IN CEILING DUAL BAND ACCESS POINT/ ROUTER 750MBPS WL-ICDBG24-051

Transcription

1 IN CEILING DUAL BAND ACCESS POINT/ ROUTER 750MBPS WL-ICDBG USER MANUAL

2 REV

3 Thanks for choosed our product INDEX General Warning CHAPTER 1 Hardware and Operation mode Instruction 1.1 LED indicator 1.2 AP Interface 1.3 Power Supply PoE Adapter Power Supply Powered by PoE Switch 1.4 Operation Mode Wirelss AP Wirelss Repeater Gateway 1.5 Connect Wireless AP with PC CHAPTER 2 Login CHAPTER 3 Quickly Configure Wireless AP 3.1 Gateway Mode 3.2 WiFi Repeater and Station operation configuration 3.3 AP Operation mode 3.4 WISP Operation mode 3.5 Advanced Setting Device Status Ghz/5.8Ghz Wireless Setting Virtural AP Network setting Management Share Internet and Obtain IP address automatically CHAPTER 4 Trouble Shooting CHAPTER 5 Declaration of conformity 3

4 4

5 General warnings Fasten the AP in the desired position, considering that as the device being installed is a radio device, the following simple rules must be observed: Avoid enclosing the appliance between two metal walls; The efficiency of radio transmission is reduced when there are obstacles, metal shelving or other objects that may block the reception of the radio signals; If the product is wall-mounted, fasten it to a masonry wall rather than a metal wall, to improve the range of the signal; Remember that the best position for the AP is one where it is visible to the other devices. It should be positioned in such a way as to minimize any obstacles; Like all radio equipment, avoid installing the AP near other electronic appliances so as to avoid interference; If the appliance is used in a way that is not described by the manufacturer, the specified level of protection may be affected. Do not install the instruments in environments with the following characteristics: - strong vibrations or knocks; - exposure to water sprays; - exposure to direct sunlight or the elements in general; 5

6 CHAPTER 1 HARDWARE AND OPERATION MODE INSTRUCTION 1.1 LED indicator Green: Power Indicator Blue: WiFi Indicator 1.2 AP Interface RST: Reset Button, it make AP revert to default data after press it 15 sec. WAN: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Wireless AP and WiFi Repeater operation mode LAN: Gigabit LAN Port to end users LED: LED Indicator of WAN port and LAN port DC: DC power connector 1.3 Power Supply PoE Adapter Power Supply The connection diagram, internet cable connect to PoE adapter s LAN Port, Ceiling AP s WAN port connect to PoE adapter s PoE Port, then PC will access into ceiling AP through cable or wireless The PD wireless AP support 24V PoE, so PoE adapter should be 24V PoE. 6

7 1.3.2 Powered by PoE Switch The connection diagram, Internet cable from PoE Switch to Ceiling AP s WAN Port, then PC access into ceiling AP wired/wireless. Pls notevthe PD wireless AP support 24V PoE, m the PoE switch should comply with 24V PoE. 1.4 Operation Mode There are three operation mode on this wireless AP: Wirelss AP Plug&Play to transmit wireless signal for wireless and users from wired networking. 7

8 1.4.2 Wirelss Repeater Wireless receiver and transmit, to extend the existing wireless networking for more range Gateway Supply WAN connection from DSL, Cable MOdem or broadband mobile phone network through PPPoE, Static, IP, Dynamic IP. 8

9 1.5 Connect Wireless AP with PC Use can connect the PC with wireless AP by Wireless SSID and LAN cable: The diagram of wireless connection showed as follow: Pls note: the default SSID is MachPower2.4G/MachPower5G, SSID s password is The diagram of LAN cable connection showed as follow: CHAPTER 2 LOGIN 1. Connect the Ceiling AP with computer 2. Configure the PC Configure the PC s local connection IP address as X (X is number from 2 to 254), subnet mask is , follow the next image. 9

10 3. Input into IE browser, then pop up the login page, the default login user name: admin, Passwords: admin, pls do following the next image 4. After login, then Device Status will be showed; This page will show the AP s default operation mode, channel, connection status, CPU usage, Wireless settings, LAN Setting, AP s Loca- 10

11 tion, CPE s hardware/firmware version CHAPTER 3 QUICKLY CONFIGURE WIRELESS AP 3.1 Gateway Mode Click Gateway Mode under following picture and choose the right WAN access type, then input the right SSID, Channel, key as like. 11

12 ù 3.2 WiFi Repeater and Station operation configuration A. Login the Web management page, click Repeater Mode, then Scran AP B. Select the AP s SSID want to bridge, take TEST2.4G for example. 12

13 If your computer can t pop up this window, pls check your IE explorer and see whether it is blocked already. And if this Wireless AP can t scan any SSID, pls check if there are 5G wireless signal. C. input the AP s key, and apply changes 3.3 AP Operation mode Choose the AP operation mode, AP Location as well as the wireless basic settings for the 2.4Ghz and 5.8Ghz, Then apply; 13

14 3.4 WISP Operation mode Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on the stepes showed in picture: Then the device were in WISP mode, users can check the details under status; 14

15 3.5 Advanced Setting In advanced setting, user can check the ceiling AP s firmware version, working status, 2.4G/5.8Ghz wireless, LAN Status, upgrade firmware, Reset Device Status This page will show basic parameters for this unit, like firmware version,hardware version,etc; Ghz/5.8Ghz Wireless Setting On this page, users can configure the basic wireless settings freely Virtural AP There are 3 virtural AP in 2.4Ghz and 5.8Ghz individually, (total 6 virtal AP), if need virtural SSID, then users can configure basic settings 15

16 showed in following picture: Network setting In this page, users can set up the basic LAN setting 16

17 3.5.5 Management In this part, show the system time, Logs, upgrade firmware, system, user info. And we show System time, how to upgrade firmware, as well as Log-in username/password modification; 17

18 3.5.6 Share Internet and Obtain IP address automatically Set computer s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed. the computer will obtain the IP address from router or base station to get Internet. 18

19 CHAPTER 4 TROUBLE SHOOTING The Failure phenomenon and solution Failure phenomenon SYS Indicator off Can t land to Wireless AP through Web page Solution Pls make sure the PoE module connection is right. POE Port connect with AP, LAN port connect with computer Pls check the IP address of computer and Wireless AP to see whether they are in same networking segment, The method is click start - Run input cmd,ping to test the Wireless AP connectivity. Reset Wireless AP and load it again; Pls make sure the IP address is not occupied by other device in Wireless AP s networking; Check computer and cable problem, recommend to use 10/100M UTP unshielded cable; Clean up Arp binding from Start - Run input cmd arp d Clean the IE Brower s temporary files and Cache file; 19

20 Wireless AP can t connect with AP (the status display unconnected) Try to scan the avaliable wireless networking again; Make sure the Wireless AP s wireless standard is correct; (2.4Ghz signal should connect 2.4Ghz, 5.8Ghz signal should connect 5.8Ghz signal); The Security and passwords are matched between Wireless AP and AP; The signal strength of AP is too weak to connect, should be more than -75dBm; Can t scan the wireless AP The connection of Wireless AP and AP is success, but the computer can t share internet How to Reset Wireless AP Scan it several times more; If using 5Ghz to scan, please make sure there are 5G signal existed. Reset the Wireless AP, scan it again after Wireless AP restart; Pls Check the computer s IP address and DNS setting. If it is dynamin, set the network card as automatically obtain. If it is static IP, pls contact with ISP for correct IP address and DNS address. Press the Reset button more than 15 seconds after power on. The Wireless AP will restore factory default after the Wireless AP restart. 20

21 CHAPTER 5 DECLARATION OF CONFORMITY RoHS It is stated that the construction materials used in our products comply with the requirements of Directive 2011/65 / EU (RoHS). CE Declaration of Conformity Compliance with European Directives The product complies with the requirements of the Low Voltage Directive (Safety) 2014/35 / EU and subsequent amendments. Disposal of the Product The product can not be disposed of as urban waste, but it must be collected separately; Any violation shall be punishable by monetary sanctions in accordance with current regulations. Improper disposal of the product, or misuse of the product itself or parts thereof, is harmful to the environment and to human health. Correct disposal of the products bearing the symbol of the bin marked by a cross helps to avoid possible negative consequences for the environment and human health. 21

22 FCC This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits have been developed to ensure reasonable protection against harmful interference in domestic installations. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. It is not excluded that this may also occur in particular installation types. In the event of interference with the reception of the radio or television signal, which can be detected by switching the device off and on again, you are invited to complete one or more of the following procedures: Reorient or reposition the receiving antenna. Increase the distance between the receiver and the equipment. Connect the equipment to a circuit other than the one to which the receiver is connected. Consult your dealer or an experienced radio / TV technician for assistance. 22

23

24 24 Mach Power is a registered trademark All Rights Reserved > visit our website