08001v.bin Layer 3 Switch IP-only MP code: VM1R08001v.bin VSP code: VSP08001v.bin 2007 Foundry Networks, Inc. 3/19/2010 1

2 NetIron 400, 800, 1500 Module Boot Image Flash Image JetCore M2B07605.bin or Service Provider IP-only Layer 3 Switch code: N2P08000.bin IronCore M4 M2B07605.bin or Service Provider IP-only Layer 3 Switch code N2P08001v.bin IronCore VM1 MP code: M2B07605.bin or VSP code: VSP08001v.bin FastIron 4802 VSM code: VSB07100.bin or N/A M2B07605.bin or Layer 2 Switch code: 2010 Brocade Communications Systems, Inc. 3/19/2010 2

3 FastIron II, II PLUS, III IronCore M4 modules: M2B07605.bin or Layer 2 Switch code: FastIron 400, 800, and 1500 JetCore modules M2B07605.bin or Layer 2 Switch code: 2010 Brocade Communications Systems, Inc. 3/19/2010 3

4 Others Modules Boot Image Flash Image 10 Gigabit Ethernet modules The Gigabit Ethernet modules do not have boot code separate from the management module. However, they do have Field- Programmable Gate Arrays (FPGAs). See the next column. ATM modules P2B06000.bin A2R08001v.bin POS modules P2B06000.bin Note: This boot code applies to NPA OC- 48 modules and to standard POS modules (OC-3, OC- 12, and OC-48). The modules do not have flash code separate from the management module. However, they do have Field- Programmable Gate Arrays (FPGAs). B10Gx-ER, B10Gx-LR, and B10Gx-SR only (FPGA version numbers): - rxbmgr.bin version 80, revision 6 - -rxpp.bin version 81, revision 16 - txaccum.bin version 82, revision 6 - txpp.bin version 83, revision 13 - ageram.bin version 84, revision 4 1-port and 2-port 10-Gigabit Ethernet modules with XENPAK optics only (FPGA version numbers): - xpp.bin version 88, revision 54 - xtm.bin version 89, revision 43 Note: To determine the versions that are running on the modules, enter the show flash command. The version information is listed separately for each 10 Gigabit Ethernet module in the chassis. Layer 3 code for NPA OC-48 model N2P2488-A modules L3P08001v.bin Layer 2 code for NPA OC-48 model N2P2488-A modules: L2P08001v.bin Layer 2 and Layer 3 code for OC-3 and OC-12 POS modules: P2R08001v.bin Note: The NPA OC-48 POS modules are supported only in a NetIron Internet Backbone router running B2P07208.bin or N2P07208.bin or higher Brocade Communications Systems, Inc. 3/19/2010 4

5 Software Fixes in v The following table lists the software issues that were fixed in release v. The P column indicates the priority of the software fix, as follows: 0 = Critical 1 = Major 2 = Medium 3 = Minor Category P Description Bug ID # BGP 1 Module: N/A Symptom: In a Router configured with BGP, the log changes the IP address of the BGP peer when removing a BGP from the configuration FDP 1 Module: N/A Symptom: In a Switch/Router configured with FDP, the FDP packets cannot be sent over a 10G tagged port FDP 1 Module: N/A Symptom: In a Switch/Router configured with Trunking, the FDP configuration on secondary of the trunk group can be removed using the no fdp enable command HTTP Agent 1 Module: N/A Symptom: In a Switch/Router, accessing HTTP Cookie Request Header can cause a system reset IPv6 Tunnel 1 Module: N/A Symptom: In a Router configured with IPv6 Tunnels, the port name is not saved in the tunnel interface configuration IPv6 Tunnel 1 Module: N/A Symptom: Configuring an IPv4 address on an IPv6 IP tunnel interface can cause a system reset Brocade Communications Systems, Inc. 3/19/2010 5

6 Category P Description Bug ID # SNTP 1 Module: N/A Symptom: In a Switch/Router configured with SNTP, the status of the second SNTP server is not correctly updated when it goes down , System 1 Module: 10G Symptom: In a Switch/Router, the configuration of the qd-portx10g causes complete packet drops System 1 Module: N/A Symptom: In a Router, configuring of the jumbo MTU using default-mtu command can sometimes cause a system reset System 1 Module: N/A Symptom: In a Switch/Router, sometimes inconsistent data structure can cause a system reset System 1 Module: N/A Symptom: In a Switch/Router, the copying of a port mask can sometimes cause a system reset Brocade Communications Systems, Inc. 3/19/2010 6