AN A. GPON Optical Network Terminal. Product Manual. Version: A/1. FiberHome Telecommunication Technologies Co., Ltd.

Transcription

1 AN A GPON Optical Network Terminal Prodct Manal Version: A/1 FiberHome Telecommnication Technologies Co., Ltd. April 2017

2 Thank yo for choosing or prodcts. We appreciate yor bsiness. Yor satisfaction is or goal. We will provide yo with comprehensive technical spport and after-sales service. Please contact yor local sales representative, service representative or distribtor for any help needed at the contact information shown below. Fiberhome Telecommnication Technologies Co., Ltd. Address: No. 67, Gangg Changye Jie, Whan, Hbei, China Zip code: Tel: /0884 (for Malaysia) (for Soth Asia) (for Soth America) Fax: Website:

3 Legal Notice are trademarks of FiberHome Telecommnication Technologies Co., Ltd. (Hereinafter referred to as FiberHome) All brand names and prodct names sed in this docment are sed for identification prposes only and are trademarks or registered trademarks of their respective holders. All rights reserved No part of this docment (inclding the electronic version) may be reprodced or transmitted in any form or by any means withot prior written permission from FiberHome. Information in this docment is sbject to change withot notice.

4 Safety Precations For yor correct and safe operations on the eqipment, please careflly read and strictly observe the following safety instrctions: High optical power can case bodily harm, especially to eyes. Never look directly into the end of the optical transmitter fiber jmper or the end of its active connector. Exercise care if yo mst bend fibers. If bends are necessary, the fiber bending radis shold never be less than 38mm. Overloaded power sockets or damaged cables and connectors may case electric shock or fire. Reglarly check related electric cables. If any of them is damaged, replace it immediately. Use the power spply adapter provided in the package only. Using other adapters may case eqipment damage or operation failres. Install the eqipment in a well ventilated environment withot high temperatre or direct snlight to protect the eqipment and its components from overheating, which can reslt in damage. Disconnect the power in lightning weather and disconnect all the wires and cables on the device (sch as the power cable, network cable and phone cable), so as to prevent device from being damaged by lightning. Do not place this eqipment in damp or near moistre environment. Water will lead to abnormal operation of device and even the danger cased by short circit. Do not lay this eqipment on an nsteady base. I

5 Contents Safety Precations...I 1 Docmentation Gide Prodct Introdction Prodct Positioning Prodct Specifications Interface Specifications GPON Interface LAN Interface Introdction to the AN A Appearance Prodct Characteristics Fnctions and Featres Technical Specifications Web Configration Gide Logging into Web Configration GUI Locally Stats Device Information WAN Side Stats LAN Side Stats Optical Power Stats Network LAN Settings Broadband Settings DHCP Server Athentication Setting Secrity Firewall Remote Control Dynamic DoS...42

6 3.4.4 HTTPS Application DDNS Port Forwarding NAT UPnP DMZ Network Diagnosis Management Accont Management Device Management Log Management Handling Common Problems Power Stats Indicator LED Extingished Register Stats Indicator LED Extingished Optical Signal Stats Indicator LED Blinking Ethernet Interface Stats Indicator LED Extingished Failing to Access Local Web Login GUI and Failing to Ping Failing to Access Internet Using the LAN Port Measred Internet Access Rate Lower or Higher Than The Standard Vale Standards and Protocols...60 Appendix A Abbreviations...62

7 1 Docmentation Gide Docment Orientation AN A Prodct Manal introdces the positioning, featres, fnctions, technical specifications of the ONT (Optical Network Terminal) prodct AN A as well as Web configrations and handling of common problems, so that readers can have an overall knowledge abot the AN A. Intended Readers Marketing personnel Commissioning engineers Operation and maintenance engineers Version Information Version A Version Information Initial version Content Chapter Content Prodct Introdction Web Configration Gide Prodct positioning Prodct specifications Interface specifications Introdction to the AN A Logging into Web configration GUI locally Stats Network Secrity Application Management Handling Common Problems Standards and Protocols Introdces how to handle common problems encontered dring prodct operation and service test, inclding abnormal stats of indicator LEDs, failing to access the Internet, failre of voice service test, etc. International standards and commnications protocols Version: A/1 1

8 2 Prodct Introdction Prodct Positioning Prodct Specifications Interface Specifications Introdction to the AN A 2 Version: A/1

9 2 Prodct Introdction 2.1 Prodct Positioning The AN A is an FTTH-type GPON ONT. It provides sers with commnication and entertainment services in the form of data, voice, video, and so on, to meet the integrated access demand of families and small-scaled enterprises. See Figre 2-1 for the network positioning of the AN A. Figre 2-1 Network Application of the AN A 2.2 Prodct Specifications The tables below list the interfaces on the AN A and the services spported by the ONT for sers' reference on ONT configration. Table 2-1 lists the interfaces spported by the AN A. Table 2-1 Interfaces Spported by the AN A ONT Type Ethernet Interface Qantity POTS Interface Qantity Wi-Fi Interface USB Interface Qantity CATV Interface Qantity AN A 1 (GE) Version: A/1 3

10 AN A GPON Optical Network Terminal Prodct Manal Table 2-2 lists the service types spported by the AN A. Table 2-2 Service Types Spported by the AN A ONT Type Internet Service Mlticast Service Voice Service Wi-Fi Service AN A Note: indicates spported ; indicates not spported. Service Reliability The AN A spports MTBF p to hors. 2.3 Interface Specifications GPON Interface See Table 2-3 for the specifications of the GPON interface. Table 2-3 GPON Interface Specifications Parameter Specification Standard compliance ITU-T G.984, Class B+ Transmission rate Interface mode Interface type Maximm transmission distance Central wavelength Optical power Extinction ratio Receiving sensitivity Maximm overload optical power Rx: 2.5 Gbit/s; Tx: 1.25 Gbit/s Single-mode SC/UPC or SC/APC 20 km Tx: 1310 nm; Rx: 1490 nm Tx optical power: 0.5 dbm to 5.0 dbm Rx optical power: -8 dbm to -29 dbm More than 10 db -27 dbm to -29 dbm -8 dbm LAN Interface Table 2-4 shows the specifications of the LAN interface. 4 Version: A/1

11 2 Prodct Introdction Table 2-4 Parameter LAN Interface Specifications Specification Standard compliance Interface type Interface rate Maximm transmission distance Working mode Specifications of the cable sed IEEE 802.3ab RJ Mbit/s, 100 Mbit/s or 1000 Mbit/s 100m Spports fll-dplex or half-dplex and 10/100/1000 M ato negotiation. CAT-5 nshielded twisted pair 2.4 Introdction to the AN A Appearance The following describes the appearance of the AN A, inclding the overall look, interfaces, bttons, and indicator LEDs. Note: The pictres here are only for reference. Appearance The overall look of the AN A is shown in Figre 2-2. Version: A/1 5

12 AN A GPON Optical Network Terminal Prodct Manal Figre 2-2 Overall Look of the AN A Interface and Btton Interfaces and bttons of the AN A are located on the rear and side panels of the eqipment. Figre 2-3 shows the rear panel and Figre 2-4 shows the side panel. Figre 2-3 Rear Panel of the AN A Figre 2-4 Side Panel of the AN A Table 2-5 describes the interfaces and bttons of the AN A. 6 Version: A/1

13 2 Prodct Introdction Table 2-5 Interfaces and Bttons of the AN A Interface and Btton Description Fnction On/Off Power switch Trns on or off the power for the eqipment. Power Power interface Connects with the power adapter. LAN Ethernet interface Connects with the compter, IP roter or IP set top box. PON Fiber interface Connects with optical fiber for plink access. Light Indicator LED switch Trns on or off the indicator LEDs. Reset Reboot btton Pressing down the btton for no more than 5 seconds to reboot the eqipment; pressing down the btton for more than 5 seconds to restore the factory settings and reboot the eqipment. Indicator LED Description Indicator LEDs of the AN A are located on the front panel of the eqipment. Table 2-6 describes the indicator LEDs. Table 2-6 Indicator LEDs on the AN A Indicator LEDs Meaning Color Stats Stats Description Power Power stats indicator LED Green ON OFF The eqipment is powered on. The eqipment is not powered on. LAN Ethernet interface stats Green ON Blinking The interface is connected to the ser terminal and no data is transmitted. The interface is transmitting / receiving data. indicator LED OFF The interface is not connected to the ser terminal. LOS Optical signal stats indicator Red Blinking The eqipment has not received the optical signal. LED OFF The eqipment has received the optical signal. PON Register stats indicator LED Green ON Blinking OFF The ONT is activated. The ONT is being activated. Activation of the ONT is not yet started. Version: A/1 7

14 AN A GPON Optical Network Terminal Prodct Manal Prodct Characteristics The AN A can be sed together with the OLT eqipment to make p a GPON system and access mltiple services for sers. The AN A has the following characteristics: 1. GPON access capability Conforms to ITU-T G.984 series of standards, with good interoperability. Provides large-capacity GPON transmission bandwidth: spports 2.5 Gbit/s for the downlink rate and 1.25 Gbit/s for the plink rate. Spports the DBA (Dynamic Bandwidth Allocation) algorithm. Spports long-hal transmission. The maximm transmission distance can reach 20 km. 2. Abndant service types 3. Gateway fnctions The eqipment provides abndant physical interfaces on the sbscriber side to access mltiple services sch as Internet access and video services. Serves as home gateway and provides abndant and reliable gateway fnctions. Fnctions as the DHCP Server to cater for application demands in different scenarios. Spports configring protection against DoS attack, filtering of MAC addresses, IP addresses and URL addresses, firewall and ACL rles to garantee safe operation of the eqipment. 4. Remote atomatic provisioning of services, maintenance and management The eqipment adopts the management based on TR-069 and OMCI, and spports TR-069 over OMCI. It can manage terminal services withot IP network, which facilitates atomatic provisioning, maintenance and management of services remotely. 8 Version: A/1

15 2 Prodct Introdction Spports configring the global profile and delivering the XML configration file on the network management system. Only a few changes are reqired to deliver the ONT services in a batch manner and make network adjstment. Spports configring the ser-defined pgrade policies on the network management system so that the eqipment can be pgraded atomatically after being powered on. Spports collecting performance data of the ONT remotely via the network management system to enable real-time monitoring of the network performance. Spports remote falt isolation for the ONT via the network management system. Falts can be isolated remotely according to the alarms reported to redce the maintenance cost Fnctions and Featres Table 2-7 lists the fnctions and featres of the AN A Table 2-7 Fnctions and Featres of the AN A Item Description Compliant with standards ITU-T G.984.1, G.984.2, G and G Spports GEM encapslation (Ethernet over GEM is spported, bt ATM encapslation is not spported). GPON interface specifications The GPON system adopts the single-fiber bidirectional transmission mechanism, sing the TDMA mode with the wavelength 1310 nm in the plink direction, and the broadcast mode with the wavelength 1490 nm in the downlink direction. Spports the embedded OAM message, PLOAM message and OMCI message. GPON Spports the splicing of data packets and OMCI protocol packets in the plink direction. Splicing with adaptive message length and that with fixed length are spported. Spports bearing the downlink broadcast packets and nknown mlticast packets via the broadcast GEM port. GEM Port Spports mapping from GEM ports to T-CONTs. Spports mltiple flow mapping modes. Spports the GEM port loopback. T-CONT Spports T-CONTs of Type 1 to Type 5. A T-CONT spports no less than 64 GEM ports. Version: A/1 9

16 AN A GPON Optical Network Terminal Prodct Manal Table 2-7 Fnctions and Featres of the AN A (Contined) Item Description Spports eight T-CONTs. DBA FEC Spports DBA in the SR and NSR modes. Spports DBA Piggy-back DBR Mode 0. Spports bi-directional FEC: downlink FEC decoding and plink FEC encoding. Spports downlink FEC performance statistics. Spports encryption of downlink nicast data channel. Encryption Spports the AES-128 encryption algorithm. Spports generation of the key and response to the OLT's reqest for key. Spports OMCI channel encryption. Spports the ONT registration process as specified in ITU-T. G Registration athentication Spports for athentication modes: SN, Password, SN Password and LOID. Spports performance statistics for the Ethernet interface. Spports performance statistics for the GEM interface. Complies with the IEEE standard. Spports configring the Ethernet interface rate, working mode, and MDI/MDIX ato-negotiation mode. Spports manal configration to the rate 10/100/1000 Mbit/s. Spports manal configration of the half dplex or fll dplex mode. Ethernet Spports nlink / downlink rate control based on the Ethernet interface, with the control granlarity of 64 kbit/s. Spports the PAUSE flow control. Spports the loopback detection at the sbscriber side. Spports learning p to 1024 MAC addresses. Spports global configration of enabling / disabling the MAC address learning fnction. Spports remote configration of the MAC address aging time. The vale ranges between 0s and 300s. The defalt vale is 80s. Spports the IGMP Snooping protocol. Spports IGMP v1/v2/v3. Spports filtering and forwarding of mlticast MAC addresses. Mlticast Spports controllable mlticast and ncontrollable mlticast. Spports fast leave. Spports translation, transparent transmission and stripping of the mlticast VLAN tags. 10 Version: A/1

17 2 Prodct Introdction Table 2-7 Fnctions and Featres of the AN A (Contined) Item Description Spports VLAN translation for the plink mlticast protocol packets. Spports filtering the downlink mlticast packets. Spports bearing downlink mlticast service flow and IGMP signaling packets via different GEM ports. Spports configration of the mlticast GEM ports. Spports athentication of the GEM ports. Spports no less than 256 mlticast grops. Uses the IPoE/PPPoE mode for the mlticast services. Spports the IPv6 Snooping mlticast service, spports the MLDv1 information, MLDv2 qery information and MLDv2 report information. Spports the IEEE 802.1Q VLAN standard. VLAN Spports joining the 802.1Q VLAN in the tag / ntag mode. Spports p to 4095 VLANs. Wire-speed forwarding Spports Layer 2 / Layer 3 wire-speed forwarding. Spports the IPv4/v6 dal stack. Spports obtaining network parameters sch as the ser IP address, sbnet mask and DNS in the DHCP mode. Spports reporting the physical location of the Ethernet interface based on DHCP Option82. Layer 3 featres Spports obtaining ser IP addresses in the PPPoE mode, and spports the PPPoE+ fnction for precise identification of sers. Spports static roting and defalt roting. Spports DDNS, NAT, port forwarding and DMZ. Spports ARP, UPnP, ALG, Portal and QoS. Spports the firewall. Spports packet filtering. Spports filtering MAC addresses. Secrity Spports filtering URL addresses. Spports protection against illegal message (DoS, ARP) attacks; spports sppression of broadcast storms. Spports configring the HTTPS safe channel. Spports configring ACL rles for the ONT. Spports remote control. Management and maintenance Spports local service configration, qery and software pgrade based on the Web page. Spports management of the OMCI configration and qeries. Version: A/1 11

18 AN A GPON Optical Network Terminal Prodct Manal Table 2-7 Fnctions and Featres of the AN A (Contined) Item Description Spports delivering the XML configration file via the OMCI, alarm reporting, alarm synchronization and performance statistics. Spports atomatic provisioning of services, eqipment management and software pgrade remotely based on OMCI/TR-069. Spports qery of the ONT optical modle information. Spports TYPE B protection. Provides abndant QoS fnctions; spports global configration of qee priorities and flexible mapping of 802.1p vales in packets. QoS Spports the ACL fnction to match traffic based on the ACL rles. Spports three qee schedling modes (PQ, WRR and PQ+WRR); spports configring the weight of the qees nder schedling, so as to garantee the qality of high-qos services sch as voice and video in the mlti-service scenario Technical Specifications See Table 2-8 for the technical specifications of the AN A. Table 2-8 Technical Specifications of the AN A Classification Item Description Mechanical parameters Dimensions 25.5mm 112mm 112mm (H W D) Wall monting hole distance 75mm Weight Abot 120g Power spply parameter Power consmption parameters Environment parameters DC Static power consmption Maximm power consmption Operating temperatre Storage temperatre Environmental hmidity DC 12 V/0.5A 3W 4W -5 to to 70 10% to 90% (no condensation) 12 Version: A/1

19 3 Web Configration Gide The following introdces the Web GUIs for the administrator sers of the AN A, inclding the parameter meanings and operation methods. Note: Configre the ONT on the OLT sing the access network management system. Please refer to the relevant OLT configration gide. Logging into Web Configration GUI Locally Stats Network Secrity Application Management Version: A/1 13

20 AN A GPON Optical Network Terminal Prodct Manal 3.1 Logging into Web Configration GUI Locally Prereqisites The following discsses how to log into the ONT Web GUI locally and introdces the configration GUI layot. The ONT has been connected with the compter correctly. The ser compter is started normally. The ONT is started normally. Press down the ONT power btton. If the power indicator LED is ON, the ONT is powered on normally. Planning Data Before setting p the configration environment, prepare the data as shown in Table Version: A/1

21 3 Web Configration Gide Table 3-1 Item Planning Data for Logging into the Web GUI Locally Description Factory defalt vale: Administrator 4 Username: admin 4 Password: admin Common ser Username and password Management IP address and sbnet mask of the ONT The IP address and the sbnet mask of the ser compter 4 Username: ser 4 Password: ser1234 Note: Some operators have cstomized sername and password, so that the defalt sername and password may be different from the ones mentioned above. In this case, ask local operator for the administrator information. For common sers, please refer to the User Gide attached to the device or the label at the bottom of the device. Note: The password is case sensitive. Factory defalt vale: IP address: Sbnet mask: Note: Some operators reqire cstomized management IP address, so that the defalt management IP address may be different from the one mentioned above. In this case, please refer to the User Gide attached to the device or the label at the bottom of the device. Set this item to obtaining IP address atomatically (recommended) based on DHCP. Set this item to static IP address, which shold be in the same network segment with the management IP address of the ONT. 4 IP address: X (X is a decimal integer between 2 and 253) 4 Sbnet mask: Operation Procedre 1. Set the IP address and the sbnet mask of the compter. 4 The operations on the Windows 7 operating system are as follows: Version: A/1 15

22 AN A GPON Optical Network Terminal Prodct Manal a) In the Windows taskbar, select StartíControl Panel and click Network and Sharing Center. b) Click Local Area Connection to bring p the Local Area Connection Stats dialog box, and click Properties. c) In the Local Area Connection Properties dialog box that appears, doble-click Internet Protocol Version 4 (TCP/IPv4). 16 Version: A/1

23 3 Web Configration Gide d) In the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box that appears, set the IP address and sbnet mask of the compter. (See Table 3-1 for the detailed vales). Version: A/1 17

24 AN A GPON Optical Network Terminal Prodct Manal e) Click the OK btton to save the configration. 4 The operations on the Windows XP operating system are as follows: a) In the Windows taskbar, select StartíControl Panel. Doble-click Network Connection to enter the network connection window. b) Right-click Local Connection and select Properties from the shortct men to bring p the Local Connection Properties dialog box. c) Doble-click Internet Protocol (TCP/IP). In the Internet Protocol (TCP/IP) Properties dialog box that appears, set the IP address and sbnet mask of the compter. (See Table 3-1 for the detailed vales). 18 Version: A/1

25 3 Web Configration Gide d) Click the OK btton to save the configration. 2. Enter (defalt management IP address of the ONT) in the browser address bar of the compter, and press the Enter key to bring p the ser login dialog box. 3. Enter the administrator sername and password in the login dialog box. Access the Web GUI after the password is athenticated. Cation: The system will log ot atomatically if no operation is performed in five mintes. Web Configration GUI Layot The Web configration GUI comprises three parts, as shown in Figre 3-1. Navigation bar. Click the link to enter the corresponding configration management page. Link bar. Click the link to enter the sb-page for corresponding configration management. Version: A/1 19

26 AN A GPON Optical Network Terminal Prodct Manal Configration management area. Displays the contents of the selected navigation bar and link bar. (1) Navigation bar (2) Link bar (3) Configration management area Figre 3-1 Web Configration GUI Note: The screenshots provided here are for reference only, and the actal Web GUIs for the eqipment shall prevail. The configration GUI for the administrator is different from that for common sers: The administrator can view and configre all the node items in the Web GUI. The common sers can view and configre only part of the node items. The following lists the key nodes available for common sers. The configration items actally available in the Web GUI for common sers shall prevail. 4 The Stats tab. 4 User Accont and Device Reboot in the Management tab. 3.2 Stats The following introdces how to view basic information abot the ONT, inclding the device information, WAN side stats, LAN side stats and optical power stats, etc. 20 Version: A/1

27 3 Web Configration Gide Device Information Select Stats in the navigation bar, and select Device InformationíDevice Information in the left link bar to view the information sch as the software version, hardware version, device model and device description. See Figre 3-2. Figre 3-2 Device Information WAN Side Stats Select Stats in the navigation bar and select Wan StatsíWan Stats in the left link bar to view the information sch as the stats, IP obtaining mode, IP address and sbnet mask of the WAN interface. See Figre 3-3. Figre 3-3 WAN Side Stats LAN Side Stats Check the stats information abot the LAN interface and the DHCP client end. Version: A/1 21

28 AN A GPON Optical Network Terminal Prodct Manal LAN Side Stats Select Stats in the navigation bar and select Lan StatsíLan Stats in the left link bar to view the information sch as the IP address, sbnet mask of the LAN side. See Figre 3-4. Figre 3-4 LAN Side Stats DHCP User List Select Stats in the navigation bar and select Lan StatsíDHCP Clients List in the left link bar to view the information abot the DHCP client end sch as the IP address, MAC address and hired time. See Figre 3-5. Figre 3-5 DHCP User List Optical Power Stats Select Stats in the navigation bar and select Optical InfoíOptical Info in the left link bar to view the optical modle information sch as the Tx optical power, Rx optical power and working temperatre. See Figre Version: A/1

29 3 Web Configration Gide Figre 3-6 Optical Power Stats 3.3 Network The following introdces how to configre the LAN, broadband, DHCP server and athentication in the Web GUI LAN Settings Configre the management IP address and sbnet mask at the LAN side. 1. Select Network in the navigation bar and select LAN SettingsíLAN Settings in the left link bar to open the LAN settings page, as shown in Figre 3-7. Version: A/1 23

30 AN A GPON Optical Network Terminal Prodct Manal Figre 3-7 LAN Settings 2. Configre the management IP address and sbnet mask at the LAN side. See Table 3-2 for the parameter description. 3. Click Apply to save and apply the configration. Table 3-2 Item Parameters of LAN Settings Description IP address Sbnet Mask IPv6/Prefix Managed Flag Other Config Flag Max RA interval Min RA interval The management IP address at the LAN side of the ONT. The defalt vale is The sbnet mask of the ONT for the LAN. The defalt vale is The IPv6 gateway address, inclding a prefix of 64 bits. The defalt vale is fe80::1/64. Select whether to distribte the IPv6 address based on DHCP. The defalt vale is Disable. Select whether to distribte the IPv6 DNS information based on DHCP. The defalt vale is Enable. The maximm interval for annoncing the gateway information. The defalt vale is 10. The minimm interval for annoncing the gateway information. The defalt vale is Version: A/1

31 3 Web Configration Gide Table 3-2 Item DNS sorce Prefix mode Parameters of LAN Settings (Contined) Description The sorce of the DNS distribted to PC, inclding WAN connection, ONT proxy and static configration. The defalt vale is WAN connection. The sorce of the prefix information distribted to PC, inclding WAN connection and static configration. The defalt vale is WAN connection. Enable DHCP6S Start IPv6 Address End IPv6 Address Sets whether to enable the DHCPv6 server. This item shold be selected if Managed Flag or Other Config Flag is selected; otherwise the IP address or DNS information cannot be distribted. Enabled by defalt. The starting address ID of the address pool for distribtion of DHCPv6 IP addresses. The defalt vale is 0:0:0:2. The ending address ID of the address pool for distribtion of DHCPv6 IP addresses. The defalt vale is 0:0:0: Broadband Settings Select different WAN connections for different network environment, or configre corresponding parameters for the selected WAN connection. 1. Select Network in the navigation bar and select BroadBand Settingsí Internet Settings in the left link bar to open the Internet settings page, as shown in Figre 3-8. Figre 3-8 Internet Settings Version: A/1 25

32 AN A GPON Optical Network Terminal Prodct Manal 2. Configre parameters relevant to the Internet at the WAN side. Table 3-3 introdces the parameters. 3. Click Apply to save and apply the configration. Table 3-3 Parameters for Internet Settings Item Service Type Connection Type Description Select the WAN port service type. TR069: this connection is only applicable for TR069. INTERNET: this connection is only applicable for Internet access. TR069_INTERNET: this connection is applicable for both TR069 and Internet access. VOIP: this connection is only applicable for voice application. VOIP_INTERNET: this connection is applicable for voice and Internet access. OTHER: other connections. Select the connection type of the WAN port. Bridge: the Layer 2 bridge connection mode. This connection mode can be sed when the service type is set to INTERNET, IPTV or OTHER. Rote: the Layer 3 roter connection mode. This connection mode can be sed when the service type is set to INTERNET, IPTV or OTHER. VLAN ID Sets the VLAN ID of the WAN connection. The vale ranges from 1 to The VLAN ID vale here shold be consistent with that on the ser side of the OLT. COS Sets the priority of the VLAN. The vale ranges from 0 to 7. NAT Enables or disables the NAT fnction. Users need to configre DNS Relay Enables or disables the DNS relay fnction. this item when the service type is set to TR069_INTERNET or VOIP_INTERNET. Users need to configre MTU Enter the maximm transmission nit. It is advised to se the this item when the service defalt vale. type is set to INTERNET or OTHER and the connection type is set to Rote. LAN Binding Select the LAN port to be bond with the WAN port. 26 Version: A/1

33 3 Web Configration Gide Table 3-3 Parameters for Internet Settings (Contined) Item IP Mode WAN IP Mode User Name Password Operation Mode IP Address Sbnet Mask Defalt Gateway Primary DNS Server Secondary DNS Server Description The options inclde IPv4&IPv6, IPv4 and IPv6. Sets the IP address obtaining mode at the WAN side of the ONT. The options inclde DHCP, static and PPPoE. DHCP: Obtaining the IP address dynamically. Static: Setting the IP address in a static mode. PPPoE: PPPoE dialing mode. Enter the sername provided by ISP. Enter the password provided by ISP. Sets the PPPoE connection mode. The defalt setting is "Keep Alive". Enter the static IP address at the WAN side provided by ISP. Enter the sbnet mask provided by ISP. Enter the defalt gateway provided by ISP. Enter the IP address of the active DNS server provided by ISP. Enter the IP address of the standby DNS server provided by ISP. Users need to configre this item when the service type is set to TR069_INTERNET or VOIP_INTERNET. Users need to configre this item when the service type is set to INTERNET or OTHER and the connection type is set to Rote. This item shold be set if the connection type is Rote. This item shold be set if the WAN IP Mode is set to PPPoE. This item shold be set when the IP Mode is set to IPv4&IPv6 or IPv4 and the WAN IP Mode is set to static. Version: A/1 27

34 AN A GPON Optical Network Terminal Prodct Manal Table 3-3 Parameters for Internet Settings (Contined) Item IPv6 Address IPv6 Prefix Length Defalt Gateway Primary DNS Server Secondary DNS Server IPv6 Address Mode / IPv6 Prefix Mode Description Enter the static IPv6 address at the WAN side provided by ISP. Enter the static IPv6 address prefix length at the WAN side provided by ISP. Enter the defalt gateway provided by ISP. Enter the IP address of the active DNS server provided by ISP. Enter the IP address of the standby DNS server provided by ISP. Select the IPv6 address obtaining mode / prefix obtaining mode. This item shold be set when the IP Mode is set to IPv4&IPv6 or IPv6 and the WAN IP Mode is set to static. This item shold be set when the IP Mode is set to IPv4&IPv6 or IPv6 and the WAN IP Mode is set to DHCP or PPPoE DHCP Server Using the DHCP fnction, the ONT can distribte the network parameters (sch as IP address, gateway and DNS server IP address) to the devices (sch as compter) within the LAN. Users can manage the IP addresses collectively sing this fnction. 1. Select Network in the navigation bar, and then select DHCP ServeríDHCP Service from the left link bar to open the DHCP server configration page, as shown in Figre Version: A/1

35 3 Web Configration Gide Figre 3-9 DHCP Service 2. Configre the DHCP server parameters as reqired. Table 3-4 describes the parameters. 3. Click Apply to save the configration information. The configration will take effect after the ONT is rebooted. Table 3-4 Parameters for the DHCP Server Item Classification Description Enables or disables the DHCP server. Server: Enables the DHCP server. The ONT can dynamically distribte IP addresses to ser terminals. Disable: The ser terminals connected to the ONT cannot obtain the private network IP address sing the DHCP. DHCP Start IP DHCP End IP DHCP Sbnet Mask DHCP Primary DNS DHCP Secondary DNS The starting IP address of the IP address pool for the active DHCP server. The ending IP address of the IP address pool for the DHCP server. The mask of the active DHCP server. The IP address of the active DNS server. The IP address of the standby DNS server. Note: The IP address set here shold be in the same network segment with the IP address set in LAN Settings; otherwise, the DHCP server will not operate normally. Version: A/1 29

36 AN A GPON Optical Network Terminal Prodct Manal Table 3-4 Parameters for the DHCP Server (Contined) Item DHCP Defalt Gateway DHCP Lease Time Option60 Description The defalt gateway of the active DHCP server. The lease time of the IP address pool of the DHCP server. Enables or disables the Option 60 property to identify the ser terminal. Option 60 start IP Option 60 end IP The starting IP address of the network segment distribted to the Option 60 property terminal by the DHCP server. The ending IP address of the network segment distribted to the Option 60 property terminal by the DHCP server. This item shold be configred when the Option 60 field of the DHCP server is enabled Athentication Setting Configre the parameters relevant to the ONT athentication mode, so that the ONT can pass the OLT athentication. 1. Select Network in the navigation bar and select AthenticationíOLT Athentication in the left link bar to open the OLT athentication configration page, as shown in Figre Figre 3-10 OLT Athentication 2. Configre the parameters as reqired. Table 3-5 describes the parameters. 3. Click Apply to save the configration information. The configration will take effect after the ONT is rebooted. 30 Version: A/1

37 3 Web Configration Gide Table 3-5 Item Parameters for OLT Athentication Description LOID Sets the LOID ser name. This item is configrable Logic Password Sets the LOID password. when the ONT ses the LOID athentication mode. Sets the athentication password when the ONT is athenticated by Password Ath password. 3.4 Secrity The following introdces how to configre the firewall, remote control, dynamic DoS and HTTPS in the Web GUI Firewall The firewall configration incldes Firewall Control IPv4 Filtering IPv6 Filtering URL Filtering DHCP Filtering Anti-port Scan MAC Filtering IPv6 MAC Filtering Firewall Control Enabling the firewall can prevent malicios access to the WAN port of the ONT. 1. Select Secrity in the navigation bar and select FirewallíFirewall Control in the left link bar to open the firewall enabling page, as shown in Figre Version: A/1 31

38 AN A GPON Optical Network Terminal Prodct Manal Figre 3-11 Firewall Enabling 2. Select to Enable or Disable the firewall as reqired. 3. Click Apply to save and apply the configration IP Filtering Allow or forbid the incoming or otgoing flow of the IP packets that comply with the filtering conditions. After the firewall is enabled, the pre-set rles will take effect. 1. Select Secrity in the navigation bar and select FirewallíIPv4 Filtering in the left link bar. Click Add to open the filtering rle list configration page, as shown in Figre Figre 3-12 IPv4 Filtering 32 Version: A/1

39 3 Web Configration Gide 2. Configre the parameters relevant to filtering as reqired. Table 3-6 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-6 Parameters for IP Address Filtering Item Filter Mode Description Select the filtering mode. Whitelist indicates that the data complying with the rles in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles in the filtering rle table will not be allowed to pass. After the aforesaid operation, click the Apply btton to validate the configration. Direction Src IP Src Port Dst IP Dst Port Protocol Sets the direction of the filtering rle. LAN->WAN: plink direction. WAN->LAN: downlink direction. Enter the IP address at the LAN side if the direction is LAN->WAN. Enter the IP address at the WAN side if the direction is WAN->LAN. The port range of the sorce IP address. This item is configrable when the Protocol is set to TCP or UDP. Enter the IP address at the WAN side if the direction is LAN->WAN. Enter the IP address at the LAN side if the direction is WAN->LAN. The port range of the destination IP address. This item is configrable when the Protocol is set to TCP or UDP. Protocol type, inclding TCP, UDP, ICMP and ALL IPv6 Filtering Allow or forbid the IPv6 packets that comply with the filtering condition to be transmitted from the LAN or transmitted into MAN. After the firewall is enabled, the pre-set rles will take effect. 1. Select Secrity in the navigation bar and select FirewallíIPv6 Filtering in the left link bar. Then click Add to open the IPv6 filtering rle list configration page, as shown in Figre Version: A/1 33

40 AN A GPON Optical Network Terminal Prodct Manal Figre 3-13 IPv6 Filtering 2. Configre the parameters relevant to filtering as reqired. Table 3-7 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-7 Item Uplink Parameters of IPv6 Filtering Description Select the plink filtering mode. Whitelist indicates that the data complying with the rles in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles in the filtering rle table will not be allowed to pass. After the aforesaid operation, click the Apply btton to validate the configration. 34 Version: A/1

41 3 Web Configration Gide Table 3-7 Item Downlink Direction Src IPv6 Src Port Dst IPv6 Dst Port Protocol Parameters of IPv6 Filtering (Contined) Description Select the downlink filtering mode. Whitelist indicates that the data complying with the rles in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles in the filtering rle table will not be allowed to pass. Sets the direction of the filtering rle. LAN->WAN: plink direction. WAN->LAN: downlink direction. Enter the IPv6 address at the LAN side if the direction is set to LAN->WAN. Enter the IPv6 address at the WAN side if the direction is set to WAN->LAN. The port range of the sorce IP address. This item is configrable when the Protocol is set to TCP or UDP. Enter the IPv6 address at the WAN side if the direction is set to LAN->WAN. Enter the IPv6 address at the LAN side if the direction is set to WAN->LAN. The port range of the destination IP address. This item is configrable when the Protocol is set to TCP or UDP. Protocol type, inclding TCP, UDP, ICMP and ALL URL Filtering By setting the URL filtering rles, sers can forbid or allow all the data packets sent to or received from a certain IP address. After the fire wall is enabled, the pre-set URL filtering rle will take effect, and the domain names that meet the filtering conditions will be filtered. 1. Select Secrity in the navigation bar and select FirewallíURL Filtering in the left link bar, and then click Add to open the URL filtering table configration page, as shown in Figre Version: A/1 35

42 AN A GPON Optical Network Terminal Prodct Manal Figre 3-14 URL Filtering 2. Configre the parameters relevant to filtering as reqired. Table 3-8 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-8 Item Enable Parameters for URL Filtering Parameters Description Enables or disables the URL filtering fnction. URL Blacklist / Whitelist URL Address Start Time End Time Select the filtering mode. The white list and black list modes are configred globally, and cannot be enabled simltaneosly. Whitelist indicates that the data complying with the rles defined in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles defined in the filtering rle table will not be allowed to pass. The URL address accessed by sers. The starting time of the filtering rle. The ending time of the filtering rle. After setting, click Apply below to take effect. Enable Enables or disables this filtering rle. The options inclde Disable and Enable. 36 Version: A/1

43 3 Web Configration Gide DHCP Filtering Forbid or allow the ser device configred with the MAC address to obtain an IP address in the DHCP mode to prevent DOS attacks. After the firewall is enabled, the pre-set rles will take effect. 1. Select Secrity in the navigation bar and select FirewallíDHCP Filtering in the left link bar. Then click Add to open the DHCP Filtering Table configration page, as shown in Figre Figre 3-15 DHCP Filtering 2. Configre the parameters relevant to filtering as reqired. Table 3-9 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-9 Item Parameters for DHCP Filtering Description DHCP Filtering Enable Enables or disables the DHCP filtering. After setting, click Apply below to take effect. Version: A/1 37

44 AN A GPON Optical Network Terminal Prodct Manal Table 3-9 Item Parameters for DHCP Filtering (Contined) Description DHCP Filtering Blacklist / Whitelist MAC Address Select the filtering mode. The white list and black list modes are global configration, which cannot be enabled simltaneosly. Whitelist indicates allowing the device configred with the MAC address to obtain the IP address sing the DHCP. Blacklist indicates forbidding the device configred with the MAC address to obtain the IP address sing the DHCP. The MAC address of the ser device sbject to the DHCP filtering rle Anti-port Scan Enable or disable the anti-port scan fnction. 1. Select Secrity in the navigation bar and select FirewallíAnti Port Scan in the left link bar to open the anti-port scan page, as shown in Figre Figre 3-16 Anti-port Scan 2. Select to Enable or Disable the anti-port scan fnction as reqired. 3. Click Apply to save and apply the configration MAC Address Filtering One ser device may have mltiple IP addresses bt only one MAC address. The ser device access athority in the LAN can be controlled effectively by setting the MAC address filtering. After the fire wall is enabled, the pre-set rles will take effect, and the MAC addresses that meet the filtering conditions will be filtered. 38 Version: A/1

45 3 Web Configration Gide 1. Select Secrity in the navigation bar and select FirewallíMAC Filtering in the left link bar, and then click Add to open the MAC address filtering table configration page, as shown in Figre Figre 3-17 MAC Filtering 2. Configre parameters relevant to filtering as reqired. Table 3-10 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-10 Item MAC Filtering Enable MAC Filtering Blacklist / Whitelist Parameters for MAC Address Filtering Description Enables or disables the MAC address filtering fnction. Select the filtering mode. The white list and black list modes are global configration, which cannot be enabled simltaneosly. Whitelist indicates that the data complying with the rles defined in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles defined in the filtering rle table will not be allowed to pass. After setting, click Apply below to take effect. MAC Address The MAC address in the MAC address filtering rle. Version: A/1 39

46 AN A GPON Optical Network Terminal Prodct Manal Table 3-10 Item Start Time End Time Enable Parameters for MAC Address Filtering (Contined) Description The starting time of the filtering rle. The ending time of the filtering rle. Enables or disables this filtering rle. The options inclde Disable and Enable IPv6 Mac Filtering One ser device may have mltiple IPv6 addresses bt only one MAC address. The ser device access athority in the LAN can be controlled effectively by setting the MAC address filtering. After the fire wall is enabled, the pre-set rles will take effect, and the MAC addresses that meet the filtering conditions will be filtered. 1. Select Secrity in the navigation bar and select FirewallíIPv6 MAC Filtering in the left link bar, and then click Add to open the page for configring the MAC address filtering table, as shown in Figre Figre 3-18 IPv6 Mac Filtering 2. Configre the parameters relevant to filtering as reqired. Table 3-11 describes the parameters. 40 Version: A/1

47 3 Web Configration Gide 3. Click Apply to save and apply the configration. Table 3-11 Item Parameters for IPv6 MAC Address Filtering Description MAC Filtering Enable MAC Filtering Blacklist / Whitelist MAC Address Start Time End Time Enables or disables the MAC address filtering fnction. Select the filtering mode. The white list and black list modes are global configration, which cannot be enabled simltaneosly. Whitelist indicates that the data complying with the rles defined in the filtering rle table will be allowed to pass. Blacklist indicates that the data complying with the rles defined in the filtering rle table will not be allowed to pass. The MAC address in the MAC address filtering rle. The starting time of the filtering rle. The ending time of the filtering rle. After setting, click Apply below to take effect. Enable Enables or disables this filtering rle. The options inclde Disable and Enable Remote Control Enable or disable the remote access control. If the remote control is disabled, the PCs in the Internet cannot access the Web GUI of the ONT sing the IP addresses at the WAN side; if enabled, the PCs in the Internet can access the Web GUI. 1. Select Secrity in the navigation bar and select Remote ControlíRemote Control in the left link bar to open the remote control configration page, as shown in Figre Figre 3-19 Remote Control 2. Enable or Disable the remote access control as reqired. Version: A/1 41

48 AN A GPON Optical Network Terminal Prodct Manal 3. Click Apply to save and apply the configration Dynamic DoS The DoS attack exhasts the resorce of target compter sing massive virtal information flow, so that the attacked compter has to handle the virtal information with all strength, which inflences the handling of normal information flow. The ONT provides the protection against the DoS attack. 1. Select Secrity in the navigation bar and select DDOSíDDOS in the left link bar to open the anti-dos attack configration page, as shown in Figre Figre 3-20 Dynamic DoS 2. Select to Enable or Disable the anti-dos attack fnction as reqired. 3. Click Apply to save and apply the configration HTTPS The ONT provides the HTTPS fnction. The HTTPS is the HTTP channel for secrity. It is bilt on the SSL+HTTP protocol, which can perform encryption transmission and identity athentication. 1. Select Secrity in the navigation bar and select HTTPSíHTTPS in the left link bar to open the HTTPS fnction configration page, as shown in Figre Figre 3-21 HTTPS 42 Version: A/1

49 3 Web Configration Gide 2. Select to Enable or Disable the HTTPS fnction as reqired. Cation: After enabling the HTTPS fnction, log into the Web GUI. The protocol type in URL shold be https and the management IP address shold be added with the port nmber 4433, e.g Click Apply to save and apply the configration. 3.5 Application The following introdces how to configre the DDNS, port forwarding, NAT, UPnP, DMZ and network diagnosis in the Web GUI DDNS The DDNS server transforms the dynamic IP address at the WAN side of the ONT into a static domain name. Users from Internet can easily access the gateway sing this domain name. 1. Select Application in the navigation bar and select DDNSíDDNS Settings in the left link bar to open the DDNS configration page, as shown in Figre Figre 3-22 DDNS Settings 2. Configre parameters relevant to DDNS according to the reqirement. Table 3-12 describes the parameters. 3. Click Apply to save and apply the configration. Version: A/1 43

50 AN A GPON Optical Network Terminal Prodct Manal Table 3-12 Item Username Password Host Parameters for DDNS Settings Description The sername allocated by the DDNS provider. The password allocated by the DDNS provider. The domain name allocated by the DDNS provider. WAN Interface DDNS Provider Name of the created WAN connection. The DDNS service provider. Users can select the preset DDNS provider or select Other to cstomize the provider and set the domain name, server IP address, protocol type and URL Port Forwarding The port forwarding can create the mapping between the WAN port IP address / common port nmber and the LAN server IP address / private port nmber. In this way, all the accesses to a certain service port at this WAN port will be re-directed to the corresponding port of the server in the designated LAN. 1. Select Application in the navigation bar and select Port ForwardingíPort Forwarding in the left link bar. Click Add to open the port forwarding configration page, as shown in Figre Figre 3-23 Port Forwarding 44 Version: A/1

51 3 Web Configration Gide 2. Configre parameters relevant to port forwarding according to the reqirement. Table 3-13 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-13 Item WAN Description Pblic Port IP Private Port Protocol Enable Parameters for Port Forwarding Description The corresponding WAN connection bond with the port forwarding rle. The port forwarding rle name. The range of ports for Extranet data packets. If only one port exists, enter the same port nmber. The IP address of the LAN virtal server for port forwarding. The range of the LAN port for port forwarding. If only one port exists, enter the same port nmber. The protocol sed for the port to forward data packets, inclding ALL, TCP and UDP. Enables or disables the rle NAT NAT allows the conversion between intranet IP addresses and pblic network IP addresses. NAT converts a great nmber of intranet IP addresses into one or a small nmber of pblic network IP addresses, so as to save the resorce of pblic network IP addresses. The NAT configration below can take effect only when the NAT fnction is enabled in NetworkíBroadBand SettingsíInternet Settings. 1. Select Application in the navigation bar and select NATíNAT in the left link bar. Click Add to open the NAT rle list configration page, as shown in Figre Version: A/1 45

52 AN A GPON Optical Network Terminal Prodct Manal Figre 3-24 NAT 2. Configre relevant parameters according to the reqirement. Table 3-14 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-14 Item WAN Description Rle Type Parameters for NAT Configration Description The corresponding WAN connection bond with the NAT rle. NAT rle name. Select the NAT conversion mode. It is advisable to select One-to-One or Many-to-One. Locate Start IP Locate End IP Pblic Start IP Pblic End IP The starting IP address of intranet. The ending IP address of intranet. The starting IP address of the pblic network. The ending IP address of the pblic network. 46 Version: A/1

53 3 Web Configration Gide UPnP The UPnP spports the plg and play fnction and the atomatic discovery fnction of mltiple network devices. When UPnP is enabled, the devices that spports UPnP can be added into the network dynamically. In this way, an external compter can access the resorce on the internal compter when necessary. For example, when some application software are rnning on a PC, the port mapping table will be generated on the ONT atomatically sing the UPnP protocol, so that the operation can be sped p. 1. Select Application in the navigation bar and select UPNPíUPNP in the left link bar to open the UPnP configration page, as shown in Figre Figre 3-25 UPnP 2. Select to Enable or Disable the UPnP fnction as reqired. 3. Click Apply to save and apply the configration DMZ When the ONT is working in the roting mode, sers shold enable the DMZ fnction if a host at the WAN side needs to access a certain host at the LAN side. The ONT will forward all the IP packets from the WAN to the designated DMZ host. 1. Select Application in the navigation bar and select DMZíDMZ in the left link bar to open the DMZ configration page, as shown in Figre Version: A/1 47

54 AN A GPON Optical Network Terminal Prodct Manal Figre 3-26 DMZ 2. Configre relevant parameters according to the reqirement. Table 3-15 describes the parameters. 3. Click Apply to save and apply the configration. Table 3-15 Item DMZ Enable DMZ Host IP Parameters for DMZ Configration Description Enables or disables the DMZ fnction. The options inclde Enable, Disable and Ato. If Enable is selected, the DMZ host IP address shold be set. If Ato is selected, the DMZ host ses the first IP address allocated by DHCP. The host IP address of the DMZ Network Diagnosis Network diagnosis incldes network diagnosis and Nat conversation Network Diagnosis The ONT provides two network diagnosis tools. Ping test: Test whether the roter is normally connected with the target host or another device. Tracerote test: Check the roting condition from the roter to the target host. 1. Select Application in the navigation bar and select DiagnosisíDiagnosis in the left link bar to open the network diagnosis page, as shown in Figre Version: A/1

55 3 Web Configration Gide Figre 3-27 Network Diagnosis 2. Enter the destination IP address to be tested in the Destination Address box, and click Ping or Tracerote to test. The test reslt will be displayed in the lower text box Nat Session Click Application and select DiagnosisíNat Session at the left side to open the Nat session page and qery the mappings between the inner / oter network IP address of NAT and the ports, as shown in Figre Version: A/1 49

56 AN A GPON Optical Network Terminal Prodct Manal Figre 3-28 Nat Session 3.6 Management The following introdces how to perform accont management, device management and log management in the Web GUI Accont Management Accont management incldes ser accont management and maintenance accont management User Accont Management Users can add or delete a common ser accont or modify the password of a common ser accont. 1. Select Management in the navigation bar. Select Accont Managementí User Accont from the left link bar to open the ser accont management page, as shown in Figre Version: A/1

57 3 Web Configration Gide Figre 3-29 User Accont Management 2. Add or delete a common ser accont or modify the password of a common ser accont as reqired. 3. Click Apply to save and apply the configration Maintenance Accont Management Users can modify the sername and password of the crrent accont. 1. Select Management in the navigation bar. Select Accont Managementí Maintenance Accont from the left link bar to open the maintenance accont management page, as shown in Figre Figre 3-30 Maintenance Accont Management 2. Modify the sername and password of the crrent accont as reqired. 3. Click Apply to save and apply the configration. Version: A/1 51

58 AN A GPON Optical Network Terminal Prodct Manal Device Management The ONT provides mltiple device management fnctions sch as restoring some of the configration data, restoring all configration data, local pgrade, configration backp, device reboot, and NTP time calibration Restoring the Configration Data Restore factory settings of the ONT, inclding ser name and password for Web login, SSID and password for wireless network, etc. 1. Select Management in the navigation bar. Select Device Managementí Restore from the left link bar to open the configration restoring page, as shown in Figre Figre 3-31 Restoring the Configration Data 2. Click Restore and then click OK in the alert box that appears. Wait ntil the configration data are completely restored Restoring All the Configration Restore all the configration data of the ONT to factory settings. 1. Select Management in the link bar and select Device ManagementíRestore All on the left side to open the configration restoration page, as shown in Figre Figre 3-32 Restoring All the Configration 52 Version: A/1

59 3 Web Configration Gide 2. Click Restore All and then click OK in the alert box that appears. Wait ntil the configration data are completely restored Local Upgrade Select the local file and pgrade the ONT software. Dring pgrade, do not power off the device or perform other operations to prevent damage to the device. 1. Select Management in the navigation bar. Select Device Managementí Local Upgrade from the left link bar to open the local pgrade page, as shown in Figre Figre 3-33 Local Upgrade 2. Click Browse. In the dialog box that appears, select the device software version to be pgraded and click Open to pgrade the ONT software version. 3. When the pgrade scceeds, the page will prompt for device rebooting. Click "Reboot". After rebooting, the device will be pgraded to the new version. Note: After the pgrade, sers can view the Software Version in the device information page to check whether the crrent version is correct Configration Backp Back p and save the ONT configration files for restoring the configration data later on. Before backp, enable the FTP tool in the compter. 1. Select Management in the navigation bar. Select Device Managementí Config Backp from the left link bar to open the configration backp page, as shown in Figre Version: A/1 53

60 AN A GPON Optical Network Terminal Prodct Manal Figre 3-34 Configration Backp 2. Configre parameters relevant to file backp. Table 3-16 describes the parameters. 3. Click Apply to save the configration backp file. Table 3-16 Item Username Password Localhost IP File name Parameters for Configration Backp Description The FTP sername. The FTP password. Local IP address. The existing file name in the ONT Device Reboot 1. Select Management in the navigation bar. Select Device Managementí Device Reboot from the left link bar to open the device reboot page, as shown in Figre Figre 3-35 Device Reboot 2. Click Reboot and click OK in the alert box that appears and wait for the device to reboot. 54 Version: A/1

61 3 Web Configration Gide Cation: Save the configring data before rebooting the device to prevent loss of the configration data. After the device is rebooted, yo need to wait for abot two mintes to relog into the Web GUI of the device NTP Time Calibration Users can obtain the precise time by connecting the ONT to a NTP server. 1. Select Management in the navigation bar. Select Device ManagementíNTP Check Time from the left link bar to open the NTP check time page, as shown in Figre Figre 3-36 NTP Time Calibration 2. Configre parameters relevant to the NTP time calibration. Table 3-17 describes the parameters. 3. Click Check Time to save and apply the configration. Table 3-17 Item Parameters for NTP Time Calibration Description Enable NTP Check Time seconds First NTP Server Select whether to enable the NTP time calibration fnction. Sets the time interval for synchronization with the time server. Enter the IP address of the active NTP server. Version: A/1 55

62 AN A GPON Optical Network Terminal Prodct Manal Table 3-17 Item Second NTP Server Time Zone Crrent Time Binding WAN Connections Parameters for NTP Time Calibration (Contined) Description Enter the IP address of the standby NTP server. Select the time zone according to the location of the device. When NTP Check Time is enabled, time will be calibrated according to the eqipment location, and the local time will be displayed. When NTP Check Time is disabled, the system initial time ( ) or the previos calibrated time will be displayed. Select the WAN connection type for time calibration Log Management The Log files record key operations and actions on the ONT. Users can view the information saved in log as needed. Select Management in the navigation bar. Select LogíLog from the left link bar to open the log information page, as shown in Figre Figre 3-37 Log 56 Version: A/1