First Choice Internet

Transcription

1 TheGreenBow IPSec VPN Client Configuration Guide Omron MR504DV WebSite: Contact: Configuration Guide written by: Writer: Company: Bernd Plagge First Choice Internet IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

2 Table of contents 1 Introduction Goal of this document VPN Network topology OMRON MR504DV Availability OMRON MR504DV VPN Gateway product info Omron MR540DV VPN configuration TheGreenBow IPSec VPN Client configuration VPN Client Phase 1 (IKE) Configuration VPN Client Phase 2 (IPSec) Configuration Open IPSec VPN tunnels Tools in case of trouble A good network analyser: Wireshark VPN IPSec Troubleshooting «PAYLOAD MALFORMED» error (wrong Phase 1 [SA]) «INVALID COOKIE» error «no keystate» error «received remote ID other than expected» error «NO PROPOSAL CHOSEN» error «INVALID ID INFORMATION» error I clicked on Open tunnel, but nothing happens The VPN tunnel is up but I can t ping! Contacts IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

3 1 Introduction 1.1 Goal of this document This configuration guide describes how to configure TheGreenBow IPSec VPN Client with a Omron MR504DV VPN router. 1.2 VPN Network topology In our VPN network example (diagram hereafter), we will connect TheGreenBow IPSec VPN Client to the LAN behind the Omron MR504DV router. The VPN client is connected to the Internet with an optical fibre connection or through a LAN. All the addresses in this document are given for example purpose. IPSec VPN Client ( ) Internet Omron MR540DV Any IP number IPSec VPN Client (as seen on the LAN) 1.3 OMRON MR504DV Availability This router is currently sold in Japan and thus it has a Japanese interface. 1.4 OMRON MR504DV VPN Gateway product info The Omron router is shipped with a manual CD containing the manual in PDF form. In addtion the Omrom website contains configuration examples. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

4 2 Omron MR540DV VPN configuration Ensure that you can connect to the Omron MR540DV router (ping) and then start the browser and point it to the Omron MR540DV routers IP address. Login (default user is: admin) and process to detailed configuration. Then proceed to VPN (IPSec) 設定 Don't forget to enable IPSec; you need to check the 使用する field! IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

5 As this configuration is for a Road Warrior who may connect from any place the gateway doesn't have a fixed IP address. We check the moving ( 動的 ) field. At the top we enter the IP range for the VPN client (here start address and netmask). In the second block we use confirmation protocol (ESP), the corresponding algorithm and the encryption algorithm and protocol. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

6 In the third block we select IKE (Internet Key Exchange) and we specify that we want to use a preshared key. This is considerably simpler than using certificates. We also enter the hash algorithm, encryption algorithm and main mode to be used. Check IKE Keep Alive and enter the remote IP address. Enter other parameters as shown above to use your values. The router also supports certificates. Certificates can be generated or imported. The configuration file can be exported and when necessary re-imported again. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

7 3 TheGreenBow IPSec VPN Client configuration This section describes the required configuration to connect to a Omron MR504DV VPN router. To download the latest release of TheGreenBow IPSec VPN Client software, please go to VPN Client Phase 1 (IKE) Configuration Phase 1 configuration You may use either Preshared, Certificates, USB Tokens or X-Auth for User Authentication with the Omron MR504DV router. This configuration is one example of what can be accomplished in term of User Authentication. You may want to refer to either the Omron MR504DV router user guide or TheGreenBow IPSec VPN Client User Guide for more details on User Authentication options. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

8 3.2 VPN Client Phase 2 (IPSec) Configuration You may define a static virtual IP address here. If you use , you will have error Local-ID is missing. It does not prevent you from establishing a tunnel Enter the IP address (and subnet mask) of the remote LAN. Phase 2 Configuration Phase 2 Advanced 3.3 Open IPSec VPN tunnels Once both Omron MR504DV router and TheGreenBow IPSec VPN Client software have been configured accordingly, you are ready to open VPN tunnels. First make sure you enable your firewall with IPSec traffic. 1. Click on "Save & Apply" to take into account all modifications we've made on your VPN Client configuration IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

9 2. Click on "Open Tunnel", or generate traffic that will automatically open a secure IPSec VPN Tunnel (e.g. ping, IE browser) 3. Select "Connections" to see opened VPN Tunnels 4. Select "Console" if you want to access to the IPSec VPN logs and adjust filters to display less IPSec messaging. The following example shows a successful connection between TheGreenBow IPSec VPN Client and a Omron MR504 DV VPN router. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

10 4 Tools in case of trouble Configuring an IPSec VPN tunnel can be a hard task. One missing parameter can prevent a VPN connection from being established. Some tools are available to find source of troubles during a VPN establishment. 4.1 A good network analyser: Wireshark Wireshark is a free software that can be used for packet and traffic analysis. It shows IP or TCP packets received on a network card. This tool is available on website It can be used to follow protocol exchange between two devices. For installation and use details, read its specific documentation ( IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

11 5 VPN IPSec Troubleshooting 5.1 «PAYLOAD MALFORMED» error (wrong Phase 1 [SA]) Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [NOTIFY] Default exchange_run: exchange_validate failed Default dropped message from port 500 due to notification type PAYLOAD_MALFORMED Default SEND Informational [NOTIFY] with PAYLOAD_MALFORMED error If you have an «PAYLOAD MALFORMED» error you might have a wrong Phase 1 [SA], check if the encryption algorithms are the same on each side of the VPN tunnel. 5.2 «INVALID COOKIE» error Default message_recv: invalid cookie(s) 5918ca0c f 7364e3e486e Default dropped message from port 500 due to notification type INVALID_COOKIE Default SEND Informational [NOTIFY] with INVALID_COOKIE error If you have an «INVALID COOKIE» error, it means that one of the endpoint is using a SA that is no more in use. Reset the VPN connection on each side. 5.3 «no keystate» error Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [ID][HASH][NOTIFY] Default ipsec_get_keystate: no keystate in ISAKMP SA 00B57C50 Check if the preshared key is correct or if the local ID is correct (see «Advanced» button). You should have more information in the remote endpoint logs. 5.4 «received remote ID other than expected» error Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [ID][HASH][NOTIFY] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [ID][HASH][NOTIFY] Default ike_phase_1_recv_id: received remote ID other than expected support@thegreenbow.fr The «Remote ID» value (see «Advanced» Button) does not match what the remote endpoint is expected. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

12 5.5 «NO PROPOSAL CHOSEN» error Doc.Ref tgbvpn_cg_omron_mr Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [ID][HASH][NOTIFY] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [ID][HASH][NOTIFY] Default phase 1 done: initiator id c364cd70: , responder id c364cd72: , src: dst: Default (SA CNXVPN1-CNXVPN1-P2) SEND phase 2 Quick Mode [SA][KEY][ID][HASH][NONCE] Default RECV Informational [HASH][NOTIFY] with NO_PROPOSAL_CHOSEN error Default RECV Informational [HASH][DEL] Default CNXVPN1-P1 deleted If you have an «NO PROPOSAL CHOSEN» error, check that the «Phase 2» encryption algorithms are the same on each side of the VPN Tunnel. Check «Phase 1» algorithms if you have this: Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default RECV Informational [NOTIFY] with NO_PROPOSAL_CHOSEN error 5.6 «INVALID ID INFORMATION» error Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [SA][VID] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [KEY][NONCE] Default (SA CNXVPN1-P1) SEND phase 1 Main Mode [ID][HASH][NOTIFY] Default (SA CNXVPN1-P1) RECV phase 1 Main Mode [ID][HASH][NOTIFY] Default phase 1 done: initiator id c364cd70: , responder id c364cd72: , src: dst: Default (SA CNXVPN1-CNXVPN1-P2) SEND phase 2 Quick Mode [SA][KEY][ID][HASH][NONCE] Default RECV Informational [HASH][NOTIFY] with INVALID_ID_INFORMATION error Default RECV Informational [HASH][DEL] Default CNXVPN1-P1 deleted If you have an «INVALID ID INFORMATION» error, check if «Phase 2» ID (local address and network address) is correct and match what is expected by the remote endpoint. Check also ID type ( Subnet address and Single address ). If network mask is not check, you are using a IPV4_ADDR type (and not a IPV4_SUBNET type). 5.7 I clicked on Open tunnel, but nothing happens. Read logs of each VPN tunnel endpoint. IKE requests can be dropped by firewalls. An IPSec Client uses UDP port 500 and protocol ESP (protocol 50). 5.8 The VPN tunnel is up but I can t ping! If the VPN tunnel is up, but you still cannot ping the remote LAN, here are a few guidelines: Check Phase 2 settings: VPN Client address and Remote LAN address. Usually, VPN Client IP address should not belong to the remote LAN subnet Once VPN tunnel is up, packets are sent with ESP protocol. This protocol can be blocked by firewall. Check that every device between the client and the VPN server does accept ESP Check your VPN server logs. Packets can be dropped by one of its firewall rules. Check your ISP support ESP IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

13 If you still cannot ping, follow ICMP traffic on VPN server LAN interface and on LAN computer interface (with Wireshark for example). You will have an indication that encryption works. Check the default gateway value in VPN Server LAN. A target on your remote LAN can receive pings but does not answer because there is a no Default gateway setting. You cannot access to the computers in the LAN by their name. You must specify their IP address inside the LAN. We recommend you to install Wireshark ( on one of your target computer. You can check that your pings arrive inside the LAN. IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14

14 6 Contacts News and updates on TheGreenBow web site: Technical support by at Sales contacts by at IPSec VPN Router Configuration Property of TheGreenBow Sistech SA - Sistech /14