Gigabit PoE Injector Patch Panel

Transcription

1 Gigabit PoE Injector Patch Panel 1/4/8/12/16/24 Port Gigabit PoE Injector 1 ~ 24 Port Gigabit PoE Injector Patch Panel 제품사양및모양은제품성능향상을위해예고없이변경될수있습니다

2 Model Number: GPOE-1-AB 1 Port Gigabit Passive PoE Injector Mode A+B PoE Injector/Splitter Product Overview This device is a very cost effective injector at gigabit rates. When used as an injector it inserts the DC voltage at the source location. The DC voltage is then carried over the active data pairs in the network cable. The same device can be used as a passive splitter to extract two voltages from the ethernet cable while operating at gigabit speeds. Gigabit PoE injector or splitter, dual mode A and B, power on all 4 pairs, reversable polarity, polarity indicator LED. Power Supply Sold Seperately: Use any of our power supplies up to 56 volts, power supply not included, for up to 60 watts total Use with IP security cameras, phones, wireless access points and other devices that accept passive 802.3af or PoE+ Dual 650 maautomatic resettable fuses - one for each mode Port 1 Lan port, one PoE port Input 12-56V DC 2.1MM Output 12-56V PER PORT (60 watt max) Data 1/2&3/6, 4/5&7/8- Size 100 mm x 25mm x 22mm Data In Connects PC/HUB/Switch/Rotuer Weight 30g Ethernet Cable TIA/EIA 568 Cat. 5/5e/6/6e Data rate 10/100/1000Mbps Connector RJ-45 Operating Temp. -40 C ~ 70 C Storage Tempe. -40 C~+70 C Operating Humidity 10%~80%RH Storage Humidity 5%~90%RH

3 Model Number: POEGI004B 4port Gigabit Active Mode B(Mid span) Auto Nego. PoE injector Patch Panel Mix 10/100 & Gigabit rate and power on the same cable For 4 devices with 60 watts total power Power 802.3at devices 4 data in, 4 Data + PoE out This is not a switch - use it to add PoE to any switch Extend power to 328 ft (or 100 meters) Power is off until a compatible device is connected Specification 4 Port 802.3af and 802.3at compliant gigabit Ethernet Injector - no power unless a PoE device is attached - 4 Shielded RJ-45 LAN - 4 Shielded RJ-45 LAN+POE - all 4 data pairs active for gigabit data rates - shared data and power - supports 802.3at class 0, 1, 2, 3, 4 Wall mount Injector: 116 mm x 45mm x 25m(including 2x 10mm tabs ) 550 ma current limiter per port per 802.3at specifications No power is supplied to non-poe devices Same voltage to all ports after negotiation Use with any Ethernet switch - passes all management info transparently Ideal for IP Cameras, VOIP phone, WiFi Access Points with 802.3af or 802.3at Standard power connector - 2.1mm x 5.5mm Mode A power output via isolated transformer : pins 1-2 (-) - pins 3-6 (+) Applications WiFi Access points like Cisco, Meraki, Aruba ac IP Cameras like Hikvision any 802.3af or 802.3at Device USB, 5v and 12v, non-poe devices

4 Model Number: GPOE-8B 8 Port Gigabit PoE Patch Panel, Auto Nego. Mode B PoE Injector 8 Port Gigabit Ethernet Injector, 8 Shielded RJ-45 LAN / 8 Shielded RJ-45 LAN+POE 10/100/1000 data rates Injector: 180 mm x 45mm x 25mm including 2x 10mm tabs Power supply: 122mm x 53mm x 34mm plus 12mm on each side for the tab Wall mount - stackable 1000 ma automatic resettable fuse on each port Same voltage to all ports power is shared as needed by the devices Use with any Ethernet switch PoE or non-poe switches Standard power connector - 2.1mm x 5.5mm Additional Phoenix DC connector - 3.5mm model pin 2 (minus) pin 4 (plus) LED status indicator - Green standard polarity - Red for Reverse polarity Operating Temperature 0 to 65 deg C Mode B operation - pins 7,8 (-) / - pins 4,5 (+) Mode A passthru Ideal for IP Cameras, VOIP phone, WiFi Access Points Select the power supply you need 30, 60 or 120 watts Power is always on Application ac WiFi access points like Aruba, Cisco, Meraki IP Phones like Yealink Grandstream, Polycom etc IP Cameras like outdoor dome cameras any 802.3at Device

5 Model Number: GPOE-12-1U 12 Port Multi Port Gigabit 1U Rack mount Passive POE Injector Patch Panel 802.3af (15.4w)/ 802.3at (30w) 12 port Rack-mountable 1U POE Power Injector Panel 12 LAN ports, 12 LAN+Power(POE) ports, shielded 31 watt max each port, resettable fuse on each port Power VOIP phones, IP Cameras, WiFi AP, & more PDs Same voltage to all ports 2.1mm x 5.5mm for DC plug LED power light indicator Works with any ethernet switch or router,add PoE to switch Use any power supply to 48 volts, 24 volt, 12 volt, according to your need Plastic outside box Product Overview POE injector with normal switch can share the same function with POE switch but POE injector + normal switch are more cost-effective. This 12 Port gigabit PoE injector panel, which is a simple, cost-saving and convenient equipment for IP camera, IP phone, WiFi Access point. This 1000Mbps Power Over Ethernet Patch Panel can powered up to 12 Power Devices 100 meters far away from one power supply. The gigabit PoE injector panel can power PDs 100 meters from power source with safety, low-cost and easy installation. 24V 120W power adapter for 24V passive POE PDs, such as for MikroTik and 24V UBNT, 48V 120W power adapter for most IP camera, 802.3af/at WiFi AP. 12V 120W for 12V IP camera with POE splitters for the POE injector. Specification 1.The 12 port gigabit PoE injector is used 10/100/1000M Ethernet. The upper Rj45 sockets is for LAN/Switch/PC 1/2&3/6&4/5&7/8 are transmitting data. 2.The under RJ45 (power +data) socket is to deliver data & power:1/2&3/6&4/5&7/8 transmitting data,1/2(-)&3/6(+)for power. 3.The item is composed of 12 set of Rj45 sockets and two 60V DC power jack. Input power requests 120W or more AC to DC power converter. 4.The input dc hole diameter is 2.1mm and the other end Out Diameter 5.5mm. 5.Each socket provides protection against short overflow (current protection 650mA+/-15%) 6.The sum total output power must be lower than the MAX input power of AC-DC power converter. If not, it is necessary to consider taking higher AC-DC power converter. 7.There commended formula for AC-DC power converter is 10W per RJ45 set (1 set = 2 x RJ 45 sockets). For example, 12 x 10W = 120W for 12 port Passive PoE panel. 8.The configuration size of panel is 1U (height), 19 (width) and 52mm (thickness) as is available to answer market demand and convenient to be installed directly.

6 Model Number: ZQPOEGI Port Gigabit Passive POE injector mode A & Mode B RJ-45 for IP Camera / IP Phone Use 10/100/1000M GigaBit Ethernet Flexible power(dc 18-57V) For 1'U high standard rack mount 5 LED status indicators Use with any Ethernet switch 650mA automatic resettable fuse on each port Supports IEEE 802.3at or 802.3af devices Ideal for IP cameras,voip phone,wifi Access Points - Mode A operation-minus on pins1/2,plus on3/6(802.3af/at) - Mode B operation-minus on pins7/8,plus on4/5 Product Overview The 16 port gigabit PoE panel is used 10/100/1000M Ethernet, The upper Rj45 sockets is for LAN/Switch/PC 1/2 & 3/6 & 4/5 & 7/8 are transmitting data. The under RJ45 (power + data) socket is to deliver data and power: Mode A -1/2 & 3/6 Mode B -4/5 & 7/8.Passive POE is composed of 16 set of Rj45 sockets and two 60V DC power jack. Input power requests160w or more AC/DC Power. Standard power Connector - 2.1mm x 5.5mm Each socket provides protection against short overflow (current protection 650mA) The sum total output power must be lower than the MAX input power of AC / DA Power converter. If not, it is necessary to consider taking higher AC / DC Power converter. There commended formula for ac/dc power converter is 15W per RJ45 set (1set=2 x RJ45 sockets). For example, 16 x 15W = 240W for 16 port Passive PoE panel.the configuration size of panel is 1U (height), 19 (width) and 52mm (thickness), as is available to answer market demand and convenient to be installed directly. Specification Input Output Vac (18-57V Dc In) 18-57V Data 1/2 & 3/6 & 4/5 & 7/8 Power 3/6+ & 1/2-, 4/5+ & 7/8- Data In Weight Dimensions Case of material Connects PC/HUB/Switch 16 Port 1.3Kg 482.6mm 44.3mm 52mm metal work material Ethernet Cable TIA/EIA 568 Cat. 5 Data rate Connector 10/100/1000Mbps RJ-45 Operating Temperature 0 C ~ 40 C Storage Temperature Operating Humidity Storage Humidity -40 C~+70 C 10%~80%RH 5%~90%RH

7 Model Number:JT-2224M 24 port Gigabit PoE Mode B(Mid Span) injector Managed panel Specifications JT-2224M series are 24 port Mid Span power with remove management features Power over Ethernet injector 24 port Giga PoE Mid Span Managed power supply. JT-2224M series are 24 port Mid Span power. The design provides system Integrators to upgrade Core switch or Access switch PSE function. They can use the existing networking Management environment & definition without any change. JT-2224M series includes 12 and 24 port models. They are fully backward compatible to use with any PD device such as 19 Chassis Product Complying with IEEE Base-T,IEEE 802.3u 100Base-TX,IEEE802.3ab 1000Base-T Complying IEEE802.3at Supporting the power up to Max. 30Watt for each PSE/PoE port Providing Scalable 24 ports PoE 802.3af backward compatible. Web-based management Status LEDs: System Power, Link/Activity, and PoE/PSE on line Network Transmission Media: 10Base-T Cat5 UTP/STP; 100Base-TX Cat.5 UTP/STP Internal Power supply: AC input (90~260V/AC, 50~60Hz) UL Safety Operating Temperature: 0 C ~ 40 C Storing Temperature: -20 C ~ 90 C Humidity: 10% ~90% RH (Non-condensing) Dimension (L x W x H): 440mm x 220mm x 44mm (1U) Power supply : 250Watt Weight: 3.0Kg