Backbone network technologies. T Jouni Karvo, Timo Kiravuo
|
|
- Dwayne Barnett
- 6 years ago
- Views:
Transcription
1 Backbone network technologies T Jouni Karvo, Timo Kiravuo
2 Backbone network technologies This lecture tells about backbone networks After this lecture, you should know WDM, PDH, SDH and ATM understand how virtual overlay networks can be created in the physical network understand how lower layer techniques make both telephone and data networks possible to coexist in the same network
3 Multiplexing There are several multiplexing techniques that allow simultaneous transmissions in the same physical medium: TDM (Time Division Multiplexing) FDM (Frequency Division Multiplexing) WDM (Wavelength Division Multiplexing) of these, FDM is not in widespread use in modern backbone networks (but is in radio networks) TDM can be used in any layer, not only on the physical layer
4 WDM WDM is essentially FDM, but deserves a new name, since it is implemented by using lasers of different colors: Due to the physical properties of light, signals of different wavelengths do not interfere significantly Up to 160 wavelengths (DWDM, Dense Wavelength Division Multiplexing) and growing with UDWDM (Ultra- Dense WDM) Each wavelength can carry e.g. 10Gb/s with SDH leading to 1.6Tbps speeds per optical fiber in DWDM Compare this to telephone calls; if all 5 million Finns would call simultaneously to a foreign destination, it would result only in 0.32Tbps!
5 WDM switching Switching: electro-optical or purely optical optical equipment; for example Micro-Electro Mechanical System (MEMS) switches, where wavelengths are first separated by prisms and then switched by adjustable mirrors Add-Drop Multiplexers (ADM) are equipment that are used to add or drop specific wavelengths from the line without affecting the other wavelengths. Optical Cross Connects (OXC) are optical switches, able to route incoming wavelengths to specific outgoing ports. Care must be taken to avoid joining similar wavelengths Each wavelength can be modulated and transmitted separately There is no need to use a single protocol
6 Virtual Topologies Virtual topologies can be created over the physical one. Enables more flexible service offerings Care should be taken to provide sufficient redundancy
7 A peek in history In order to understand SDH and ATM properly, knowledge on PDH is essential. PDH was the means to make the telephone network digital in the 60s. These techniques are used in the core networks of the operators, to provide high capacity links. These techniques are very similar; the essential difference is in synchronization and framing.
8 PCM frames (E1/T1) Speech is transmitted as PCM (Pulse Code Modulation) frames. The speech is converted to 8bit (7bit in USA) digital samples 8000 times in second. Can transmit speech up to 4kHz (Nyquist theorem) A-law or?-law coding After that, the network treats it simply as a binary data stream. One speech channel has a data rate of 64 kbps (or 56 kbps in USA). Any other data can be treated similarly E.g. IP packets may be sent consecutively as a data stream of 64 kbps. Since the trunk lines use TDM for transmitting multiple channels simultaneously, the data streams are cut in octets, and framed
9 Time Slots The European E1 frame contains 32 channels A channel is an endless stream of data octets 2 channels transmit control information and 30 data The frames contain 32 octets, called timeslots (TS) TS0 TS1... TS14 TS15 TS16... TS31 TS0 contains synchronizing code, notifying the receiver of the beginning of the frame. TS1--TS15 contain speech (or data) channels TS16 contains signaling TS17--TS31 contain speech (or data) channels.
10 PDH Frames One frame thus contains one octet of each of the carried channels. A frame is transmitted 8000 times each second, yielding a 8 * 32 * 8000 = bps or Mbps. The corresponding T1 frame used in USA contains 24 speech channels with 8-bit coding and one framing bit, ``stealing'' payload bits for signaling. The frame length is 193bits, sent 8000 times a second, yielding a Mbps data rate. A multi-frame is a series of consecutive frames (16 in Europe. 12 in USA). Multi-frames are used, since for modern equipment, it is not necessary to tell the receiver every time where the frame starts. Instead, space is given for CRC codes and extra signaling.
11 PDH Synchronization All digital switches have a master clock. All outgoing streams are slaves of the master clock. Incoming bit streams are slaves of their senders' clocks. For proper transmission, clocks need to be synchronized. Consider a sender A sending its stream a bit faster than the relaying node B can forward it to the receiver C. At some point, the buffers at B overflow, causing a lost PCM frame. This is called a slip. The difference of PDH and SDH is their synchronization and frame structure.
12 Plesiochronous Digital Hierarchy (PDH) In plesiochronous operation the nodes are synchronized on the E1 (T1)-level. Synchronization sources send the E1 multiplex using their high precision clocks and the receivers synchronize themselves according to the input signal Both mutual synchronization and master-slave synchronization modes possible. High precision clock means here a clock with a stability range of about [10^ ^-13], implying use of atomic clocks, possibly UTC or GPS coordinated.
13 PDH multiplexes A PDH multiplex is means a bunch of primary PCM multiplexes (E1 or T1). In a plesiochronous system, each PCM multiplex is transmitted with a different clock. The E1 level clocks are synchronized, but higher levels synchronize according to the E1 level. Since the actual transmission rates differ a little from the nominal bit rate, some action is needed to compensate the differences in different streams. The solution used is justification (called stuffing in USA). Justification means adding extra bits to the stream, which allows for reading of an input buffer faster than the sender fills it.
14 PDH hierarchy a) E1 b) E2 c) E3 d) E4 The first PDH multiplex level is E1, containing (as noted before, 30 channels and 2 control channels), Mbps. The second PDH multiplex level is E2, containing four E1 multiplexes (120channels). The bit rate is Mbps, containing frames of 1056bits, (4 * 256 bits for the multiplexes and 4 * 8 bits for justification and frame alignment). The third PDH multiplex level, E3 contains four E2 multiplexes (called tributaries), yielding 480 channels. The bit rate is Mbps. The fourth PDH multiplex level, E4 contains four E3 multiplexes (1920 channels), with bit rate of Mbps.
15 PDH Hierarchy cont. Note that for each multiplex level, the frame rate is 8000 frames/second, i.e. the same as for E1! Sometimes synchronization errors are too big to be corrected and a slip occurs. In these cases a frame is either lost or re-sent. In speech communications this might cause a small rustle for all channels transmitted on the link. For data communications, one octet is lost or duplicated for all channels on the link. This might result a lost packet or even connection on the application level. PDH is being replaced by SDH (and in Finland already mostly gone).
16 Synchronous Digital Hierarchy SDH is a timing hierarchy Allows higher and more flexible bit-rates than PDH Uses a different frame structure and synchronization STS (Am. called Sonet) or STM (Euro) frame structure SDH is used to synchronize the frames Hierarchical synchronization Nodes on a higher level on hierarchy are used to synchronies the lower levels. One master clock to synchronize whole operator network More accurate synchronization reduces slippage
17 SDH STM Frame structure The basic SDH frame, STM-1 contains 2430 octets, and is transmitted once in each 125 microseconds, i.e times a second. This yields a Mbit/s gross bit rate. a) 270 octets b) 9 rows c) 9 octets d) 261 octets e) 9 rows f) AU g) SOH AU = Administrative Unit (payload) SOH = Section Overhead
18 Frame Structure cont. Higher order SDH frames, STM-N contain N interleaved STM-1 payloads, and a N times the transport overhead. Again, 8000 frames are sent each second. Typical STM-N multiplexes include STM-4 at Mbit/s, STM-16 at Mbit/s, STM-64 at Mbit/s. Synchronization errors are handled by AU-Pointers. The AU may float within the frames: a) Frame N b) Frame N+1 c) AU-Ptr d) AU (payload)
19 Frame Structure cont. In addition to AU-Pointers, three octets of STM-1 SOH can be used for justification. The AU in is then further divided to smaller containers capable of accommodating different bandwidth tributaries. (this makes SDH able to carry many types of lower level multiplexes simultaneously) The data rates of the lowest level containers in an AU are: kbit/s, kbit/s, kbit/s, kbit/s, kbit/s, and kbit/s. I.e. both E1 and T1 PCM multiplexes are compatible with SDH.
20 SDH Synchronization There are four possible synchronization modes in a SDH network: Synchronous --- all elements are synchronized (possibly indirectly) to the PRC. Normal operation. Pseudo-synchronous --- all elements are synchronized to a PRC, but there are several PRC:s. Normal operation on links between operators. Plesiochronous --- Part of the nodes have lost their synchronization reference, and work on hold-over. Asynchronous --- Nodes are on free run. Due to possible float and plesiochronous operation, also SDH needs justification, but is is implemented differently than in PDH.
21 SDH synchronization levels US terminology: stratum, pl. strata Primary Reference Clock (PRC, Stratum 1) requirements in ITU-T G.811 relative error <10^-11. For example cesium clocks. free running, but may be co-ordinated by UTC One per operator Transit Synchronization Supply Unit (Transit SSU, ~ Stratum 2) requirements in ITU-T G.812-T relative error in holdover: <10^-9 e.g. rubidium clocks stable enough for short periods of holdover operation (operation without synchronization reference from PRC)
22 SDH synchronization levels cont. Local Synchronization Supply Unit (~ Stratum 3) requirements in ITU-T G.812-L relative error in holdover: <2 * 10^-8 e.g. temperature compensated crystals reduced holdover capabilities local switches SDH Equipment Clock (SEC) (~ Stratum 4) relative error in holdover: <10^-8 relative error in free run: 4.6 * 10^-6 local switches, digital channel banks and private exchanges
23 Clock adjustment Clocks on the higher levels on hierarchy give correction terms to adjust the clock speed.? clocks' frequencies float around the frequency given by the PRC.
24 Topology Rather free topology can be used Typically, SDH networks are organized as dual rings Backbones might be organized as meshes Rings are configured to be self-healing (in milliseconds) Digital Cross Connects (DXC) and Add-Drop Multiplexers used Section-Line-Path: Sections are between devices (such as signal regenerators) Line between multiplexers Path between terminals
25 Topology cont. SDH (or SONET in USA) is the Layer 2- transmission technology used mostly for telephone traffic, but also for the Internet backbones nowadays. Usage of SDH containers is ideal for creating a logical topology over the physical one. The approach for flexibility and high data rates in SDH works well, but is a bit complex at the frame level. Thus, a third approach, ATM.
26 Asynchronous Transfer Mode Instead of E1-frames (or T1-frames), ATM uses 53 octet frames, that are called cells. The payload of an ATM cell is 48 octets, i.e. that of 2 T1 multiplexes. Thus, a stream of ATM cells sent 8000 times a second could carry 48 simultaneous speech connections. In practice this is not done, but AAL transport is used instead. In PDH, each channel has its own timeslot which does not change. The same holds for higher order multiplexes. SDH uses pointers inside frames to show the location of the containers. ATM cells have the channel number (Virtual Path/Virtual Circuit identifier -- (VPI/VCI) L2 address) carried in each cell instead.
27 ATM cont. VPI/VCI can be used to create a logical topology over the physical one When creating higher order ATM multiplexes, there is no need for reframing data, or sending ATM cells a specific order, due to the Layer 2 address. The ATM network needs synchronization just as PDH and SDH networks. It can be synchronized using the same clock hierarchy as the SDH network. There is no justification capability in ATM, but due to the lack of frame structure, it is possible to drop single cells instead of whole higher order frames. The absence of frame structure also allows for variable bit rate virtual circuits (channels).
28 ATM cont. To take advantage of the increased flexibility, a new set of protocols was developed. The combination of ATM and these protocols is called B-ISDN. ATM will be used in 3rd generation mobile networks, so its importance might rise. Application ATM Adaptation Layer (AAL) ATM cell switching Physical layer
29 ATM cell switching services: Constant bit rate (CBR) --- stream service Variable bit rate (VBR) --- stream described by peak cell rate, sustainable bit rate, and maximum burst size. Available bit rate (ABR) --- the applications can renegotiate the bit rate with the network devices during the connection Unspecified bit rate (UBR) --- no QoS guarantees (cells are dropped by the network element if necessary)
30 ATM Adaptation Layer Segmentation and Reassembly (SAR) Different types of AAL: AAL1 supports CBR services (such as E1/T1) AAL2 for low bit rate packet traffic with end-to-end timing requirements AAL3/4 for bursts of data with no timing requirements. Two modes: message mode and stream mode AAL5 is like AAL3/4 but without sub-addressing SAAL (Signaling AAL) for reliable transfer of signaling messages
31 Summary of trunk links Telephone network is designed for streaming data Data networks have been designed using the experience in telephone network engineering Synchronization is essential PDH, SDH and ATM are a "family'' ATM offers a bit more flexibility than SDH. WDM adds capacity and logical topology SDH is currently the major transmission system, WDM increasingly popular
Backbone network technologies. T Jouni Karvo, Timo Kiravuo
Backbone network technologies T-110.300 Jouni Karvo, Timo Kiravuo Backbone network technologies This lecture tells about landline backbone networks After this lecture, you should know WDM, PDH, SDH and
More informationCommunication Networks
Communication Networks Chapter 3 Multiplexing Frequency Division Multiplexing (FDM) Useful bandwidth of medium exceeds required bandwidth of channel Each signal is modulated to a different carrier frequency
More informationSONET. By Sadhish Prabhu. Unit II
SONET By Sadhish Prabhu History Digital carrier systems The hierarchy of digital signals that the telephone network uses. Trunks and access links organized in DS (digital signal) hierarchy Problem: rates
More informationSynchronous Optical Networks SONET. Computer Networks: SONET
Synchronous Optical Networks SONET 1 Telephone Networks {Brief History} Digital carrier systems The hierarchy of digital signals that the telephone network uses. Trunks and access links organized in DS
More informationATM. Asynchronous Transfer Mode. (and some SDH) (Synchronous Digital Hierarchy)
ATM Asynchronous Transfer Mode (and some SDH) (Synchronous Digital Hierarchy) Why use ATM? Circuit switched connections: After initial setup no processing in network nodes Fixed bit rates, fixed time delay
More informationSynchronous Optical Networks (SONET) Advanced Computer Networks
Synchronous Optical Networks (SONET) Advanced Computer Networks SONET Outline Brief History SONET Overview SONET Rates SONET Ring Architecture Add/Drop Multiplexor (ADM) Section, Line and Path Virtual
More informationTelco Scalable Backbones
Telco Scalable Backbones PDH, SONET/SDH (C) Herbert Haas 2005/03/11 Everything that can be invented has been invented Charles H. Duell, commissioner of the US Office of Patents 1899 Agenda Basics Shannon
More informationBROADBAND AND HIGH SPEED NETWORKS
BROADBAND AND HIGH SPEED NETWORKS SYNCHRONOUS OPTICAL NETWORK (SONET) Synchronous Optical Network (SONET) is a standard for optical telecommunications transport. SONET defines optical carrier (OC) levels
More informationTransport Network Technologies
Course 34310 Introduction to Communication Technology Course 34311 Introduction to Networks for Telecommunication and Data Communication Transport Network Technologies October 23, 2010 Lars Staalhagen
More information! Cell streams relating to different media types are multiplexed together on a statistical basis for transmission and switching.
Asynchronous Transfer Mode (ATM) Networks! All source media is first broken down into a stream of fixed sized units known as cells.! Cell streams relating to different media types are multiplexed together
More informationFor internal circulation of BSNL only
E3-E4 E4 (CFA) Overview of SDH AGENDA SDH & PDH Hierarchy SDH Network Survivability Synchronous All elements are synchronized with one master clock. DIGITAL Information is in binary. SDH OVERVIEW HIERARCHY
More informationChapter 8: Multiplexing
NET 456 High Speed Networks Chapter 8: Multiplexing Dr. Anis Koubaa Reformatted slides from textbook Data and Computer Communications, Ninth Edition by William Stallings, 1 (c) Pearson Education - Prentice
More informationlearntelecoms interactive e-learning suite of courses: SyncNet v6 SDH-based broadband networks SyncNet
Tel: 0845 0949 120 Email: info@ptt.co.uk Web site: www.ptt.co.uk SyncNet SyncNet v6 SDH-based broadband networks SyncNet is a suite of interactive, multimedia e-learning courses. provides training in the
More informationmultiplexing hierarchies
Transmission techniques and multiplexing hierarchies Switching Technology S38.165 http://www.netlab.hut.fi/opetus/s38165 2-1 Transmission techniques and multiplexing hierarchies Transmission of data signals
More informationNetwork Topologies & Error Performance Monitoring in SDH Technology
Network Topologies & Error Performance Monitoring in SDH Technology Shiva Sharma Electronics and Communications Department Dronacharya College of Engineering Gurgaon, Haryana Shiva.92@hotmail.com Abstract
More informationWhat is SDH? Telecommunications Standards Primer. Plesiochronous Digital Hierarchy (PDH) Limitations of PDH Network
Página 1 de 7 Telecommunications Standards Primer What is SDH? This document is intended as an introductory guide to the Synchronous Digital Hierarchy (SDH) standard. The following is a representative
More informationTDM Techniques. Time Division Multiplexing (synchronous, statistical) Telco Backbones (Digital Voice Transmission, PDH, SDH)
TDM Techniques Time Division Multiplexing (synchronous, statistical) Telco Backbones (Digital Voice Transmission, PDH, SDH) Agenda Introduction Synchronous (Deterministic) TDM Asynchronous (Statistical)
More informationChapter 4 Transmission Systems and the Telephone Network. School of Info. Sci. & Eng. Shandong Univ.
Chapter 4 Transmission Systems and the Telephone Network School of Info. Sci. & Eng. Shandong Univ. Skip in Chapter 3 Articles 3.8.7, 3.8.8 (polynomial math for CRC codes) Skip in Chapter 4 4.2.2 (SONET
More informationTransmission Technology Ses SDH
Transmission Technology Ses SDH ALTTC/TX1/SDH/CONCEPTS 1 CONTENTS SDH PROTECTION PLANNING SYNCHRONISATION ALTTC/TX1/SDH/CONCEPTS 2 SDH: DISCUSSION AREA WHAT IS SDH? EVOLUTION DRIVING FORCES LIMITATIONS
More informationPHYSICAL LAYER TIMING
PHYSICAL LAYER TIMING Physical Layer Timing Timing in TDM Networks Synchronous Multiplexing (TDM) Transferring Timing (Timing Distribution) Stratum Levels Slips Asynchronous Multiplexing (TDM) Timing in
More informationLecture 2 Physical Layer - Multiplexing
DATA AND COMPUTER COMMUNICATIONS Lecture 2 Physical Layer - Multiplexing Mei Yang Based on Lecture slides by William Stallings 1 MULTIPLEXING multiple links on 1 physical line common on long-haul, high
More informationMaster Course Computer Networks IN2097
Chair for Network Architectures and Services Prof. Carle Department of Computer Science TU München Master Course Computer Networks IN2097 Prof. Dr.-Ing. Georg Carle Christian Grothoff, Ph.D. Stephan Günther
More informationApplication Note. Re-timing: Cost-effective Synchronization via Re-timed E1 and DS1 Signals. Precision, Stability, Innovation, Support.
Re-timing: Cost-effective Synchronization via Re-timed E1 and DS1 Signals Application Note Number 14 TELECOM NETWORKS PROFESSIONAL MANUFACTURING POWER & UTILITIES DIGITAL BROADCASING TIME & FREQUENCY TIME
More informationPDH Switches. Switching Technology S PDH switches
PDH Switches Switching Technology S38.165 http://www.netlab.hut.fi/opetus/s38165 8-1 PDH switches General structure of telecom exchange Timing and synchronization Dimensioning example 8-2 1 PDH exchange
More informationBROADBAND AND HIGH SPEED NETWORKS
BROADBAND AND HIGH SPEED NETWORKS INTRODUCTION ATM stands for Asynchronous Transfer Mode ATM is a flexible high bandwidth, low delay network technology that is: Capable of handling voice, video and data
More informationWhite paper Application note
Applications of the Stand-Alone Synchronization Equipment in optical networks and the Synchronous Digital Hierarchy (SDH) White paper Application note Number 07 TELECOM NETWORKS PROFESSIONAL MANUFACTURING
More informationModule 10 Frame Relay and ATM
Module 10 Frame Relay and ATM Lesson 34 ATM: Concepts And Header 10.2.1 INTRODUCTION IP has a varying packet size which causes no problem while multiplexing but makes switching difficult. ATM uses a fixed
More informationSDH Principle. Copyright 2012 Huawei Technologies Co., Ltd. All rights reserved.
SDH Principle www.huawei.com Objectives Upon completion of this course, you will be able to: Understand the basic of SDH multiplexing standard Know the features, applications and advantages of SDH based
More informationIntroduction. TDM Techniques. Agenda. Point-To-Point Channels
atenkommunikation 384081 - SS 2007 atenkommunikation 384081 - SS 2007 Introduction TM Techniques Time ivision Multiplexing (synchronous, statistical) igital Voice Transmission, PH, SH line protocol techniques
More informationUNIT-II OVERVIEW OF PHYSICAL LAYER SWITCHING & MULTIPLEXING
1 UNIT-II OVERVIEW OF PHYSICAL LAYER SWITCHING & MULTIPLEXING Syllabus: Physical layer and overview of PL Switching: Multiplexing: frequency division multiplexing, wave length division multiplexing, synchronous
More informationChapter - 7. Multiplexing and circuit switches
Chapter - 7 Multiplexing and circuit switches Multiplexing Multiplexing is used to combine multiple communication links into a single stream. The aim is to share an expensive resource. For example several
More informationTable of Contents 1 E-CPOS Interface Configuration 1-1
Table of Contents 1 E-CPOS Interface Configuration 1-1 Overview 1-1 SONET 1-1 SDH 1-1 E-CPOS 1-5 Configuring an E-CPOS Interface 1-6 Configuring an E-CPOS Interface 1-6 Configuring the Operating Mode of
More informationATM Logical Connections: VCC. ATM Logical Connections: VPC
ATM Logical Connections: VCC Logical Connections in ATM are referred to as virtual channel connections (VCCs). Virtual channel (VC) is a generic term used to describe unidirectional transport of ATM cells
More informationCPOS Interface. Synchronous digital hierarchy (SDH), defined by CCITT (today s ITU-T), uses a SONET rate subset.
SONET/SDH Synchronous Optical Network (SONET), a synchronous transmission system defined by ANSI, is an international standard transmission protocol. It adopts optical transmission where transmission rates
More informationModems, DSL, and Multiplexing. CS158a Chris Pollett Feb 19, 2007.
Modems, DSL, and Multiplexing CS158a Chris Pollett Feb 19, 2007. Outline Finish up Modems DSL Multiplexing The fastest modems Last day, we say the combinations and phases used to code symbols on a 2400
More informationAsynchronous Transfer Mode (ATM) ATM concepts
Asynchronous Transfer Mode (ATM) Asynchronous Transfer Mode (ATM) is a switching technique for telecommunication networks. It uses asynchronous time-division multiplexing,[1][2] and it encodes data into
More informationLecture 15: Multiplexing (2)
Lecture 15: Multiplexing (2) Last Lecture Multiplexing (1) Source: chapter 8 This Lecture Multiplexing (2) Source: chapter8 Next Lecture Circuit switching (1) Source: chapter9 Digital Carrier Systems Hierarchy
More informationATM. Asynchronous Transfer Mode. these slides are based on USP ATM slides from Tereza Carvalho. ATM Networks Outline
ATM Asynchronous Transfer Mode these slides are based on USP ATM slides from Tereza Carvalho 1 ATM Networks Outline ATM technology designed as a support for ISDN Definitions: STM and ATM Standardization
More informationNTNU The. rt Networks. 1.1: Explain. Norwegian
NTNU The Norwegian Universityy of Science and Technology Department of Telematics TTM 4105 - Access and Transpor rt Networks Exercise 2 Multiplexi ing - solution n. Task 1: Fundamental variants of multiplexing
More informationSONET/SDH. By Iqtidar Ali
SONET/SDH By Iqtidar Ali SONET/SDH SONET/SDH means Synchronous Optical Network (SONET) was developed by ANSI. Synchronous Digital Hierarchy (SDH) was developed by ITU-T. The high bandwidth of fiber optic
More informationDigiPoints Volume 1. Leader Guide. Module 12 Asynchronous Transfer Mode. Summary. Outcomes. Objectives. Prerequisites
Asynchronous Transfer Mode Page 12.i DigiPoints Volume 1 Module 12 Asynchronous Transfer Mode Summary This last module of, covers ATM, and provides an end-to-end data communications model that draws on
More informationOptical networking: is the Internet of the future already here?
Optical networking: is the Internet of the future already here? Emilie CAMISARD Renater Optical technologies engineer - Advanced IP Services e-mail: camisard@renater.fr 23/11/04 ATHENS - Optical networking
More informationTelephone network. T Jouni Karvo, Raimo Kantola, Timo Kiravuo
Telephone network T-110.300 Jouni Karvo, Raimo Kantola, Timo Kiravuo Telephone network Background Topology Reference connection End systems Access network Transmission Switching & Signaling Layers User-Network
More informationTelephone network. Telephone network. Background. T Jouni Karvo, Raimo Kantola, Timo Kiravuo
Telephone network T-110.300 Jouni Karvo, Raimo Kantola, Timo Kiravuo Telephone network Background Topology Reference connection End systems Access network Transmission Switching & Signaling Layers User-Network
More informationAsynchronous Transfer Mode
ATM Asynchronous Transfer Mode CS420/520 Axel Krings Page 1 Protocol Architecture (diag) CS420/520 Axel Krings Page 2 1 Reference Model Planes User plane Provides for user information transfer Control
More informationChapter 10. Circuits Switching and Packet Switching 10-1
Chapter 10 Circuits Switching and Packet Switching 10-1 Content Switched communication networks Circuit switching networks Circuit-switching concepts Packet-switching principles X.25 (mentioned but not
More informationBandwidth-on-Demand up to very high speeds. Variety of physical layers using optical fibre, copper, wireless. 3BA33 D.Lewis
Broadband ISDN 3BA33 David Lewis 3BA33 D.Lewis 2007 1 B-ISDN Model has 3 planes User Control Management 3BA33 D.Lewis 2007 3 Broadband ISDN Was Expected to be the Universal Network of the future Takes
More information1/29/2008. From Signals to Packets. Lecture 6 Datalink Framing, Switching. Datalink Functions. Datalink Lectures. Character and Bit Stuffing.
/9/008 From Signals to Packets Lecture Datalink Framing, Switching Peter Steenkiste Departments of Computer Science and Electrical and Computer Engineering Carnegie Mellon University Analog Signal Digital
More informationFinal draft ETSI EN V1.2.1 ( )
Final draft EN 300 462-2-1 V1.2.1 (2002-01) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Generic requirements for synchronization networks; Part 2-1: Synchronization
More informationWireless Networks. Communication Networks
Wireless Networks Communication Networks Types of Communication Networks Traditional Traditional local area network (LAN) Traditional wide area network (WAN) Higher-speed High-speed local area network
More informationSynchronization of the Circuit switched network
Synchronization of the Circuit switched network ITU-T Recommendations G.810, G.811, G.812, G.823 Rka/ML -k2002 Telecommunication Switching Technology 5a - 1 Summary of course scope H.323 or SIP IP SIP
More informationSynchronisation in Telecom Networks
Synchronisation in Telecom Networks ITSF / Jean-Loup Ferrant / November 6, 006 Network synchronisation history () Page -PSTN and PDH -Switches needed synchronisation in order to comply with slip generation
More informationSubject Data Communication. Subject Code 15CS46. Module 2 (Part 2) Multiplexing and Switching
1. What is multiplexing? What are types of multiplexing? (Dec 2012) Multiplexing is the set of techniques that allows the simultaneous transmission of multiple signals across a single data link. If the
More informationCSIS Frequency Division Multiplexing. Basic Types of Multiplexing. Frequency Division Multiplexing. Frequency Division Multiplexing.
Multiplexing: combining information streams from multiple sources for transmission over a shared medium Demultiplexing: separating a combination back into individual information streams CSIS 4222 Ch 11:
More informationReal Time Implementation of Data Communication using Ipv4Telecom Network through Sdhstm-4 Digital Transmission Wan
RESEARCH ARTICLE Real Time Implementation of Data Communication using Ipv4Telecom Network through Sdhstm-4 Digital Transmission Wan SharadaOhatkar*, Sanjay Thakare**, RachnaChavan*, Mugdha Kulkarni *,
More informationModule 3. Wide Area Networking (WAN)
Module 3 Wide Area Networking (WAN) When many nodes or LAN s are connected together in a large scale, we have a WAN. This may be world wide. Because of the separation of the nodes, the Public Data Network
More informationCOPYRIGHTED MATERIAL INTRODUCTION TO OPTICAL TRANSPORT CHAPTER 1
CHAPTER 1 INTRODUCTION TO OPTICAL TRANSPORT This chapter covers the history of the development of SDH, SONET, and OTN. For consistency in the terminology used in this book I have included a list of conventions.
More informationCPEG 514. Lecture 11 Asynchronous Transfer Mode (ATM) CPEG 514
Lecture 11 Asynchronous Transfer Mode () Outline Introduction Virtual Circuit Setup PVC vs. SVC Quality of Service and Congestion Control IP over and Frame Relay interworking Network (integrated voice,
More informationReference Access and Interconnection Offer
1. Commercial Proposal for Reference Access and Interconnection Offer Sub Annex E Technical Specification Table of Contents 1 General... 3 2 Physical and Electrical Interface... 4 3 Transmission... 7 4
More informationIP over. Mario Baldi. Politecnico di Torino. (Technical University of Turin) IPinterconnection - 1 Copyright: si veda nota a pag.
IP over ATM SDH DWDM Mario Baldi Politecnico di Torino (Technical University of Turin) www.baldi.info IPinterconnection - 1 Copyright: si veda nota a pag. 2 Nota di Copyright This set of transparencies,
More informationElectromagnetic Spectrum
Electromagnetic Spectrum PCS FMRadi o/ TV Short wave Radi o AM Broadcast Ul trasoni c Soni c Vi si ble Li ght Infrared Li ght Ul travi ol et X- Rays Frequency 1 khz 1 M Hz 1 G Hz 1 THz 1 Y Hz 1 ZHz Wavelength
More informationDirect Link Networks. Framing. Lecture - Encoding & Framing 1. Problems. Areas for Discussion
Areas for Discussion Direct Link s Joseph Spring School of Computer Science 3COM0271 Computer Protocols & Architecture s Based on Chapter 2, Peterson & Davie, Computer s: A Systems Approach, 4 th Ed Problems
More informationName of Course : E1-E2 CFA. Chapter 15. Topic : DWDM
Name of Course : E1-E2 CFA Chapter 15 Topic : DWDM Date of Creation : 28.03.2011 DWDM 1.0 Introduction The emergence of DWDM is one of the most recent and important phenomena in the development of fiber
More informationInternet Architecture and Protocol
Internet Architecture and Protocol Set# 04 Wide Area Networks Delivered By: Engr Tahir Niazi Wide Area Network Basics Cover large geographical area Network of Networks WANs used to be characterized with
More informationUnderstanding the Variable Bit Rate Real Time (VBR rt) Service Category for ATM VCs
Understanding the Variable Bit Rate Real Time (VBR rt) Service Category for ATM VCs Document ID: 10414 Contents Introduction Prerequisites Requirements Components Used Conventions What is Variable Bit
More informationNETWORK PARADIGMS. Bandwidth (Mbps) ATM LANS Gigabit Ethernet ATM. Voice, Image, Video, Data. Fast Ethernet FDDI SMDS (DQDB)
1. INTRODUCTION NETWORK PARADIGMS Bandwidth (Mbps) 1000 ATM LANS Gigabit Ethernet ATM 100 10 Fast Ethernet FDDI SMDS (DQDB) Voice, Image, Video, Data 1 Ethernet/ Token Ring/ Token Bus Frame Relay X.25
More informationITU-T G.832. Transport of SDH elements on PDH networks Frame and multiplexing structures
INTERNATIONAL TELECOMMUNICATION UNION ITU-T G.832 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (10/98) SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS Digital transmission systems
More informationTELECOMMUNICATION SYSTEMS
TELECOMMUNICATION SYSTEMS By Syed Bakhtawar Shah Abid Lecturer in Computer Science 1 Public Switched Telephone Network Structure The Local Loop Trunks and Multiplexing Switching 2 Network Structure Minimize
More informationLecture 6 Datalink Framing, Switching. From Signals to Packets
Lecture 6 Datalink Framing, Switching David Andersen Department of Computer Science Carnegie Mellon University 15-441 Networking, Spring 2005 http://www.cs.cmu.edu/~srini/15-441/s05/ 1 From Signals to
More informationModule 1. Introduction. Version 2, CSE IIT, Kharagpur
Module 1 Introduction Version 2, CSE IIT, Kharagpur Introduction In this module we shall highlight some of the basic aspects of computer networks in two lessons. In lesson 1.1 we shall start with the historical
More informationIntroduction to Optical Networks
Introduction to Optical Networks P. Michael Henderson mike@michael-henderson.us 1 Agenda The physics of light Laser and photodetector operation Characteristics of optical fiber Optical amplifiers SONET
More informationOptical Communications and Networking 朱祖勍. Nov. 27, 2017
Optical Communications and Networking Nov. 27, 2017 1 What is a Core Network? A core network is the central part of a telecommunication network that provides services to customers who are connected by
More informationUNIT- 2 Physical Layer and Overview of PL Switching
UNIT- 2 Physical Layer and Overview of PL Switching 2.1 MULTIPLEXING Multiplexing is the set of techniques that allows the simultaneous transmission of multiple signals across a single data link. Figure
More informationIntegrating Euro-ISDN with ATM Technology : Interworking Mechanisms and Services Support
Integrating Euro-ISDN with ATM Technology : Interworking Mechanisms and Services Support L. Mandalos [1], K. Leonidou [2], C. Andreopoulos [3], J. Drakos [4], S. Koubias [5], G. Papadopoulos [6] [1] Research
More informationWECC Guideline Digital Circuits Synchronization
WECC Guideline Digital Circuits Synchronization March 8, 2018 155 North 400 West, Suite 200 Salt Lake City, Utah 84103-1114 WECC Guideline: Digital Circuits Synchronization 2 Table of Contents I. Introduction...
More informationBROADBAND AND HIGH SPEED NETWORKS
BROADBAND AND HIGH SEED NETWORKS LAYERS The function and associated information of the planes is as follows: The reference model is composed of the following planes: Control lane manages the call and connection.
More informationNGN - SYNCHRONOUS DIGITAL HIERARCHY
NGN - SYNCHRONOUS DIGITAL HIERARCHY http://www.tutorialspoint.com/ngn/ngn_synchronous_digital_hierarchy.htm Copyright tutorialspoint.com SDH Networks replaced PDH and had several key advantages. G.707,
More informationFPGA BASED IMPLEMENTATION OF STM-16 FRAMER IP CORE
FPGA BASED IMPLEMENTATION OF STM-16 FRAMER IP CORE 1 T.SHIVARAJA, 2 RASHMI PRIYADARSHINI, 3 RAJA JITENDRA NAYAKA 1 Mtech-4th Sem,ECE department, RITM Yelahanka Bangalore, Karnataka, India 2 Asst. Professor,
More informationUnderstanding TeleCom Networks Today II The World of Data
Understanding The World of Data Course Description Explore the world of data 2.5/3G, Optical, Frame Relay, ATM Networks, Wireless and more... Networks are converging. No more discrete data and voice networks
More informationTelco Scalable Backbones PDH, SONET/SDH
Telco Scalable Backbones PDH, SONET/SDH (C) Herbert Haas 2005/03/11 1 Everything that can be invented has been invented Charles H. Duell, commissioner of the US Office of Patents 1899 2 Agenda Basics Shannon
More informationPDH Switches. Switching Technology S P. Raatikainen Switching Technology / 2004.
PDH Switches Switching Technology S38.165 http://www.netlab.hut.fi/opetus/s38165 L8-1 PDH switches General structure of a telecom exchange Timing and synchronization Dimensioning example L8-2 PDH exchange
More informationSS#7. T Jouni Karvo, Timo Kiravuo
SS#7 T-110.300 Jouni Karvo, Timo Kiravuo Telephone exchanges Subscriber lines are connected to the telephone exchanges Originally each customer had a direct connection (electrical pair) to the exchange
More informationWAN Technologies (to interconnect IP routers) Mario Baldi
WAN Technologies (to interconnect IP routers) Mario Baldi www.baldi.info WAN_Technologies - 1 Copyright: see page 2 Copyright Notice This set of transparencies, hereinafter referred to as slides, is protected
More informationIntroduction to Networks
Introduction to Networks Network Topology How we interconnect network users Network Hierarchy The connection between network topology and geographical size Telecommunication (Phone Networks) Circuit Switching
More informationCore Network. Core Network Technologies. S Verkkopalvelujen tuotanto S Network Service Provisioning Lecture 2: Core Network Technologies
Lic.(Tech.) Marko Luoma (1/37) Lic.(Tech.) Marko Luoma (2/37) S-38.192 Verkkopalvelujen tuotanto S-38.192 Network Service Provisioning Lecture 2: Core Network Technologies Connects MAN networks together
More informationIntroduction To Optical Networks Optical Networks: A Practical Perspective
Introduction To Optical Networks Optical Networks: A Practical Perspective Galen Sasaki Galen Sasaki University of Hawaii 1 Galen Sasaki University of Hawaii 2 Galen Sasaki University of Hawaii 3 Telecommunications
More informationOptical networking technology
1 Optical networking technology Technological advances in semiconductor products have essentially been the primary driver for the growth of networking that led to improvements and simplification in the
More informationDirect Link Networks. Lecture - Encoding & Framing 1. Areas for Discussion. Problems
Areas for Discussion Direct Link s Joseph Spring School of Computer Science 3COM0088 Computer Protocols & Architecture s Based on Chapter 2, Peterson & Davie, Computer s: A Systems Approach, 3 rd Ed Problems
More informationTRANSPORT OF SDH ELEMENTS ON PDH NETWORKS: FRAME AND MULTIPLEXING STRUCTURES ITU-T
INTERNATIONAL TELECOMMUNICATION UNION ITU-T G.832 TELECOMMUNICATION (11/93) STANDARDIZATION SECTOR OF ITU DIGITAL NETWORKS TRANSPORT OF SDH ELEMENTS ON PDH NETWORKS: FRAME AND MULTIPLEXING STRUCTURES ITU-T
More informationMetropolitan Area Networks
Metropolitan Area Networks Bridge larger distances than a LAN, usage e.g. within the city range or on a campus Only one or two cables, no switching elements. Thus a simple network design is achieved All
More informationPublic Switched Telephone Network (PSTN II/II)
Public Switched Telephone Network (PSTN II/II) Topics today in PSTN Trunk Network Node 1 Node 2 Access Access! A: Switching types! Connectionless/ connection oriented! Packet/circuit! B: PSNT exchanges
More information2. The initialization vector (IV) is used in the framework of
Advanced Network Protocols Prof. E. Damiani The exam is composed of three sections: a multiple choice and two open question ones. Please do NOT write your answers on the exam text. Rather, hand them in
More informationINTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU G.823 (03/2000) SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS Digital networks Quality and
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 ECI TELECOM S LQLAB 30 Hasivim Street Petah-Tikva 4959338, ISRAEL Moshe Perel Phone: 972 52-4008642 Email: Moshe.Perel@ecitele.com ELECTRICAL Valid to: June
More informationMA Yan, BUPTCC, ~16 BUPT Information Network Center LAN LAN. Transmission system
LAN LAN Transmission system 1 Campus 1 2 Office 3 Office 2 Office 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 ... 4 Local Loop End Office Trunks End Office End Office End Office Tandem Office LD
More informationINTERNATIONAL TELECOMMUNICATION UNION INTEGRATED SERVICES DIGITAL NETWORK (ISDN) OVERALL NETWORK ASPECTS AND FUNCTIONS
INTERNATIONAL TELECOMMUNICATION UNION ITU-T I.363 TELECOMMUNICATION (03/93) STANDARDIZATION SECTOR OF ITU INTEGRATED SERVICES DIGITAL NETWORK (ISDN) OVERALL NETWORK ASPECTS AND FUNCTIONS B-ISDN ATM ADAPTATION
More informationOverview of High Speed Network Technologies
Overview of High Speed Network Technologies PASI (Pan-American Advanced Studies Institute) Grid Computing and Advanced Networking Technologies for e-science Tereza Cristina M. B. Carvalho ANSP/LARC/PCS/EPUSP
More informationA T M. Cell Switched Technology. not SMDS. Defacto Standard Multimedia capable Use with SONET or SDH. Fixed Length - 53 bytes. DigiPoints Volume 1
A T M Cell Switched Technology Fixed Length - 53 bytes not SMDS Defacto Standard Multimedia capable Use with SONET or SDH SCTE VA 12.1 SONET Optical Carrier (OC) Rates and SDH Synchronous Transport Module
More informationBROADBAND AND HIGH SPEED NETWORKS
BROADBAND AND HIGH SPEED NETWORKS SWITCHING A switch is a mechanism that allows us to interconnect links to form a larger network. A switch is a multi-input, multi-output device, which transfers packets
More informationNetworks 15.2 Multiplexing Technologies Access Networks 15.5 Common Peripheral Interfaces
Chapter 15 Computer and Multimedia Networks 15.11 Basics of Computer and Multimedia Networks 15.2 Multiplexing Technologies 15.3 LAN and WAN 15.4 Access Networks 15.5 Common Peripheral Interfaces 15.6
More information