Avaya. Installation Guide M2-1000SX/LX 1000BASE-SX/1000BASE-LX GIGABIT/FAST ETHERNET SWITCHING MODULES FOR THE AVAYA M770

Transcription

1 Avaya Installation Guide M2-1000SX/LX 1000BASE-SX/1000BASE-LX GIGABIT/FAST ETHERNET SWITCHING MODULES FOR THE AVAYA M770 Catalog No Rev. A. July, 2001

2

3 Chapter 1 Overview Description This installation guide is divided into the following main sections: Overview: A general description of the Avaya s M2-1000, including interfaces, LED indicators and a front panel illustration. Installation: Step-by-step instructions for configuring the hardware, calculating domain usage, and installing the M in an Avaya M770 Multifunction Switch. Software Configuration: Instructions for navigating the M setup menus and step-by-step instructions for performing basic setup operations of the M module. Troubleshooting: Suggested solutions for commonly encountered problems. Appendix: Port connector pin assignments. The M is a 2-port full-duplex 1000BASE-SX/1000BASE-LX Gigabit and 6- port 10BASE-T/100BASE-TX Fast Ethernet DomainX module for insertion into the Avaya M770 hub. The following table describes SX, LX standards: Standard Wavelength Cable type Distance 1000BaseSX 850 nm 62.5 µm 220 m 1000BaseSX 850 nm 50 µm 550 m 1000BaseLX 1300 nm 10 µm 5 km 1000BaseLX 1300 nm 62.5 µm 500 m The Avaya M770 supports two Frame Switches, named DomainXs: DomainXL (Left DomainX) spans slots 1-7, and DomainXR (Right DomainX) spans slots Each DomainX supports up to 6 Gbytes of bandwidth. You can insert the M into either DomainX, provided you don t exceed the maximum of 100 Domain Resource Units (DRUs) per DomainX. Each module uses a certain number of DRUs; the M uses 15 DRUs. The M module s two Gigabit Ethernet ports can operate in two modes: Standard 802.1Q VLAN tagging mode (default mode). Global VLAN is automatically set on the ports when in this mode. Per port only mode (for use without VLAN tagging). You can select a separate VLAN for each Gigabit port. M2-1000SX/LX Installation Guide 1

4 Chapter 1 Overview Note: The VLAN tagging mode (802.1Q) or per port only must be the same on both local and remote ports. The M gigabit ports operate with autonegotiation disabled and any connected equipment must have the same setting. The Gigabit ports are identical and can be used to provide redundant Gigabit backbone links, using the software port redundancy definitions. The Gigabit ports conform to the 802.3x Gigabit flow control standard and operates in full-duplex mode. Each of the module s 6 Fast Ethernet ports can work at 10BASE-T/100BASE-TX speed. Each of these ports can also be configured to function in either half or full duplex mode. You can specify for each port the 10/100M speed and half/full duplex mode, or choose to use auto-negotiation. Auto-negotiation automatically determines the individual port s optimal mode of operation - 10/100M speed and half/full duplex. Note: The default settings for the 1 Gigabit ports are: Autonegotiation: Disabled Flow Control: Full Duplex: In addition, Avaya s top-performing congestion management means that no packets are lost, reducing the need for bandwidth-wasting retransmission. The M is manageable under CajunView, Avaya s family of SNMP network management systems, or any other SNMP-based management system. Note: The name M is used throughout this manual and refers to both the M2-1000SX and the M2-1000LX. 2 M2-1000SX/LX Installation Guide

5 Chapter 1 Overview Front Panel Components LED Indicator OPR USW Table 1 Description State Meaning Module Operational Status Use Switches Mode OFF Blink OFF Function LED 1 Port LED (1 8) LNK Port Status OFF 1 Blink COL Tx Rx FDX FC Collision Status Transmit to line Receive from line Full Duplex Mode Flow Control Mode OFF OFF OFF OFF OFF 100 Speed OFF Module is OK Module is not operational Module not connected to DomainX or DRU overflow problem. M Front Panel Diagnostic LEDs Use main circuit board DIP switch settings. Disregard main circuit board DIP switch settings. Port is enabled and Link OK Port is disabled Link Test failure 2 Collision occurred on line No collision 3 Data transmitted to line No activity on port Data received from line No activity on port Port in Full Duplex mode 4 Port in Half Duplex mode Port Flow Control is enabled Port Flow Control is disabled Port is operating at 100M speed Port is operating at 10M speed 3 1 Use the and pushbuttons on the front panel to select the Function to be displayed on the Port LEDs 2 In the case of the Gigabit link, this occurs because a cut in the cable 3 Always OFF for the Gigabit port 4 Always for the Gigabit port. M2-1000SX/LX Installation Guide 3

6 Chapter 1 Overview Table 2 M Front Panel Ports Port/Connector Function 1 2 The gigabit ports (SC connectors) of the M2-1000SX have a range of m (depending on the connecting cable bandwidth) and those of the M2-1000LX have a range of 5 km (on a 10 µm cable) BASE-T/100BASE-TX ports with RJ-45 connectors supporting a range of 100m. Resetting the Module To reset the module, press both the and pushbuttons simultaneously and hold for 2 seconds. 4 M2-1000SX/LX Installation Guide

7 Chapter 2 Installation Installation Overview There are several stages involved in the installation of the M2-1000: Hardware Configuration: Setting operation parameters via DIP switches on the module s circuit board. Domain Usage Considerations: Computing whether your intended configuration fits the Avaya M770 domain resources. Installing the Module: Inserting the module in the Avaya M770 hub, and connecting cables to the module s ports for connection to other equipment: switch, hub or station. Caution: The M contains components sensitive to electrostatic discharge. To prevent ESD damage, always hold the card by its sides only, and do not touch the circuit board components unless instructed to do so. Before handling the module or inserting it in the hub, touch the chassis of the hub to discharge any electrostatic charge on your body. Note: The recommended Avaya M770 configuration is two M-PS500 units, plus a third unit for redundancy. Such a configuration supports any number of DomainX and Avaya M400 Gate Switch modules in the hub. If there is only one M-PS500 unit available, the maximum number of modules in the hub is based on the following guidelines: 5 or less DomainX modules, or 4 DomainX modules with 2 or less Avaya M400 modules, or 3 DomainX modules with between 2 and 5 Avaya M400 modules. M2-1000SX/LX Installation Guide 5

8 OFF OFF P2 P1 P3 P4 P2 P1 P3 P4 Chapter 2 Installation Hardware Configuration Before installing the M module in the hub, you must configure the hardware by setting the appropriate DIP switches on the main and upper circuit boards. The following diagram shows the position of switches on the circuit boards. The illustration is oriented with backplane connectors to the right. Figure 1 M Circuit Boards with DIP Switches in Default Positions T_IMG SP Front Rear P5 P6 P7 P P5 P6 P7 P USW SPR2 SPR1 SPR0 1USW SPR2 SPR1 SPR T_IMG SP M2-1000SX/LX Installation Guide

9 Chapter 2 Installation Setting the DIP Switches The switches are shown in their actual location on the circuit board illustration. Do not touch or alter the unlabelled DIP switches and the SPR0 - SPR2 DIP switches. The functions of the switches are described below: Table 3 DIP Switches on Main Circuit Board SW# Name Function OFF Default 1 USW Use the Main circuit board DIP switch settings 2-4 SPR0 - SPR2 P1,P2 P3 - P8 Use DIP switches values Reserved for future expansion Reserved for future use (default OFF) Set port speed Set port speed to 10M Do not use DIP switches values Set port speed to 100M OFF OFF Note: When the USW switch is, port 10/100M speed and auto-negotiation cannot be set through management. When the USW switch is OFF, all other main circuit board DIP switch settings are ignored, and all configurable parameters can be set through management. Table 4 DIP Switches on Upper Circuit Board SW# Name Function OFF Default 1 SP For future use OFF 2 T_IMG Toggle between the two memory bank sources from which the module software is booted. This DIP switch should be used only if you lose your management connection to the module and need to change the default bank from which the module software is booted. To set a switch to, slide it in the direction shown by the arrow. Caution: Before changing DIP switch settings remove the module from the hub. M2-1000SX/LX Installation Guide 7

10 Chapter 2 Installation Domain Usage Considerations The M is a DomainX module of the Avaya M770. The maximum number of DomainX modules you can insert in the hub is determined by domain usage considerations, as follows (M-SPV refers to either the M-SPV or the M-SPX in the following examples): The Avaya M770 allows a maximum of 100 Domain Resource Units (DRUs) for DomainXL (Left DomainX - slots 1-7) and the M-SPV, and 100 DRUs for DomainXR (Right DomainX - slots 8-14) and the M-SPV. Each of the DomainX modules, as well as the M-SPV module, has a DRU budget, as shown in the table below. When planning your hub configuration, calculate whether it fits the Avaya M770 DRU budget. Table 5 Avaya M770 Module DRU Budget Module Name DRU Budget M-SPV/M-SPX 10 DRUs M12-100T 18 DRUs M12-100F 18 DRUs M DRUs M-MLS 6 DRUs M14-10F 6 DRUs Budget Calculation Examples 1. If you have six M14-10F modules, an M module and the M-SPV you get: 6* = 61 DRUs. Assuming that you have the same configuration on the DomainXL and Domain XR switches you get a total of 168 Ethernet, 12 Fast Ethernet and 4 Gigabit ports. 2. If you have five M modules and the M-SPV you get: 5*18+10 = 100 DRUs. Assuming that there are five modules on both the DomainXL and Domain XR switches you get a total of 120 ports. 3. If you have six M modules and the M-SPV you get: 6*15+10=100 DRUs. Assuming that there are six modules on both the DomainXL and Domain XR switches you get a total of 24 Gigabit Ethernet ports and 72 Fast Ethernet ports. 4. If you have four M modules, one M and the M-SPV/M-SPX you get: 4* =97 DRUs. This is less than 100 DRUs and is therefore another possible configuration. Note: A redundant M-SPV does not count in the DRU calculations. However you must include the active M-SPV twice, once for DomainXL and once for DomainXR. 8 M2-1000SX/LX Installation Guide

11 Chapter 2 Installation DRU Budget Information Window You can check the DRU budget information for your Avaya M770 hub via the CajunView Network Management System (NMS). The following window shows an example of a hub with an M-SPV, 2 M12-100T and an M12-100F module. Figure 2 DRU Budget Information Window M2-1000SX/LX Installation Guide 9

12 Chapter 2 Installation Installing the Module The M occupies one slot in the Avaya M770 chassis and can be inserted into any available position. The M can be installed or removed while power on. To install the M2-1000: 1. Hold the module (shaped like an upside down L) using both hands. The colored module name panel and LEDs should be on top (see Figure 3). 2. Fold out the plastic handles on the top and bottom of the front panel. 3. While holding the module by its handles, place it onto the top and bottom guide rails in the hub and gently slide it in. 4. Plug in the module by pressing firmly on the mid-section of the front panel. Fold down the handles and secure the module using the two screws at the top and bottom of the front panel. Do not over-tighten the screws. Note: Even though the modules are hot-swappable a short self initialization period is required when inserting or removing them from the hub. Allow at least 5 seconds initialization time between modules when inserting or removing several modules. 10 M2-1000SX/LX Installation Guide

13 Chapter 2 Installation Figure 3 Inserting the Module into the Hub Upper Guide Rails DomainX Module Avaya M770 Multifunction Switch Plastic Handle Module Name and LEDs Panel Plastic Handle Motherboard Connector Lower Guide Rails Power-on Check When you plug in the M2-1000, the OPR LED blinks for a short interval. Wait until it lights steadily before commencing work. M2-1000SX/LX Installation Guide 11

14 Chapter 2 Installation 12 M2-1000SX/LX Installation Guide

15 Chapter 3 Software Configuration Software configuration is divided into the following sections: Navigating the Setup Menus: Instructions for navigating the M setup menus. Parameters Configuration: Step-by-step instructions for performing basic setup operations of the M module. Navigating the Setup menus All Setup menus conform to the following display conventions: This symbol Means... This item has a sub-menu. [ ] This item has a sub-menu in which you can insert parameter values. 1, 2, 3, etc. Denotes a sequence number. To select an item from any menu, type its sequence number. Setup sub-menus display the following standard functions: This function Return to Previous Menu List Save the Session Reset the Module Means Go up one menu level. List the current values for the selected parameter. Save and store changes to the selected parameter, and activate changes. Changes become active immediately after the Save, and are stored in the M s NV-RAM. A reset is needed only when setting defaults to factory settings and for activating the new downloaded software. In all other cases, the M activates the new parameter values after you choose the Save the Session option. Note that the Reset affects the M only. M2-1000SX/LX Installation Guide 13

16 Chapter 3 Software Configuration If you forget to save changes or reset the M when necessary, the following warnings will remind you to do so before exiting the software Setup session: This WARNING * No save since last change. Save? y/[n]: Means Type <y> to save parameter changes. * IP address was changed. Reset the agent!!! The M must be reset in order to activate IP changes. Parameters Configuration After the M enters setup mode, the initial screen of the setup session automatically displays. It shows information about the agents in the Avaya M770 hub and which modules they manage. A screen similar to the following displays: Hub Main Menu <CR> Refresh the screen Select an Agent to configure: 1. Direct Access to a specific module 2. M-SPV in slot: 15 manages modules: 1, 2, 5, 7, 8, 10, 13, 14, 16 >>>Enter your choice: 1 >>>Enter module s slot number (1..16): 1 Avaya M770 Hub Main Menu When you choose Option 1 and enter the M slot number, you reach the M s Setup Main Menu. 14 M2-1000SX/LX Installation Guide

17 Chapter 3 Software Configuration Module Setup Main Menu Setup Main Menu M S/W Version: Slot #: 1 <CR> Refresh the screen 0. Return to Previous Menu Reset the Module 2. Software Download 3. Set Primary Version 4. Set factory defaults >>>Enter your choice: Module Setup Main Menu The module Setup Main Menu lists the various categories of M configurable parameters. You have 4 options: module reset, software download software, return to default factory settings and set the application to load after the next reset (primary version). Reset the Module Before exiting a Setup session, select the option Reset the Module from the Setup Main Menu if you wish the parameter changes you made to take effect. You will be asked to confirm the reset before it is executed. Note: The Reset the Module option does not reset the entire hub; it resets the selected module only. Software Download Software is downloaded using the TFTP/IP protocol. To enable the process, make sure there s a reachable TFTP server in the network. To download a software update to the M2-1000, use the Software Download option (option 2 from the Setup Main Menu). A screen similar to the following displays: M2-1000SX/LX Installation Guide 15

18 Chapter 3 Software Configuration Software Download parameters (Using TFTP/IP). M S/W Version: Slot #: 1 <CR> Refresh the screen 0. Return to Previous Menu 1. Save the Session 2. List TFTP Server and File parameters Start Software Download process 5. Monitor software download process... >>>Enter your choice: Software Download Menu Entering Software Download Parameters Select option 3 to enter the TFTP server, file and version parameters. The following prompts are displayed, with the current parameters displayed in every line: TFTP Server IP address: File Name: /home3/users/gk/vx/960cf/m21000f Downloaded file will override the old version (0.0.0) >>>Enter Server IP address [nnn.nnn.nnn.nnn]: >>>Enter File Name: c:\mng\agents\m21000f >>>Override version: 1 - (Version 2.0.1), [2 - (Version 1.0.6)]: 2 1. Enter the TFTP Server IP address. 2. Enter the file name of the new software version (full path). 3. Enter the version you wish to overwrite. The M stores two software versions. It is recommended that you overwrite the oldest version. See the version number to find out which is the oldest version. 16 M2-1000SX/LX Installation Guide

19 Chapter 3 Software Configuration 4. If you wish the M to load and run the new software version, select option Set Primary Version (option 4) from the Setup Main Menu. The new software version is automatically changed to the Primary version (refer to section Set Primary Version) and will be active following the next reset. Note: The M does not perform a reset after the software download process. To reboot, select the Reset the M option from the Setup Main Menu. Starting the Software Download Process To start the software download process, select option number 4 in the Software Download menu. You are queried whether to start the software download. Answer Y for the download to start. Monitoring the Software Download Process To monitor the software download process, select option number 5 in the Software Download menu. The download state, activity status, and downloaded size display on the screen. M S/W Version: Slot #: 1 TFTP Server IP Address: File Name: /home3/users/gk/vx/960cf/m21000f Destination: Flash Bank B (Application) Download State: tftp-running-ip Activity Status: Testing... Downloaded size: <CR> Refresh the screen. 0. Return to Previous Menu >>>Enter your choice: For troubleshooting the software download process, refer to Section Software Download Troubleshooting in Chapter 4. M2-1000SX/LX Installation Guide 17

20 Chapter 3 Software Configuration Set Defaults to Factory Settings You can set the M s configuration back to its default factory settings by selecting item number 3 in the Module Setup Main Menu. The following confirmation and warning messages are displayed: *** Set default values ***, Confirm [y/n]?y ***WARNING*** - Management parameters were changed. Reset the agent!! Set Defaults to Factory Settings Before exiting this session, select the option Reset the M from the Module Setup Main Menu. Set Primary Version The M stores two software versions. The version which is currently running is called the Primary version. A pointer (asterisk - *) shows which version is currently the primary one. To set a different primary version, select option 4 from the Setup Main Menu. A menu similar to the following displays: Primary Version Screen M S/W Version: Slot #: 1 <CR> Refresh the screen 0. Return to Previous Menu 1. Save the Session Select the Primary version (The current primary is marked by *) 2. Version * Version >>>Enter your choice: Set Primary Version Once you select and save the desired primary version, you are prompted to reboot the M Type Y and the M will set the pointer accordingly, and reboot from the newly-defined primary version. If you don't wish to reboot at this time, the pointer is saved, but the M continues running from the old version. 18 M2-1000SX/LX Installation Guide

21 Chapter 4 Troubleshooting Use the table below to troubleshoot common problems. If you still experience problems, please contact Avaya Technical Support. Problem Probable Cause Solution OPR LED blinking continuously Port LED blinking while function LED is on LNK 10/100 speed DIP switch has no effect Autonegotiation problem on 10/100M port Module failed to join the DomainX due to overflow of Domain Resource Units (DRUs) Link failure USW DIP switch is off Remote is set to Autonegotiation enable Reconfigure the hub to reduce the DRU load on the DomainX. Do not exceed the maximum of 100 DRUs per DomainX. Refer to section Domain Usage Considerations. Verify that the cable connector is properly inserted into the port. Check the cable integrity, and replace the cable if necessary. Ensure that you Do not use autonegotiation for the Gigabit ports. Do not connect M2-1000SX to M2-1000LX modules. You may be using a cable with too low a modal bandwidth or too high a range ( m for the M2-1000SX; 5 km on 10 µm cable for the M2-1000LX. Switch USW DIP switch M2-1000SX/LX Installation Guide 19

22 Chapter 4 Troubleshooting Software Download Troubleshooting The following are Activity Status messages that can appear during software download, their meanings, and suggested solutions. Activity Status message Description Suggested action File format unknown Ensure that the correct agent software file is being downloaded to the agent File not found Failure of TFTP Get Type in the correct path and filename Server is unreachable Failed to find the server after 1 minute Type in the correct TFTP Server IP address. Ensure the server is accessible to the agent by typing ping <ip_address_of_agent>. Alternatively, if a router is required to reach the server, type in the router address from the IP Routes menu, as explained in the IP Routes section. 20 M2-1000SX/LX Installation Guide

23 Appendix Connector Pin Assignments The following table shows the connector pin assignments of the 10BASE-T/100BASE-TX shielded RJ45 port connector. Table 6 10BASE-T/100BASE-TX Shielded RJ45 Port Pin# Link Signal 1 Rx+ 2 Rx- 3 Tx Tx- Connector body Shield (STP) M2-1000SX/LX Installation Guide 21

24 avaya.com CajunView is a trademark, and in some jurisdictions may be a registered trademark of Avaya Inc. or its affiliated companies. Other trademarks appearing in this document are the property of their respective owners. Copyright 2001, Avaya Inc. All rights reserved.