Internet Protocol Version 6 (IPv6)

Size: px
Start display at page:

Download "Internet Protocol Version 6 (IPv6)"

Transcription

1 This chapter provides information about Internet Protocol version 6 (IPv6), which is the latest version of the Internet Protocol (IP). Packets are used to exchange data, voice, and video traffic over dual-stack IP networks, and increase the number of network address bits from 32 bits in IPv4 to 128 bits. IPv6 support in the Cisco Unified Communications Manager network allows the network to behave transparently in a dual-stack environment and provides additional IP address space and autoconfiguration capabilities to devices that are connected to the network. Use this information in conjunction with the document, Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager, which provides design guidelines for deploying IPv6 in your Cisco Unified Communications network. Note For information about IPv6 support for your IP phone or Cisco Unity Connection, see the Cisco Unified IP Phone Administration Guide that supports your phone model or the Cisco Unity Connection documentation. Configure IPv6, page 1 IPv6 for Cisco Unified CM Feature, page 3 System Requirements for IPv6, page 14 Interactions and Restrictions, page 15 Install and Activate IPv6, page 19 IPv6 Configuration, page 19 Provide Information to Users, page 29 Troubleshooting IPv6, page 29 Configure IPv6 Internet Protocol version 6 (IPv6), which is the latest version of the Internet Protocol (IP) that uses packets to exchange data, voice, and video traffic over dual-stack IP networks, increases the number of network address bits from 32 bits in IPv4 to 128 bits. IPv6 support in the Cisco Unified Communications Manager OL

2 Configure IPv6 network allows the network to behave transparently in a dual-stack environment and provides additional IP address space. IPv6 also supports autoconfiguration capabilities for devices that are connected to the network. This section lists the high-level tasks that you must complete to configure IPv6. To complete these tasks, you will need to refer to the following Cisco Unified Communications Manager documentation, which contains detailed procedures and information about configuration parameters: Installing Cisco Unified Communications Manager Cisco Unified Communications Manager Administration Guide Cisco Unified Communications Manager Operating System Administration Guide Perform the following steps to configure IPv6 in your network. Before You Begin Before you configure IPv6, review all IPv6-related documentation. Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager Cisco IOS IPv6 Configuration Library Implementing VoIP for IPv6 This IPv6 chapter Procedure Step 1 Step 2 Step 3 Step 4 Step 5 Provision a local IPv6-capable DNS and DHCP server. Caution You can provision your DNS server for IPv6 prior to upgrading from an earlier release of Cisco Unified Communications Manager to the current release. However, do not configure the DNS records for Cisco Unified Communications Manager for IPv6 until after you upgrade to the current release. Configuring the DNS records for Cisco Unified Communications Manager for IPv6 prior to upgrading to the current release causes the upgrade to fail and causes your system to become nonfunctional after you reboot. Cisco recommends that the Cisco Unified Communications Manager node use a global address or a unique local address (ULA). If the Cisco Unified Communications Manager node obtains the IPv6 address from the DHCPv6 server or via stateless address autoconfiguration, ensure that the Cisco Unified Communications Manager node only obtains one global address or one unique local IPv6 address from the DHCPv6 server. If you manually assign the address, it will override any address obtained from the DHCPv6 server. Make sure that you have compatible network hardware and Cisco IOS software that is installed and configured; for example, configure your Integrated Services Router (ISR) G2 gateways and Cisco IOS MTP for IPv6. Install the current release of Cisco Unified Communications Manager. Before you install subsequent nodes (subscribers) in the cluster, add the IPv4 server information to the Server Configuration window in Cisco Unified Communications Manager Administration. Enable IPv6 in the Cisco Unified Communications Operating System and ensure that the Cisco Unified Communications Manager node obtains an IPv6 address. Cisco recommends that the Cisco Unified Communications Manager node use a static non-link-local IPv6 address. For each node in the cluster, perform these tasks. Performing these tasks requires a reboot of the node. In the Enterprise Parameters Configuration window in Cisco Unified Communications Manager Administration, choose True for the Enable IPv6 enterprise parameter. 2 OL

3 IPv6 for Cisco Unified CM Feature Step 6 Step 7 Step 8 After you update this enterprise parameter, restart the Cisco CallManager, Cisco IP Voice Media Streaming App, Cisco CTIManager, Cisco Certificate Authority Proxy Function, and the Cisco IPVMS services in Cisco Unified Serviceability. For the node that you are configuring in Cisco Unified Communications Manager Administration, choose System > Server and enter the unique local address or a host name that can resolve to a IPv6 address in the IPv6 Name field. For each node in the cluster, perform this task. If you enter a host name, remember to update the DNS server with the appropriate Cisco Unified Communications Manager name and address information. Caution You can provision your DNS server for IPv6 prior to upgrading to the current release. However, do not configure the DNS records for IPv6 for Cisco Unified Communications Manager until after you upgrade to the current release. Configuring the DNS records for IPv6 for Cisco Unified Communications Manager prior to upgrading to the current release causes the upgrade to fail and causes your system to become nonfunctional after you reboot. In Cisco Unified Communications Manager Administration, configure phone-related and SIP trunk-related IPv6 settings. For example, configure the IP Addressing Mode and Allow Auto-Configuration for Phones settings in the Common Phone Profile Configuration window; then, apply the common device profile configuration to the phone or SIP trunk. Restart the Cisco CallManager, Cisco IP Voice Media Streaming App, Cisco CTIManager, Cisco Certificate Authority Proxy Function and the Cisco IPVMS services in Cisco Unified Serviceability. Related Topics Media Termination Points, on page 10, on page 1 Cisco Unified CM, on page 4 Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window, on page 20 Configure Service and Enterprise Parameters for IPv6, on page 23 IPv6 for Cisco Unified CM Feature CTI Applications This section provides information about IPv6 for Cisco Unified CM. CTI provides IP address information through the JTAPI and TAPI interfaces, which can support IPv4 and IPv6 addresses. To support IPv6, applications need to use a JTAPI /TAPI client interface version that supports IPv6. Consider the following information for CTI applications and CTI port/route points: CTI applications connect to CTI Manager by using either an IPv4 or an IPv6 address. If you set the Enable IPv6 enterprise parameter to True in Cisco Unified Communications Manager Administration, CTI Manager can support CTI connections from applications that use IPv6 addresses. CTI applications can register CTI ports/route points that use IPv6 or IPv4 addresses. CTI applications that handle media events for CTI ports/route points can register devices with either a IPv4 or IPv6 address, depending on the configuration for the device. OL

4 Cisco Unified CM CTI applications can monitor/control CTI-supported devices that have IPv6 capability. If a call uses IPv6, IPv6 information, including CallingPartyAddress and media IP address, gets passed to the CTI application. Cisco Unified CM This section describes how Cisco Unified Communications Manager supports devices that use IPv4, IPv6, or IPv4 and IPv6. In addition, this section describes how Cisco Unified Communications Manager runs in dual-stack mode, how Cisco Unified Communications Manager can process calls for IPv4 and IPv6 devices, and how Cisco Unified Communications Manager can reserve and allocate bandwidth for IPv4 and IPv6 calls. This document uses the terminology, dual stack (or dual-stack mode), which assumes that the device or server uses both an IPv4 and an IPv6 address. Cisco Unified Communications Manager Server Cisco Unified Communications Manager can interact with and support devices that use IPv6 only, but you cannot configure the Cisco Unified Communications Manager server as IPv6 only because Cisco Unified Communications Manager must interact with and support devices/features that support IPv4 only (or both IPv4 and IPv6). For Cisco Unified Communications Manager to support devices that use IPv6, including dual-stack devices, which can provide both IPv4 and IPv6 addresses, you must configure Cisco Unified Communications Manager, so it runs in dual-stack mode; that is, you must ensure that the Cisco Unified Communications Manager server has both an IPv4 address and an IPv6 address that is configured for it, so it can interact and support devices that use IPv4 only, IPv6 only, or both IPv4 and IPv6. Intracluster Cisco Unified Communications Manager node-to-node communication uses IPv4. Before the Cisco Unified Communications Manager server can run in dual-stack mode, you must perform the following tasks: Call Processing By running in dual-stack mode, Cisco Unified Communications Manager can set up calls under the following circumstances: When all devices support IPv4 only. When all devices support IPv6 only. When all devices run in dual-stack mode, in which case, Cisco Unified Communications Manager uses the configuration for the IP Addressing Mode Preference for Signaling setting for signaling events and the IP Addressing Mode Preference for Media enterprise parameter for media events. When one device supports IPv4 and another device supports IPv6, in which case, Cisco Unified Communications Manager attempts to insert into the call an MTP that can translate IPv4 to IPv6. 4 OL

5 Cisco Unified CM Even if your device can support multiple IPv6 addresses, Cisco Unified Communications Manager only handles one IPv6 address. In addition, if your device supports an IPv4 and IPv6 address, Cisco Unified Communications Manager can simultaneously handle both addresses. Call Admission Control (CAC) Because using IPv6 requires 20 more bytes of data in its header than IPv4, an IPv6 call requires more bandwidth than a similar IPv4 call that uses the same codec/media payload type. For example, a G.711 call that uses IPv4 uses 80 kb/s of bandwidth; whereas, a G.711 call that uses IPv6 uses 88 kb/s of bandwidth. To reserve and adjust location-based bandwidth for a call that uses IPv6, Cisco Unified Communications Manager can calculate the bandwidth that is needed for an IPv6 call for all codecs that are supported with Cisco Unified Communications Manager. After the device contacts Cisco Unified Communications Manager for bandwidth reservation during the call setup, Cisco Unified Communications Manager identifies the IP version; if the call uses IPv6, Cisco Unified Communications Manager reserves the bandwidth for IPv6, and if the call uses IPv4, Cisco Unified Communications Manager reserves the bandwidth for IPv4. If Cisco Unified Communications Manager cannot identify the IP version that is used for the call, for example, the call terminates to a SIP trunk or the device supports both IP versions, Cisco Unified Communications Manager initially reserves bandwidth that supports IPv6 and later adjusts the bandwidth after media negotiation occurs. Cisco Unified Communications Manager reserves bandwidth for one call leg at a time, so, if an MTP is inserted into the call and location-based CAC is required, ensure that the MTP is colocated with one of the devices, so location-based CAC reserves the bandwidth across the WAN based on the side that is opposite of the MTP. For example, if a call occurs from an IPv4 to IPv6 device, which causes an insertion of the MTP on the IPv4 side, Cisco Unified Communications Manager reserves bandwidth across the WAN based on IPv6. Alternatively, if the MTP is inserted for the device that uses IPv6, Cisco Unified Communications Manager reserves bandwidth across the WAN based on IPv4. If you want to do so, you can configure the Call Counting CAC Enabled, Audio Bandwidth for Call Counting CAC, and the Video Bandwidth Unit for Call Counting CAC service parameters in Cisco Unified Communications Manager Administration, so the call uses a fixed bandwidth value instead of having Cisco Unified Communications Manager reserve and adjust bandwidth during the call. Be aware that configuring these service parameters can cause Cisco Unified Communications Manager to oversubscribe or undersubscribe bandwidth for the call. Procedure Step 1 Step 2 On the Cisco Unified Communications Manager server, enable IPv6 in the Cisco Unified Communications Operating System. Determine how the Cisco Unified Communications Manager server will get its IPv6 address, and ensure that the Cisco Unified Communications Manager server obtains its IPv6 address. In the Cisco Unified Communications Operating System, you can request a non-link-local address from the DHCPv6 server, configure a static non-link-local IPv6 address for the Cisco Unified Communications Manager server, or obtain an non-link-local IPv6 address via stateless address autoconfiguration. (Cisco recommends a static non-link-local IPv6 address for the server.) Ensure that the Cisco Unified Communications Manager server only obtains one non-link local IPv6 address. If the server obtains more than one IPv6 address, Cisco Unified Communications Manager may not behave as expected. OL

6 Cisco Unified IP Phones If the Cisco Unified Communications Manager server obtains an IPv6 address via stateless address autoconfiguration and you also have a static IPv6 address that is configured for the server, Cisco Unified Communications Manager ignores the IPv6 address that is obtained via stateless address autoconfiguration and uses the static address. Step 3 Step 4 For Cisco Unified Communications Manager, set the Enable IPv6 enterprise parameter to True, which ensures that Cisco Unified Communications Manager runs in dual-stack mode. Caution You must enable IPv6 in the Cisco Unified Communications Operating System and set the Enable IPv6 enterprise parameter to True. If you do not perform both of these tasks, the Cisco CallManager service runs in IPv4 and phones that you configure with an IP Addressing Mode of IPv6 Only cannot register with Cisco Unified Communications Manager. Caution After you perform these tasks on the server, you must restart the server for the changes to take effect. In Cisco Unified Communications Manager Administration, configure the Host Name/IP Address and IPv6 Name fields in the Server Configuration window, which ensures that Cisco Unified Communications Manager runs in dual-stack mode. Cisco Unified Communications Manager considers the Host Name/IP Address field mandatory; that is, you must configure this field even if devices in your network only support IPv6. If devices in your network support IPv6 only or IPv4 and IPv6, you must configure the IPv6 Name field in addition to the IP Address/Hostname field; be aware that you must enter the non-link local IPv6 address for the Cisco Unified Communications Manager in the IPv6 Name field. The phones use these fields, which are included in the TFTP configuration file, to retrieve the IP addresses of the Cisco Unified Communications Manager server, so phone registration occurs. Related Topics Cisco Unified CM, on page 4 Cisco Unified IP Phones, on page 6 Media Termination Points, on page 10 SIP Trunks, on page 12 Interactions and Restrictions, on page 15 Configure Service and Enterprise Parameters for IPv6, on page 23 Cisco Unified IP Phones This section describes use cases for IPv4 and IPv6 calls between the phone and Cisco Unified Communications Manager. This section does not describe how the phone gets its IP address and other network settings. For additional information on using IPv6 with your phone, see the Cisco Unified IP Phone Administration Guide that supports your phone model and this release of Cisco Unified Communications Manager. The phone administration guide describes IPv6 settings that display on the phone. See the following use cases, which assume that Cisco Unified Communications Manager can listen on the correct port, that an MTP is available to translate IP address versions, and that the device has the correct address version. 6 OL

7 Cisco Unified IP Phones Every time that the phone boots up, it boots up in dual-stack mode; that is, it can support both IPv4 and IPv6. After the phone processes the configuration file from the TFTP server, the IP Addressing Mode from the Common Device Configuration window gets set on the phone. Based on the IP Addressing Mode, the phone may disable DHCP or DHCPv6 and may release addresses that do not support the IP Addressing Mode; for example, if the IP Addressing Mode is IPv6 Only, the phone releases the IPv4 address. If the phone has multiple, unique local or multiple global addresses, the first address that is assigned to the phone specifies the address that gets sent to Cisco Unified Communications Manager for signaling and media events. If a phone that runs in dual-stack mode loses a specific address type, the phone unregisters from Cisco Unified Communications Manager and reregisters with the remaining address type. For media negotiation, Cisco Unified Communications Manager dynamically determines the IP address to use for the call; that is, Cisco Unified Communications Manager identifies whether the devices share the IP Addressing Mode. For example, if one device has an IP Addressing Mode of IPv4 and IPv6 and the other device has an IP Addressing Mode of IPv4 Only, Cisco Unified Communications Manager uses IPv4 for the media negotiation and requires no MTP for translating IP address versions. If the devices on the call only support one IP address version and the versions are not compatible, Cisco Unified Communications Manager uses the IP address version of the device and tries to insert an MTP into the call that can translate IPv4 to IPv6. If all devices on the call support both IP address versions, Cisco Unified Communications Manager uses the configuration for the IP Addressing Mode Preference for Media enterprise parameter for the media negotiation. Phone Has IP Addressing Mode of IPv4 Only If the IP Addressing Mode for the phone is IPv4 Only, the phone connects to Cisco Unified Communications Manager by using an IPv4 address. Signaling and media negotiation occurs by using an IPv4 address. If an IPv4 address is not available for the phone, the user cannot make calls. Phone Has IP Addressing Mode of IPv6 Only If the IP Addressing Mode for the phone is IPv6 Only and you set the Enable IPv6 enterprise parameter to True, the phone uses a global scope or unique local scope IPv6 address to connect to Cisco Unified Communications Manager. Signaling and media negotiation occur by using this IPv6 address. If an IPv6 address is not available for the phone, the user cannot make calls. Likewise, if an IPv6 address is not configured for the phone, the phone cannot register with Cisco Unified Communications Manager. Cisco Unified Communications Manager does not support all features on phones where the IP Addressing Mode is IPv6 Only. For a list of features that are not supported, see the Interactions and Restrictions, on page 15. If you configure IPv6 Only as the IP Addressing Mode for phones that run SIP, the Cisco TFTP service overrides the IP Addressing Mode configuration and uses IPv4 Only in the configuration file. OL

8 DHCPv6 Phone Has IP Addressing Mode of IPv4 and IPv6 If the IP Addressing Mode for the phone is IPv4 and IPv6 (dual stack mode) and you set the Enable IPv6 enterprise parameter to True, Cisco Unified Communications Manager considers the IP address support for the phone and the configuration for IP Addressing Mode Preference for Signaling setting before connecting the call. If only one IP address version is available on the phone, the phone uses the address that is available to connect to Cisco Unified Communications Manager for signaling negotiation. If both IP addresses types are available on the phone, the phone uses the configuration for the IP Addressing Mode for Signaling setting for signaling negotiation. After you configure the phone in Cisco Unified Communications Manager Administration, you can view the IP address for the phone in the Find and List Phones window. For phones that have an IPv4 address only or both IPv4 and IPv6 addresses, the IPv4 address displays in the window. For phones with an IPv6 address only, the IP Address displays as in the IP Address column in the Find and List Phones window. To identify the IPv6 address for the phone, click the Device Name link in the Find and List Phones window, which causes the Phone Configuration window to display. For the IPv6 Only device, the Phone Configuration window displays an IPv4 address of , listed as IP Address, above the IPv6 address. In the Phone Configuration window for a specific phone, you can view the IPv4 address and the IPv6 address, if applicable, that the phone uses. For phones in dual-stack mode that have both an IPv4 and IPv6 address, you can click the IPv4 or IPv6 address in the Phone Configuration window, which points to an IPv4 URL for the web server on the phone. For phones that use an IPv6 address only, you cannot click the IPv6 address because the web server on the phone only supports IPv4. DHCPv6 DHCPv6, which is the version of Dynamic Host Configuration Protocol that supports IPv6, can assign an IPv6 address and other network settings to the phone after you connect it to the network. In addition, DHCPv6 can assign an IPv6 address to the Cisco Unified Communications Manager server; that is, if you do not plan to assign a static IP address to the server. (Cisco recommends that you assign a static IP address to the server.) Cisco Unified Communications Manager does not provide DHCPv6 server capabilities, so you must configure a DHCPv6 server in your network if you plan to use DHCPv6 to assign IPv6 network configuration settings to the phone or server. If you want to allow the phone to receive its IP address via DHCPv6 rather than stateless address autoconfiguration, make sure that you set the Allow Auto-Configuration for Phones setting to Off. For information on this setting, see the Access IPv6 and IPv4 Configuration in Unified CM Administration, on page 24. Note Because Cisco Network Registrar (CNR) 6.2 provides both DNS and DHCP support for IPv4 and IPv6, consider using Cisco Network Registrar for your DNS and DHCP support. For more information on this product, see the Cisco Network Registrar User's Guide, OL

9 DNS Note If you want to do so, you can configure a Cisco IOS router or switch as a DHCPv6 server; for example, you can configure a Cisco Catalyst 3560 Series Switch or a Cisco Catalyst 3750 Series Switch that runs 12.2(46)SE (or later) as a DHCPv6 server. Before you configure this router/switch, verify that your router/switch supports the Cisco vendor-specific DHCPv6 information options that are required for IPv6 and DHCPv6 support. Note For highest scope rules, consider configuring a DHCPv6 server, so it assigns only unique local addresses to the phone. If you must use global unicast addresses, configure a TLS connection and SRTP, as described in the Cisco Unified Communications Manager Security Guide. For additional information on DHCP, see the Cisco Unified Communications Manager System Guide, and Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager. DNS For IPv6, DNSv6 handles the AAAA record, which can map IPv6 addresses. For IPv4, DNS handles the A record, which can map IPv4 addresses. For IPv4 and IPv6, the following fields rely on DNS; that is, if you configure hostnames for the fields: Host Name/IP Address (Server Configuration window) - You can enter an IPv4 address or host name. IPv6 Name (Server Configuration window) - You can enter an IPv6 address or host name. Destination Address (SIP Trunk Configuration window) - You can enter a valid V4 dotted IP address, a fully qualified domain name (FQDN), or DNS SRV record if the SIP trunk is configured to use a DNS SRV port as a destination. Destination Address IPv6 (SIP Trunk Configuration window) - You can enter a valid IPv6 address (global unicast, unique local, or a hostname), a fully qualified domain name (FQDN), or a DNS SRV record if the SIP trunk is configured to use a DNS SRV port as a destination. Caution You can provision your DNS server for IPv6 prior to upgrading from Cisco Unified Communications Manager to the current release. However, do not configure the DNS records for Cisco Unified Communications Manager for IPv6 until after you complete the upgrade to the current release. If you configure the DNS records for Cisco Unified Communications Manager for IPv6 before you complete the upgrade, the upgrade can fail and cause your system to become nonfunctional after you reboot. Caution If the AAAA record or A record do not map correctly, calls may fail. OL

10 Gateways Note Because Cisco Network Registrar (CNR) 6.2 provides both DNS and DHCP support for IPv4 and IPv6, consider using CNR for your DNS and DHCP support. For more information on this product, see the Cisco Network Registrar User's Guide, 6.2. Gateways MGCP and H.323 gateways do not support devices that function in IPv6-only mode. To communicate with IPv6-only devices that connect to these gateways, Cisco Unified Communications Manager inserts an MTP that can translate IPv4 to IPv6 during a call. The Cisco ATA 186 and 188 Analog Telephone Adaptors do not support IPv6. Analog phone gateways can operate in IPv4 only, IPv6 only, or IPv4 and IPv6 (dual-stack mode). The following gateway models are supported for IPv6: MTP/Transcoder: ISR G2 29XX and 39XX SIP Gateways (hardware platform configuration): ISR G2 29XX and 39XX, AS5350XM, and AS5400XM SIP Gateways (number of ports that are supported): VG350, VG224, VG204XM, and VG202XM SCCP Analog Gateways: VG350, VG224, VG204XM, and VG202XM Cisco IOS SIP gateways can support IPv6 only, IPv4 only, or IPv4 and IPv6 simultaneously in dual-stack mode. Before Cisco Unified Communications Manager can interact with these gateways, you must configure it in the SIP Trunk Configuration window in Cisco Unified Communications Manager Administration. For Cisco Unified Communications Manager considerations for the gateway, review the SIP Trunks, on page 12 and the Media Termination Points, on page 10. In addition to configuring the gateway in Cisco Unified Communications Manager Administration, you must configure the gateway, as described in Implementing VoIP for IPv6. Media Termination Points Note This section describes how Cisco Unified Communications Manager inserts MTPs into calls that require IPv4 to IPv6 translation. For information on how to configure your Cisco IOS MTP so that the MTP can support IP translation, see Implementing VoIP for IPv6. Note Although the Cisco IOS MTP can support multiple IPv6 addresses, the MTP sends either a global or unique local address to Cisco Unified Communications Manager for signaling and media events. Cisco IOS MTP supports media interoperation between IPv4 and IPv6 networks. Cisco IOS MTP for IPv4-to-IPv6 media translation operates only in dual-stack mode. In Cisco Unified Communications Manager Administration, only the Cisco IOS Enhanced Media Termination Point option for MTPs (Media Resources > Media Termination Point) and transcoders (Media Resources > Transcoder) support the translation 10 OL

11 Media Termination Points functionality; that is, the software MTP component in the Cisco IP Voice Media Streaming Application does not support IPv4 to IPv6 translation. When Cisco Unified Communications Manager allocates an MTP, the MTP may get used for more than one feature at the same time. Because the MTP can get used for multiple features, Cisco Unified Communications Manager prioritizes MTP allocation to ensure that IPv6 and IPv4 are supported before other features that rely on MTP get supported. Under the following circumstances, Cisco Unified Communications Manager inserts an MTP that can translate IPv4 to IPv6 (or vice versa): The devices on the call do not support the same IP address version. For the SIP trunk, you check the Media Termination Points Required check box or configure the Use Trusted Relay Point as On and Cisco Unified Communications Manager is communicating with devices that use IPv6 addresses. If you check the Media Termination Points Required check box for the SIP trunk or you need an MTP inserted into the call for any other reason besides IPv4 to IPv6 translation, the following considerations exist: If both parties of the call can negotiate IPv4 without using an MTP, Cisco Unified Communications Manager does not insert an MTP into the call. When the IP Addressing Mode is IPv6 Only or IPv4 and IPv6 for the SIP trunk, Cisco Unified Communications Manager allocates an MTP that can translate IPv4 to IPv6 (or vice versa) for the call. If no MTP that can translate IP address versions is available for the call, Cisco Unified Communications Manager allocates an MTP that supports IPv4 for the SIP trunk that is configured in dual-stack mode; for a SIP trunk that is configured as IPv6 Only, Cisco Unified Communications Manager sends an INVITE message without SDP session descriptions. When Cisco Unified Communications Manager communicates with the MTP, Cisco Unified Communications Manager requests either an IPv4 or IPv6 address. If Cisco Unified Communications Manager requests an IPv4 address, the MTP opens an RTP port that supports IPv4. If Cisco Unified Communications Manager supports IPv6, the MTP opens an RTP port that supports IPv6. If the request for an MTP that can translate IPv4 to IPv6 fails, the call may fail because IPv6 is required for the call. If an MTP that can translate IP address versions is inserted into the call, any intermediate media device that is inserted between the IPv6 device and the MTP must handle IPv6 requests. If Cisco Unified Communications Manager has two MTPs available and each MTP can perform only one function, Cisco Unified Communications Manager attempts to insert both MTPs into the call, the first MTP for the IPv4-to-IPv6 translation and the second MTP to support other features that require MTP. If a call requires a transcoder and an IPv6-capable MTP and the available transcoder does not support IPv6, Cisco Unified Communications Manager tries to insert the IPv6-capable MTP on the leg of the call that supports IPv6 and the transcoder on the leg of the call that supports IPv4; under these circumstances, the call fails if the IP address capabilities do not match between the MTP and transcoder. Note For information on specific call scenarios where SIP trunks (and MTPs) get used, see Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager. OL

12 SIP Trunks SIP Trunks If configured appropriately, SIP trunks can interact with devices that support IPv4 only, IPv6 only, or dual stack mode (IPv4 and IPv6). Just like Cisco Unified Communications Manager and other components, the SIP trunk uses the configuration for the Enable IPv6 enterprise parameter to determine whether to support devices that use IPv6. IPv4 or IPv6 Signaling for SIP Trunks The following factors determine whether to use IPv4 or IPv6 for signaling events for SIP trunks: The direction of the call IP Addressing Mode for the SIP trunk, as configured in the Common Device Configuration window and applied to the trunk IP Addressing Mode Preference for Signaling configuration for the SIP trunk, as configured in the Common Device Configuration window (or Enterprise Parameter Configuration window) and applied to the trunk Configured Destination Address(es) for the SIP trunk If you configure only one destination address, that is, either the Destination Address, which supports IPv4, or the Destination IPv6 Address, which supports IPv6, ensure that the IP Addressing Mode that you configure for the SIP trunk matches the IP address type that you configured for the destination address. If the configuration does not match, no call gets established over the trunk. If you configure both the Destination Address and the Destination IPv6 Address, make sure that you configure the IP Addressing Mode as IPv4 and IPv6, so the trunk is in dual-stack mode. For a dual-stack trunk, the IP Addressing Mode Preference of Signaling configuration that you applied to the SIP trunk determines whether IPv4 or IPv6 gets used for signaling events for outgoing calls over SIP trunks. IPv4 or IPv6 Media for SIP Trunks The following factors determine whether to use IPv4 or IPv6 for media events for SIP trunks: The direction of the call Whether the call is an early offer or delayed offer call IP address preference in the SDP offer IP Addressing Mode for the SIP trunk, as configured in the Common Device Configuration window and applied to the trunk Configuration for the IP Addressing Mode Preference for Media enterprise parameter, as configured in the Enterprise Parameter Configuration window Configuration for the Enable ANAT check box (and whether ANAT is required or supported in the INVITE) IP Addressing Mode for the phone 12 OL

13 SIP Trunks Note For information on specific call scenarios where SIP trunks (and MTPs) are used, see Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager. IP Address Negotiation For media negotiation for dual-stack devices, Cisco Unified Communications Manager dynamically determines the IP address to use for the call; that is, if any device on the call only supports one IP version, that IP version gets used, and an MTP that can translate IP versions gets inserted into the call. If all devices on the call support both IP versions, and same ANAT address preference is specified by both the devices or at least by one device, that preferred address is negotiated for media. However, if ANAT address preference that is advertised by both devices do not match on both sides or both the devices do not advertise any address preference, for example SCCP, then the configuration for the IP Addressing Mode Preference for Media enterprise parameter gets used. TFTP Server The TFTP server uses IPv4 to communicate with most components, such as the database, in Cisco Unified Communications Manager. If configured appropriately, however, the TFTP server can communicate with devices that use IPv4, IPv6, or both types of addresses. Running in dual-stack mode, the TFTP server can respond to file requests from both IPv4 and IPv6 networks. For requests from IPv4 networks, the TFTP server responds by using an IPv4 stack; for requests from IPv6 networks, the TFTP server responds by using an IPv6 stack; that is, if you set the Enable IPv6 enterprise parameter to True. IPv6 support applies to TFTP requests from devices and HTTP requests from off-cluster TFTP servers where the local TFTP server is configured as their alternate file server. In an IPv6 network, the DHCPv6 server uses the Cisco vendor-specific DHCPv6 information options in the DHCPv6 response message to pass the TFTP IPv6 address to the device. If the device obtains an IPv6 address and sends a request to the TFTP server while the TFTP server is using IPv4 to process requests, the TFTP server does not receive the request because the TFTP server is not listening for the request on the IPv6 stack. In this case, the device cannot register with Cisco Unified Communications Manager. For more information on the Cisco vendor-specific DHCPv6 information options, see the Cisco Unified Communications Manager System Guide and Deploying IPv6 in Unified Communications Networks with Cisco Unified Communications Manager. The TFTP server uses the configuration for the Enable IPv6 enterprise parameter to determine how to communicate with the phone. If you set the Enable IPv6 enterprise parameter to False, the TFTP server uses IPv4 to communicate with the phone. If you set the parameter to True, the TFTP server uses IPv4 or IPv6, depending on the IP Addressing Mode for the phone. If the configuration changes for the Enable IPv6 enterprise parameter, the TFTP server receives a change notification with the new configuration, and the TFTP server enables or disables its IPv6 capabilities without requiring you to restart the Cisco TFTP service. The configuration file that the TFTP server serves to the phone contains the configuration for the following settings: OL

14 System Requirements for IPv6 IP Addressing Mode, IP Addressing Mode Preference for Signaling, and Allow Auto-Configuration for the Phone Host Name/IP Address (IPv4 setting) for the Cisco Unified Communications Manager node IPv6 Name for the Cisco Unified Communications Manager node (only if you set the Enable IPv6 enterprise parameter to True) IPv6 address for the CAPF server (only if you set the Enable IPv6 enterprise parameter to True and activate the Cisco Certificate Authority Proxy Function service) If you configure IPv6 Only as the IP Addressing Mode for phones that are running SIP, the Cisco TFTP service in Cisco Unified Communications Manager overrides the IP Addressing Mode configuration and uses IPv4 Only in the configuration file. Before the TFTP server can serve configuration files to phones that use IPv6 addresses, you must set the Enable IPv6 enterprise parameter to True. If this parameter is set to False, the TFTP server uses an IPv4 address in the configuration file, even if you configured an IP Addressing Mode of IPv6 Only for the devices. The TFTP server obtains the IPv4 and/or IPv6 address from the Cisco Unified Communications Operating System and listens on those addresses for file requests from the phone. In the Service Parameter Configuration window, you can also configure alternate Cisco file servers, which are TFTP servers that are on a different cluster. These parameters, which support either IPv4 or IPv6 addresses or host names that resolve to an IP address, determine the IP stack that the TFTP uses to communicate between primary and alternate file servers. If an alternate file server supports dual-stack mode and you want to set both IPv4 and IPv6 addresses for the same server in these parameter fields, you must add both IP addresses, one per field, and the TFTP server tries each address in the order that you configure. System Requirements for IPv6 The following IPv6 system requirements exist for Cisco Unified Communications Manager: Cisco Unified Communications Manager installed on each server in the cluster DHCPv6 server that can issue IPv6 addresses and DNS server that can resolve host names to IPv6 addresses; consider using Cisco Network Registrar (CNR). If you want to do so, you can configure a Cisco IOS router or switch as a DHCPv6 server; for example, you can configure a Cisco Catalyst 3560 Series Switch or a Cisco Catalyst 3750 Series Switch that runs 12.2(46)SE (or later) as a DHCPv6 server. Before you configure this router/switch, verify that your router/switch supports the Cisco vendor-specific DHCPv6 information options that are required for IPv6 and DHCPv6 support. Cisco IOS release that is compatible with the current release of Cisco Unified Communications Manager, and that is installed and configured on the gateways and the Cisco IOS MTP 14 OL

15 Interactions and Restrictions Cisco Feature Navigator allows you to determine which Cisco IOS and Catalyst OS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to You do not need a Cisco.com account to access Cisco Feature Navigator. Interactions and Restrictions Some Cisco Unified Communications Manager features do not work for devices with an IP Addressing Mode of IPv6 Only. Before you configure IPv6 Only for a device, review the following section, which describes Cisco Unified Communications Manager feature interactions and restrictions for IPv6. Caution You must enable IPv6 in the Cisco Unified Communications Operating System and set the Enable IPv6 enterprise parameter to True; if you do not perform both of these tasks, the Cisco CallManager service runs in IPv4, and phones that you configure with an IP Addressing Mode of IPv6 Only cannot register with Cisco Unified Communications Manager. After you perform these tasks, remember to restart the node. For the order of tasks that you perform for IPv6, see Configure IPv6, on page 1. Caution You can provision your DNS server for IPv6 before you perform an upgrade to the current release. However, do not configure the DNS records for Cisco Unified Communications Manager for IPv6 until after you complete the upgrade. Configuring the DNS records for Cisco Unified Communications Manager for IPv6 before you perform the upgrade causes the upgrade to fail and causes your system to become nonfunctional after you reboot. Annunciator Annunciator supports IPv4; if annunciator connects to a device with an IP Addressing Mode of IPv6 Only, Cisco Unified Communications Manager inserts an MTP that can translate IPv4 to IPv6. If no MTP that can translate IP address versions is available, no announcement plays on the phone. Bulk Administration Tool For information on how the Bulk Administration Tool (BAT) supports IPv6, see the Cisco Unified Communications Manager Bulk Administration Guide. Call Detail Records When IPv6 is used for a call, call detail records (CDRs) can display IPv6 addresses. For more information on CDRs, see the Cisco Unified Communications Manager Call Detail Records Administration Guide. Cisco Certificate Authority Proxy Function For information on how Cisco Certificate Authority Proxy Function works with IPv6, see the Cisco Unified Communications Manager Security Guide. OL

16 Interactions and Restrictions Cisco Extension Mobility Cisco Extension Mobility supports IPv4, so you cannot use phones with an IP Addressing Mode of IPv6 Only for Cisco Extension Mobility. If you want to use Cisco Extension Mobility with the phone, make sure that you configure the phone with an IP Addressing Mode of IPv4 Only or IPv4 and IPv6. Cisco Unified Communications Manager CDR Analysis and Reporting For information on Cisco Unified Communications Manager CDR Analysis and Reporting, see the Cisco Unified Communications Manager CDR Analysis and Reporting Administration Guide. Cisco Unified Communications Operating System See the Configure IPv6, on page 1 and the Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window, on page 20. Cisco Unified Serviceability Alarms that report IPv4 addresses may also report IPv6 addresses, depending on the configuration in your network. For information on how to configure alarms and view alarm definitions in Cisco Unified Serviceability, see the Cisco Unified Serviceability Administration Guide. SNMP supports IPv4, although the CISCO-CCM-MIB includes columns and storage for IPv6 addresses, preferences, and so on. Cisco Unity Connection and Cisco Unity Cisco Unity Connection and Cisco Unity communicate with Cisco Unified Communications Manager by using IPv4. Cisco Unified Communications Manager Assistant Cisco Unified Communications Manager Assistant does not support IPv6, so you cannot use phones with an IP Addressing Mode of IPv6 Only with Cisco Unified Communications Manager Assistant. If you want to use Cisco Unified Communications Manager Assistant with the phone, make sure that you configure the phone with an IP Addressing Mode of IPv4 Only or IPv4 and IPv6. Real Time Monitoring Tool In RTMT, you can monitor CTI applications, CTI devices, and CTI lines that use IPv6 addresses. When you search for the CTI application, CTI device, or CTI line, enter the IPv6 address, and check the AppIpv6Addr check box in the attribute window. In addition, you can perform a device search on phones or SIP trunks that use IPv6 addresses. When you choose CallManager > Device Search > Open Device Search > Phones (or SIP Trunks), make sure that you specify an IPv6 address and check the Ipv6Address check box in the attributes window. Log files may display IPv4 and IPv6 addresses, depending on the configuration in your network. In RTMT, performance monitoring counters display for the IP6 object. Cisco Web Dialer Cisco Web Dialer supports IPv4, so, to connect to CTI Manager, Cisco Web Dialer uses an IPv4 address. Cisco Web Dialer works with devices with an IP Addressing Mode of IPv4 and IPv6. 16 OL

17 Interactions and Restrictions Conferences (Audio) Cisco Unified Communications Manager uses IPv4 for conferences, even if the conference bridge uses IPv6. During a conference, Cisco Unified Communications Manager inserts one MTP that can translate IPv4 to IPv6 for each device with an IP Addressing Mode of IPv6 Only, so each phone that uses an IPv6 address can join the conference. For your MTP device to support security, you must configure the MTP in pass-through mode, which means that the MTP does not transform the media payload during the call. When you configure an MTP in pass-through mode, the MTP receives the encrypted packet on one call leg and sends out the same packet on a different leg of the call. For secure conferences with secure conference bridges and encrypted devices with an IP Addressing Mode of IPv6 Only, Cisco Unified Communications Manager inserts an MTP into the conference to translate IPv4 to IPv6 (and vice versa) when some devices in the conference support IPv4. If you configure the MTP for pass-through mode, the encrypted IPv6 phones communicate with the conference bridge using SRTP. If you do not configure the MTP for pass-through mode, the media gets downgraded to RTP. Device Mobility Device mobility supports IPv4 addresses only, so you cannot use phones with an IP Addressing Mode of IPv6 Only with device mobility. Differentiated Services Control Point (DSCP) Be aware that Differentiated Services Control Point (DSCP) values are the same for both IPv6 and IPv4. Disaster Recovery System For information on Disaster Recovery System, see the Disaster Recovery System Administration Guide. H.323 Devices H.323 clients, gateways, and H.225 intercluster trunks do not support IPv6. To communicate with IPv6-only devices that connect to these gateways, Cisco Unified Communications Manager inserts an MTP that can translate IPv4 to IPv6 during a call. Intercom Intercom can support phones with an IP Addressing Mode of IPv4 Only or IPv4 and IPv6. During an intercom call, the talkback mode establishes media streams with the same IP version as the media stream that is used when the caller initiated intercom. Mobile Connect and Mobile Voice Access Cisco Unified Mobility features in Cisco Unified Communications Manager, such as Mobile Connect and Mobile Voice Access, support IPv4. On a call, when a mobile phone uses IPv4 and another phone uses IPv6, Cisco Unified Communications Manager inserts a Media Termination Point (MTP) that can translate IPv4 to IPv6 into the call. Monitoring and Recording For monitoring and recording, the phone can handle an IPv4 media stream for customer-to-agent calls while it handles an IPv6 media stream for recording and monitoring (or vice versa). OL

18 Interactions and Restrictions Music On Hold The Cisco IP Voice Media Streaming Application service supports IPv4. Cisco Unified Communications Manager does not support IPv6 with multicast Music On Hold, so devices with an IP Addressing Mode of IPv6 Only cannot support multicast Music On Hold. Under these circumstances, Cisco Unified Communications Manager plays a tone, instead of music, when the phone is on hold. For IPv6 Only devices that uses unicast Music On Hold, Cisco Unified Communications Manager inserts an MTP that can translate IPv4 to IPv6 (or vice versa) into the media stream. NTP Servers To avoid potential compatibility, accuracy, and network jitter problems, ensure that the external NTP servers that you specify for the primary node are NTP v4 (version 4). QRT Users with phones with an IP Addressing Mode of IPv6 Only cannot report audio and other problems by pressing the QRT softkey on the phone. In addition, the QRT report does not include the streaming statistics for a phone that has an IP Addressing Mode of IPv6 Only. RSVP If you deploy RSVP as the call admission control mechanism in your network, do not deploy IPv6. The RSVP feature does not support IPv6. RSVP calls support IPv4. If RSVP is required for the call and any device in the call is configured for or uses an IPv6 address, Cisco Unified Communications Manager rejects the call, and the caller receives a busy tone. SDL SDL TCP connections support IPv6, but SDL links support IPv4. If you configure a hostname in the Server Configuration window in Cisco Unified Communications Manager Administration, SDL queries the DNS A record, which ensures that IPv4 is used. If you specify an IP address, an IPv4 address gets passed down to the SDL layer. Security (TLS and SRTP) For information on how TLS and SRTP work with IPv6, see the Cisco Unified Communications Manager Security Guide. SIP Phones and TFTP Phones that run SIP do not support IPv6 addresses. If you configure IPv6 Only as the IP Addressing Mode for a phone that runs SIP, the Cisco TFTP service overrides the IP Addressing Mode configuration and uses IPv4 Only in the configuration file. T.38 Fax Whether a T.38 fax call uses IPv4 or IPv6 depends on the preference of Cisco Unified Communications Manager and the capabilities of the devices in the call. If one device in the call uses IPv6 and the other device can use IPv4 and IPv6, the call uses IPv6, regardless of the configuration for the signaling and media enterprise parameters in Cisco Unified Communications Manager Administration. Cisco Unified Communications Manager supports the following types of T.38 fax calls: SIP-to-SIP call that uses IPv6 18 OL

19 Install and Activate IPv6 SIP-to-SIP call that uses IPv4 SIP-to-non-SIP call that uses IPv4 SIP-to-non-SIP call where the SIP device uses IPv6 and the non-sip device uses IPv4 with an MTP that can translate IP address versions During the middle of a T.38 fax call, Cisco Unified Communications Manager does not insert an MTP that converts the IP version types; the MTP must already exist in the call. Transfer The transfer components in Cisco Unified Communications Manager uses the IP Addressing Mode and the IP address of the device to determine how to handle the transfer. If the IP capabilities do not match when you transfer a call, Cisco Unified Communications Manager allocates an MTP that can translate IP version, so the transfer can occur. Web Browser on the Phone On the Cisco Unified IP Phone, the HTTP interface for the web browser supports IPv4 addresses, so the phone does not allow web access to servers that use an IPv6 address. Video and Application Media Streams Cisco Unified Communications Manager Release 9.0 does not support video IPv6 calls: Cisco Unified Video Advantage does not support IPv6, so video always uses IPv4. The audio and video portions of a call must always use the same IP type; video is disabled for any IPv6 or dual-stack phone that is associated with Cisco Unified Video Advantage. Install and Activate IPv6 IPv6 Configuration After you install Cisco Unified Communications Manager, your network can support IPv6 if you perform the necessary configuration tasks. For information on configuration tasks that you must perform, see the Configure IPv6, on page 1. IPv6 impacts the Cisco CallManager, CTIManager, and Certificate Authority Proxy Function services in Cisco Unified Serviceability. Depending on the configuration tasks that you perform in Cisco Unified Communications Manager Administration, you may need to restart these services after you configure IPv6. This section provides information to configure IPv6. Before you configure IPv6, review the configuration summary task for this feature. Related Topics Configure IPv6, on page 1 OL

20 Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window To enable IPv6 in the Cisco Unified Communications Operating System and to ensure that the Cisco Unified Communications Manager node gets an IPv6 address, you must perform one of the following tasks: Run the IPv6 CLI commands in the command line interface. Enable IPv6 and configure the IPv6 address in the Ethernet IPv6 window in the Cisco Unified Communications Operating System. Caution Before you set the Enable IPv6 enterprise parameter to True in Cisco Unified Communications Manager Administration, perform the following procedure. If you set the enterprise parameter to True before you enable IPv6 in the Cisco Unified Communications Operating System, the Cisco CallManager service runs in IPv4, and phones that have IP Addressing Mode of IPv6 Only cannot register with Cisco Unified Communications Manager. The following table provides a description of the Ethernet IPv6 configuration settings and the equivalent CLI commands that support the graphical user interface (GUI) options. Table 1: IPv6 CLI Commands and Ethernet IPv6 Configuration Settings Configuration Setting in Ethernet IPv6 Window Enable IPv6 check box Equivalent CLI Command set network ipv6 service enable Description These settings enable IPv6 in the Cisco Unified Communications Operating System. Caution For IPv6 to work, you must either check the Ethernet IPv6 check box or issue the equivalent CLI command. You must perform this task before you set the Enable IPv6 enterprise parameter to True. 20 OL

21 Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window Configuration Setting in Ethernet IPv6 Window Router Advertisement radio button DHCP radio button Equivalent CLI Command Not applicable set network ipv6 dhcp enable Description If you want to use stateless address autoconfiguration to obtain a non-link-local IPv6 address for the Cisco Unified Communications Manager node, click the Router Advertisement radio button. Click this radio button if you do not plan to configure a static non-link-local IPv6 address for the Cisco Unified Communications Manager node or if you do not want DHCPv6 server to issue a non-link-local IPv6 address to the node. Ensure that the Cisco Unified Communications Manager node only obtains one non-link-local IPv6 address. If the node has more than one IPv6 address, Cisco Unified Communications Manager may not behave as expected. If the Cisco Unified Communications Manager node obtains an IPv6 address via stateless address autoconfiguration and you also have a static IPv6 address that is configured for the node, Cisco Unified Communications Manager ignores the IPv6 address that is obtained via stateless address autoconfiguration and uses the static address. If you want the DHCPv6 server to issue a non-link-local IPv6 address to the Cisco Unified Communications Manager node, click the DHCP radio button or issue the equivalent CLI command. Ensure that the Cisco Unified Communications Manager node only obtains one non-link-local IPv6 address. If the node has more than one IPv6 address, Cisco Unified Communications Manager may not behave as expected. OL

22 Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window Configuration Setting in Ethernet IPv6 Window Manual Entry radio button, IPv6 Address, Subnet Mask IPv6 Address Equivalent CLI Command set network ipv6 static_address <addr> <mask> show network ipv6 settings Description These Ethernet IPv6 settings and equivalent CLI command allow you to configure a static IPv6 address for the Cisco Unified Communications Manager node. Configuring a static non-link-local IPv6 address assumes that you do not want the Cisco Unified Communications Manager node to get the IPv6 address from the DHCPv6 server or via stateless address autoconfiguration. These settings allow you to view the IPv6 address for the Cisco Unified Communications Manager node. If you chose to use the CLI commands instead of configuring the Ethernet IPv6 settings in the Cisco Unified Communications Operating System, you must reboot the node for the changes to take effect. For information on how to run CLI commands and for other IPv6 CLI commands, see the Command Line Interface Reference Guide for Cisco Unified Communications Solutions. Note After you enable IPv6 through the CLI, you must enter the IPv6 Name field from Server > Server Configuration. Procedure Step 1 Step 2 Step 3 Step 4 Step 5 In Cisco Unified Communications Operating System, choose Settings > IP > Ethernet IPv6. The Ethernet IPv6 Configuration window displays. Modify the Ethernet settings values in the appropriate fields in the Ethernet IPv6 Configuration window. Check the Update with Reboot check box. For the IPv6 settings in this window to take effect, you must reboot the node. Click Save. The node reboots immediately after you click Save. Perform this procedure for each node in the cluster. 22 OL

23 Configure Service and Enterprise Parameters for IPv6 Configure Service and Enterprise Parameters for IPv6 The following table describes the enterprise and service parameters that you can configure for IPv6. To configure enterprise parameters in Cisco Unified Communications Manager Administration, choose System > Enterprise Parameters. To configure service parameters in Cisco Unified Communications Manager Administration, choose System > Service Parameters. For a step-by-step procedure on how to configure enterprise parameters, see the Cisco Unified Communications Manager Administration Guide. For a step-by-step procedure on how to configure service parameters, see the Cisco Unified Communications Manager Administration Guide. Table 2: Enterprise and Service Parameters for IPv6 Parameter Enable IPv6 IP Addressing Mode Preference for Media IP Addressing Mode Preference for Signaling Description This enterprise parameter specifies whether Cisco Unified Communications Manager can negotiate calls by using IPv6 and whether the phone can advertise an IPv6 address. Before you set this parameter to True, make sure that you enabled IPv6 in the Cisco Unified Communications Operating System on all servers in the cluster. Setting this parameter to True causes the Cisco CallManager service to run in dual-stack mode, which is required for interacting with devices that support IPv6. The default value equals False, which means that Cisco Unified Communications Manager cannot negotiate calls by using IPv6 and phones cannot advertise an IPv6 address. After you update this enterprise parameter, restart the Cisco CallManager, Cisco IP Voice Media Streaming App, Cisco CTIManager, Cisco Certificate Authority Proxy Function, and the Cisco IPVMS services in Cisco Unified Serviceability. This enterprise parameter, which applies only to dual-stack devices, specifies the preferred addressing mode that Cisco Unified Communications Manager uses for media events when both IPv4 and IPv6 addresses are available from each device on the call. The default value equals Prefer IPv4. This enterprise parameter, which applies only to dual-stack devices, specifies how the dual-stack phone connects to Cisco Unified Communications Manager for signaling events and how the dual-stack SIP trunk connects to the peer device for signaling events. The default value equals Prefer IPv4. Allow Auto-Configuration for Phones This parameter determines whether the phone is allowed to obtain an address through stateless autoconfiguration. Valid values specify On (the phone obtains its address as specified by the router advertisements, which may be stateless or stateful, depending on the router configuration) or Off (the phone always uses DHCPv6 to obtain its IPv6 address). OL

24 Access IPv6 and IPv4 Configuration in Unified CM Administration Parameter Call Counting CAC Enabled Audio Bandwidth For Call Counting CAC Video Bandwidth For Call Counting CAC Alternate Cisco File Server(s) Description This service parameter, which supports the Cisco CallManager service, determines whether Cisco Unified Communications Manager uses call counting as part of the locations-based call admission control (CAC) feature. Call counting uses a fixed bandwidth value to reserve and adjust bandwidth per call, regardless of the codec or media payload or the Internet Protocol Version (IPv6 or IPv4) that is used for each call. Call counting may potentially oversubscribe or undersubscribe bandwidth because a fixed-value bandwidth gets reserved per call no matter what the actual bandwidth is for the call. Cisco recommends that you leave this parameter set to the default value of False (disabled) unless your network requires the call counting feature. To enable call counting for CAC, choose True for the parameter; to disable call counting for CAC, choose False. This service parameter applies to IPv4 and IPv6 calls. This service parameter, which supports the Cisco CallManager service, specifies the amount of bandwidth to deduct from the available bandwidth for audio calls after you set the Call Counting CAC Enabled parameter to True. For each audio call, the amount of bandwidth that you enter in this field gets deducted, regardless whether more or less bandwidth is actually used for the call. This service parameter applies to IPv4 and IPv6 calls. This service parameter, which supports the Cisco CallManager service, specifies the units of bandwidth to deduct from the available bandwidth for video calls after you set the Call Counting CAC Enabled parameter to True. For each video call, the available bandwidth gets reduced by the number of units that are required to account for the actual bandwidth usage. For example, if you specify 512 kbps as the bandwidth unit in this parameter, and a video call utilizes 384 kbps, then one unit, 512 kbps, gets deducted from available bandwidth. If you specify 512 kbps in this parameter and a video call negotiated 768 kbps, then two units of bandwidth (1064 kbps) get deducted from the available bandwidth. This service parameter applies to IPv4 and IPv6 calls. These service parameters, which support the Cisco TFTP service, allow you to configure alternate Cisco file servers, which are TFTP servers that are on a different cluster. These parameters, which support either IPv4 or IPv6 addresses or host names that resolve to an IP address, determine the IP stack that the TFTP uses to communicate between primary and alternate file servers. If an alternate file server supports dual-stack mode and you want to set both IPv4 and IPv6 addresses for the same server in these parameter fields, you must add both IP addresses, one per field, and the TFTP server tries each address in the order that you configure. Access IPv6 and IPv4 Configuration in Unified CM Administration The following table describes the IPv6 and IPv4 settings that are in Cisco Unified Communications Manager Administration, except for IPv6 service and enterprise parameters, which are described in Configure Service and Enterprise Parameters for IPv6, on page 23. For some IPv6 settings in the following table, equivalent 24 OL

25 Access IPv6 and IPv4 Configuration in Unified CM Administration settings for IPv4 display in Cisco Unified Communications Manager Administration; for example, in the SIP Trunk Configuration window, you can configure the Destination Address IPv6 setting or the Destination Address setting, or both settings, depending on the IP support in your network. Configuration Setting System > Server Description Host Name/IP Address IPv6 Name This field supports IPv4. If your network uses DNS that can map to IPv4 addresses, you can enter the host name of the Cisco Unified Communications Manager node. Otherwise, you must enter the full IPv4 address of the node. If your network supports IPv6 (or IPv4 and IPv6), configure the IPv6 Name field in addition to the Host Name/IP Address field. This field supports IPv6. If your network uses DNS that can map to IPv6 addresses, you can enter the host name of the Cisco Unified Communications Manager node. Otherwise, enter the non-link-local IP address of the Cisco Unified Communications Manager node. Phones that run SCCP use this field, which gets included in the TFTP configuration file, to retrieve the IPv6 address of the Cisco Unified Communications Manager node, so phone registration occurs. You can provision your DNS server for IPv6 prior to upgrading to the current release. However, do not configure the DNS records for Cisco Unified Communications Manager for IPv6 until after you complete the upgrade. Configuring the DNS records for Cisco Unified Communications Manager for IPv6 prior to completing the upgrade causes the upgrade to fail and causes your system to become nonfunctional after you reboot. In addition to configuring the IPv6 Name field, you must configure the Host Name/IP Address field, so Cisco Unified Communications Manager can support features/devices that use IPv4 (or IPv4 and IPv6). Call Routing > SIP Route Patterns IPv4 Pattern IPv6 Pattern Enter the domain, sub-domain, IPv4 address or IP subnetwork address. For the IP subnetwork address, in Classless Inter-Domain Routing (CIDR) notation, enter X.X.X.X/Y, where Y equals the network prefix that denotes the number of bits in the address that will be the network address. If the SIP trunk supports IPv6 or both IPv4 and IPv6 (dual-stack mode), configure the IPv6 Pattern in addition to the IPv4 pattern. Cisco Unified Communications Manager uses SIP route patterns to route or block both internal and external calls. The IPv6 address in this field provides the basis for routing internal and external calls to SIP trunks that support IPv6. If the SIP trunk supports both IPv4 and IPv6, configure the IPv4 Pattern in addition to the IPv6 Pattern. Device > Device Settings > Common Device Configuration OL

26 Access IPv6 and IPv4 Configuration in Unified CM Administration Configuration Setting IP Addressing Mode Description Choose the version of IP address that the device (SIP trunks, or phones that run SCCP) uses to connect to Cisco Unified Communications Manager. From the drop-down list box, choose one of the following options: IPv4 Only - For both media and signaling events, the device uses an IPv4 address to connect to Cisco Unified Communications Manager. If an IPv4 address is not available for the device, the call fails. If you choose this option, the phone releases an IPv6 address. If you choose this option, the SIP trunk uses an IPv4 address to connect to the peer device. IPv6 Only - For both media and signaling events, the device uses an IPv6 address to connect to Cisco Unified Communications Manager. If an IPv6 address is not available for the device, the call fails. If you choose this option, the phone releases an IPv4 address. If you choose this option, the SIP trunk uses an IPv6 address to connect to the peer device. Phones that run SIP do not support IPv6, so do not choose this option for these phones. If you configure IPv6 Only as the IP Addressing Mode for phones that run SIP, the Cisco TFTP service overrides the IP Addressing Mode configuration and uses IPv4 Only in the configuration file. IPv4 and IPv6 (Default) - Choose this option for dual-stack devices, which can have both an IPv4 and IPv6 address. For both media and signaling events, the dual-stack device uses either an IPv4 or an IPv6 address to connect to Cisco Unified Communications Manager. If the device has both IPv4 or IPv6 addressing available, it uses the settings configured for the following parameters: IP Addressing Mode Preference for Signaling parameter for signaling events IP Addressing Mode Preference for Media enterprise parameter for media events IP Addressing Mode Preference for Signaling For dual-stack phones, which support both IPv4 and IPv6 addresses, choose the version of IP address that the phone prefers to establish a connection to Cisco Unified Communications Manager during a signaling event. For dual-stack SIP trunks, choose the version of IP address that the SIP trunk uses to connect to the peer device for signaling events. From the drop-down list box, choose one of the following options: IPv4 - The dual-stack device prefers to establish a connection via an IPv4 address during a signaling event. IPv6 - The dual-stack device prefers to establish a connection via an IPv6 address during a signaling event. Use System Default - The configuration for the enterprise parameter, IP Addressing Mode Preference for Signaling, applies. 26 OL

27 Access IPv6 and IPv4 Configuration in Unified CM Administration Configuration Setting Allow Auto-Configuration for Phones Description This drop-down list box supports IPv6 for dual-stack Cisco Unified IP Phones that run SCCP. From the drop-down list box, choose one of the following options: On - Depending on how the M bit is set via stateless address autoconfiguration on the router, the phone is allowed to use the IPv6 Network ID that is advertised in the Router Advertisements (RAs) to autoconfigure its IPv6 address. Phones also require a TFTP server address to register with Cisco Unified Communications Manager. You can manually configure the TFTP server address via the interface on the phone, or you can obtain it from a DHCPv6 server. To indicate to the phone that it needs to use the DHCPv6 server to obtain other information, ensure that the O bit is set via stateless address autoconfiguration on the router. Off - The phone obtains its IPv6 address and TFTP server address from the DHCPv6 server. Default - To use the configuration for the Allow Auto-Configuration for Phones enterprise parameter, choose this option. Although Cisco Unified Communications Manager does not use this configuration, the TFTP file that the phone obtains includes this information. Device > SIP Trunk Destination Address The Destination Address, which supports IPv4, represents the remote SIP peer with which this trunk will communicate. The allowed values for this field specify a valid V4 dotted IP address, fully qualified domain name (FQDN), or DNS SRV record only if the Destination Address is an SRV field is checked. SIP trunks only accept incoming requests from the configured Destination Address and the specified incoming port that is specified in the SIP Trunk Security Profile that is associated with this trunk. If the remote end is a Cisco Unified Communications Manager cluster, DNS SRV represents the recommended choice for this field. The DNS SRV record should include all Cisco Unified Communications Managers within the cluster. For SIP trunks that can support IPv6 or IPv6 and IPv4 (dual-stack mode), configure the Destination Address IPv6 field in addition to the Destination Address field. OL

28 Access IPv6 and IPv4 Configuration in Unified CM Administration Configuration Setting Destination Address IPv6 Description The Destination IPv6 Address represents the remote SIP peer with which this trunk will communicate. Enter one for the following values in the field: A valid IPv6 address (global unicast, unique local, or a host name) A fully qualified domain name (FQDN) A DNS SRV record, but only if you check the Destination Address is an SRV check box. SIP trunks only accept incoming requests from the configured Destination IPv6 Address and the specified incoming port that is specified in the SIP Trunk Security Profile that is associated with this trunk. If the remote end is a Cisco Unified Communications Manager cluster, consider entering the DNS SRV record in this field. The DNS SRV record should include all Cisco Unified Communications Managers within the cluster. For SIP trunks that run in dual-stack mode or that support an IP Addressing Mode of IPv6 Only, configure this field. If the SIP trunk runs in dual-stack mode, you must also configure the Destination Address field. Device > Device Settings > SIP Profile Enable ANAT This option allows a dual-stack SIP trunk to offer both IPv4 and IPv6 media. When you check both the Enable ANAT and the Media Termination Point Required check boxes, Cisco Unified Communications Manager inserts a dual-stack MTP and sends out an offer with two m-lines, one for IPv4 and another for IPv6. If a dual- stack MTP cannot be allocated, Cisco Unified Communications Manager sends an INVITE without SDP. When you check the Enable ANAT check box and the Media Termination Point Required check box is unchecked, Cisco Unified Communications Manager sends an INVITE without SDP. When both the Enable ANAT and Media Termination Point Required check boxes display as unchecked (or when an MTP cannot be allocated), Cisco Unified Communications Manager sends an INVITE without SDP. When you uncheck the Enable ANAT check box but you check the Media Termination Point Required check box, consider the information, which assumes that an MTP can be allocated: Cisco Unified Communications Manager sends an IPv4 address in the SDP for SIP trunks with an IP Addressing Mode of IPv4 Only. Cisco Unified Communications Manager sends an IPv6 address in the SDP for SIP trunks with an IP Addressing Mode of IPv6 Only. For dual-stack SIP trunks, Cisco Unified Communications Manager determines which IP address type to send in the SDP based on the configuration for the IP Addressing Mode Preference for Media enterprise parameter. 28 OL

29 Provide Information to Users Related Topics Run IPv6 CLI Commands or Configure IPv6 in the Ethernet IPv6 Window, on page 20 Provide Information to Users No special considerations exist for phone (end) users, although IPv6 menu options display on the phone. Be aware, though, that if you do not configure the IP address support correctly in your network, users may receive a busy tone, dead air, and so on, when trying to place or answer calls on the phone. For additional information on using IPv6 with your phone, see the Cisco Unified IP Phone Administration Guide that supports your phone model and this version of Cisco Unified Communications Manager. Troubleshooting IPv6 For information on troubleshooting IPv6, see the Cisco Unified Communications Manager Troubleshooting Guide. OL

Internet Protocol Version 6 (IPv6)

Internet Protocol Version 6 (IPv6) CHAPTER 29 Internet Protocol version 6 (IPv6), which is the latest version of the Internet Protocol (IP) that uses packets to exchange data, voice, and video traffic over digital networks, increases the

More information

Configure Dual Stack IPv6

Configure Dual Stack IPv6 Dual Stack Addressing Overview, on page 1 Dual Stack IPv6 Prerequisites, on page 2 Dual Stack IPv6 Configuration Task Flow, on page 2 Dual Stack Addressing Overview If your SIP deployment requires IPv6

More information

Configure IPv6 Stack. IPv6 Stack Overview. IPv6 Stack Overview, page 1 IPv6 Prerequisites, page 2 IPv6 Configuration Task Flow, page 2

Configure IPv6 Stack. IPv6 Stack Overview. IPv6 Stack Overview, page 1 IPv6 Prerequisites, page 2 IPv6 Configuration Task Flow, page 2 IPv6 Stack Overview, page 1 IPv6 Prerequisites, page 2 IPv6 Configuration Task Flow, page 2 IPv6 Stack Overview IPv6 is an expanded IP addressing protocol that uses 128 bits instead of the 32 bits that

More information

IP Addressing Modes for Cisco Collaboration Products

IP Addressing Modes for Cisco Collaboration Products IP Addressing Modes for Cisco Collaboration Products IP Addressing Modes, on page 1 Recommended IPv6 Addressing Modes for CSR 12.1/12.0 Products, on page 2 IPv6 Addressing in Cisco Collaboration Products,

More information

IP Addressing Modes for Cisco Collaboration Products

IP Addressing Modes for Cisco Collaboration Products IP Addressing Modes for Cisco Collaboration Products IP Addressing Modes, page 1 Recommended IPv6 Addressing Modes for CSR 12.0 Products, page 3 IPv6 Addressing in Cisco Collaboration Products, page 9

More information

Cisco Unified IP Phone Settings

Cisco Unified IP Phone Settings Phone Settings Overview, page 1 Cisco Unified IP Phones 7906G and 7911G Menus, page 1 Phone Setup s, page 4 Network Configuration Menu, page 5 Device Configuration Menu, page 17 Security Configuration

More information

Configuring Trace. Configuring Trace Parameters CHAPTER

Configuring Trace. Configuring Trace Parameters CHAPTER CHAPTER 7 Note Enabling trace decreases system performance; therefore, enable trace only for troubleshooting purposes. For assistance in using trace, contact your technical support team. This chapter contains

More information

Server Configuration. Server Configuration Settings CHAPTER

Server Configuration. Server Configuration Settings CHAPTER CHAPTER 2 This chapter contains information on the following topics: Settings, page 2-1 Related Topics, page 2-6 Settings In Cisco Unified Communications Manager Administration, use the System > Server

More information

Cisco Unified CM Trace

Cisco Unified CM Trace Cisco Unified CM Trace Trace, page 1 Configure trace, page 4 Set up troubleshooting trace settings, page 20 Trace Cisco Unified Serviceability provides trace tools to assist you in troubleshooting issues

More information

Cisco Unified Communications Manager TCP and UDP Port

Cisco Unified Communications Manager TCP and UDP Port Cisco TCP and UDP Port Usage This chapter provides a list of the TCP and UDP ports that Cisco uses for intracluster connections and for communication with external applications or devices. You will also

More information

Client services framework setup

Client services framework setup In Cisco Unified Communications Manager Administration, use the Device > Phone menu path to configure the Cisco Unified Client Services Framework device. This section describes how to configure a Cisco

More information

Cisco Unified Communications Manager TCP and UDP Port

Cisco Unified Communications Manager TCP and UDP Port Cisco TCP and UDP Port Usage This chapter provides a list of the TCP and UDP ports that Cisco uses for intracluster connections and for communication with external applications or devices. You will also

More information

Common Device Configuration

Common Device Configuration CHAPTER 77 Use the following topics to configure common device configurations: Settings, page 77-1 Synchronizing a With Affected Devices, page 77-7 Related Topics, page 77-8 Settings In Cisco Unified Communications

More information

Cisco Unified IP Phone setup

Cisco Unified IP Phone setup Cisco Unified IP Phone setup This chapter provides information about working with and configuring Cisco Unified IP Phones in Cisco Unified Communications Manager Administration. About Cisco Unified IP

More information

Cisco Unified IP Phone setup

Cisco Unified IP Phone setup This chapter provides information about working with and configuring Cisco Unified IP Phones in Cisco Unified Communications Manager Administration. About Cisco Unified IP Phones and device setup, page

More information

Cisco TelePresence Conductor with Cisco Unified Communications Manager

Cisco TelePresence Conductor with Cisco Unified Communications Manager Cisco TelePresence Conductor with Cisco Unified Communications Manager Deployment Guide TelePresence Conductor XC4.0 Unified CM 10.5(2) January 2016 Contents Introduction 6 About this document 6 Related

More information

Configuring Services. Activating and Deactivating Feature Services CHAPTER

Configuring Services. Activating and Deactivating Feature Services CHAPTER CHAPTER 11 This chapter contains information on the following topics: Activating and Deactivating Feature s, page 11-1 Cluster Activation Recommendations, page 11-2 Starting, Stopping, Restarting, and

More information

System-Level Configuration Settings

System-Level Configuration Settings CHAPTER 5 Configure system-level settings before you add devices and configure other Cisco Unified CallManager features. This section covers the following topics: Server Configuration, page 5-1 Cisco Unified

More information

Cisco Unified Communications Manager Trunk Types

Cisco Unified Communications Manager Trunk Types Cisco Unified Communications Manager Trunk Types This chapter provides information about trunk types. In a distributed call-processing environment, Cisco Unified Communications Manager communicates with

More information

Encryption setup for gateways and trunks

Encryption setup for gateways and trunks Encryption setup for gateways and trunks This chapter provides information about encryption setup for gateways and trunks. Cisco IOS MGCP gateway encryption, page 1 H.323 gateway and H.323/H.225/H.245

More information

Post-Change Tasks and Verification

Post-Change Tasks and Verification Post-Change Task List for Cisco Unified Communications Manager Nodes, page 1 Post-Change Task List for IM and Presence Service Nodes, page 3 Perform Post-Change Tasks for Cisco Unified Communications Manager

More information

Configure Cisco IP Phones

Configure Cisco IP Phones Cisco IP Phones Overview, page 1 Cisco IP Phones Configuration Task Flow, page 1 Cisco IP Phones Overview Cisco Unified IP Phones are full-featured telephones that provide voice communication over an IP

More information

System-Level Configuration Settings

System-Level Configuration Settings CHAPTER 5 Configure system-level settings before you add devices and configure other Cisco Unified Communications Manager features. This section covers the following topics: System Configuration Checklist,

More information

Cisco Unified IP Phone Configuration

Cisco Unified IP Phone Configuration CHAPTER 67 Cisco Unified IP Phones as full-featured telephones can plug directly into your IP network. You use the Cisco Unified Communications Manager Administration Phone Configuration window to configure

More information

Cisco.Certkiller v by.Luger.57q. Exam Code:

Cisco.Certkiller v by.Luger.57q. Exam Code: Cisco.Certkiller.642-447.v2013-12-24.by.Luger.57q Number: 642-447 Passing Score: 825 Time Limit: 120 min File Version: 16.5 http://www.gratisexam.com/ Exam Code: 642-447 Exam Name: Cisco CIPT1 v8.0 Implementing

More information

Number: Passing Score: 800 Time Limit: 120 min File Version: Cisco Questions & Answers

Number: Passing Score: 800 Time Limit: 120 min File Version: Cisco Questions & Answers 642-427 Number: 642-427 Passing Score: 800 Time Limit: 120 min File Version: 29.0 Cisco 642-427 Questions & Answers Troubleshooting Cisco Unified Communications v8.0 (TVOICE v8.0) Version: 29.0 Cisco 642-427

More information

Computer Telephony Integration

Computer Telephony Integration This chapter provides information about Computer telephony integration (CTI) which enables you to leverage computer-processing functions while making, receiving, and managing telephone calls. CTI applications

More information

Cisco TelePresence Conductor with Unified CM

Cisco TelePresence Conductor with Unified CM Cisco TelePresence Conductor with Unified CM Deployment Guide TelePresence Conductor XC3.0 Unified CM 10.x Revised February 2015 Contents Introduction 5 About this document 5 Related documentation 5 About

More information

Setting Up a Cisco Unified Communications Manager SIP Trunk Integration, page 1

Setting Up a Cisco Unified Communications Manager SIP Trunk Integration, page 1 Up a Cisco Unified Communications Manager SIP Trunk Integration This chapter provides instructions for setting up a Cisco Unified Communications Manager SIP trunk integration with Cisco Unity Connection.

More information

Configuring Encryption for Gateways and Trunks

Configuring Encryption for Gateways and Trunks CHAPTER 24 This chapter contains information on the following topics: Overview for Cisco IOS MGCP Gateway Encryption, page 24-1 Overview for H.323 Gateway and H.323/H.225/H.245 Trunk Encryption, page 24-2

More information

Unified Communications Manager FAQ

Unified Communications Manager FAQ Unified Communications Manager FAQ Document ID: 111900 Contents Introduction Is it possible to control the quota for outside calls with Cisco Unified Communications Manager? How many calls can be handled

More information

CCNP Voice (CCVP) Syllabus/Module Details CVOICE Cisco Voice over IP and QoS v8.0 (CVOICE v8.0)

CCNP Voice (CCVP) Syllabus/Module Details CVOICE Cisco Voice over IP and QoS v8.0 (CVOICE v8.0) CCNP Voice (CCVP) Syllabus/Module Details 642-437 CVOICE Cisco Voice over IP and QoS v8.0 (CVOICE v8.0) 642-447 CIPT1 Implementing Cisco Unified Communications Manager, Part 1 v8.0 (CIPT1 v8.0) 642-457

More information

Command or Action Step 1. Create and Configure Cisco Jabber Devices, on page 1. Configure a SIP Trunk, on page 6

Command or Action Step 1. Create and Configure Cisco Jabber Devices, on page 1. Configure a SIP Trunk, on page 6 s Workflow, page 1 s Workflow Command or Action Purpose Create and Configure Cisco Jabber Devices, on page 1 Create at least one device for every user that will access Cisco Jabber. Configure a SIP Trunk,

More information

Getting Started with the VG248

Getting Started with the VG248 CHAPTER 2 Before you can configure the telephony features on the VG248 to interact with the analog phones, you must first configure the basic network, SNMP, and password settings. These settings enable

More information

Cisco Unified Communications Manager configuration for integration with IM and Presence Service

Cisco Unified Communications Manager configuration for integration with IM and Presence Service Cisco Unified Communications Manager configuration for integration with IM and Presence Service User and Device Configuration on Cisco Unified Communications Manager before Integration Task List, page

More information

Configure Server Information

Configure Server Information System Information Overview, on page 1 Server Configuration Task Flow, on page 1 Hostname Configuration, on page 3 System Information Overview This chapter describes how to configure the properties of

More information

Media Resources CHAPTER

Media Resources CHAPTER CHAPTER 6 Last revised on: October 30, 2008 A media resource is a software-based or hardware-based entity that performs media processing functions on the data streams to which it is connected. Media processing

More information

Resource Reservation Protocol

Resource Reservation Protocol (RSVP) specifies a resource-reservation, transport-level protocol for reserving resources in IP networks. RSVP provides an additional method to achieve call admission control (CAC) besides location-based

More information

Music On Hold. Configuration Checklist for Music On Hold CHAPTER

Music On Hold. Configuration Checklist for Music On Hold CHAPTER CHAPTER 36 The integrated (MOH) feature allows users to place on-net and off-net users on hold with music that is streamed from a streaming source. The feature allows two types of hold: End-user hold Network

More information

Troubleshooting One Way Voice Issues

Troubleshooting One Way Voice Issues Troubleshooting One Way Voice Issues Document ID: 5219 Contents Introduction Prerequisites Requirements Components Used Conventions Problem Solutions Ensure That IP Routing Is Enabled on the Cisco IOS

More information

Call Control Discovery

Call Control Discovery CHAPTER 3 The call control discovery feature leverages the Service Advertisement Framework (SAF) network service, a proprietary Cisco service, to facilitate dynamic provisioning of inter-call agent information.

More information

Music On Hold. Configuration Checklist for Music On Hold CHAPTER

Music On Hold. Configuration Checklist for Music On Hold CHAPTER CHAPTER 36 The integrated (MOH) feature allows users to place on-net and off-net users on hold with music that is streamed from a streaming source. The feature allows two types of hold: End-user hold Network

More information

Configure Voice and Video Communication

Configure Voice and Video Communication s for On-Premises Deployments, page 1 for Cloud-Based Deployments, page 23 s for On-Premises Deployments Command or Action Purpose Install Cisco Options Package File for Devices, on page 2. Complete this

More information

TLS Setup. TLS Overview. TLS Prerequisites

TLS Setup. TLS Overview. TLS Prerequisites Setup Overview, page 1 Prerequisites, page 1 Configuration Task Flow, page 2 Interactions and Restrictions, page 8 Overview Transport Layer Security () provides secure and reliable signaling and data transfer

More information

examcollection.premium.exam.161q

examcollection.premium.exam.161q 300-075.examcollection.premium.exam.161q Number: 300-075 Passing Score: 800 Time Limit: 120 min File Version: 6.0 300-075 Implementing Cisco IP Telephony & Video, Part 2 v1.0 Version 6.0 Exam A QUESTION

More information

IPv6 Deployment Guide for Cisco Collaboration Systems Release 12.1

IPv6 Deployment Guide for Cisco Collaboration Systems Release 12.1 First Published: 2017-09-06 Last Modified: 2018-07-02 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387)

More information

BT SIP Trunk Configuration Guide

BT SIP Trunk Configuration Guide CUCM 9.1 BT SIP Trunk Configuration Guide This document covers service specific configuration required for interoperability with the BT SIP Trunk service. Anything which could be considered as normal CUCM

More information

This chapter provides information about Cisco Unified Communications Manager trunk configuration.

This chapter provides information about Cisco Unified Communications Manager trunk configuration. Trunk setup This chapter provides information about Cisco Unified Communications Manager trunk configuration. About trunk setup, page 1 Find trunk, page 57 Set up trunk, page 57 Delete trunk, page 59 Reset

More information

Cisco CTL Client Setup

Cisco CTL Client Setup This chapter provides information about Cisco CTL client setup. About, page 2 Addition of Second SAST Role in the CTL File for Recovery, page 2 Cluster Encryption Configuration Through CLI, page 3 Remove

More information

Media Resources CHAPTER

Media Resources CHAPTER 17 CHAPTER Revised: April 30, 2013; A media resource is a software-based or hardware-based entity that performs media processing functions on the data streams to which it is connected. Media processing

More information

Cisco Unified Communications Manager Trunks

Cisco Unified Communications Manager Trunks CHAPTER 2 A trunk is a communications channel on Cisco Unified Communications Manager (Cisco Unified CM) that enables Cisco Unified CM to connect to other servers. Using one or more trunks, Cisco Unified

More information

PrepAwayExam. High-efficient Exam Materials are the best high pass-rate Exam Dumps

PrepAwayExam.   High-efficient Exam Materials are the best high pass-rate Exam Dumps PrepAwayExam http://www.prepawayexam.com/ High-efficient Exam Materials are the best high pass-rate Exam Dumps Exam : 642-447 Title : Implementing Cisco Unified Communications Manager, Part 1 Vendor :

More information

Trace. Trace. Trace, page 1 Configure trace, page 4

Trace. Trace. Trace, page 1 Configure trace, page 4 , page 1 Configure trace, page 4 Cisco Unified Serviceability provides trace tools to assist you in troubleshooting issues with your voice application. Cisco Unified Serviceability supports SDI (System

More information

Configure Service Parameters

Configure Service Parameters Service Parameters Overview, page 1 Service Parameters Configuration Task Flow, page 1 Service Parameters Overview Each Cisco Unified Communications Manager node has a list of services that are available

More information

Test-king. Number: Passing Score: 800 Time Limit: 120 min File Version:

Test-king.  Number: Passing Score: 800 Time Limit: 120 min File Version: 300-075 Test-king Number: 300-075 Passing Score: 800 Time Limit: 120 min File Version: 14.1 http://www.gratisexam.com/ 300-075 Implementing Cisco IP Telephony & Video, Part 2 v1.0 Version 14.1 Exam A QUESTION

More information

Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2)

Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) Cisco 300-075 Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) https://killexams.com/pass4sure/exam-detail/300-075 QUESTION: 90 An engineer is configuring a new DX-80 in Cisco Unified Communications

More information

Device Support. Supported Devices

Device Support. Supported Devices This chapter provides general information about how Cisco Unified Communications Manager interacts with Cisco Unified Communications devices in your network. Supported Devices, page 1 Device Configuration

More information

AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide. Issue /3/2008

AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide. Issue /3/2008 AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide Issue 2.17 3/3/2008 Page 1 of 49 TABLE OF CONTENTS 1 Introduction... 4 2 Special Notes... 4 3 Overview...

More information

Telephony Integration

Telephony Integration Introduction, page 1 Phone System, page 2 Port, page 5 Port Group, page 6 Trunk, page 12 Speech Connect Port, page 13 Audio and Video Format Using Phone, page 14 Security, page 15 IPv6 in Unity Connection

More information

This chapter provides information about using Cisco Unified Communications Manager for working with and configuring Cisco gateways.

This chapter provides information about using Cisco Unified Communications Manager for working with and configuring Cisco gateways. This chapter provides information about using Cisco Unified Communications Manager for working with and configuring Cisco gateways. About gateway setup, page 1 Gateway reset, page 2 Gateway deletion, page

More information

Configuring Authentication and Encryption for CTI, JTAPI, and TAPI

Configuring Authentication and Encryption for CTI, JTAPI, and TAPI CHAPTER 22 Configuring Authentication and Encryption for CTI, JTAPI, and TAPI This chapter provides a brief overview of how to secure the CTI, JTAPI, and TAPI applications. It also describes the tasks

More information

Cisco IP Communicator Deployment Preparation

Cisco IP Communicator Deployment Preparation This chapter describes the required and recommended tasks for deploying Cisco IP Communicator. It also provides instructions for adding Cisco IP Communicator devices to the Cisco Unified Communications

More information

Preparing to Deploy Cisco IP Communicator

Preparing to Deploy Cisco IP Communicator CHAPTER 2 Revised: 1/19/11 This chapter describes the required and recommended tasks for deploying Cisco IP Communicator. It also provides instructions for adding Cisco IP Communicator devices to the Cisco

More information

DEMO QUESTION 1 An engineer is performing an international multisite deployment and wants to create an effective backup method to access TEHO destinat

DEMO QUESTION 1 An engineer is performing an international multisite deployment and wants to create an effective backup method to access TEHO destinat Vendor: Cisco Exam Code: 300-075 Exam Name: Implementing Cisco IP Telephony & Video, Part 2(CIPTV2) Version: Demo DEMO QUESTION 1 An engineer is performing an international multisite deployment and wants

More information

IM and Presence Service Network Setup

IM and Presence Service Network Setup Configuration changes and service restart notifications, page 1 DNS Domain Configuration, page 2 IM and Presence Service Default Domain Configuration, page 6 IM Address Configuration, page 7 Domain Management

More information

Configure Conference Bridges

Configure Conference Bridges Conference Bridges Overview, page 1 Conference Bridge Types, page 1 Call Preservation, page 4 Call Preservation Scenarios, page 5 Conference Bridge Configuration Task Flow, page 7 Conference Bridges Overview

More information

Configuring Multi-Tenants on SIP Trunks

Configuring Multi-Tenants on SIP Trunks The feature allows specific global configurations for multiple tenants on SIP trunks that allow differentiated services for tenants. allows each tenant to have their own individual configurations. The

More information

Setting Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection

Setting Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection Up a Mitel SX-2000 Digital PIMG Integration, page 1 Up a Mitel SX-2000 Digital PIMG Integration Task List for Mitel SX-2000 PIMG

More information

Configure Core Settings for Device Pools

Configure Core Settings for Device Pools Device Pools Overview Device Pools Overview, on page 1 Device Pool Prerequisites, on page 7 Core Settings for Device Pools Configuration Task Flow, on page 7 Device pools provide a common set of configurations

More information

Q&As. Implementing Cisco Collaboration Devices v1.0. Pass Cisco Exam with 100% Guarantee

Q&As. Implementing Cisco Collaboration Devices v1.0. Pass Cisco Exam with 100% Guarantee 210-060 Q&As Implementing Cisco Collaboration Devices v1.0 Pass Cisco 210-060 Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: 100% Passing Guarantee 100% Money Back

More information

Settings. IP Settings. Set Up Ethernet Settings. Procedure

Settings. IP Settings. Set Up Ethernet Settings. Procedure This chapter provides information about using the options to display and change IP settings, host settings, and Network Time Protocol (NTP) settings. IP, page 1 Set Up NTP Servers, page 4 Set Up SMTP,

More information

Unified Border Element (CUBE) with Cisco Unified Communications Manager (CUCM) Configuration Example

Unified Border Element (CUBE) with Cisco Unified Communications Manager (CUCM) Configuration Example Unified Border Element (CUBE) with Cisco Unified Communications Manager (CUCM) Configuration Example Document ID: 99863 Contents Introduction Prerequisites Requirements Components Used Conventions Configure

More information

Phone template. Add phones to database. Procedure

Phone template. Add phones to database. Procedure Cisco Unified Communications Manager Bulk Administration (BAT) gives the administrator a fast and efficient way to add, update, or delete large numbers of phones in batches, rather than performing individual

More information

Deploy Webex Video Mesh

Deploy Webex Video Mesh Video Mesh Deployment Task Flow, on page 1 Install Webex Video Mesh Node Software, on page 2 Log in to the Webex Video Mesh Node Console, on page 4 Set the Network Configuration of the Webex Video Mesh

More information

CCVP CIPT2 Quick Reference

CCVP CIPT2 Quick Reference Introduction...3...4 Centralized Call Processing Redundancy...11 CCVP CIPT2 Quick Reference Bandwidth Management and Call Admission Control...17 Applications for Multisite Deployments...21 Security...31

More information

Implementing Cisco Unified Communications Manager Part 2, Volume 1

Implementing Cisco Unified Communications Manager Part 2, Volume 1 Implementing Cisco Unified Communications Manager Part 2, Volume 1 Course Introduction Learner Skills and Knowledge Course Goal and Course Flow Additional Cisco Glossary of Terms Your Training Curriculum

More information

Call Back supports Suspend/Resume CallBack notification for both intracluster and intercluster QSIG

Call Back supports Suspend/Resume CallBack notification for both intracluster and intercluster QSIG Overview, page 1 Prerequisites, page 1 Configuration Task Flow, page 2 Interactions and Restrictions, page 8 Troubleshooting, page 9 Overview The CallBack feature allows you to receive notification when

More information

Cisco CTL Client setup

Cisco CTL Client setup Cisco CTL Client setup This chapter provides information about Cisco CTL client setup. About Cisco CTL Client setup, page 2 Remove etoken Run Time Environment 3.00 for CTL Client 5.0 plug-in, page 2 Cisco

More information

Cisco ATA 191 Analog Telephone Adapter Overview

Cisco ATA 191 Analog Telephone Adapter Overview Cisco ATA 191 Analog Telephone Adapter Overview Your Analog Telephone Adapter, page 1 Your Analog Telephone Adapter The ATA 191 analog telephone adapter is a telephony-device-to-ethernet adapter that allows

More information

Setup for Cisco Unified Communications Manager

Setup for Cisco Unified Communications Manager Setup for Cisco Unified Communications Manager This chapter describes how you can set up Cisco Jabber for ipad using Cisco Unified Communications Manager. System and Network Requirements, page 1 Recommended

More information

Cisco - CMA v8.5 Communications Manager Administration

Cisco - CMA v8.5 Communications Manager Administration Course Overview View Course Dates & Register Today Communications Manager Administration (CMA) v8.5 provides system administrators and networking professionals with an understanding of the Cisco Unified

More information

Cisco DSP Resources for Transcoding Conferencing and MTP

Cisco DSP Resources for Transcoding Conferencing and MTP Cisco DSP Resources for Transcoding Conferencing and MTP This chapter provides information about how Cisco digital signal processor (DSP) resources are used for transcoding and conferencing. The modules,

More information

Customer Guide to Cisco JTAPI- BiB Integrations. March

Customer Guide to Cisco JTAPI- BiB Integrations. March Customer Guide to Cisco JTAPI- BiB Integrations March 2017 www.incontact.com Introduction Customer Guide to Cisco JTAPI-BiB Integrations Version: This guide should be used with NICE Uptivity (formerly

More information

Setting up Alcatel 4400 Digital PIMG Integration

Setting up Alcatel 4400 Digital PIMG Integration up Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection, on page 1 Up an Alcatel 4400 Digital PIMG Integration with

More information

Hold Reversion. Configuration Checklist for Hold Reversion CHAPTER

Hold Reversion. Configuration Checklist for Hold Reversion CHAPTER CHAPTER 25 The hold reversion feature alerts a phone user when a held call exceeds a configured time limit. This chapter provides information on the following topics: Configuration Checklist for, page

More information

Setting Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection

Setting Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection up Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection, page 1 Up an Alcatel 4400 Digital PIMG Integration with Cisco

More information

CISCO EXAM QUESTIONS & ANSWERS

CISCO EXAM QUESTIONS & ANSWERS CertifyMe Number: 642-427 Passing Score: 800 Time Limit: 120 min File Version: 29.0 http://www.gratisexam.com/ CISCO 642-427 EXAM QUESTIONS & ANSWERS Exam Name: TVOICE v8.0 Troubleshooting Cisco Unified

More information

Cisco Unified CME Commands: M

Cisco Unified CME Commands: M Cisco Unified CME Commands: M mac-address (ephone), page 3 mac-address (voice-gateway), page 5 mailbox-selection (dial-peer), page 7 mailbox-selection (ephone-dn), page 9 max-calls-per-button, page 11

More information

SBC Site Survey Questionnaire Forms

SBC Site Survey Questionnaire Forms SBC Site Survey Questionnaire Forms For Design and Deployment of AudioCodes Mediant SBC Product Line This document is intended for the persons responsible for the design and deployment of AudioCodes SBC

More information

Cisco TelePresence Conductor with Cisco Unified Communications Manager

Cisco TelePresence Conductor with Cisco Unified Communications Manager Cisco TelePresence Conductor with Cisco Unified Communications Manager Deployment Guide XC2.2 Unified CM 8.6.2 and 9.x D14998.09 Revised March 2014 Contents Introduction 4 About this document 4 Further

More information

Configure TFTP Servers

Configure TFTP Servers Proxy TFTP Deployment Overview, on page 1 TFTP Server Configuration Task Flow, on page 3 Proxy TFTP Deployment Overview Use a proxy Trivial File Transfer Protocol (TFTP) server to provide the configuration

More information

Model Information, Status, and Statistics

Model Information, Status, and Statistics Overview, page 1 Display Model Information Screen, page 1 Status Menu, page 2 Overview This chapter describes how to use the following menu and screen on the Cisco Unified IP Phone 7931G to view model

More information

TCP and UDP Port Usage Guide for Cisco Unified Communications Manager, Release 10.0(1)

TCP and UDP Port Usage Guide for Cisco Unified Communications Manager, Release 10.0(1) and UDP Port Usage Guide for Cisco, Release 10.0(1) First Published: December 03, 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel:

More information

Cisco Unified Survivable Remote Site Telephony Version 7.1

Cisco Unified Survivable Remote Site Telephony Version 7.1 Survivable Remote Site Telephony Version 7.1 Communications Solutions unify voice, video, data, and mobile applications on fixed and mobile networks, enabling easy collaboration every time from any workspace.

More information

AT&T IP Flexible Reach And IP Toll Free Cisco Call Manager Configuration Guide. Issue /5/2007

AT&T IP Flexible Reach And IP Toll Free Cisco Call Manager Configuration Guide. Issue /5/2007 And IP Toll Free Cisco Call Manager Configuration Guide Issue 2.13 6/5/2007 Page 1 of 38 TABLE OF CONTENTS 1 Introduction... 3 2 Special Notes... 3 3 Overview... 4 3.1 Call Manager Site... 4 3.2 TFTP and

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Configuring SIP trunks between Avaya Aura Session Manager Release 6.2, Avaya Meeting Exchange Enterprise Edition Release 6.2 and Cisco Unified Communications

More information

PASS4TEST. IT Certification Guaranteed, The Easy Way! We offer free update service for one year

PASS4TEST. IT Certification Guaranteed, The Easy Way!   We offer free update service for one year PASS4TEST IT Certification Guaranteed, The Easy Way! \ http://www.pass4test.com We offer free update service for one year Exam : 642-444 Title : IP Telephony Exam (CIPT) Vendors : Cisco Version : DEMO

More information

Cisco Unified MeetingPlace Integration

Cisco Unified MeetingPlace Integration CHAPTER 14 This chapter covers system-level design and implementation of Cisco Unified MeetingPlace 5.4 in a Cisco Unified Communications Manager 5.x environment. The following aspects of design and configuration

More information

TVOICE: Troubleshooting Cisco Unified Communications v8

TVOICE: Troubleshooting Cisco Unified Communications v8 Course Objectives Describe a systematic methodology to troubleshoot Cisco Unified Communications solutions Isolate and troubleshoot reported issues that relate to Cisco Unified Communications Manager.

More information

Multicast Music-on-Hold Support on Cisco UBE

Multicast Music-on-Hold Support on Cisco UBE First Published: July 22, 2011 Last Updated: July 22, 2011 The Multicast Music-on-Hold (MMOH) feature enables you to subscribe to a music streaming service when you are using a Cisco Unified Border Element.

More information