Cisco Managing Industrial Networks for Manufacturing wit...

Size: px

Start display at page:

Download "Cisco Managing Industrial Networks for Manufacturing wit..."

Steven Newton
5 years ago
Views:

Cisco 200-601 Managing Industrial Networks for

1 Cisco Managing Industrial Networks for Manufacturing wit...

2 QUESTION: 80 If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays? A. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 4 Switch(config-alarm-prof)#relay minor 1 B. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 3 Switch(config-alarm-prof)#relay minor 1 C. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 3 D. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 4 Answer: A QUESTION: 81 Which describes a best practice rule for controlling traffic between the corporate network and the controls network? A. Outbound traffic from the control network to the corporate network and outbound traffic from the corporate network to the control network can be restricted based on source and destination address only. B. Outbound traffic from the corporate network to the control network should be restricted but outbound traffic from the control network to the corporate network should not be restricted. C. Outbound traffic from the control network to the corporate network should be restricted based on source and destination address and service only. D. Outbound traffic from the control network to the corporate network should be restricted based on source and destination address, service, and port. Answer: D QUESTION: 82 Refer to exhibit.

3 The administrator has configured the following device IP settings, but did not keep track of which ports the devices were connected to. The administrator is able to ping each device but needs to update the network documentation to include the switch and interface where each device is connected. The administrator does not want to walk to each device and switch to track down the information. Which steps below would you execute in sequence to document the switch and interface where each device is connected? 1. View the ARP table on L3SW1 2. View the ARP table on the administrator's station 3. View the ARP table on L2SW4 4. PING all the devices 5. View the MAC address table on all switches 6. View the MAC address table on the administrator's station A. 2,4,5 B. 2,5,4 C. 4,3,6 D. 4,1,5 Answer: D QUESTION: 83 Refer to the exhibit.

Network Faceplates have not been installed on the HMI and so you need to map a network based on information available from RSLinx. Which most accurately represents the network configuration? A.

4 Network Faceplates have not been installed on the HMI and so you need to map a network based on information available from RSLinx. Which most accurately represents the network configuration? A. ** Missing ** B. ** Missing ** C. ** Missing ** D. ** Missing ** Answer: B QUESTION: 84 Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?

5 A. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion. B. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion. C. CIP Motion requires a star topology which is not supported by REP. RPVST+ is a suitable resiliency protocol for CIP motion. D. REP convergence is not fast enough. RPVST+ is a suitable resiliency protocol for CIP motion. Answer: B QUESTION: 85 Which statement is correct regarding Media Redundancy Protocol (MRP) in a ring of ProfiNET devices? A. When a link fault is detected, MRP rings must converge in less than 100 milliseconds B. MRP defines two device roles, Media Redundancy Master and Media Redundancy Client C. MRP can support rings of up to 250 devices D. MRP is only supported on network switches Answer: B QUESTION: 86 Refer to the exhibit.

6 Which lines represent an I/O connection running at a 20ms RPI? A. 2919, 2923, 2926 B. 2920, 2926, 2929 C. 2922, 2929, 2935 D. 2914, 2915, 2916 Answer: A QUESTION: 87 Cisco Industrial Ethernet switches are capable of sending alarm messages to ProfiNET management stations using the ProfiNET-IO protocol. Which four are alarms that can be configured for an interface? (Choose four) A. Port Not Forwarding B. Port Not Operating C. Port LLDP Disabled D. Port QoS Disabled E. Port Duplex Mismatch F. Port FCS Errors Exceeded Threshold G. Port CRC Errors Exceeded Threshold H. Port Link Fault Answer: A, B, F, H

7 For More exams visit Kill your exam at First Attempt...Guaranteed!

Exam Questions

Exam Questions 200-601 IMINS2 Managing Industrial Networking for Manufacturing with Cisco Technologies https://www.2passeasy.com/dumps/200-601/ 1.Which option best describes the ProfiNET Discovery and