User guide for TRANZEO-Series 6000

Transcription

1 User guide for TRANZEO-Series Connecting hardware. Polarity Determine if the antenna s polarization will be horizontal or vertical before installation. The TR-6000 radios can be used in either polarity. Site Selection: Before installation, determine the Access Point location. Proper placement of the Access Point is critical to ensure optimum radio range and performance. Typically, the best location to place your Access Point at your site is the center of your wireless coverage area. Try to place your mobile stations within the line of sight. Obstructions may impede performance of the Access Point. Access Point Placement You can place the Access Point on a flat surface such as a table or cabinet, or mount the unit on a vertical surface like a wall. The integrated antenna of your Access Point performs best in an open environment with as few obstructions as possible Pierre Houssin sales and tech assistance Page 1

2 Connecting your Tranzeo to your network is very easy, as it s using the POE (Power Over Ethernet) technology. For this you will need two direct Ethernet cable (RJ45) and the power adaptator provided. STEP 12: Connect the Cat 5 cable from the radio into the RJ-45 jack marked CPE on the POE adapter. The POE adapter is not weatherproof and should be installed indoors. STEP 13: Connect the power adapter to the POE adapter and plug the other end to an outlet.the POE adapter will be powered on and the power indicator on the top panel will turn on. We recommend connecting the power adapter to an outlet with surge suppression capability with an uninterrupted power supply (UPS) for reduced outages. NOTE: ONLY use the power adapter supplied with the Access Point. Otherwise, the product may be damaged. STEP 14: To configure the TR-6000 Series radio, connect the Ethernet cable to the POE adapter and to a computer. Ensure that the distance between the computer and the radio does not exceed 300 ft (90 m). NOTE: If connecting to a hub or switch, a crossover cable may be required. Pierre Houssin sales and tech assistance Page 2

3 2. Connecting to the radio. We are Wholesaler in Before accessing the configuration interface, you have to change the network connection settings in your computer to be on the same subnet as the radio. Changing the IP Address - Windows XP In your computer, open Control Panel > Network Connections > Local Area Connection. In Local Area Connection Status > General, click Properties. In Local Area Connection Properties > General, select Protocol (TCP/IP) and click Properties. In Protocol (TCP/IP) Properties > General, select Use the following IP address. Enter your IP address and Subnet Mask. The default IP address of the radio is , which cannot be used here. So type IP address and gateway Click OK and Close. Pierre Houssin sales and tech assistance Page 3

4 Login into the Configuration Interface After defining the network settings, follow these steps to login into the Tranzeo Configuration Interface. 1. Open your browser ( Explorer, Netscape, or Firefox). 2. In the address bar, type your IP address (default IP: 3. In the login dialog, enter your Username and Password (if you re a firsttime user, follow the instructions below). 4. Click OK. You will then access the configuration interface. If you re a first-time user: 1. Enter the default username admin and the default password default. 2. In the Password Set/Reset window, change the Administration and Recovery* passwords. They cannot be left as default and must be different from each other. You can change the usernames too. 3. Click Apply to save the changes. 4. You will be prompted to enter your new username and password in the login dialog. You will then access the configuration interface. *The recovery username and password are used to access the Password Set/Reset window if the administration password is lost. Pierre Houssin sales and tech assistance Page 4

5 3. Setup menu In this section you would be able to configure wireless and administrative settings for the TR-6000 Series radio. Wireless Settings This window displays the wireless configuration of the device. The contents are slightly different for access point and CPE. To operate the radio in PxP mode: 1. Set one radio to Access Point and the other to Infrastructure Station. 2. Enter the same SSID on both radios. 3. Set the Channel on the access point. 4. On both radios, enter the Mac address of the opposite radio in the PxP Mac Address field (no colons). 5. Check off PxP Mode Enabled. Note: In PxP mode, the LEDs on the radios will operate the same as in Infrastructure Station mode, with LEDs proportional to signal strength. Pierre Houssin sales and tech assistance Page 5

6 To operate the radio in PxP mode: 1. Set one radio to Access Point and the other to Infrastructure Station. 2. Enter the same SSID on both radios. 4. Set the Channel on the access point. 3. On both radios, enter the Mac address of the opposite radio in the PxP Mac Address field (no colons). 4. Check off PxP Mode Enabled. Note: In PxP mode, the LEDs on the radios will operate the same as in Infrastructure Station mode, with LEDs proportional to signal strength. Pierre Houssin sales and tech assistance Page 6

7 Network Configuration We are Wholesaler in In this window you can control the network configuration of the device. First, you must define if your radio will operate as a bridge or router. The content of the window varies depending on your selection. When changing modes, the radio may need to reboot before certain features become available. Bridge Mode or Router mode From this window you can access specific windows to configure the DHCP Server, QoS, Static Routes, Port Filtering, and Port Forwarding. If the feature is available, it will appear like a link. Pierre Houssin sales and tech assistance Page 7

8 5. Trouble-shooting You may lose information about username and password in this case you need to call Afrikanet and we will open a trouble-ticket in order to reset to default factory the devise. In order to do this you need to get the information below : Model Number: * Serial Number: * Invoice number: * Date of Purchase: * Firmware Version: * Contact Telephone Number: * Radio Mode of operation: Access point Mode Authentication (MAC auth / Radius): Security (WEP / WPA): After we will give you the procedure to reset to default factory your computer. For all other problems, please contact Afrikanet or go on our website : Afrikanet Oxford Consultech NST & T Universal Phones UK Ltd Oxford Culham Innovations Center Building D5 Science Park Abingdon OX143DB Oxfordshire United Kingdom TEL FAX Pierre Houssin sales and tech assistance Page 8

9 6. Specifications Pierre Houssin sales and tech assistance Page 9