sip SonNet-Trend Issue 1, Jun Interface Range Technical Guide

Transcription

1 sip SonNet-Trend Issue 1, Jun Interface Range Technical Guide

2 Sontay Limited All rights reserved. No part of this document may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of the software that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by the information contained in this document. Printed: Jun in England

3 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY I

4 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

5 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note We also provide an interface to a BACnet BeMS. 3 Issue 1, Jun. 2014

6 3 INSTALLATION GUIDE... 9 Remember Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. DIP Switch Ethernet Port Reset Button USB2.0 Port (x2) 24VDC Power Supply Power LED Ready LED LAN Activity LED Status LEDs Mini-USB Port Serial Port LED s (P1 to P4) Serial Port 1 port per LED 4 Issue 1, Jun. 2014

7 3 INSTALLATION GUIDE... 9 Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 5 Issue 1, Jun. 2014

8 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

9 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 7 Issue 1, Jun. 2014

10 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. Power LED Ready LAN Activity Statu s 8 Issue 1, Jun. 2014

11 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 9 Issue 1, Jun. 2014

12 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches Caution The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). Reset DIP 10 Issue 1, Jun. 2014

13 3 INSTALLATION GUIDE... 9 Note The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 1.2 SYSTEM OVERVIEW 11 Issue 1, Jun. 2014

14 Serial Network SIP SonNet-Trend - Interface Range 3 INSTALLATION GUIDE... 9 The system architecture is shown below. IP Network OS11 OS26 OS50 Each viq presents the configured SonNet wireless End device as Trend controller. SonNet wireless End device values are transferred as Trend Sensor, Knob, Digital Input and Switch Modules 12 Issue 1, Jun. 2014

15 3 INSTALLATION GUIDE Issue 1, Jun. 2014

16 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 14 Issue 1, Jun. 2014

17 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. 15 Issue 1, Jun. 2014

18 24VDC Power Supply DIP Switch Ethernet Port Reset Button 32mm USB2.0 Port (x2) Power LED Front Panel Annunciation... Status 3 Ready LED Button 4mm and Switches... LEDs 4 LAN Activity 1.2 SYSTEM OVERVIEW... LED SonNet 7mm Network... Mini-USB Port 6 108mm Serial Port LEDs 12.5mm (P1 to P4) 25mm 2 HARDWARE GUIDE 78mm 90mm 102mm Serial Port This hardware provides an interface between devices communicating via an identified protocol, i.e. SonNet, and Trend products communicating including 963, IQ4, IQ3 or IQ2 and EINC or XTEND via Ethernet protocol. The unit should be installed in systems for monitoring and control purposes. General 16 Issue 1, Jun. 2014

19 Weight 330g per unit including DIN Rail clips 410g shipped including DIN Rail clips Power Input Power Consumption Default User name Default Password 24VDC ±15V regulated Admin (case-sensitive) password (case-sensitive) Hardware Details Button DIP Switch Indicators Ethernet Serial Reset 1 bank of 4 switches Power, System Ready, Ethernet LAN Activity, 4 x Serial Communications Activity (one per port) 1 x 10/100Mbps port via RJ45 connector with 1.5KV magnetic isolation 1 x TTY port via RJ45 connector, supporting connection to Sontay SonNet RF-RXS wireless receiver Note Only P1 is configured via the DIP Switch. USB 2 x USB2.0 compliant host ports supporting low-speed (1.5Mbps) and full-speed (12Mbps) data rate 17 Issue 1, Jun. 2014

20 SD Memory Card 1 x internal 2GB slot for storage expansion Environmental Storage Temperature Operating Temperature Regulations -20 to 80C (-4 to 176F), 0 to 90% Relative Humidity 0 to 70C (32 to 158F), 0 to 90% Relative Humidity CE Class A, FCC Class A, REACH (Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals - European Chemicals Agency), RoSH (Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment - EU Directive 2002/95/EC) RoHS BANNED SUBSTANCES MAXIMUM LIMIT (PPM) Cadmium (Cd) 100 Lead (Pb) 1000 Mercury (Hg) 1000 Hexavalent Chromium (Cr6+) 1000 Poly Brominate Byphenyls (PBB) Issue 1, Jun. 2014

21 RoHS BANNED SUBSTANCES Packing materials: Cadmium, Lead, Mercury, Hexavalent Chromium and its components < 100PPM MAXIMUM LIMIT (PPM) 100 Dispose of the product and packaging according to WEEE Directive at an appropriate recycling centre. All parts are recyclable. The printed circuit board may be sent to any PCB recovery contractor to recover any appropriate metals. 19 Issue 1, Jun. 2014

22 3 INSTALLATION GUIDE This section explains the process of fitting the product in the required position and location, and connecting the cables to ensure it can communicate via the Trend network and the connected devices. It will explain specific wiring conventions used by the connected communications protocols and the hardware fitted to the unit. Note The CE marking on a product indicates the product complies with all the applicable European directives and applicable standards. 3.1 INSTALLING THE UNIT This unit usually forms part of a larger assembly, and/or may be housed in a floor or wallmounted enclosure. Note When fitting this unit as part of a system, refer to the documentation accompanying the other equipment for details. Caution This unit MUST be mounted to a DIN Rail in an enclosure using a DIN Rail kit. To install the unit using the DIN Rail kit 20 Issue 1, Jun. 2014

23 1. Fit the DIN Rail kit to the bracket on each side of the unit using the fixings supplied. 2. Simply click the unit, complete with the DIN Rail kit, onto the DIN Rail mounted in the enclosure. Screw Din Rail Clip Din Rail Mounting Kit Screw 21 Issue 1, Jun. 2014

24 Connect the power supply to the unit (see Connections and Wiring). Caution Before connecting power, ensure all connections have been verified and the V- (0V) is NOT earthed/grounded. Note A beep indicates the unit has started to boot up. 4. Connect this unit to the IP network using an appropriate Cat5e cable (see Connections and Wiring). 5. Connect this unit to the SonNet RF-RXS wireless receiver using an appropriate cable, (see Connections and Wiring). Remember The DIP Switches must be configured for connection to the SonNet RF-RXS wireless receiver, i.e. RS232 (see Connections and Wiring). 6. Configure the unit, including parameters required to permit communications via both the Ethernet and connection to the SonNet RF-RXS wireless receiver networks using the Configuration web pages (see Error! Not a valid bookmark self-reference.). 22 Issue 1, Jun. 2014

25 3.2 HARDWARE CONTROL The unit is fitted with 1 switchbank of 4 poles that are used to define the Serial port interface. It will be set to RS232 by default. A combination of pole 1 (SW1:p1) and pole 2 (SW1:p2) are used to configure the communications standard of Serial port 1 (P1). The switch 3 (SW1:p3) and switch 4 (SW1:p4) are not supported. 1 DI 2 3 ON 4 SWITCH NO. (SW1) RS232 SIGNAL 1 (SW1:p1) ON 2 (SW1:p2) ON 3 (SW1:p3) N/A 4 (SW1:p4) N/A Note This unit also supports RS485 (2-wire+Gnd), and RS422 (4-wire+Gnd). However, these wiring standards are not applicable to the SonNet RX-RFS wireless receiver. 23 Issue 1, Jun. 2014

26 3.2.1 Connections and Wiring This unit may be supplied mounted in an enclosure or supplied as an individual part in kit form. Generally the unit will be installed as part of a control system using an Ethernet hub/switch. Category 5 cables may be used for individual line lengths of up to 100 metres. Caution Before connecting power to this unit, please ensure the Ethernet and Serial connections have been verified and the V- terminal (0 Volts) of the power connector is NOT earthed/grounded Power Supply Each unit requires a 24VDC power supply attached to the connector. If the power is correctly supplied the Power LED is illuminated and the real-time clock (RTC) will be maintained. Note The unit contains a supercapacitor that maintains the real-time clock for a maximum of 3 days. V- V+ 24VDC Power Supply 24 Issue 1, Jun. 2014

27 3.2.3 Communications The RJ45 port(s), indicated by the symbol, is designed for Ethernet LAN, whereas the RJ45 ports at the opposite end of the unit supports M-Bus communications. Ethernet Communication Port Each unit contains 10/100base T port for Ethernet communications via a standard RJ45 type connector. Connection to an Ethernet hub/switch requires a Category 5 RJ45-to-RJ45 cable assembly. When connecting to the Ethernet hub/switch, a straight-through cable is used. RJ45 MALE Pin 1 FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 1 Transmit+ White/Orange 1 2 Transmit- Orange 2 3 Receive+ White/Green 3 4 N/A Blue 4 5 N/A White/Blue 5 6 Receive- Green 6 TO RJ45 PIN NO. 25 Issue 1, Jun. 2014

28 RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 7 N/A White/Brown 7 8 N/A Brown 8 TO RJ45 PIN NO. The image shows the flat side of RJ45 plug. When connecting directly to another device supporting 10/100base T Ethernet communications protocol, i.e. a laptop or computer used to configure and interrogate the unit, a crossover cable is required. RJ45 MALE Pin 1 FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 1 Transmit+ White/Orange 3 2 Transmit- Orange 6 3 Receive+ White/Green 1 4 N/A Blue 4 5 N/A White/Blue 5 6 Receive- Green 2 7 N/A White/Brown 7 TO RJ45 PIN NO. 26 Issue 1, Jun. 2014

29 RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 8 N/A Brown 8 TO RJ45 PIN NO. The image shows the flat side of RJ45 plug. 27 Issue 1, Jun. 2014

30 SonNet Communication Port Each unit contains RJ45 communication port that is used to establish communications with the connected SonNet RF-RXS wireless receiver. Serial port 1 (P1) is configured to support a RS232 communications standard. This is determined by the position of the SW1:p1 and SW1:p2 DIP switches. Note This unit also supports RS485 (2-wire+Gnd), and RS422 (4-wire+Gnd). These wiring standards are not applicable to the SonNet RX-RFS wireless receiver. FROM RJ45 PIN NO. RS232 SIGNAL SONNET RF-RXS 9-WAY D -TYPE Pin 1 1 (White/Orange) DSR* 1 2 (Orange) RTS 2 3 (White/Green) GND 3 4 (Blue) TXD 4 5 (White/Blue) RXD 5 6 (Green) DCD* 6 7 (White/Brown) CTS 7 8 (Brown) DTR* 8 28 Issue 1, Jun. 2014

31 FROM RJ45 PIN NO. RS232 SIGNAL SONNET RF-RXS 9-WAY D -TYPE 9 Note The image shows the flat side of RJ45 plug. * indicates the signal is only available from Port 2 on RS232. CONNECTOR TYPES AND CABLES Shielded RJ45 connectors and screened Category 5 cables are widely available, however, specifications vary. In view of the problems that can arise with inadequate cabling, it is strongly recommended that ready-made interconnecting cables are used. 29 Issue 1, Jun. 2014

32 3.2.4 Hardware Expansion The unit is fitted with connections that support additional hardware to be connected to the unit. USB Port The USB host ports, indicated by the are USB2.0 high speed host ports. symbol, If necessary, you may be instructed to use these ports to transfer a file to the unit using a USB Flash device. The unit currently supports, USB Storage Device Note Contact the Sales/Service Engineer/Technical Support for details. USB Port Mini-USB Port This is not supported and will be obstructed by a label. 30 Issue 1, Jun. 2014

33 4 CONFIGURATION GUIDE This section will describe the process of allowing the data recorded by SonNet End devices connected to a SonNet RF-RXS wireless receiver communicating with this product to be monitored by the BeMS. It will explain the specific configuration, used to identify each End device in this product of the communication protocols used by the hardware connected to the product of the parameters used to specify the data that will be accessed by the Trend BeMS 4.1 THE CONFIGURATION PAGES Each product can only be configured via a number of associated Configuration pages. The pages are password protected to prevent unauthorised access to the parameters that define the operation of this product. Note The interface configuration pages operate using HTML5 making the pages available via a number of hardware variants. Remember The Configuration options, available from a fly out on the left side of the screen includes the Map points page used to determine the link the required End device parameters, to a specific viq OS module. viq used to determine the connection to the Trend network and display the value from a defined End device parameters. viq Calculator page used to manipulate an output value from a selected viq OS module that can be written to another viq OS module. Local IP settings page used to define the unique identity of this product on the IP (Internet Protocol) network. Comms settings page to define the communications parameters used when connected to the SonNet RF-RXS wireless receiver and the connection to the Trend network. All changes MUST be confirmed using Save (or Save and reboot ). 31 Issue 1, Jun. 2014

34 4.2 CONNECT TO THIS PRODUCT When this product has been correctly installed (see 32 Issue 1, Jun. 2014

35 33 Issue 1, Jun. 2014

36 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

37 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

38 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

39 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

40 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

41 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

42 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

43 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

44 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

45 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

46 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

47 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. 8 Issue 1, Jun. 2014

48 6 HARDWARE GUIDE This hardware provides an interface between devices communicating via an identified protocol, i.e. SonNet, and Trend products communicating including 963, IQ4, IQ3 or IQ2 and EINC or XTEND via Ethernet protocol. The unit should be installed in systems for monitoring and control purposes. General Weight Power Input Power Consumption Default User name Default Password 330g per unit including DIN Rail clips 410g shipped including DIN Rail clips 24VDC ±15V regulated Admin (case-sensitive) password (case-sensitive) Hardware Details Button DIP Switch Reset 1 bank of 4 switches 10 Issue 1, Jun. 2014

49 Indicators Power, System Ready, Ethernet LAN Activity, 4 x Serial Communications Activity (one per port) Ethernet Serial 1 x 10/100Mbps port via RJ45 connector with 1.5KV magnetic isolation 1 x TTY port via RJ45 connector, supporting connection to Sontay SonNet RF-RXS wireless receiver Note Only P1 is configured via the DIP Switch. USB SD Memory Card 2 x USB2.0 compliant host ports supporting low-speed (1.5Mbps) and full-speed (12Mbps) data rate 1 x internal 2GB slot for storage expansion Environmental Storage Temperature Operating Temperature Regulations -20 to 80C (-4 to 176F), 0 to 90% Relative Humidity 0 to 70C (32 to 158F), 0 to 90% Relative Humidity CE Class A, FCC Class A, REACH (Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals - European Chemicals Agency), RoSH (Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment - EU Directive 2002/95/EC) 10 Issue 1, Jun. 2014

50 RoHS BANNED SUBSTANCES MAXIMUM LIMIT (PPM) Cadmium (Cd) 100 Lead (Pb) 1000 Mercury (Hg) 1000 Hexavalent Chromium (Cr6+) 1000 Poly Brominate Byphenyls (PBB) 100 Packing materials: Cadmium, Lead, Mercury, Hexavalent Chromium and its components < 100PPM 100 Dispose of the product and packaging according to WEEE Directive at an appropriate recycling centre. All parts are recyclable. The printed circuit board may be sent to any PCB recovery contractor to recover any appropriate metals. Installation Guide) the communication protocols and the required parameters must be configured. 10 Issue 1, Jun. 2014

51 Note Each product is supplied with a default IP address. This is used to identify the product on the IP network and it must be changed and assigned a unique IP address according to local company network policy. Before configuring this product, ensure it and the computer are in the same IP range. Typically, a fixed IP address is used because the computer performs communications with individual products. The computers IP address is displayed on the TCP/IP Properties dialog by selecting, Start > Control Panel > Network Connections > Local Area Connection > Properties > TCP/IP > Properties To connect to this product After physically connecting the computer to this product using an appropriate Cat 5e cable (see 10 Issue 1, Jun. 2014

52 10 Issue 1, Jun. 2014

53 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

54 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

55 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

56 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

57 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

58 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

59 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

60 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

61 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

62 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

63 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

64 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. 8 Issue 1, Jun. 2014

65 8 HARDWARE GUIDE This hardware provides an interface between devices communicating via an identified protocol, i.e. SonNet, and Trend products communicating including 963, IQ4, IQ3 or IQ2 and EINC or XTEND via Ethernet protocol. The unit should be installed in systems for monitoring and control purposes. General Weight Power Input Power Consumption Default User name Default Password 330g per unit including DIN Rail clips 410g shipped including DIN Rail clips 24VDC ±15V regulated Admin (case-sensitive) password (case-sensitive) Hardware Details Button DIP Switch Reset 1 bank of 4 switches 10 Issue 1, Jun. 2014

66 Indicators Power, System Ready, Ethernet LAN Activity, 4 x Serial Communications Activity (one per port) Ethernet Serial 1 x 10/100Mbps port via RJ45 connector with 1.5KV magnetic isolation 1 x TTY port via RJ45 connector, supporting connection to Sontay SonNet RF-RXS wireless receiver Note Only P1 is configured via the DIP Switch. USB SD Memory Card 2 x USB2.0 compliant host ports supporting low-speed (1.5Mbps) and full-speed (12Mbps) data rate 1 x internal 2GB slot for storage expansion Environmental Storage Temperature Operating Temperature Regulations -20 to 80C (-4 to 176F), 0 to 90% Relative Humidity 0 to 70C (32 to 158F), 0 to 90% Relative Humidity CE Class A, FCC Class A, REACH (Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals - European Chemicals Agency), RoSH (Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment - EU Directive 2002/95/EC) 10 Issue 1, Jun. 2014

67 RoHS BANNED SUBSTANCES MAXIMUM LIMIT (PPM) Cadmium (Cd) 100 Lead (Pb) 1000 Mercury (Hg) 1000 Hexavalent Chromium (Cr6+) 1000 Poly Brominate Byphenyls (PBB) 100 Packing materials: Cadmium, Lead, Mercury, Hexavalent Chromium and its components < 100PPM 100 Dispose of the product and packaging according to WEEE Directive at an appropriate recycling centre. All parts are recyclable. The printed circuit board may be sent to any PCB recovery contractor to recover any appropriate metals. Installation Guide), open a web browser application. 10 Issue 1, Jun. 2014

68 Tip! Mozilla Firefox is the recommended web browser as it provides a faster, safer, and smarter display of the parameters, but other browsers can be used. Safari is not compatible with this product. Type the required IP address. An IP address must be entered using the standard 32-bit dotted-decimal notation. Default IP address ( ) Note SIP Search (our SIP detection tool) is available from the web site ( via the Customer Login section. Alternatively, contact support@synapsys-solutions.com. The Login page will appear. Alternatively, launch the Configuration Tool in the default web browser by selecting Start > All Programs > Accessories > Run and type the default IP address, including (see 10 Issue 1, Jun. 2014

69 10 Issue 1, Jun. 2014

70 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

71 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

72 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

73 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

74 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

75 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

76 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

77 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

78 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

79 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

80 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

81 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. Hardware Guide) in the dialog that appears. The Login page is displayed. Note The product can also be installed in a secure site. Type address> and confirm the secure certification request as necessary. However, this will provide 8 Issue 1, Jun. 2014

82 a slower reaction time and the Restore feature is disabled when accessed via a secure configuration. Enter the User name and Password (see 8 Issue 1, Jun. 2014

83 8 Issue 1, Jun. 2014

84 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

85 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

86 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

87 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

88 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

89 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

90 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

91 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

92 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

93 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

94 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

95 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. Tip! Hardware Guide) and press Login to display the Home page. If the Login page fails to appear, check this product is connected to the IP network and communications has been established. Press Refresh to verify the connection. 8 Issue 1, Jun. 2014

96 This product is ready to be configured when the communication interface parameter options appear on the computer screen. Tip! Note If the valid User name and Password fails to launch the configuration page, clear the web browser cache (generally <Ctrl>+<Shift>+<Del> will display the Delete browsing history dialog). Press Refresh to verify the connection. If necessary, acknowledge the Time mismatch warning dialog. This indicates the time currently set in this product differs from the time currently set in the PC by more than 5 mins. This warning only appears after the correct User name and Password is entered on the Login page and will not appear again until the browser is reloaded or refreshed. The Welcome page is displayed. If necessary, press to show the web page providing support documentation and SIP Search (the SIP detection tool). If necessary, press to display the web page version currently loaded and operational. If necessary, press Admin to display the Change password page. 8 Issue 1, Jun. 2014

97 10.3 CONFIGURE THE COMMS INTERFACE The Map points, IP settings, and Comms settings parameters are used to configure the communication protocols used to transmit data between the SonNet RF-RXS wireless receiver and this product. The Back up and restore parameters generate a copy (back up) of the configuration that should be kept in a secure environment (not with the computer) protecting it from user error, hardware failure, and other problems. A back up copy can be used to restore the configuration to a usable state following a serious data loss, i.e. disaster recovery. Note The IP address, Subnet mask, and Default gateway must be configured according to local network policy Configure the Local IP Settings 1. Press to reveal the configuration options from the left side of the screen and select Local IP settings to display the Transmission Control Protocol and Internet Protocol (TCP/IP) parameters that identify this unit on the IP Network. It is the communication protocol used for networks, including the Internet. A specific range of configured IP addresses can be used to group units in networks or subnets. Note Note Alternatively, move the cursor to the left side of the screen to display a list of available configuration options. This also applies when using a tablet. If necessary, change the Hostname. This is a maximum 15 character label (including - and _ ) and numbers, assigned to this product and linked to the IP address which may be derived from the DHCP ( DHCP enabled is On ). The Broadcast IP is the logical address used for datagrams to all connected IP devices. 8 Issue 1, Jun. 2014

98 2. Change the IP address, Subnet mask, and Default gateway according to local network policy. This provides a unique identification of a product in the defined Subnet Mask on the IP network. The Subnet Mask is a configurable range of accessible IP addresses and the Default Gateway is used to direct communications to IP addresses not in the defined Subnet Mask. (LAN 1) Subnet 1 = IP address to (Subnet Mask ) (LAN 2) Subnet 2 = IP address to (Subnet Mask ) Gateway = (LAN 3) Subnet 3 = IP address to (Subnet Mask ) (LAN 5) Subnet 1 = IP address to (Subnet Mask , Gateway ) (LAN 4) Subnet 4 = IP address to (Subnet Mask ) Remember If necessary, change the DHCP (Dynamic Host Configuration Protocol) configuration. This is a computer networking protocol used by devices (DHCP clients, i.e. this product) on a network to automatically obtain IP address from a DHCP server. Typically, an IP address is retained until the device is rebooted. When On the IP network parameters are assigned by the DHCP server. If necessary, change the DNS server (Domain Name System). This is the IP address of the server that manages the translation of the configured Hostname into an IP Address that may change if DHCP Enabled is set On. Hostname = SIP DHCP server ( ) SIP = IP address assigned by DHCP server DNS server ( ) The DNS server may need to be configured to support non-microsoft clients. If necessary, change the NetBIOS (Network Basic Input/Output System) configuration. This manages the IP address and Hostname (NetBIOS name) resolution of each device via the DNS server. Typically, this will only be enabled ( On ) when multiple SIP products have the same 15 character Hostname. 3. Press Save and reboot to confirm the IP Config changes and restart this product. It automatically restarts (as confirmed by a beep ) and loads the Login page. 8 Issue 1, Jun. 2014

99 Configure the Comms Settings The Comms settings page is divided in to 2 (two) sections. The parameters on the left define the physical connection between this product and the SonNet RF-RXS wireless receiver. The parameters on the right define the connection between this product and the Trend network. 4. Press to reveal the configuration options from the left side of the screen, and select Comms settings. This is used to configure the communication setup with the SonNet and Trend networks. 5. Configure the SonNet connection settings. These settings define the communications standard that must be used by all devices connected to this product. Select the required Port number. This is the serial port connecting this product to the SonNet RF-RXS wireless receiver and should always be 1. If necessary, configure the Zero values on Comms failure to determine the action required when a communications failure is detected. 6. Set Zero values on Comms failure to On to force the logged values to appear as 0 (zero) when a communications failure is detected. If Off the displayed values remain at the last logged value. 8 Issue 1, Jun. 2014

100 7. Configure the Trend connection settings. These parameters define the type of connection to the Trend network. Select the required Connection type to determine the data collector used, i.e. viq, Ethernet or Serial. Select viq to pass data to the internal virtual OS, there are no additional parameters. Note Tip! Select Ethernet to pass data to a defined IQ3 Trend controller. This Trend controller is defined by the IP address and IP port parameters. The IP address must be configured according to local company network policy. The standard Ethernet loopback settings ( ) are displayed by default. Select Serial to pass data to a defined IQ2 Trend controller. This Trend controller is defined by the Port number and Baudrate parameters. Caution The Port number must NOT be 1 because this is connected to the SonNet RF-RXS wireless receiver. The Baudrate parameter must be set according to the IQ2 Trend controller. 8. Press Save to confirm the Comms settings changes. 8 Issue 1, Jun. 2014

101 Configure the Map points The Map points page displays settings used to assign SonNet End device and selected parameters to a specific virtual OS ( viq ) and module Index Number, respectively. To map SonNet End device parameters 9. Press to reveal the configuration options from the left side of the screen and select Map points to display a table that will be configured to show selected SonNet End device parameters. Caution Tip! The SonNet devices network map shows all the Sonnet devices authorised by the SonNet RF-RXS wireless receiver. SonNet End devices MUST be authorised before commissioning this product. A list of detected SonNet End devices are automatically displayed in the SonNet devices network map on the left of the Map points page. Use to update the map of all authorised SonNet End devices. This occurs automatically at startup. Use to update the details of the authorised SonNet End devices. The End devices icon to the left of the device name indicates what is known about the device, but may take up to 15mins to completely update. Note SonNet End device parameters display a colour-coded icon next to the parameter name according to the current state of configuration. A yellow icon indicates the parameter is included in the Map points page but is NOT saved yet, a green icon indicates the parameter is included in the Map points page and saved. 8 Issue 1, Jun. 2014

102 10. Map a SonNet End device parameter to a viq OS and Module. i. Select the required End device to show the list of specifically related parameters, e.g. Temperature, Humidity, and Setpoint, etc. Tip! Caution If a required SonNet End device appears disabled (grey highlight), select all unnecessary End devices, select Delete device from the popup menu and press Refresh. This will promote the required SonNet End device in the list shown on the map. Any End device highlighted red is not available to this unit. Typically, the End device is NOT authorised or the SonNet RF-RXS wireless receiver is not connected. If necessary, manage the available Sonnet End devices authorised in the SonNet RF-RXS wireless receiver. Select Delete device to remove the selected SonNet End device from the list of available SonNet End devices in the map. Select Details to show information related to the selected SonNet End device. 8 Issue 1, Jun. 2014

103 ii. Select the required SonNet End device parameter and press (as shown above) to add it to the Map points page table. This will automatically assign the selected End device parameter to the defined Trend LAN and OS (according to the value at the top of the LAN and OS column). The Mod(ule) type is defined automatically according to the selected End device parameter and Num (ber) according to the number at the top of the Num column, e.g. Temperature - S (ensor) 1. Tip! LAN should show 0 when writing values to viq OS s. Edit the viq OS number at the top of the table column to define the configuration of the next selected End device parameter. SONNET POINT MOD. PAGE IN VIQ DESCRIPTION Temperature S Sensors configuration page Read only analogue value Setpoint K Knobs configuration page Read/Write analogue value VFC (Volt-Free Contact) I Digital Inputs configuration page Read only digital (1/0) value Switch W Switches configuration page Read/Write digital (1/0) value If necessary, amend the OS number to identify the viq OS that will show the parameter value provided by the End device. If necessary, press Trend Security to display a dialog that is used to configure the minimum level of authorisation required to allow Text comms to change module parameters (see Configure the Module Authorisation). 11. Press Save to confirm the Map points page changes. 8 Issue 1, Jun. 2014

104 CONFIGURE THE MODULE AUTHORISATION Occasionally authorisation may be used to control which users are permitted to change Trend Knobs and Switches module parameters in a specific group of OSs. Groups of one or more OSs can be protected using a Pin number, associated with a Pin level. The Trend Knobs and Switches module value will only be changed when a valid pin number is entered. Note The Pin Number and Pin Level are configured via the Users page in the viq configuration pages. 12. Press on the Map points page to display the Trend Security dialog. This dialog shows the OS (LAN and OS number) associated with the configured Pin number. i. Press to create a required Pin number configuration. Associated Pin Number viq OS requiring defined Pin number Caution Pin Level security is only enabled if the Users configuration page in the viq configuration pages is defined. ii. Enter a required pin number, i.e. a 4 (four) digit number defined on the Users page in the viq configuration pages, (see Configure the Pin Level Authorisation). Note Press to delete the Trend security Pin number configuration. iii. Press Choose Lan & OS and select the required viq OSs from the list of available OSs, as necessary. Note Press to remove the viq OS from the Trend security Pin number configuration. 13. Press Save to confirm the Trend Security changes. 8 Issue 1, Jun. 2014

105 Configure the Back up and Restore The Back up function generates a copy of the configuration in this product to be protected in a secure environment protecting it from user error, hardware failure, and other problems. It creates a back up of the configuration (IP settings, Comms settings, SonNet End devices, mapping to viq OS, viq OS configuration, and Sensors plot files) to a defined media/location which can be used to restore this product to an earlier state (see Restore a Previous Configuration). Tip! Use (Save Plots to Flash on the viq Pages ) before performing a Back up. This ensures the latest values are saved (in the plot) and may prevent the loss of data before using the Restore function. Remember Use the back up function ( Back up and restore page), after checking the configuration changes operate correctly and before performing any additional changes. This will ensure this product can be restored to a known operating condition without losing excessive data if it is not possible to complete the configuration changes. The Restore function supports the use of A Back up file to restore the configuration to a usable state following a serious data loss, i.e. disaster recovery An Update file (available from Technical Support) to update the product firmware that improves functionality. CREATE A BACK UP FILE To create a back up file 14. Press to reveal the configuration options from the left side of the screen and select Backup and restore to display the site management page. 15. Press Back up to automatically create a site configuration file. When the file has been created, save the file to an appropriate location. Note Instructions for saving the Backup file to a known location is dependent on the web browser and hardware being used. RESTORE A PREVIOUS CONFIGURATION 8 Issue 1, Jun. 2014

106 The Restore function allows this product to be returned to an earlier state without losing data. This is useful if it is not operating correctly because of a configuration change or a problem with an application, i.e. file loss and data corruption, but is most useful for disaster recovery if this product fails completely. By restoring to an earlier state (a version before it began to display problems) it may be possible to resolve the problems caused by a serious system issue or data loss. However, the restore function can also be used to configure another unit before it is fitted to an existing system, reducing the repeat engineering time. Remember This feature is also used to apply update files as necessary. To restore a back up file 16. Press to reveal the configuration options from the left side of the screen and select Backup and restore to display the site management page. 17. Press Restore to launch a browse dialog. 18. Locate and select the required back up/update file, and press Open to confirm the operation. This will extract the information contained in the back up file and overwrite the configuration already existing in this product. Note This product beeps steadily while the Backup or Upgrade files are being loaded. A fanfare indicates this is complete and it automatically restarts. 8 Issue 1, Jun. 2014

107 10.4 MANAGE THE LOGIN SECURITY When installed, the configuration web pages are protected by a User name and default Password (see 8 Issue 1, Jun. 2014

108 8 Issue 1, Jun. 2014

109 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

110 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

111 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

112 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

113 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

114 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

115 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

116 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

117 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

118 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

119 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

120 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. Hardware Guide). A valid User name and Password must be entered before authorised access to the configuration of this product is permitted. Tip! Change the Password parameter to prevent unauthorised access. 8 Issue 1, Jun. 2014

121 Caution Changing and retaining the Password is the responsibility of the customer. However, it may be possible to restore the default password, contact Technical Support. To change the default password 19. Press Admin (on the Welcome page or the, top right corner) to launch the Change user password page. This page displays the User name, Password and New password parameters allowing the user to change the current Password. Note Caution iv. Logout provides immediate exit from the Change password page. Enter the default value (Admin) in the User name. This parameter only supports the default User name. v. Enter the current password in the Password. Entering the valid password verifies the user is authorised to change the password. Login security can only be successfully controlled if the password is carefully distributed. 13 Issue 1, Jun. 2014

122 vi. Enter a new password (15 characters max.) in the New Password. This password overwrites the previous password value. Tip! vii. A random combination of upper and lower case characters and numbers provide the most secure password setup. Press Login to confirm the changes to the login security. This will now only allow access to this product configuration if the new password is used. 20. Press Logout to exit the current screen and automatically display the Login page. 14 Issue 1, Jun. 2014

123 12 VIQ CONFIGURATION GUIDE Each viq OS (out-station) corresponds to a group of points from connected to this product and is configured via the viq configuration pages. The viq stores a network of virtual Trend OSs that mimics the third party devices connected to the network and provides information that defines each OS, and the values recorded at the configured protocol dependant parameter. viq OS Icons Save Plots Dialog LAN Configuration Dialog Remote Site Configuration Dialog Trend Network Status Dialog Module Details Trend Local Area Network Note Values will start to appear soon after an Index number is first mapped to a Module number on the Map points page and a Label is entered on the appropriate Trend Module page. To configure the virtual Trend network 21. Press to reveal the configuration pages and select viq from the list of available options. Tip! Alternatively, move your cursor to the left side of the browser to show the Configuration options. 15 Issue 1, Jun. 2014

124 22. Create a virtual Trend network of virtual OSs (viq). Each viq presents a mapped device as a virtual Trend IQ3 controller on the Trend network. viii. Press, showing the Trend LAN currently used by the configured OSs in the product, to display a page for editing the LAN number. Tip! To reduce the occurrences of duplicate LAN numbers on the Trend network, it may be useful to use the last 2 digits of this products IP address as the LAN number, i.e. nnn.nnn.nnn.123 is LAN 123. Tip! Note ix. Create a virtual OS. The OS number identifies the corresponding device, defined on the Map points page, on the Trend network. Enter the required OS number and press Add OS to confirm. Start OS numbers at 11 (up to 119). viqs (Nodes) 2, 3 and 10 are reserved. When the fifth OS has been created a scroll bar appears. Virtual OSs can be deleted or duplicated by selecting the appropriate option from the context menu. The total number of virtual OSs is shown on the top left of the page with a scroll bar (orange bar) to show further virtual OSs. 23. Configure the Trend Address module details (see 16 Issue 1, Jun. 2014

125 17 Issue 1, Jun. 2014

126 Error! Reference source not found. - Technical Guide 1.1 THE UNIT Front Panel Annunciation Button and Switches SYSTEM OVERVIEW SonNet Network Trend Network HARDWARE GUIDE INSTALLATION GUIDE INSTALLING THE UNIT HARDWARE CONTROL Connections and Wiring Power Supply Communications Hardware Expansion CONFIGURATION GUIDE THE CONFIGURATION PAGES CONNECT TO THIS PRODUCT CONFIGURE THE COMMS INTERFACE Configure the Local IP Settings Configure the Comms Settings Configure the Map points Configure the Back up and Restore MANAGE THE LOGIN SECURITY II

127 Error! Reference source not found. - Technical Guide 5 VIQ CONFIGURATION GUIDE Configure the VCNCs Configure the Time and Date Configure the UDP Group Configure the GUID Save Plots to Flash Check the Network Status Configure the Address Module Configure a Sensors Module Configure a Digital Inputs Module Configure a Knobs Module Configure a Switches Module Configure the Pin Level Authorisation USE THE VIQ CALCULATOR Create the viq Calculation Configure the viq Calculation Configure the Frequency schedule Replicate an Existing viq Calculation TROUBLESHOOTING ORDER CODE ACCESSORIES II

128 3 INSTALLATION GUIDE INTRODUCTION This is a miniature computing platform that can be installed as part of a Trend BeMS (Building energy Management System). It has been specifically designed to easily interface between the Sontay SonNet Wireless Receiver, and a Trend BeMS (Building energy Management System). It supports SonNet proprietary protocol via P1 direct connection to Trend network allowing devices to appear as a Trend IQ3 controller via the Ethernet port standard or IP alarm conditions Note Remember We also provide an interface to a BACnet BeMS. Energy metering is compulsory for buildings of a floor area >500M 2. The owner must be able to account for 90% of the consumed energy from each system, i.e. heat, gas, lighting, water and electricity. Remember Typically, individual systems (energy control, lighting, boiler and air conditioning system, etc.) are individually measured for CO2 accountability. So, installing this 8 Issue 1, Jun. 2014

129 3 INSTALLATION GUIDE... 9 unit and combining the individual systems can help an effective BMS be more energy efficient and comply with April 2006 Part L2 Building Regulations. This product exposes information from SonNet End devices via its connection to a single SonNet RF-RXS wireless receiver to the Trend BMS. Selected data, e.g. Amps, Voltage or Temperature, from battery or permanently powered End devices can be retrieved, logged ( Map points page), and presented ( viq configuration pages ) allowing building managers prevent outages, optimise the energy distribution and maintain building systems before any serious problem occurs. Each unit variant determines the maximum number of connected SonNet End devices, including a default of 20 points per End device (see Error! Not a valid bookmark selfreference.). It is designed and manufactured to comply with CE Class A, FCC Class A, WEEE (Waste Electrical and Electronic Equipment), RoHS (Restriction of Hazardous Substances) regulations and the identification of a substance as Substance of Very High Concern (REACH). 8 Issue 1, Jun. 2014

130 3 INSTALLATION GUIDE... 9 It also complies with the requirements defined in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied EN55022:1998/A1:2000+A2:2003 (class A) EN :2000 EN :1995/A1:2001 EN55024:1998/A1:2001+A2:2003 IEC :1995+A1:1998+A2:2000 IEC :1995+A2:2002 IEC :1995+A1:2000+A2:2001 IEC :1995+A1:2000 IEC :1996+A1:2000 IEC :1993+A1:2000 IEC :1994+A1: Issue 1, Jun. 2014

131 3 INSTALLATION GUIDE THE UNIT The unit includes internal web based (html5) Configuration pages, designed to simplify the engineering and configuration of the unit. The SIP SonNet-Trend displays each Sontay SonNet wireless End device communicating with the SonNet RF-RXS wireless receiver (connected at P1) as a Trend IQ3 controller on the Trend BMS Supervisor. It includes a set of pages that simplifies the Note configuration of the IP settings for identifying the SIP on the IP network configuration of communication requirements between the SIP and the SonNet RF-RXS wireless receiver, and the SIP and the Trend BMS configuration of the required End device points and the mapping to the required viq OS This product does not support alarms and plots Front Panel Annunciation The LEDs on the unit are arranged in a group that indicate the general status of this product, including Power, Ready and LAN communication activity and a group that shows the communications activity with slave devices on the Sontay SonNet RF-RXS wireless receiver. 8 Issue 1, Jun. 2014

132 3 INSTALLATION GUIDE... 9 Power LED This LED indicates the current status of the power applied to the unit. When continuously illuminated the 24VDC power is supplied. If the LED is off, the power is not supplied or has failed. 8 Issue 1, Jun. 2014

133 3 INSTALLATION GUIDE... 9 Ready LED This LED indicates the current status of the boot up process. When illuminated continuously the required files have been loaded to the RAM disk and the unit has successfully booted up. If the LED is off, the unit is not ready or has failed to boot up. Ethernet (Activity) LED This LED indicates the communication between this unit and the supervisory computer or controller connected via the Ethernet. When continuously illuminated the unit is currently connected to a device on the appropriate Ethernet cable. If general Ethernet communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected. The LED is off (extinguished) if a valid Ethernet connection is not detected. Serial Ports LEDs The P1 to P4 LEDs show the communication traffic between the unit and Sontay SonNet RF-RXS wireless receiver connected via the corresponding Serial port, P1. 8 Issue 1, Jun. 2014

134 3 INSTALLATION GUIDE... 9 If outgoing communications traffic is detected, the LED will extinguish irregularly as communications traffic is detected Button and Switches The unit is fitted with a recessed button for controlling the hardware and a Serial Interface switch for defining the Sontay SonNet RF-RXS wireless receiver communications standard. Caution Note Reset Button This recessed button is used to reboot the unit. Operating this button will perform a reboot that will restart the unit if the software fails. Only use the Reset button if the software reboot fails. DIP Switches The bank of 4 DIP switches is used to configure the Communications Standard used at P1 (see Hardware Control). The unit is also fitted with connections that support power, communications, and hardware expansion (see Hardware Control). 8 Issue 1, Jun. 2014

135 3 INSTALLATION GUIDE SYSTEM OVERVIEW The system architecture is shown below. 8 Issue 1, Jun. 2014

136 3 INSTALLATION GUIDE SonNet Network The Sontay SonNet radio system is a proprietary protocol solely for use with SonNet wireless End devices It. is comprised of a receiver, battery powered sensors and permanently powered routers. Routers, though permanently powered, can also have sensing elements, accomplishing both router and sensors functions. Note This unit is connected directly to the SonNet RF-RXS wireless receiver. The SonNet RF-RXS wireless receiver supports a maximum of 16 directly connected child devices (max. 12 battery powered nodes, and max. 4 routers). Routers support a maximum of 16 directly connected child devices (max. 8 battery powered nodes, and max. 8 routers). Caution Note A maximum depth of 8 layers of routers in a network and a maximum of 50 nodes per network is permitted, but is dependent on the SIP SonNet-BACnet product. Battery powered devices can only route their signals to the receiver directly or through routers, and not through other battery powered devices. Contact Sontay for a list of compatible End devices. 8 Issue 1, Jun. 2014

137 3 INSTALLATION GUIDE Trend Network The viq (Virtual IQ) software enables this unit to present each SonNet wireless End device as a Trend IQ3 controller (OS (out-station)), directly onto the Trend network via a defined VCNC Node and Port. The defined VCNC Node also represents a Node (OS) on the network. Remember OSs (and VCNCs) are subject to the constraints imposed by the Trend network, e.g. Node 2, Node 3 and Node 10 are reserved. Each transferred SonNet wireless End device value has a default configuration which relates to a standard Trend module (sensor, digital Input, knob, and switch). The viq has the full complement of functionality such as labels, alarms and plots. 8 Issue 1, Jun. 2014

138 14 HARDWARE GUIDE This hardware provides an interface between devices communicating via an identified protocol, i.e. SonNet, and Trend products communicating including 963, IQ4, IQ3 or IQ2 and EINC or XTEND via Ethernet protocol. The unit should be installed in systems for monitoring and control purposes. General Weight Power Input Power Consumption Default User name Default Password 330g per unit including DIN Rail clips 410g shipped including DIN Rail clips 24VDC ±15V regulated Admin (case-sensitive) password (case-sensitive) Hardware Details Button DIP Switch Reset 1 bank of 4 switches 10 Issue 1, Jun. 2014

139 Indicators Power, System Ready, Ethernet LAN Activity, 4 x Serial Communications Activity (one per port) Ethernet Serial 1 x 10/100Mbps port via RJ45 connector with 1.5KV magnetic isolation 1 x TTY port via RJ45 connector, supporting connection to Sontay SonNet RF-RXS wireless receiver Note Only P1 is configured via the DIP Switch. USB SD Memory Card 2 x USB2.0 compliant host ports supporting low-speed (1.5Mbps) and full-speed (12Mbps) data rate 1 x internal 2GB slot for storage expansion Environmental Storage Temperature Operating Temperature Regulations -20 to 80C (-4 to 176F), 0 to 90% Relative Humidity 0 to 70C (32 to 158F), 0 to 90% Relative Humidity CE Class A, FCC Class A, REACH (Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals - European Chemicals Agency), RoSH (Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment - EU Directive 2002/95/EC) 10 Issue 1, Jun. 2014

140 RoHS BANNED SUBSTANCES MAXIMUM LIMIT (PPM) Cadmium (Cd) 100 Lead (Pb) 1000 Mercury (Hg) 1000 Hexavalent Chromium (Cr6+) 1000 Poly Brominate Byphenyls (PBB) 100 Packing materials: Cadmium, Lead, Mercury, Hexavalent Chromium and its components < 100PPM 100 Dispose of the product and packaging according to WEEE Directive at an appropriate recycling centre. All parts are recyclable. The printed circuit board may be sent to any PCB recovery contractor to recover any appropriate metals. 10 Issue 1, Jun. 2014

141 15 INSTALLATION GUIDE This section explains the process of fitting the product in the required position and location, and connecting the cables to ensure it can communicate via the Trend network and the connected devices. It will explain specific wiring conventions used by the connected communications protocols and the hardware fitted to the unit. Note The CE marking on a product indicates the product complies with all the applicable European directives and applicable standards INSTALLING THE UNIT This unit usually forms part of a larger assembly, and/or may be housed in a floor or wallmounted enclosure. Note When fitting this unit as part of a system, refer to the documentation accompanying the other equipment for details. Caution This unit MUST be mounted to a DIN Rail in an enclosure using a DIN Rail kit. To install the unit using the DIN Rail kit 25. Fit the DIN Rail kit to the bracket on each side of the unit using the fixings supplied. 16 Issue 1, Jun. 2014

142 26. Simply click the unit, complete with the DIN Rail kit, onto the DIN Rail mounted in the enclosure. 16 Issue 1, Jun. 2014

143 27. Connect the power supply to the unit (see Connections and Wiring). Caution Before connecting power, ensure all connections have been verified and the V- (0V) is NOT earthed/grounded. Note A beep indicates the unit has started to boot up. 28. Connect this unit to the IP network using an appropriate Cat5e cable (see Connections and Wiring). 29. Connect this unit to the SonNet RF-RXS wireless receiver using an appropriate cable, (see Connections and Wiring). Remember The DIP Switches must be configured for connection to the SonNet RF-RXS wireless receiver, i.e. RS232 (see Connections and Wiring). 30. Configure the unit, including parameters required to permit communications via both the Ethernet and connection to the SonNet RF-RXS wireless receiver networks using the Configuration web pages (see Error! Not a valid bookmark self-reference.). 16 Issue 1, Jun. 2014

144 15.2 HARDWARE CONTROL The unit is fitted with 1 switchbank of 4 poles that are used to define the Serial port interface. It will be set to RS232 by default. A combination of pole 1 (SW1:p1) and pole 2 (SW1:p2) are used to configure the communications standard of Serial port 1 (P1). The switch 3 (SW1:p3) and switch 4 (SW1:p4) are not supported. SWITCH NO. (SW1) RS232 SIGNAL 1 (SW1:p1) ON 2 (SW1:p2) ON 3 (SW1:p3) N/A 4 (SW1:p4) N/A Note This unit also supports RS485 (2-wire+Gnd), and RS422 (4-wire+Gnd). However, these wiring standards are not applicable to the SonNet RX-RFS wireless receiver. 16 Issue 1, Jun. 2014

145 Connections and Wiring This unit may be supplied mounted in an enclosure or supplied as an individual part in kit form. Generally the unit will be installed as part of a control system using an Ethernet hub/switch. Category 5 cables may be used for individual line lengths of up to 100 metres. Caution Before connecting power to this unit, please ensure the Ethernet and Serial connections have been verified and the V- terminal (0 Volts) of the power connector is NOT earthed/grounded Power Supply Each unit requires a 24VDC power supply attached to the connector. If the power is correctly supplied the Power LED is illuminated and the real-time clock (RTC) will be maintained. Note The unit contains a supercapacitor that maintains the real-time clock for a maximum of 3 days. 16 Issue 1, Jun. 2014

146 Communications The RJ45 port(s), indicated by the symbol, is designed for Ethernet LAN, whereas the RJ45 ports at the opposite end of the unit supports M-Bus communications. Ethernet Communication Port Each unit contains 10/100base T port for Ethernet communications via a standard RJ45 type connector. Connection to an Ethernet hub/switch requires a Category 5 RJ45-to-RJ45 cable assembly. When connecting to the Ethernet hub/switch, a straight-through cable is used. RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 1 Transmit+ White/Orange 1 2 Transmit- Orange 2 3 Receive+ White/Green 3 4 N/A Blue 4 5 N/A White/Blue 5 6 Receive- Green 6 TO RJ45 PIN NO. 16 Issue 1, Jun. 2014

147 RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 7 N/A White/Brown 7 8 N/A Brown 8 TO RJ45 PIN NO. The image shows the flat side of RJ45 plug. When connecting directly to another device supporting 10/100base T Ethernet communications protocol, i.e. a laptop or computer used to configure and interrogate the unit, a crossover cable is required. RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 1 Transmit+ White/Orange 3 2 Transmit- Orange 6 3 Receive+ White/Green 1 4 N/A Blue 4 5 N/A White/Blue 5 6 Receive- Green 2 7 N/A White/Brown 7 TO RJ45 PIN NO. 16 Issue 1, Jun. 2014

148 RJ45 MALE FROM RJ45 PIN NO. SIGNAL COLOUR CODE (EIA/TIA 568B) 8 N/A Brown 8 TO RJ45 PIN NO. The image shows the flat side of RJ45 plug. 16 Issue 1, Jun. 2014

149 SonNet Communication Port Each unit contains RJ45 communication port that is used to establish communications with the connected SonNet RF-RXS wireless receiver. Serial port 1 (P1) is configured to support a RS232 communications standard. This is determined by the position of the SW1:p1 and SW1:p2 DIP switches. Note This unit also supports RS485 (2-wire+Gnd), and RS422 (4-wire+Gnd). These wiring standards are not applicable to the SonNet RX-RFS wireless receiver. FROM RJ45 PIN NO. RS232 SIGNAL SONNET RF-RXS 9-WAY D -TYPE 1 (White/Orange) DSR* 1 2 (Orange) RTS 2 3 (White/Green) GND 3 4 (Blue) TXD 4 5 (White/Blue) RXD 5 6 (Green) DCD* 6 7 (White/Brown) CTS 7 8 (Brown) DTR* 8 16 Issue 1, Jun. 2014

150 FROM RJ45 PIN NO. RS232 SIGNAL SONNET RF-RXS 9-WAY D -TYPE 9 Note The image shows the flat side of RJ45 plug. * indicates the signal is only available from Port 2 on RS232. CONNECTOR TYPES AND CABLES Shielded RJ45 connectors and screened Category 5 cables are widely available, however, specifications vary. In view of the problems that can arise with inadequate cabling, it is strongly recommended that ready-made interconnecting cables are used. 16 Issue 1, Jun. 2014

151 Hardware Expansion The unit is fitted with connections that support additional hardware to be connected to the unit. USB Port The USB host ports, indicated by the symbol, are USB2.0 high speed host ports. If necessary, you may be instructed to use these ports to transfer a file to the unit using a USB Flash device. The unit currently supports, Note USB Storage Device Contact the Sales/Service Engineer/Technical Support for details. Mini-USB Port This is not supported and will be obstructed by a label. 31. Configuration Guide). This page provides parameters used to identify individual OSs on the Trend network. 16 Issue 1, Jun. 2014

152 32. Configure the Trend Sensors, Digital Inputs, Knobs and Switches modules as defined in the Module field of the protocol dependant Map points page. 27 Issue 1, Jun. 2014

153 Configure the VCNCs The VCNCs (Virtual Communications Node Controller) provide parameters that define the interface between the virtual OSs configured in this product and the Trend network. Tip! The default parameters should only be edited if multiple Trend interface product occupy the same Trend LAN. Please contact technical support if problems occur. To configure the VCNC 33. Press to display the VCNC configuration window. This is used to configure the virtual connection from this product and the Trend network. x. Enter a Node number in the left side parameters. This is used to connect this product to the Trend network. Note Each node number is equivalent to an OS. This is also presented as OS in the BeMS. Node 2, Node 3 and Node 10 are reserved. 28 Issue 1, Jun. 2014

154 xi. Enter the Port number in the left side parameters. This is the number of the Ethernet port used to transfer messages between this product and a device on the Trend network. Caution xii. Enter the required Timeout value in seconds. This is used to automatically terminate the connection between this product and the Trend network when Ethernet communications has been lost. 34. Edit the Node number and Timeout in the right side parameters. These parameters define the internal virtual network connection. A Trend alarm will be asserted if a VCNC Node number is the same as a virtual OS (or VCNC Node ) when multiple Trend products occupy the same Trend LAN. 35. Press Save to confirm the internal and external VCNC changes. Tip! Use show the current status of the system, LAN and internetwork. 29 Issue 1, Jun. 2014

155 Configure the Time and Date The Time and date window displays the current time and date, and a selection of European time zones that are subject to DST (Daylight Savings Time). These parameters support the real-time clock that is used for measure plot intervals and time-stamping alarm messages. The time and date only requires editing after power has been applied, i.e. when installing this product or after a power failure. Note This product contains a supercapacitor that maintains the real-time clock for a maximum of 3 days. To configure the time and date 36. Press to display the real-time clock configuration window. These parameters provide the values that support the plot function and timestamping messages. Enter the time (hours and minutes) using the 24 hour clock notation, i.e. 14:45 is 02:45 pm. 30 Issue 1, Jun. 2014

156 Select the current date using the available menus for Year and Month, and selecting the appropriate date. Change the Time zone as necessary. This automatically applies the DST (Daylight Savings Time) configuration currently implemented by the selected location. GMT +/- TIME ZONE TIME ZONE TIME ZONE Universal Applies the configured time. Does not support DST. GMT Dublin, Lisbon, London Belfast, Isle_of_Man Guernsey, Jersey +01:00 Amsterdam, Berlin, Rome, Stockholm, Vienna Sarajevo, Skopje, Warsaw, Zagreb Belgrade, Bratislava, Budapest, Ljubljana, Prague Andorra, Gibraltar, Luxembourg, Malta Tirana Vaduz Vatican +02:00 Athens, Bucharest, Istanbul Helsinki, Riga, Sofia, Tallinn, Vilnius Chisinau, Simferopol Tiraspol, Uzhgorod +03:00 Moscow, Samara Brussels, Copenhagen, Madrid, Paris Monaco, Oslo, Podgorica, San_Marino Kaliningrad, Kiev, Mariehamn Minsk, Nicosia 37. Press Save to confirm time and date changes. 31 Issue 1, Jun. 2014

157 Configure the UDP Group The UDP (User Datagram Protocol) window shows a group number used to identify a group of devices communicating via the IP (Internet Protocol). This restricts communications to only devices in the same UDP group. To configure the UDP group number 38. Press to display the Set UDP group dialogue. This shows the group number corresponds to an Ethernet port number used to transmit messages to other devices in the same UDP group. Edit the UDP group number as necessary. 32 Issue 1, Jun. 2014

158 Trend Internetwork SIP SonNet-Trend - Interface Range Tip! Having separate sites, i.e. different UDP groups, enables the LAN number to be duplicated. OS11 UDP Group: LAN: 12 Human: Apartment (Site A) Machine: AFD2EFG1-G07G-FFFG-G6B2-FGG90DD3EDFG OS11 OS27 OS11 OS42 OS11 UDP Group: LAN: 12 Human: Offices (Site B) Machine: FAE6DCB7-A10A-DDDA-B2F8-DBB10EE6DECB OS11 OS27 OS11 OS42 OS11 UDP Group: LAN: 13 Human: Offices (Site B) Machine: FAE6DCB7-A10A-DDDA-B2F8-DBB10EE6DECB OS11 OS27 OS11 OS42 33 Issue 1, Jun. 2014

159 39. Press Save and reboot to confirm the UDP group changes and restart this product. It automatically restarts (as confirmed by a beep ) and loads the Login page Configure the GUID The GUID (Global Unique Identifier) window shows the editable site codes that are used to assist with identifying the source of IP Alarms if multiple sites BeMS system. To configure the GUID 40. Press to display the Set GUIDs dialog. This displays the Machine GUID and Human GUID showing the Trend site details. Enter the Human GUID. A maximum 30 characters are used to identify the BeMS site (equivalent to the Site name in 34 Issue 1, Jun. 2014

160 Trend SET). Note It is specifically used in remote alarms to identify the alarm source (see Configure a Sensors Module and Configure a Digital Inputs Module) on a multi-site system, e.g. if multiple UDP Groups are configured. Change the Machine GUID. This is a unique site identifier and must be identical for all units on the site. All viq OSs will be assigned this configured Machine GUID. 35 Issue 1, Jun. 2014

161 Trend Internetwork SIP SonNet-Trend - Interface Range OS11 UDP Group: LAN: 12 Human: Apartment (Site A) Machine: AFD2EFG1-G07G-FFFG-G6B2-FGG90DD3EDFG OS11 OS27 OS11 OS42 OS11 UDP Group: LAN: 12 Human: Offices (Site B) Machine: FAE6DCB7-A10A-DDDA-B2F8-DBB10EE6DECB OS11 OS27 OS11 OS42 OS11 UDP Group: LAN: 13 Human: Offices (Site B) Machine: FAE6DCB7-A10A-DDDA-B2F8-DBB10EE6DECB OS11 OS27 OS11 OS Press Save to confirm changes to the GUID details. 36 Issue 1, Jun. 2014

162 Save Plots to Flash The Save Plots provides functionality to save the current plot values. Saving these values ensures all selected plot data is included when a Backup is performed. Note The plot data will be automatically loaded when the SIP_Backup file is restored. 42. Press to display the Save plots to flash dialog. Note Caution Press Save to confirm all current rend Sensor Module plot data is to be saved. This can prevent the loss of data before using the Restore function. Plot data is saved at regular 6 hours intervals, 4 times a day at 00:00, 06:00, 12:00 and 18:00. Performing this operation does not affect this function. Rebooting or removing the power from this product before all plot 37 Issue 1, Jun. 2014

163 data is saved may corrupt plot data files or cause loss of essential data. It takes about 1.5 secs to save a plot data file, and approximately 20 mins to save the maximum 1024 plot data files. 43. Press Cancel to close the dialog. 38 Issue 1, Jun. 2014

164 Internetwork SIP SonNet-Trend - Interface Range Check the Network Status Note The displays a dialog showing the current status of the system, LAN and Internetwork. It can be used to diagnose and indicate network problems. OS11 An Internetwork is a communication link between LANs, (Local LAN is local to the connection, and Remote LAN a Local Area Network (LAN) accessed from the reference device via the Internetwork). It is a network to which a number of OS (nodes) are connected; each OS (nodes) is used to connect a LAN, i.e. the VCNC port. 44. Press to display the Network Status dialog. LAN 5 (VCNC Node 4) OS42 OS11 OS11 LAN 6 (VCNC Node 4) OS26 OS11 OS27 LAN 6 (VCNC Node 5) OS42 OS11 OS27 OS11 OS18 OS11 OS34 OS11 PARAMETER System Uptime DESCRIPTION The amount of time this product has been operating, i.e. since this product 39 Issue 1, Jun. 2014

165 PARAMETER Lan OK Time Lan Status DESCRIPTION was last turned on or rebooted. The amount of time the LAN has been successfully communicating on the Trend network, i.e. since the last build process was successful. The current condition of the LAN corresponding to this product and the time remaining until a Timeout will occur. Status includes Lan POWERUP The LAN build process is starting. Lan DEAF The comms with other Trend network devices are not applicable (only 1 (one) device in LAN) or not available (more than 1 (one) device in LAN, see LAN BROKEN ). Lan BROKEN A comms failure with other devices on the LAN. Typically, due to a timeout caused by Ethernet wiring or connection problem, an IP address that is sending but not receiving messages, duplicate OS numbers from identified IP address on the LAN or when a LAN is changed, i.e. identified IP address is added or removed. Lan BUILT The LAN build process is successful. Lan OK! Successful LAN comms are detected if 40 Issue 1, Jun. 2014

166 PARAMETER Last Lan Message continued Internetwork OK Time Internetwork Status DESCRIPTION product is not alone on local LAN or if it can communicate with other devices on the local LAN. The last message from describing the LAN status, see Lan Status. continued The amount of time the Internetwork has been successfully communicating, i.e. since the last Internetwork build process was successful. The current condition of the Internetwork assigned to this product and the time remaining until a Timeout will occur. Status includes Internetwork POWERUP Internetwork DEAF Internetwork BROKEN The Internetwork build process is starting. The comms failure with other Trend network devices are not applicable (only 1 (one) device in Internetwork) or not available (more than 1 (one) device in Internetwork, see Internetwork BROKEN ). An Internetwork comms failure. Typically, due to a timeout caused by an Ethernet 41 Issue 1, Jun. 2014

167 PARAMETER DESCRIPTION Internetwork BUILT wiring or connection problem, duplicate Lan numbers from an identified IP address on the Internetwork or when the Internetwork is changed, i.e. identified IP address is added or removed. The Internetwork build process is successful. Internetwork OK - Timeout in nn Successful Internetwork communications and number of seconds until Timeout is detected, i.e. when nn shows 00. Last Internetwork Message The last message from describing the Internetwork status, see Internetwork Status. Tip! If necessary, correct any issues that may be indicated. If necessary, use SIP Search to ensure IP Addresses are unique. Use iptool to ensure LAN numbers (and VCNC Node numbers where necessary) are unique. viq is identified by the viq3 type reference in iptool. 45. Press Close to remove the dialog. 42 Issue 1, Jun. 2014

168 43 Issue 1, Jun. 2014

169 Configure the Address Module The Trend Address module page displays information relating to the selected virtual OS. If the supervisor (IQView or 963) connection to the VCNC is permanent, the viq OS can send Trend LAN type alarms (IQ system alarms using LAN and outstation addressing) to the Virtual OS Identifier Trend LAN Alarms Control Standard Alarms enabled Trend Node transferring Alarm Messages Trend LAN number of Node transferring Alarm Messages Trend IP Alarms Control IP Alarms enabled IP Address of Trend Controller transferring Alarm Messages 44 IP Port of Trend Issue 1, Jun Controller transferring Alarm Messages

170 VCNC used for the connection to 963. To send Trend IP alarms, the alarm destination module needs to be set up with the supervisor s IP address and port number. On multi-site systems all viq OSs on a site must be setup with the same GUID settings (which are both unique to that site) in order for reliable receipt of IP address type alarms. Caution Identifier does not support \ / ( { ;, : invalid characters. 45 Issue 1, Jun. 2014

171 Meter Address 01 Configuration Meter Address 04 Configuration Detects Alarm Condition Meter Address 05 Configuration Device Mapping Device Mapping Device Mapping OS011 Address Module details OS012 Address Module details OS013 Address Module details IP Network SIP SonNet-Trend - Interface Range To configure the module details 46. Select the OS and press the Address option to show parameters used to identify each individual virtual OS and configure the alarm message transmission path. LAN Port IP Alarm Port Supervisory Computer (IP Address or Remote LAN and Node number) Tip! xiii. Select the required OS and press Address if the Address Module details are not displayed. The text above the Module type buttons identifies the selected out-station. IP Alarm Port LAN Port If necessary, enter text in the Identifier field. This identifies the OS associated with the defined slave in this product and BeMS. Network Configuration xiv. Configure the alarm message transmission path. To use Trend LAN alarm Device Configuration 46 Issue 1, Jun Meter Meter Meter Addr. 01 Addr. 04 Addr. 05 (OS011) (OS012) (OS013) P1

172 Enter the Alarm Address number. This identifies the device on the Ethernet network used to display alarms generated by the third party devices on the network. Enter the On Remote LAN number. This identifies the LAN that includes the device on the Ethernet network used to display asserted alarms. Note To use Trend IP alarm Enable IP alarms (Internet Protocol), i.e. Use IP alarms. This allows the transmission of IP alarm signals, but not Trend alarms, to the BeMS. Enter the IP address. This identifies the device on the BeMS that will receive alarms messages. Enter the Port number. This identifies the internal port used to receive IP alarm messages. The IP address must be configured according to local company network policy. 47. Press Save to confirm the Trend Address module changes. (see The Configuration Pages). 47 Issue 1, Jun. 2014

173 Configure a Sensors Module The Sensors page displays read-only Integer values in the specified engineering units recorded by the corresponding device. The parameters on this page are also used to define and enable required alarm levels and determine the plot intervals. Device Parameter Identification Shows Recorded Value Engineering Data Unit High and Low Alarm Limit Alarm Limit Control Plot Control and Interval 48 Issue 1, Jun. 2014

174 To configure a Sensor module 48. Select the OS and press the Sensors option to display the Sensor module configuration page. xv. Locate the Index number corresponding to the Mod. num. configured on the Map points page. xvi. Enter text (40 characters max) used to identify the associated parameter in the Label field. This is used to identify the parameter in the BeMS. It should be a concise description of the parameter. Caution The Label does not support \ / ( { ;, : invalid characters. xvii. Inspect the Value field. This displays the value recorded from the parameter associated with the Module number configured on the Map points page. xviii. Enter the appropriate engineering data value type in the Unit field. This appears in the BeMS and is used to identify the engineering data value, i.e. A (amps) if scaling a value measuring a ma signal. 49 Issue 1, Jun. 2014

175 50 Issue 1, Jun. 2014

176 If necessary, enter a value used to specify the high alarm limit in H. Lim. and/or the low alarm H. Lim Alarm asserted if H. Enab is limit in L. Lim.. This is used to define the upper and/or lower limits of the value recorded from H. Lim the parameter. If a limit is exceeded the Alarm corresponding alarm in the BeMS will only be asserted if H. Enab. and/or L. Enab. is L. Lim Alarm enabled (). Remember A configured low alarm limit value must be less than the defined high alarm limit. L. Lim Alarm asserted if H. Enab is If necessary, enable () the high alarm limit ( H. Enab. ) and/or low alarm limit ( L. Enab. ). This control the high alarm and low alarm indication in the BeMS, when the value recorded from the parameter asserts an alarm state determined by the value defined in H. Lim. and/or L. Lim.. If this field is disabled () an alarm state will not be indicated. If necessary, enable () the plot function. This allows the Trend graph in the BeMS to plot Issue 1, Jun. 2014

177 value records from the parameter. If this field is disabled () a Trend will not be generated. Note A Trend is a graphical representation of a value from a defined point at regular time periods. The time period is synchronised to the real-time clock in this product. The Trend Sensor module appears as the value in Plots page of Trend BeMS. Tip! Plot data logged in this product can be recorded by the Trend Supervisor (963) before it is overwritten using the RECORDAUTO_COMPACT action or RECORDAUTO_PRECISION action. This is automatically run when Buffer Ready Events (BBUF) are received from this product. Refer to Trend Controls documentation for details. Tip! If necessary, select the required plot interval, from 1 minute to 24 hours. This defines the period of time between each plot of the corresponding recorded value on the Trend graph in the BeMS. Press Copy/paste data button to display a dialog. Use Copy to clipboard to add all the module information (excluding Values) to the computer clipboard, or click the right hand mouse button in the white square and select Paste from the context menu to add copied information to the Module page. Module information can be edited using.csv editing software, e.g. Microsoft Excel. 52 Issue 1, Jun. 2014

178 49. Press Save to confirm Trend Sensors Module changes Configure a Digital Inputs Module The Digital Inputs page displays read-only Boolean values recorded by the parameter in the corresponding third party device. The parameters on this page are used to enable required alarms and inspect and control the status of a specific engineering data value from this product. Device Parameter Identification Shows Current Digital Value Alarm Control Shows Required Digital Value To configure the Digital Inputs module 53 Issue 1, Jun. 2014

179 50. Select the OS and press the Digital Inputs option to display the Digital Input module configuration parameters. Caution xix. Locate the Index number corresponding to the Module number configured on the Map points page. xx. Enter text (40 characters max) in the Label field. This is used to identify the parameter in the controller. It should be a concise description of the engineering data value. The Labels does not support \ / ( { ;, : invalid characters. xxi. Inspect the Status field. This displays the current condition of the recorded Digital Input value. If necessary, enable () the alarm detection state in Alarm enable. This controls the alarm indication when the recorded value asserts an alarm state, determined by the Required Status. If this field is disabled () an alarm state will not be indicated. If necessary, define the required alarm indication state in the Required Status field. A healthy state is shown if Status is (1, True, Enabled, or On), and Required Status is (0 (zero), False, Disabled, or Off). An unhealthy state (alarm state asserted) is shown Status Required Status Alarm Asserted True False True False 54 Issue 1, Jun. 2014

180 if the Status and the Required Status are the same. Tip! Press Copy/paste data button to display a dialog. Use Copy to clipboard to add all the module information (excluding Status) to the computer clipboard, or click the right hand mouse button in the white square and select Paste from the context menu to add copied information to the Module page. Module information can be edited using.csv editing software, e.g. Microsoft Excel. 51. Press Save to confirm Trend Digital Inputs Module changes Configure a Knobs Module The Knobs page displays read and write Integer values in the specified engineering units recorded by the parameter in the corresponding third party device. The parameters on this page are used to configure the authorisation level required to inspect and/or control a specified Knob Module value within the defined limits. Device Parameter Identification Shows Recorded Value Engineering Data Unit Upper and Lower Limit Access Level 55 Issue 1, Jun. 2014

181 To configure a Knob module 52. Select the OS and press the Knobs option to display the Knob module configuration page. xxii. Locate the Index number corresponding to the Module number configured on the Map points page. xxiii. Enter text used to identify the parameter in the Label field. This is used to identify the value in this product and the BeMS. It should be a concise description value. Caution Note The Label does not support \ / ( { ;, : invalid characters. xxiv. Inspect the Value field. This field will display the value recorded from the parameter associated with the Module number configured on the Map points page. If an authorisation level has been configured, an appropriate pin number must be entered correctly before a write command to this module type can be confirmed. 56 Issue 1, Jun. 2014

182 xxv. Enter the appropriate engineering data value type in Write min. the Unit field. This appears in the BeMS and is used Max value to identify the engineering data value recorded, i.e. A (amps) if scaling a value measuring a ma signal. T. Lim If necessary, enter a value used to specify the maximum value allowed in T. Lim. and/or minimum value allowed in the B. Lim.. This is used to define the maximum and/or minimum value that can be written to the parameter using the corresponding engineering units. B. Lim Write max. value Min Tip! Enter the required Pin level number. This is the authorisation level used to prevent un-authorised access to the engineering data. A Pin level number should already have been configured via the Users page (see Configure the Pin Level Authorisation). Press Copy/paste data button to display a dialog. Use Copy to clipboard to add all the module information (excluding Values) to the computer clipboard, or click the right hand mouse button in the white square and select Paste from the context menu to add copied information to the Module page. Module information can be edited using.csv editing software, e.g. Microsoft Excel. 53. Press Save to confirm the Trend Knobs Module changes. 57 Issue 1, Jun. 2014

183 58 Issue 1, Jun. 2014

184 Configure a Switches Module The Switches page displays read and write Boolean values that have been recorded by parameter in the corresponding third party device. The parameters on this page are used to inspect and/or control the status and authorisation level. Device Parameter Identification Shows Recorded Value Access Level To configure the Switch module 59 Issue 1, Jun. 2014

185 54. Select the OS and press the Switches option to display the Switch module configuration parameters. Caution Note xxvi. Locate the Index number corresponding to the Module number configured on the Map points page. xxvii. Enter text used to identify the parameter in the Label field. This is used to identify the parameter in the controller. It should be a concise description of the parameter. The Label does not support \ / ( { ;, : invalid characters. xxviii. Inspect the Status. This shows the current condition of the corresponding parameter in the Switch module, where is 1, True, Enabled or On. If an authorisation level has been configured, an appropriate pin number must be entered correctly before a write command to this module type can be confirmed. xxix. Enter the required Pin level number. This is the authorisation level used to prevent unauthorised access to the parameter. A Pin level number should already have been configured via the Users page (see Configure the Pin Level Authorisation). Tip! Press Copy/paste data button to display a dialog. Use Copy to clipboard to add all the module information (excluding Status) to the computer clipboard, or click the right hand mouse button in the white square and select Paste from the 60 Issue 1, Jun. 2014

186 context menu to add copied information to the Module page. Module information can be edited using.csv editing software, e.g. Microsoft Excel. 55. Press Save confirm the Trend Switches Module changes Configure the Pin Level Authorisation A maximum of six authorisation levels, Pin Levels and associated Pin Numbers, can be configured via the Users page which is displayed when Users is selected. Each Pin Level determines the minimum level of authorisation required to change module parameters. Any Pin Level of 94 or below only permits changes to the values on Knobs pages and status on the Switches pages. However, a Pin Level of 95 or above permits changes to all module parameters, and includes Labels, Units and changing the Pin Numbers that are assigned to a Pin Level less than current Pin Level. Caution Always configure an administrative Pin Level first (Pin Level 99). Values will not appear on the viq pages if a Pin number is configured, but the Trend security is NOT. To configure the authorisation levels 61 Issue 1, Jun. 2014

187 56. Select the OS and press the Users option to display the Pin Level configuration page. Each Pin Level is associated with a Pin Number that is used to confirm the current users authorisation to change the edited parameter. xxx. Enter a Pin level number in the range 0 to 99. This number is an authorisation level relating to the Pin Number. Note Pin Numbers are assigned to groups of virtual OS via the Trend Security page (see Configure the Module Authorisation). 62 Issue 1, Jun. 2014

188 xxxi. Enter a maximum four digit security number in the Pin Number field. This number is used to confirm the user is allowed to change a module parameter using Text comms. Note Text comms enables user-entered read and write requests to module parameters. 57. Press Save to confirm the Trend Users changes. (see The Configuration Pages) USE THE VIQ CALCULATOR The viq Calculator page allows the user to influence an output value to a specified Module type by performing a sequence of up to 5 operations at specified intervals. Each operation is constructed using a combination of values sourced from a defined Module number at a specified OS or a user defined fixed value. A B Operation performed Note A and B - Fixed Value or viq Module Value O - Output (Result of A and B) O A B Operation performed O Output value Written to Destination 63 Issue 1, Jun. 2014

189 The final operation provides an output that should be written and stored at an unused Module number in the defined OS. This may be the partial result of a combination of multiple viq Calculations which produces a completed result at a scheduled frequency. This is useful when investigating energy usage. Example This example shows 2 viq Calculations that provide partial results for a third viq Calculation. Index 0 shows the total usage over the last configured calculation period and writes the value to an unused Module number at a defined out-station. Index 1 shows the starting usage from second unused Module number at a Record 2 Calculation (A-B) Value Value at Module number in defined OS (e.g. kwh) Record 0 Start of period value True False Time True writes Input A (e.g. kwh) to unused Module number destination. This is Input B in calculation record 2. Record 1 Total period value True False True writes Input A (determined by Record 2 Destination) to unused Module number destination that is configured to plot. True calculates result of A-B Operand, where Input A is record 2 and Input B is record 1. Writes Record 2 True result to unused Module Number that is source Current value in period for record 0. False 64 Issue 1, Jun Configured Calculation Frequency Configured Calculation written to unused Module at specified OS

190 defined out-station. Index 2 calculates the total usage at configured intervals. This page provides sections that, Calculation Table Frequency Schedule or Operation 65 Issue 1, Jun Buttons to Manage Graphical Operation Calculations Icons

191 identify and manage each calculation, show the sequence of operations combined for a selected calculation, configure the frequency of a selected calculation and each operation (e.g. A+B, A-B, etc.) in the calculation. Note The Calculator supports a maximum of 1000 calculations. 66 Issue 1, Jun. 2014

192 Create the viq Calculation Each viq Calculation is referenced using an In (dex) number and is performed at intervals determined by the configured Frequency schedule. The In number is identified by a Label that can be edited to clarify the purpose of the individual viq Calculation. Remember The Calculator supports a maximum of 1000 calculations. To create a viq Calculation, 58. Press and select viq Calculator from the list of available options. The viq Calculation table is used to track viq Calculations by assigning an In number to a specific calculation. It also shows the total number of calculations configured. 67 Issue 1, Jun. 2014

193 xxxii. Create a blank viq Calculation. Press to the bottom of the list. to add a default viq Calculation 68 Issue 1, Jun. 2014

194 The list of viq Calculations can be re-ordered by dragging a selected viq Calculation to any position. Note The In number will remain out of numerical sequence until Save is used to confirm the changes. 69 Issue 1, Jun. 2014

195 Alternatively, use Move to to display a dialog. This requests the In number that precedes the selected viq Calculation, e.g. select In 81 and type 30 to move it to In 31 (the In number will remain as 81 until saved). viq Calculation(s) can be deleted using the Delete option from the context menu. Tip! Note viq Calculation(s) can be duplicated using the to create a specific number of calculations (see Replicate an Existing viq Calculation). xxxiii. Change the text in the Label field used to identify the calculation. It is useful to include the source Trend OS and Module. The Frequency of a blank calculation is scheduled to Never, i.e. it will not run. Use the in the graphical viq Calculation to display parameters that configure frequency schedule. 59. Press Save to confirm the viq Calculator changes. 70 Issue 1, Jun. 2014

196 Configure the viq Calculation Each viq Calculation produces an output value written to a defined Module Type. It performs simple mathematical operations using either a value sourced from a defined Module number in a specified out-station and/or a user defined fixed value. The viq Calculation Index is a reference to 5 (five) graphically represented operations displayed below the viq Calculation table. Note Each viq Calculation can be scheduled using parameters that are displayed when the is pressed. Input A Value Input B Value Operation Configuration Icon Destination Outstation/Module Configuration Icon Frequency Schedule Configuration Icon No Operation Fixed Value Input Configured Operation 71 Issue 1, Jun. 2014

197 To configure a viq Calculation 60. Select the required viq Calculation. Initially, a sequence of 5 pre-defined No Operation mathematical operations, i.e. the input value will remain unchanged. 61. Configure the Input A and B values. xxxiv. type. Configure Source (Input A) value Select Source (Input A) icon to display the parameters used to define the Source Input A value. Define the origin of Input A value by selecting a Fixed value (user defined value) or Module (Module number in a specified outstation) Operand type. If Fixed value is selected, enter the required value at the Fixed value parameter. 72 Issue 1, Jun. 2014

198 If Module is selected, define the required OS number at OS, define the number of the Module at Module number and select the corresponding type of Module at Module type. xxxv. Configure the mathematical operation. Select the Input B icon to display the parameters used to configure the mathematical operation. Note xxxvi. Select the mathematical operation used to determine the output using the values derived from Input A and Input B at the Operation type. Input A is already defined from the Source or previous operation. 73 Issue 1, Jun. 2014

199 OPERATION TYPE DESCRIPTION NOP Input value is unchanged, No Operation A + B Add A and B (e.g = 12) A - B Subtract B from A (e.g. 9 3 = 6) B - A Subtract A from B (e.g. 3 9 = -6) A x B Multiply A by B (e.g. 9 x 3 = 27) A / B Divide A by B (e.g = 3.1) B / A Divide B by A (e.g. 3 9 =.333) INT(A / B) Divide A by B (e.g = 3), whole integers, no decimal places INT(B / A) Divide B by A (e.g. 3 9 = 0), whole integers, no decimal places A squared <A 2 > Multiply A by A (e.g. 9 x 9 = 81) A cubed <A 3 > Multiply A by A by A (e.g. 9 x 9 x 9 = 729) A to the power of B <A B > Multiply A by A using B to define the power ratio (e.g. if B = 5, sum 9 5 = 9 x 9 x 9 x 9 x 9 = 59,049) 2 to the power of A <2 A > Multiply 2 by 2 using A to define the power ratio (e.g. if A = 9, sum 2 9 = 2 x 2 x 2 x 2 x 2 x 2 x 2 x 2 x 2 = 512) 10 to the power of A <10 A > Multiply 10 by 10 using A to define the power ratio (e.g. if A = 9, sum 10 9 = 10 x 10 x 10 x 10 x 10 x 10 x 10 x 10 x 10 = ) 74 Issue 1, Jun. 2014

200 OPERATION TYPE DESCRIPTION B to the power of A <B A > Multiply B by B using A to define the power ratio (e.g. A = 9, sum 3 9 = 3 x 3 x 3 x 3 x 3 x 3 x 3 x 3 x 3 = 19,683) Square root of A A = n 2 (e.g. 9 = 3 x 3) A % B A% of B (e.g. 50% of 200 = 100) Truncate A Ignores decimal places (e.g. Truncate = 9) A Modulus B Divide A by B and display the remaining value (e.g. if 10 3 = 3 + remainder 1, then 10 Modulus 3 = 1) xxxvii. Define the origin of Input B value by selecting a Fixed value (user defined value) or Module (Module number in a specified out-station) Operand type. If Fixed value is selected, enter the required value at the Fixed value parameter. If Module is selected, define the required Out-station number at OS, define the number of the Module at Module number and select the corresponding type of Module at Module type. 75 Issue 1, Jun. 2014

201 Tip! All this information should be available on the viq configuration pages. If necessary, configure the remaining mathematical operations as required using the previous instructions. 62. Configure the destination OS and module type used to display the output value. This corresponds to an OS and Trend Module type on the viq configuration pages. xxxviii. Select the Destination OS/Module Type configuration icon to display the parameters used to identify the OS and module type used to display the output value. xxxix. Enter the required OS number at OS, the number of the module at Module number and select the corresponding type of module at Module type (Sensor (S), Digital Input (I), Knob (K), or Switch (W)). 76 Issue 1, Jun. 2014

202 Configure the Frequency schedule The Frequency schedule determines the time period between repeating the selected viq Calculation. A viq Calculation can be configured to occur at a pre-defined time period or at a user defined time period. To configure the Frequency schedule 77 Issue 1, Jun. 2014

203 63. Select the Frequency configuration icon to display parameters that configure calculation schedule. Calculations can be configured to occur at a predefined time period or a user defined time period. Select a pre-defined or user defined time schedule in Calculation frequency. A pre-defined schedule performs the calculation at specific occurrences, i.e. At first run, At midday, At midnight, A new month, A new year or Never. The calculation will not be performed if Never is selected. A user defined schedule performs the calculation at regular periods, i.e. Every given seconds, Every given minutes, Every given hours, or Every given days determined by the value configured in Parameter, i.e. if Parameter is 10, and Calculation frequency is Every given hours the calculation will be performed at regular intervals of 10 hours. 78 Issue 1, Jun. 2014

204 64. Press Save to confirm viq Calculator Frequency changes. 79 Issue 1, Jun. 2014

205 Replicate an Existing viq Calculation Sometimes, an existing viq Calculation will perform a sequence of mathematical operations that are also applicable or similar to the requirements of other viq Calculations. By selecting a calculation record and replicating the associated viq Calculation, the corresponding sequence of mathematical operations can be automatically assigned to a defined out-station and module in each viq Calculation. Example This shows the automatic configuration of out-station numbers when replicating an existing viq Calculation. This can also apply to module numbers. 1 3 Existing viq Calculation 2 3 First Replicated viq Calculation 2 2 Second Replicated viq Calculation 80 Note The S(I, K, or W)n number will be adjusted, if Module numbers is Issue 1, Jun selected in Changing. 3

206 To replicate an existing viq Calculation 65. Select a viq Calculation that is applicable or similar to the requirements of another viq Calculation. This may be a viq Calculation that processes a value using the same or similar sequence of mathematical operations that can be used by one or more other OS or modules. 81 Issue 1, Jun. 2014

207 xl. Replicate the selected viq Calculation record. Press to display the parameters used to configure how the selected viq Calculation must be adjusted. Enter the number of calculations to be added to the viq Calculation table in Replicate. The additional calculation records are automatically populated using the selected viq Calculation. Select OS numbers or Module numbers in Changing. This determines the numerical references that are adjusted when the viq Calculation corresponding to the selected calculation record is replicated, i.e. if OS numbers is selected, all numerical out-station references in each mathematical operation is offset by the value defined in Adding, or if Module numbers is selected, all numerical Module references in each viq Calculation are offset by the value defined in Adding. 82 Issue 1, Jun. 2014