Powerful WLAN controller for the central management of 25 to 100 access points and WLAN routers

Transcription

1 Wireless LAN LANCOM WLC Powerful WLAN controller for the central management of 25 to 100 access points and WLAN routers The LANCOM WLC is a powerful WLAN controller with central WLAN management for installations with up to 100 access points. The distribution of firmware updates and configurations takes place via only one device - a massive assistance and time saver for every administrator. a Central firmware rollout, monitoring & management of 25 to 100 access points and WLAN routers a Zero-touch deployment of connected WLAN devices a Optimized raoming behavior of WLAN clients via IEEE r and OKC a Comprehensive VLAN-, RADIUS-, and IEEE 802.1X/EAP functions a Highest operational reliability without "single-point-of-failure" a Dynamic WLAN optimization thanks to LANCOM Active Radio Control (ARC) a High availability of WLAN infrastructures with High Availability Clustering Option

2 LANCOM WLC Central firmware rollout, monitoring & management With the LANCOM WLC up to 100 access points and WLAN routers can be configured and managed automatically and centrally - a massive assistance and time saver for the administrator. This way the WLAN controller offers a consistent network control, security, and reliability. Zero-touch deployment Quick and easy network integration of new access points as well as automatic configuration rollout without the need of manual configuration. After network authentication, the LANCOM WLC immediately sends an appropriate configuration to the WLAN device. Optimized roaming behavior of WLAN clients LANCOM WLAN controllers assure the communication between the administrated access points and WLAN routers. This way, clients can be passed from one WLAN device to another crossing two radio fields without any connection losses. VLAN-, RADIUS-, and IEEE 802.1X/EAP functions Thanks to extensive virtualization and security functions, wireless networks can be set up efficiently and compliant to the proprietary security policies. The integrated VLAN functionality enables the separation of several wireless networks in only one infrastructure. Furthermore, there are professional security functions which allow the administrator to grant network access only to authorized clients. Highest operational security The LANCOM Smart Controller principle assures highest operational security: While administration data is transferred via the controller, traffic data is sent directly from the client to the access point and therefrom directly to the router. If one controller breaks down, the access point switches to stand-alone mode in order to maintain the communication between client and access point. This way, there are no unproductive hours due to employees not getting Internet access or the failure of WLAN-based machines. Active Radio Control for dynamic radio-field optimization The LANCOM WLC supports the WLAN optimization concept LANCOM Active Radio Control. This intelligent combination of innovative features included with the LCOS operating system such as Band Steering, Adaptive Noise Immunity, RF Optimization, and Client Steering sustainably increases WLAN performance and supports administrators with professional tools for WLAN management. High availability In combination with the LANCOM High Availibility Clustering Option several WLAN controllers are grouped to a high-availability cluster. As a consequence, configuration changes, functions, and extensions which are set up at one WLC can be automatically transferred to the other WLCs without managing every single device manually - an enormous time saver for administrators. Maximum future viability LANCOM products are designed for a service life of several years and are equipped with hardware dimensioned for the future. Even reaching back to older product generations, updates to the LANCOM Operating System LCOS are available several times a year, free of charge and offering major features.

3 WLAN profile settings* Radio channels 5 GHz Radio channels 2.4 GHz Concurrent WLAN clients IEEE u Roaming Opportunistic Key Caching Fast roaming Security Quality of Service Background scanning Client detection Auto WDS* Space Time Block Coding (STBC)* Low Density Parity Check (LDPC)* *) Note Security Encryption options Encryption EAP types (authenticator) RADIUS/EAP-server Others Others LANCOM Active Radio Control Client Steering* Band Steering Managed RF Optimization* Adaptive Noise Immunity Spectral Scan Up to 26 non-overlapping channels (available channels and further obligations such as automatic DFS dynamic channel selection depending on national regulations) Up to 13 channels, max. 3 non-overlapping (depending on country-specific restrictions) Depends on the access points in operation Managed LANCOM Access Points support the WLAN standard IEEE u (Hotspot 2.0) which allows mobile clients a seamless transition from the cellular network into WLAN hotspots. Authentication methods using SIM card information, certificates or username and password, enable an automatic, encrypted login to WLAN hotspots of roaming partners - without the need to manually enter login credentials Seamless handover between radio cells, IAPP support with optional restriction to an ARF context, IEEE d support Opportunistic key caching allows fast roaming processes between access points. WLAN installations utilizing a WLAN controller and IEEE 802.1X authentication cache the access keys of the clients and are transmitted by the WLAN controller to all mananged access points Based on IEEE r, allows fast roaming procedures between access points. This is possible by using IEEE 802.1X authentication or pre-shared keys in controller based WLAN installations, which save the access keys temporarily and distribute them to the managed access points. IEEE i / WPA2 with passphrase (WPA2-Personal) or IEEE 802.1X (WPA2-Enterprise) and hardware-accelerated AES, closed network, WEP64, WEP128, WEP152, user authentication, IEEE 802.1x /EAP, LEPS, WPA1/TKIP Prioritization according to Wireless Multimedia Extensions (WME, subset of IEEE e) Detection of rogue AP's and the channel information for all WLAN channels during normal AP operation. The Background Scan Time Interval defines the time slots in which an AP or Router searches for a foreign WLAN network in its vicinity. The time interval can be specified in either milliseconds, seconds, minutes, hours or days Rogue WLAN client detection based on probe requests Auto WDS allows wireless integration of access points in existing WLAN infrastructure, including managment via WLAN controller. Coding method according to IEEE n. The Space Time Block Coding improves reception by coding the data stream in blocks. Low Density Parity Check (LDPC) is an error correcting method. IEEE n uses convolution coding (CC) as standard error correcting method, the usage of the more effective Low Density Parity Check (LDPC) is optional. Depends on the access points in operation IEEE 802.1X (WPA2-Enterprise), IEEE i (WPA2-Personal), Wi-Fi Certified WPA2, WPA, WEP, IEEE w (Protected Management Frames), LEPS (LANCOM Enhanced Passphrase Security) AES:CCMP (Advanced Encryption Standard with Counter Mode and Cipher Block Chaining Message Authentication Code Protocol), TKIP (Temporal Key Integrity Protocol), RC4 (only used by WEP) EAP-TLS, EAP-TTLS/MSCHAPv2, PEAPv0/EAP-MSCHAPv2, PEAPv1/EAP-GTC, EAP-FAST User administration MAC-based, rate limiting, passphrases, VLAN user based, authentication of IEEE 802.1X clients via EAP-TLS, EAP-TTLS, EAP-MD5, EAP-GTC, PEAP, MSCHAP or MSCHAPv2 WLAN protocol filters, IP-redirection of any packet received over the WLAN interface, IEEE 802.1X supplicant, background scanning, client detection ("rogue WLAN client detection"), Wireless Intrusion Detection System (WIDS) IEEE 802.1X supplicant, background scanning, client detection ("rogue WLAN client detection"), Wireless Intrusion Detection System (WIDS) Steering of WLAN clients to the ideal access point Steering of 5GHz clients to the corresponding high-performance frequency band Selection of optimal WLAN channels by the administrator Better WLAN throughput due to immunity against interferences Monitoring your WLAN for sources of interference

4 LANCOM Active Radio Control Adaptive RF Optimization Airtime Fairness *) Note WLAN-Controller Number of managed devices Smart Controller technology Auto Discovery Authentication and Authorization Management communication protocol Layer-3 Tunneling Encryption Firmware deployment Script distribution RF management and automatic RF optimization Configuration management Inheritance of configuration profiles Management operating modes Stand alone operation VLAN and IP contexts Dynamic VLAN assignment Dynamic selection of the optimal WLAN channel Improved utilization of the WLAN bandwidth Depends on the access points in operation. Steering of WLAN clients is not available in US version Up to 25 LANCOM Access Points and WLAN routers can be centrally managed by the WLAN controller. The WLC expansion options extends support upto 100 LANCOM Access Points and WLAN routers to be managed. Capacities can be expanded even further by cascading multiple Controllers. The WLAN controller can switch user data per AP Radio or per SSID in the following ways: Direct switching to the LAN at the AP (for maximum performance, e.g. for IEEE n-based access points) Logical seperation of user data into VLAN's (e.g. for WLAN guest access accounts) Central tunneling to the Controller* (layer 3 tunneling between different IP Subnets) *from LCOS 8.5x LANCOM access points and WLAN routers automatically discover the WLAN controller by means of DNS name or IP addresses. Even AP's at remote sites or in home offices with no direct access to the Controller can be integrated into the central Controller Access Points can be authenticated manually or automatically. Signaling of new access points by LED, message, SYSLOG and SNMP traps. Manual authentication via LANmonitor or WEBconfig GUI tools. Semi-automatic authentication based on access-point lists in the Controller ('bulk mode'). Fully automatic authentication with default configuration assignement (can be activated/deactivated separately, e.g. during the rollout phase). Authenticated access points can be identified by means of digital certificates; certificate generation by integrated CA (Certificate Authority); certificate distribution by SCEP (Simple Certificate Enrollment Protocol). Access points can be blocked by CRL (Certificate Revocation List). CAPWAP (Control and Provisioning Protocol for Wireless Access Points) Layer-3 Tunneling in conformity with the CAPWAP standard allows the bridging of WLANs per SSID to a separate IP subnet. Layer-2 packets are encapsulated in Layer-3 tunnels and transported to a LANCOM WLAN controller. By doing this the access point is independent of the present infrastructure of the network. Possible applications are roaming without changing the IP address and compounding SSIDs without using VLANs DTLS encryption of the control channel between WLAN controller and Access Point (256-bit AES encryption with digital certificates, incl. hardware encryption accelerator; encryption can be disabled for diagnostic purposes). Central Firmware deployment and management of the Access Points. Requires an external web server. Automatic Firmware update on the Access Points is also possible. The Controller checks every day, depending on the defined policy, for the latest Firmware and compares it with the versions in the devices. This can also be activated using Cron jobs. If there is a Firmware mismatch, then the Controller downloads the matching Firmware from the server and updates the corresponding Access Points and Routers. Enables the complete configuration of non-wlan specific functions such as Redirects, Protocol Filter, ARF etc. Internal storage of up to three script files (max. 64 kbyte) for provisioning access points without a separate HTTP server The channel deployment can be static or can be automated. Upon activation of the RF Optimization setting, the Access Points search for an optimal channel in the 2.4 GHz band. The selected channels are sent to the Controller saves these channels on the corresponding Access Points. RF Optmization can also be activated for individual Access Points. Transmit power setting static between 0 to -20 db. Alarm notification in case of Access Point failure by LED, , SYSLOG and SNMP traps. Definition and grouping of all logical and physical WLAN parameters by means of WLAN configuration profiles. Fully automatic or manual profile assignment to WLAN Access Points; automatic transfer and configuration verification (policy enforcement). Support of hierarchical WLAN profile groups. New profiles can be easily created by inheriting parameters from existing profiles. The AP can be set to 'managed' or 'unmanaged' mode for each radio interface. With LANCOM WLAN routers, the Controller manages the WLAN part only (split management). In 'Managed' mode, an adjustable setting defines the time-span for which the AP continues Stand-alone operation in the event the connection to the Controller fails. After this time-span the AP configuration is deleted and the AP resumes operation only after the connection to the Controller is reestablished. By default this value is set to zero and AP ceases operation as soon as connection to the Controller is lost. Alternatively, a special time setting allows the AP to function in Stand-alone mode indefinetly. In Stand-alone mode only Pre-shared Key SSID's are functional. A fixed VLAN can be set for each SSID. The WLAN controller can independently provide up to 16 separate IP networks, and each of these can be individually mapped to VLANs and, consequently, to SSIDs (Advanced Routing and Forwarding, ARF). The Controller can provide, among others, individual DHCP, DNS, routing, firewall and VPN functions for these networks. Dynamic VLAN assignment for target user groups based on MAC addresses, BSSID or SSID by means of external RADIUS server.

5 WLAN-Controller RADIUS server EAP server RADIUS/EAP proxy per SSID Redundancy, Controller backup and load balancing LED control CA hierarchy Load balancing Backup Fast roaming QoS Background scanning, rogue-ap and rogue-client detection WLAN visualization WLAN guess access accounts Public Spot function WLAN client limiting Automatic configuration alignment (Config Sync)* Management software Integrated RADIUS server for MAC address list management. Support for RADSEC (Secure RADIUS) for secure communication with RADIUS servers. Integrated EAP server for authentication of IEEE 802.1X clients via EAP-TLS, EAP-TTLS, EAP-MD5, EAP-GTC, PEAP, MSCHAP or MSCHAPv2 Proxy mode for external RADIUS/EAP servers (forwarding and realm handling) per SSID Every managed LANCOM AP can be assigned to a group of alternative WLAN controllers. A suitable Controller is selected within this group depending on AP load. This ensures that also in backup state the load of larger installations remains equally distributed. The LEDs of administrated WLAN devices can be centrally deactivated via the WLAN controller The Certificate Authority (CA) can be structured hierarchically when using multiple WLAN controllers. This allows access points to swap between different WLAN controllers without certificate conflicts. The Certificate Revocation Lists (CRL) can be shared between the different devices When using multiple WLAN controllers the access points are distributed evenly among the different WLAN controllers to offer the best load balancing. In case one WLAN controller is unavailable the access points are edistributed among the remaining WLAN controllers automatically. Once it is restored they are redistributed again. A priority can be set for the WLAN Controller which allows operating in hot standby mode. Access points switch automatically to the WLAN controller with the highest priority VoWLAN devices require seamless roaming for ensuring optimal speech quality. The Access Points support PMK caching and Pre-authentication for such demanding applications. WPA2 and WPA2-PSK operate with sub-85 ms roaming times (requirements: adequate signal quality, sufficient RF overlap, clients with a low roaming threshold). IEEE e / WME: Automatic VLAN tagging (IEEE 802.1p) in the Access Points. Mapping to DiffServ attributes in the WLAN controller if this is deployed as a layer-3 router Background scanning does not interupt normal AP operation and collects information on the radio channel load (AP acts as a 'Probe' or 'Sensor' by going off-channel). Foreign Access Points and clients is sent to the Rogue AP Detection in LANCOM WLANmonitor. The management tool LANCOM WLANmonitor (included) acts as a central monitoring program for the WLAN controller and visualizes the performance of all WLAN controllers, Access Points, SSIDs and clients. Static mapping of guest SSIDs in VLANs, access limitations and VLAN routing by means of ARF (Advanced Routing and Forwarding). Optional functionality (see at available options). Easy set-up of guest accounts with just a few mouse clicks using the Voucher-Wizard. The vouchers can be printed over any standard Printer on the network. The Voucher-Wizard can be customized by uploading an individual logo. Function works without external RADIUS and Accounting Servers. Configuration of time and/or traffic budgets as well as when accounting should start. Support of public certificates and certificate chains from trust centers for Public Spots. This allows popular browsers to access trustworthy login pages with secure access (HTTPS) without warnings To ensure that load is evenly balanced between multiple Access Points, each one can be set with a maximum number of allowable WLAN clients. Due to the grouping of several individual devices to one device group (cluster), configuration changes conducted for one device can be automatically synchronized with all cluster devices, without having to manage each device manually (Config Sync). Included: - LANCOM LANconfig - LANCOM LANmonitor - LANCOM WLANmonitor *) Supported Access Points and WLAN routers Only with WLC Clustering XL Option Indoor 1 LANCOM L-151gn Wireless, LANCOM L-151E Wireless, LANCOM L-54g Wireless, LANCOM L-54ag Wireless, LANCOM L-54 dual Wireless 1 LANCOM L-305agn Wireless, LANCOM L-310agn Wireless, LANCOM L-315agn dual Wireless 1 LANCOM L-320agn Wireless, LANCOM L-320agn Wireless (white), LANCOM L-321agn Wireless, LANCOM L-322agn dual Wireless, LANCOM L-322E Wireless, LANCOM L-330agn dual Wireless 1 LANCOM L-451agn Wireless, LANCOM L-452agn dual Wireless, LANCOM L-460agn dual Wireless 1 LANCOM LN-830acn dual Wireless, LANCOM LN-830E Wireless, LANCOM L-822acn dual Wireless, LANCOM L-1302acn dual Wireless, LANCOM L-1310acn dual Wireless, LANCOM LN-860, LANCOM LN LANCOM LN-1700, LANCOM LN-1702

6 Supported Access Points and WLAN routers Outdoor 1 LANCOM OAP-54 Wireless, LANCOM OAP-54-1 Wireless 1 LANCOM OAP-310 Wireless 1 LANCOM OAP-321, LANCOM OAP-321-3G 1 LANCOM OAP-382, LANCOM OAP LANCOM OAP-821, LANCOM OAP-822, LANCOM OAP-830 Industrial 1 LANCOM IAP-54 Wireless 1 LANCOM XAP-40-2 Wireless 1 LANCOM IAP-321, LANCOM IAP-321-3G, LANCOM IAP LANCOM IAP-821, LANCOM IAP-822 UMTS/HSPDA 1 LANCOM 1780EW-4G, LANCOM 1780EW-3G, LANCOM 1780EW-4G+ 1 LANCOM 3850 Wireless WLAN-Router and IADs 1 LANCOM 1781VAW, LANCOM 1781AW, LANCOM 1781EW(+) 1 LANCOM 1811n Wireless, LANCOM 1821n Wireless, LANCOM 1823 VoIP, LANCOM Wireless ADSL Functions in layer-3 routing mode Note: Layer 2 features VLAN Quality of Service Rate limiting Multicast Protocols Layer 3 features Firewall Quality of Service Security PPP authentication mechanisms High availability / redundancy Router Router virtualization IPv4 services IPv6 services IPv6 compatible LCOS applications Dynamic routing protocols Some of the below functions are only active when the device is operating as a router, firewall or VPN gateway IDs based on IEEE 802.1q, dynamic assignment, Q-in-Q tagging WME based on IEEE e, Wi-Fi Certified WMM SSID based, WLAN client based IGMP-Snooping Ethernet over GRE-Tunnel (EoGRE), ARP-Lookup, LLDP, DHCP option 82, IPv6-Router-Advertisement-Snooping, DHCPv6-Snooping, LDRA (Lightweight DHCPv6 Relay Agent), Spanning Tree, Rapid Spanning Tree, ARP, Proxy ARP, BOOTP, DHCP, LACP Stateful inspection firewall including paket filtering, extended port forwarding, N:N IP address mapping, paket tagging, user-defined rules and notifications Traffic shaping, bandwidth reservation, DiffServ/TOS, packetsize control, layer-2-in-layer-3 tagging Intrusion Prevention, IP spoofing, access control lists, Denial of Service protection, detailed settings for handling reassembly, session-recovery, PING, stealth mode and AUTH port, URL blocker, password protection, programmable reset button PAP, CHAP, MS-CHAP, and MS-CHAPv2 VRRP (Virtual Router Redundancy Protocol), analog/gsm modem backup IPv4-, IPv6-, NetBIOS/IP multiprotokoll router, IPv4/IPv6 dual stack ARF (Advanced Routing and Forwarding) up to separate processing of 16 contexts HTTP and HTTPS server for configuration by web interface, DNS client, DNS server, DNS relay, DNS proxy, dynamic DNS client, DHCP client, DHCP relay and DHCP server including autodetection, NetBIOS/IP proxy, NTP client, SNTP server, policy-based routing, Bonjour-Proxy, RADIUS HTTP and HTTPS server for configuration by web interface, DHCPv6 client, DHCPv6 server, DHCPv6 relay, DNS client, DNS server, dynamic DNS client, NTP client, SNTP server, Bonjour-Proxy, RADIUS WEBconfig, HTTP, HTTPS, SSH, Telnet, DNS, TFTP, firewall, RAS dial-in RIPv2, BGPv4, OSPFv2

7 Layer 3 features IPv4 protocols IPv6 protocols WAN operating mode WAN protocols Tunneling protocols (IPv4/IPv6) VPN IPSec over HTTPS Number of VPN tunnels Hardware accelerator Realtime clock Random number generator 1-Click-VPN Site-to-Site IKE, IKEv2 Smart Certificate Certificates Certificate rollout Certificate revocation lists (CRL) OCSP Client XAUTH Proadaptive VPN Algorithms NAT-Traversal IPCOMP Dynamic DNS Specific DNS forwarding IPv4 VPN IPv4 VPN over IPv6 WAN IPv6 VPN IPv6 VPN over IPv4 WAN Radius DNS, HTTP, HTTPS, ICMP, NTP/SNTP, NetBIOS, PPPoE (server), RADIUS, RADSEC (secure RADIUS), RTP, SNMPv1,v2c,v3, TFTP, TACACS+ NDP, stateless address autoconfiguration (SLAAC), stateful address autoconfiguration (DHCPv6), router advertisements, ICMPv6, DHCPv6, DNS, HTTP, HTTPS, PPPoE, RADIUS, SMTP, NTP, BGP, Syslog, SNMPv1,v2c,v3 VDSL, ADSL1, ADSL2 or ADSL2+ additional with external DSL modem at an ETH port PPPoE, Multi-PPPoE, ML-PPP, GRE, EoGRE, PPTP (PAC or PNS), L2TPv2 (LAC or LNS) and IPoE (using DHCP or no DHCP), RIP-1, RIP-2, VLAN, IPv6 over PPP (IPv6 and IPv4/IPv6 dual stack session), IP(v6)oE (autokonfiguration, DHCPv6 or static) 6to4, 6in4, 6rd (static and over DHCP), Dual Stack Lite (IPv4-in-IPv6-Tunnel) Enables IPsec VPN based on TCP (at port 443 like HTTPS) which can go through firewalls in networks where e. g. port 500 for IKE is blocked. Suitable for client-to-site connections and site-to-site connections. IPSec over HTTPS is based on the NCP VPN Path Finder technology Max. number of concurrent active IPSec, PPTP (MPPE) and L2TPv2 tunnels: 5. Unlimited configurable connections. Integrated hardware accelerator for 3DES/AES encryption and decryption Integrated, buffered realtime clock to save the date and time during power failure. Assures timely validation of certificates in any case Generates real random numbers in hardware, e. g. for improved key generation for certificates immediately after switching-on Creation of VPN connections between LANCOM routers via drag and drop in LANconfig IPSec key exchange with Preshared Key or certificate (RSA signature, digital signature) Convenient generation of digital X.509 certificates via an own certifaction authority (SCEP-CA) on the webpage or via SCEP. X.509 digital multi-level certificate support, compatible with Microsoft Server / Enterprise Server and OpenSSL. Secure Key Storage protects a private key (PKCS#12) from theft. Automatic creation, rollout and renewal of certificates via SCEP (Simple Certificate Enrollment Protocol) per certificate hierarchy CRL retrieval via HTTP per certificate hierarchy Check X.509 certifications by using OCSP (Online Certificate Status Protocol) in real time as an alternative to CRLs XAUTH client for registering LANCOM routers and access points at XAUTH servers incl. IKE-config mode. XAUTH server enables clients to register via XAUTH at LANCOM routers. Connection of the XAUTH server to RADIUS servers provides the central authentication of VPN-access with user name and password. Authentication of VPN-client access via XAUTH and RADIUS connection additionally by OTP token Automated configuration and dynamic creation of all necessary VPN and routing entries based on a default entry for site-to-site connections. Propagation of dynamically learned routes via RIPv2 if required 3DES (168 bit), AES (128, 192 or 256 bit), Blowfish (128 bit), RSA ( bit) and CAST (128 bit). OpenSSL implementation with FIPS-140 certified algorithms. MD-5, SHA-1 or SHA-256 hashes NAT-Traversal (NAT-T) support for VPN over routes without VPN passthrough VPN data compression based on Deflate compression for higher IPSec throughput on low-bandwidth connections (must be supported by remote endpoint) Enables the registration of IP addresses with a Dynamic DNS provider in the case that fixed IP addresses are not used for the VPN connection DNS forwarding according to DNS domain, e.g. internal names are translated by proprietary DNS servers in the VPN. External names are translated by Internet DNS servers Connecting private IPv4 networks Use of IPv4 VPN over IPv6 WAN connections Connecting private IPv6 networks Use of IPv6 VPN over IPv4 WAN connections RADIUS authorization and accounting, outsourcing of VPN configurations in external RADIUS server in IKEv2, RADIUS CoA (Change of Authorization)

8 VPN throughput (max., AES) 1416-byte frame size UDP Firewall throughput (max.) 1518-byte frame size UDP Content Filter (optional) Demo version URL filter database/rating server* URL check* Categories/category profiles* Override** Black-/whitelist Profiles Time frames Flexible firewall action Individual display pages (for blocked, error, override) Redirection to external pages License management Statistics Notifications Wizard for typical configurations Max. users *) Note **) Note VoIP SIP ALG 337 Mbps 643 Mbps Activate the 30-day trial version after free registration under Worldwide, redundant rating servers from IBM Security Solutions for querying URL classifications. Database with over 100 million entries covering about 10 billion web pages. Web crawlers automatically search and classify web sites to provide nearly 150,000 updates per day: They use text classification by optical character recognition, key word searches, classification by word frequency and combinations, web-site comparison of text, images and page elements, object recognition of special characters, symbols, trademarks and prohibited images, recognition of pornography and nudity by analyzing the concentration of skin tones in images, by structure and link analysis, by malware detection in binary files and installation packages Database based online check of web sites (HTTP/HTTPS). HTTPS websites are checked based on DNS names of HTTPS server certificates or based on Reverse DNS lookup of IP addresses. Filter rules can be defined in each profile by collecting category profiles from 58 categories, for example to restrict Internet access to business purposes only (limiting private use) or by providing protection from content that is harmful to minors or hazardous content (e.g. malware sites). Clearly structured selection due to the grouping of similar categories. Content for each category can be allowed, blocked, or released by override Each category can be given an optional manual override that allows the user to access blocked content on a case-by-case basis. The override operates for a limited time period by allowing the category or domain, or a combination of both. Optional notification of the administrator in case of overrides Lists that are manually configured to explicitly allow (whitelist) or block (blacklist) web sites for each profile, independent of the rating server. Wildcards can be used when defining groups of pages or for filtering sub pages Timeframes, blacklists, whitelists and categories are collected into profiles that can be activated separately for content-filter actions. A default profile with standard settings blocks racist, pornographic, criminal, and extremist content as well as anonymous proxies, weapons/military, drugs, SPAM and malware Timeframes can be flexibly defined for control over filtering depending on the time of day or weekday, e.g. to relax controls during break times for private surfing Activation of the content filter by selecting the required firewall profile that contains content-filter actions. Firewall rules enable the flexible use of your own profiles for different clients, networks or connections to certain servers Response pages displayed by the content filter in case of blocked sites, errors or overrides can be custom designed. Variables enable the inclusion of current information such as the category, URL, and rating-server categorization. Response pages can be issued in any language depending on the language set in the user's web browser As an alternative to displaying the device's own internal response pages to blockings, errors or overrides, you can redirect to external web servers Automatic notification of license expiry by , LANmonitor, SYSLOG or SNMP trap. Activation of license renewal at any time before expiry of the current license (the new licensing period starts immediately after expiry of the current license) Display of the number of checked and blocked web pages by category in LANmonitor. Logging of all content-filter events in LANmonitor; log file created daily, weekly or monthly. Hit list of the most frequently called pages and rating results. Analysis of the connection properties; minimum, maximum and average rating-server response time Messaging in case of content-filter events optionally by , SNMP, SYSLOG or LANmonitor Wizard sets up the content filters for a range of typical scenarios in a few simple steps, including the creation of the necessary firewall rules with the corresponding action Simultaneous checking of HTTP(S) traffic for a maximum of 400 different IP addresses in the LAN Categorization is maintained by IBM. Neither IBM or LANCOM can guarantee full accuracy of the categorization. The Override function is only available for HTTP websites. The SIP ALG (Application Layer Gateway) acts as a proxy for SIP communication. For SIP calls the ALG opens the necessary ports for the corresponding media packets. Automatic address translation (STUN is no longer needed).

9 LAN protocols IP Interfaces Ethernet ports Port configuration USB 2.0 host port Serial interface Hardware Management and monitoring Management Management functions FirmSafe Monitoring Monitoring functions Monitoring statistics iperf SLA-Monitor (ICMP) SD-WLAN SD-LAN SD-WAN Hardware Power supply Environment Housing Fans Power consumption (max) Declarations of conformity* CE FCC Draeger validation IPv6 Country of Origin *) Note Scope of delivery CD/DVD ARP, proxy ARP, BOOTP, DHCP, DNS, HTTP, HTTPS, IP, ICMP, NTP/SNTP, NetBIOS, PPPoE (server), RADIUS, RIP-1, RIP-2, RTP, SIP, SNMP, TCP, TFTP, UDP, VRRP, VLAN 4 individual 10/100/1000 Mbps Ethernet ports. Ethernet ports can be electrically disabled within LCOS configuration Each Ethernet port can be freely configured (LAN, DMZ, WAN, monitor port, off). Additionally, external DSL modems or termination routers can be operated as a WAN port with load balancing and policy-based routing. USB 2.0 hi-speed host port for connecting USB printers (USB print server), serial devices (COM port server), USB data storage (FAT file system); bi-directional data exchange is possible Serial configuration interface / COM port (8 pin Mini-DIN): 9, ,000 baud, suitable for optional connection of analog/gprs modems. Supports internal COM port server and allows for transparent asynchronous transmission of serial data via TCP LANCOM Management Cloud, LANconfig, WEBconfig, WLAN controller, LANCOM Layer 2 management (emergency management) Alternative boot configuration, voluntary automatic updates for LCMS and LCOS, individual access and function rights up to 16 administrators, RADIUS and RADSEC user management, remote access (WAN or (W)LAN, access rights (read/write) adjustable seperately), SSL, SSH, HTTPS, Telnet, TFTP, SNMP, HTTP, access rights via TACACS+, scripting, timed control of all parameters and actions through cron job Two stored firmware versions, incl. test mode for firmware updates LANCOM Management Cloud, LANmonitor, WLANmonitor Device SYSLOG, SNMPv1,v2c,v3 incl. SNMP-TRAPS, extensive LOG and TRACE options, PING and TRACEROUTE for checking connections, internal logging buffer for firewall events Extensive Ethernet, IP and DNS statistics; SYSLOG error counter, accounting information exportable via LANmonitor and SYSLOG, Layer 7 Application Detection including application-centric tracking of traffic volume iperf is a tool for measurements of the bandwidth on IP networks (integrated client and server) Performance monitoring of connections SD-WLAN automatic WLAN configuration via the LANCOM Management Cloud SD-LAN automatic LAN configuration via the LANCOM Management Cloud SD-WAN automatic WAN configuration via the LANCOM Management Cloud Internal power supply unit ( V, Hz) Temperature range 5 40 C; humidity 0 95%; non-condensing Robust metal housing, 19" 1 HU, 435 x 45 x 207 mm, with removable mounting brackets, network connectors on the front 1 30 watt EN , EN 55022, EN FCC Part 15, Class B with FTP cabling Approved compatibility for use in Infinity OneNet installations with Dräger patient monitors in medical environments. IPv6 Ready Gold Made in Germany You will find all declarations of conformity in the products section of our website at Data medium with management software (LANconfig, LANmonitor, WLANmonitor, LANCAPI) and documentation

10 Scope of delivery Cable Cable Cable Support Warranty Software updates Options LANCOM Warranty Basic Option L LANCOM Warranty Advanced Option L LANCOM Public Spot XL LANCOM Public Spot PMS Accounting Plus LANCOM WLC AP Upgrade +10 LANCOM WLC AP Upgrade +25 LANCOM Management Cloud LANCOM LMC-D-1Y LMC License LANCOM LMC-D-3Y LMC License LANCOM LMC-D-5Y LMC License Item number(s) LANCOM WLC (EU) LANCOM WLC (UK) LANCOM WLC (US)* Serial configuration cable, 1.5m 1 Ethernet cable, 3 m IEC power cord 3 years support Regular free updates (LCOS operating system and LANtools) via Internet +10 user, 1 year subscription, item no user, 1 year subscription, item no user, 1 year subscription, item no user, 3 year subscription, item no user, 3 year subscription, item no user, 3 year subscription, item no Option to extend the manufacturer s warranty from 3 to 5 years, item no Option to extend the manufacturer s warranty from 3 to 5 years and replacement of a defective device, item no Hotspot option for LANCOM WLC-4100, WLC-4025(+), LANCOM 9100(+) VPN, and LANCOM 7100(+) VPN for user authentication (recommended up to 2,500), versatile access (via voucher, , SMS), including a comfortable setup wizard, item no Extension of the LANCOM Public Spot (XL) Option for the connection to hotel billing systems with FIAS interface (such as Micros Fidelio) for authentication and billing of guest accesses for 178x/19xx routers, WLCs, and current central-site gateways, item no LANCOM WLC AP Upgrade +10 Option, enables your WLC to manage 10 Access Points/WLAN router in addition, item no LANCOM WLC AP Upgrade +25 Option, enables your WLC to manage 25 Access Points/WLAN router in addition, item-no LANCOM LMC-D-1Y License (1 Year), enables the management of one category D device for one year via the LANCOM Management Cloud, item no LANCOM LMC-D-3Y License (3 Years), enables the management of one category D device for three years via the LANCOM Management Cloud, item no LANCOM LMC-D-5Y License (5 Years), enables the management of one category D device for five years via the LANCOM Management Cloud, item no

11 Item number(s) LANCOM WLC High Availability Clustering XL Option Gehäusezeichnung LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 12/17 LANCOM Systems GmbH I Adenauerstr. 20/B2 I Wuerselen I Germany I info@lancom-systems.com